DAC101S101 10-Bit Micro Power Digital-to-Analog Converter with Rail-to-Rail Output General Description Features The DAC101S101 is a full-featured, general purpose 10-bit voltage-output digital-to-analog converter (DAC) that can operate from a single +2.7V to 5.5V supply and consumes just 175 µA of current at 3.6 Volts. The on-chip output amplifier allows rail-to-rail output swing and the three wire serial interface operates at clock rates up to 30 MHz over the specified supply voltage range and is compatible with standard SPI™, QSPI, MICROWIRE and DSP interfaces. Competitive devices are limited to 20 MHz clock rates at supply voltages in the 2.7V to 3.6V range. n n n n n n n n The supply voltage for the DAC101S101 serves as its voltage reference, providing the widest possible output dynamic range. A power-on reset circuit ensures that the DAC output powers up to zero volts and remains there until there is a valid write to the device. A power-down feature reduces power consumption to less than a microWatt. The low power consumption and small packages of the DAC101S101 make it an excellent choice for use in battery operated equipment. The DAC101S101 is a direct replacement for the AD5310 and is one of a family of pin compatible DACs, including the 8-bit DAC081S101 and the 12-bit DAC121S101. The DAC101S101 operates over the extended industrial temperature range of −40˚C to +105˚C. Guaranteed Monotonicity Low Power Operation Rail-to-Rail Voltage Output Power-on Reset to Zero Volts Output SYNC Interrupt Facility Wide power supply range (+2.7V to +5.5V) Small Packages Power Down Feature Key Specifications n n n n n n Resolution 10 bits DNL +0.15, -0.05 LSB (typ) Output Settling Time 8 µs (typ) Zero Code Error 3.3 mV (typ) Full-Scale Error −0.06 %FS (typ) Power Consumption — Normal Mode 0.63 mW (3.6V) / 1.41 mW (5.5V) typ — Pwr Down Mode 0.14 µW (3.6V) / 0.33 µW (5.5V) typ Applications n n n n Battery-Powered Instruments Digital Gain and Offset Adjustment Programmable Voltage & Current Sources Programmable Attenuators Pin Configuration 20154102 20154101 Ordering Information Order Numbers Temperature Range Package DAC101S101CIMM −40˚C ≤ TA ≤ +105˚C MSOP X62C DAC101S101CIMMX −40˚C ≤ TA ≤ +105˚C MSOP Tape-and-Reel X62C DAC101S101CIMK −40˚C ≤ TA ≤ +105˚C TSOT X63C DAC101S101CIMKX −40˚C ≤ TA ≤ +105˚C TSOT Tape-and-Reel X63C DAC101S101EVAL Top Mark Evaluation Board SPI™ is a trademark of Motorola, Inc. © 2005 National Semiconductor Corporation DS201541 www.national.com DAC101S101 10-Bit Micro Power Digital-to-Analog Converter with Rail-to-Rail Output June 2005 DAC101S101 Block Diagram 20154103 Pin Descriptions TSOT (SOT-23) Pin No. MSOP Pin No. Symbol Description 1 4 VOUT DAC Analog Output Voltage. 2 8 GND Ground reference for all on-chip circuitry. 3 1 VA Power supply and Reference input. Should be decoupled to GND. 4 7 DIN Serial Data Input. Data is clocked into the 16-bit shift register on the falling edges of SCLK after the fall of SYNC. 5 6 SCLK Serial Clock Input. Data is clocked into the input shift register on the falling edges of this pin. 5 SYNC Frame synchronization input for the data input. When this pin goes low, it enables the input shift register and data is transferred on the falling edges of SCLK. The DAC is updated on the 16th clock cycle unless SYNC is brought high before the 16th clock, in which case the rising edge of SYNC acts as an interrupt and the write sequence is ignored by the DAC. 2, 3 NC 6 www.national.com No Connect. There is no internal connection to these pins. 2 Storage Temperature −65˚C to +150˚C (Notes 1, 2) Operating Ratings (Notes 1, 2) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Operating Temperature Range 6.5V Supply Voltage, VA Voltage on any Input Pin Package Input Current (Note 3) Power Consumption at TA = 25˚C ESD Susceptibility (Note 5) Human Body Model Machine Model Soldering Temperature, Infrared, 10 Seconds (Note 6) +2.7V to 5.5V Any Input Voltage (Note 7) −0.3V to (VA + 0.3V) Input Current at Any Pin (Note 3) −40˚C ≤ TA ≤ +105˚C Supply Voltage, VA −0.1 V to (VA + 0.1 V) Output Load 10 mA 0 to 1500 pF SCLK Frequency 20 mA See (Note 4) Up to 30 MHz Package Thermal Resistances 2500V 250V Package θJA 8-Lead MSOP 240˚C/W 6-Lead TSOT 250˚C/W 235˚C Electrical Characteristics Values shown in this table are design targets and are subject to change before product release. The following specifications apply for VA = +2.7V to +5.5V, RL = 2kΩ to GND, CL = 200 pF to GND, fSCLK = 30 MHz, input code range 12 to 1011. Boldface limits apply for TMIN ≤ TA ≤ TMAX: all other limits TA = 25˚C, unless otherwise specified. Symbol Parameter Conditions Typical (Note 9) Limits (Note 9) Units (Limits) 10 Bits (min) STATIC PERFORMANCE Resolution Monotonicity INL Integral Non-Linearity DNL Differential Non-Linearity 10 Bits (min) Over Decimal codes 12 to 1011 ± 0.6 ± 2.8 LSB (max) VA = 2.7V to 5.5V +0.15 +0.35 LSB (max) −0.05 −0.2 LSB (min) ZE Zero Code Error IOUT = 0 +3.3 +15 mV (max) FSE Full-Scale Error IOUT = 0 −0.06 −1.0 %FSR (max) GE Gain Error All ones Loaded to DAC register −0.10 ± 1.0 %FSR (max) −20 µV/˚C VA = 3V −0.7 ppm/˚C VA = 5V −1.0 ppm/˚C ZCED TC GE Zero Code Error Drift Gain Error Tempco OUTPUT CHARACTERISTICS Output Voltage Range ZCO FSO Zero Code Output Full Scale Output Maximum Load Capacitance 0 VA (Note 10) V (min) V (max) VA = 3V, IOUT = 10 µA 1.8 mV VA = 3V, IOUT = 100 µA 5.0 mV VA = 5V, IOUT = 10 µA 3.7 mV VA = 5V, IOUT = 100 µA 5.4 mV VA = 3V, IOUT = 10 µA 2.997 V VA = 3V, IOUT = 100 µA 2.990 V VA = 5V, IOUT = 10 µA 4.995 V VA = 5V, IOUT = 100 µA RL = ∞ 4.992 V 1500 pF RL = 2kΩ 1500 pF 1.3 Ohm DC Output Impedance 3 www.national.com DAC101S101 Absolute Maximum Ratings DAC101S101 Electrical Characteristics (Continued) Values shown in this table are design targets and are subject to change before product release. The following specifications apply for VA = +2.7V to +5.5V, RL = 2kΩ to GND, CL = 200 pF to GND, fSCLK = 30 MHz, input code range 12 to 1011. Boldface limits apply for TMIN ≤ TA ≤ TMAX: all other limits TA = 25˚C, unless otherwise specified. Symbol IOS Parameter Output Short Circuit Current Typical (Note 9) Conditions Limits (Note 9) Units (Limits) VA = 5V, VOUT = 0V, Input code = 3FFh −63 mA VA = 3V, VOUT = 0V, Input code = 3FFh −50 mA VA = 5V, VOUT = 5V, Input code = 000h 74 mA VA = 3V, VOUT = 3V, Input code = 000h 53 mA LOGIC INPUT IIN Input Current (Note 10) VIL Input Low Voltage (Note 10) VIH Input High Voltage (Note 10) CIN Input Capacitance (Note 10) ±1 µA (max) VA = 5V 0.8 V (max) VA = 3V 0.5 V (max) VA = 5V 2.4 V (min) VA = 3V 2.1 V (min) 3 pF (max) POWER REQUIREMENTS Normal Mode fSCLK = 30 MHz IA Supply Current (output unloaded) www.national.com VA = 3.6V 226 µA (max) 221 297 µA (max) VA = 3.6V 154 207 µA (max) Normal Mode fSCLK = 0 VA = 5.5V 145 µA (max) VA = 3.6V 113 µA (max) VA = 5.0V 83 µA (max) VA = 3.0V 42 µA (max) VA = 5.0V 56 µA (max) VA = 3.0V 28 VA = 5.5V 0.06 VA = 3.6V All PD Modes, fSCLK = 30 MHz µA (max) 1.0 µA (max) 0.04 1.0 µA (max) Normal Mode fSCLK = 30 MHz VA = 5.5V 1.41 1.83 mW (max) VA = 3.6V 0.63 0.81 mW (max) Normal Mode fSCLK = 20 MHz VA = 5.5V 1.22 1.63 mW (max) VA = 3.6V 0.55 0.74 mW (max) Normal Mode fSCLK = 0 VA = 5.5V 0.80 µW (max) VA = 3.6V 0.41 µW (max) All PD Modes, fSCLK = 30 MHz VA = 5.0V 0.42 µW (max) VA = 3.0V 0.13 µW (max) VA = 5.0V 0.28 µW (max) VA = 3.0V 0.08 VA = 5.5V 0.33 5.5 µW (max) VA = 3.6V 0.14 3.6 µW (max) All PD Modes, fSCLK = 0 (Note 10) Power Efficiency µA (max) 174 All PD Modes, fSCLK = 20 MHz IOUT / IA 332 VA = 5.5V All PD Modes, fSCLK = 0 (Note 10) Power Consumption (output unloaded) 256 Normal Mode fSCLK = 20 MHz All PD Modes, fSCLK = 20 MHz PC VA = 5.5V ILOAD = 2mA 4 µW (max) VA = 5V 91 % VA = 3V 94 % Values shown in this table are design targets and are subject to change before product release. The following specifications apply for VA = +2.7V to +5.5V, RL = 2kΩ to GND, CL = 200 pF to GND, fSCLK = 30 MHz, input code range 12 to 1011. Boldface limits apply for TMIN ≤ TA ≤ TMAX: all other limits TA = 25˚C, unless otherwise specified. Symbol Parameter fSCLK SCLK Frequency ts Output Voltage Settling Time (Note 10) SR Output Slew Rate Glitch Impulse Conductions 100h to 300h code change, RL = 2kΩ CL ≤ 200 pF Wake-Up Time 1/fSCLK SCLK Cycle Time tH SCLK High time tL SCLK Low Time 5 Limits Units (Limits) 30 MHz (max) 7.5 µs (max) 1 V/µs 12 nV-sec 0.5 nV-sec VA = 5V 1.6 µs VA = 3V 1.9 Code change from 200h to 1FFh Digital Feedthrough tWU Typical µs 33 ns (min) 5 13 ns (min) 5 13 ns (min) tSUCL Set-up Time SYNC to SCLK Rising Edge −15 0 ns (min) tSUD Data Set-Up Time 2.5 5 ns (min) tDHD Data Hold Time 2.5 4.5 ns (min) VA = 5V 0 3 ns (min) VA = 3V −2 1 ns (min) 2.7 ≤ VA ≤ 3.6 9 20 ns (min) 3.6 ≤ VA ≤ 5.5 5 10 ns (min) tCS SCLK fall to rise of SYNC tSYNC SYNC High Time Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: All voltages are measured with respect to GND = 0V, unless otherwise specified Note 3: When the input voltage at any pin exceeds the power supplies (that is, less than GND, or greater than VA), the current at that pin should be limited to 10 mA. The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 10 mA to two. Note 4: The absolute maximum junction temperature (TJmax) for this device is 150˚C. The maximum allowable power dissipation is dictated by TJmax, the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula PDMAX = (TJmax − TA) / θJA. The values for maximum power dissipation will be reached only when the device is operated in a severe fault condition (e.g., when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided. Note 5: Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through ZERO Ohms. Note 6: See the section entitled "Surface Mount" found in any post 1986 National Semiconductor Linear Data Book for methods of soldering surface mount devices. Note 7: The analog inputs are protected as shown below. Input voltage magnitudes up to VA + 300 mV or to 300 mV below GND will not damage this device. However, errors in the conversion result can occur if any input goes above VA or below GND by more than 100 mV. For example, if VA is 2.7VDC, ensure that −100mV ≤ input voltages ≤2.8VDC to ensure accurate conversions. 20154104 Note 8: To guarantee accuracy, it is required that VA be well bypassed. Note 9: Typical figures are at TJ = 25˚C, and represent most likely parametric norms. Test limits are guaranteed to National’s AOQL (Average Outgoing Quality Level). Note 10: This parameter is guaranteed by design and/or characterization and is not tested in production. 5 www.national.com DAC101S101 A.C. and Timing Characteristics DAC101S101 LSB = VREF / 2n where VREF is the supply voltage for this product, and "n" is the DAC resolution in bits, which is 10 for the DAC101S101. Specification Definitions DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1 LSB, which is VREF / 1024 = VA / 1024. MAXIMUM LOAD CAPACITANCE is the maximum capacitance that can be driven by the DAC with output stability maintained. DIGITAL FEEDTHROUGH is a measure of the energy injected into the analog output of the DAC from the digital inputs when the DAC outputs are not updated. It is measured with a full-scale code change on the data bus. MONOTONICITY is the condition of being monotonic, where the DAC has an output that never decreases when the input code increases. FULL-SCALE ERROR is the difference between the actual output voltage with a full scale code (3FFh) loaded into the DAC and the value of VA x 1023 / 1024. GAIN ERROR is the deviation from the ideal slope of the transfer function. It can be calculated from Zero and FullScale Errors as GE = FSE - ZE, where GE is Gain error, FSE is Full-Scale Error and ZE is Zero Error. MOST SIGNIFICANT BIT (MSB) is the bit that has the largest value or weight of all bits in a word. Its value is 1/2 of V A. POWER EFFICIENCY is the ratio of the output current to the total supply current. The output current comes from the power supply. The difference between the supply and output currents, is the power consumed by the device without a load. GLITCH IMPULSE is the energy injected into the analog output when the input code to the DAC register changes. It is specified as the area of the glitch in nanovolt-seconds. SETTLING TIME is the time for the output to settle within 1/2 LSB of the final value after the input code is updated. INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a straight line through the input to output transfer function. The deviation of any given code from this straight line is measured from the center of that code value. The end point method is used. INL for this product is specified over a limited range, per the Electrical Tables. LEAST SIGNIFICANT BIT (LSB) is the bit that has the smallest value or weight of all bits in a word. This value is www.national.com WAKE-UP TIME is the time for the output to settle to within 1/2 LSB of the final value after the device is commanded to the active mode from any of the power down modes. ZERO CODE ERROR is the output error, or voltage, present at the DAC output after a code of 000h has been entered. 6 DAC101S101 Transfer Characteristic 20154105 FIGURE 1. Input / Output Transfer Characteristic Timing Diagram 20154106 FIGURE 2. DAC101S101 Timing 7 www.national.com DAC101S101 Typical Performance Characteristics fSCLK = 30 MHz, TA = 25C, Input Code Range 12 to 1011, unless otherwise stated DNL at VA = 3.0V DNL at VA = 5.0V 20154152 20154153 INL at VA = 3.0V INL at VA = 5.0V 20154154 20154155 TUE at VA = 3.0V TUE at VA = 5.0V 20154156 www.national.com 20154157 8 DNL vs. VA INL vs. VA 20154122 20154123 3V DNL vs. fSCLK 5V DNL vs. fSCLK 20154150 20154151 3V DNL vs. Clock Duty Cycle 5V DNL vs. Clock Duty Cycle 20154124 20154125 9 www.national.com DAC101S101 Typical Performance Characteristics fSCLK = 30 MHz, TA = 25C, Input Code Range 12 to 1011, unless otherwise stated (Continued) DAC101S101 Typical Performance Characteristics fSCLK = 30 MHz, TA = 25C, Input Code Range 12 to 1011, unless otherwise stated (Continued) 3V DNL vs. Temperature 5V DNL vs. Temperature 20154126 20154127 3V INL vs. fSCLK 5V INL vs. fSCLK 20154128 20154129 3V INL vs. Clock Duty Cycle 5V INL vs. Clock Duty Cycle 20154130 www.national.com 20154131 10 3V INL vs. Temperature 5V INL vs. Temperature 20154132 20154133 Zero Code Error vs. fSCLK Zero Code Error vs. Clock Duty Cycle 20154134 20154135 Zero Code Error vs. Temperature Full-Scale Error vs. fSCLK 20154136 20154137 11 www.national.com DAC101S101 Typical Performance Characteristics fSCLK = 30 MHz, TA = 25C, Input Code Range 12 to 1011, unless otherwise stated (Continued) DAC101S101 Typical Performance Characteristics fSCLK = 30 MHz, TA = 25C, Input Code Range 12 to 1011, unless otherwise stated (Continued) Full-Scale Error vs. Clock Duty Cycle Full-Scale Error vs. Temperature 20154138 20154139 Supply Current vs. VA Supply Current vs. Temperature 20154144 20154145 5V Glitch Response Power-On Reset 20154146 www.national.com 20154147 12 3V Wake-Up Time 5V Wake-Up Time 20154148 20154149 13 www.national.com DAC101S101 Typical Performance Characteristics fSCLK = 30 MHz, TA = 25C, Input Code Range 12 to 1011, unless otherwise stated (Continued) DAC101S101 brought high. In either case, it must be brought high for the minimum specified time before the next write sequence as a falling edge of SYNC is used to initiate the next write cycle. Since the SYNC and DIN buffers draw more current when they are high, they should be idled low between write sequences to minimize power consumption. 1.0 Functional Description 1.1 DAC SECTION The DAC101S101 is fabricated on a CMOS process with an architecture that consists of switches and a resistor string that are followed by an output buffer. The power supply serves as the reference voltage. The input coding is straight binary with an ideal output voltage of: VOUT = VA x (D / 1024) 1.5 INPUT SHIFT REGISTER The input shift register, Figure 4, has sixteen bits. The first two bits are "don’t cares" and are followed by two bits that determine the mode of operation (normal mode or one of three power-down modes). The contents of the serial input register are transferred to the DAC register on the sixteenth falling edge of SCLK. See Timing Diagram, Figure 2. where D is the decimal equivalent of the binary code that is loaded into the DAC register and can take on any value between 0 and 1023. 1.2 RESISTOR STRING The resistor string is shown in Figure 3. This string consists of 4096 equal valued resistors with a switch at each junction of two resistors, plus a switch to ground. The code loaded into the DAC register determines which switch is closed, connecting the proper node to the amplifier. This configuration guarantees that the DAC is monotonic. 20154108 FIGURE 4. Input Register Contents Normally, the SYNC line is kept low for at least 16 falling edges of SCLK and the DAC is updated on the 16th SCLK falling edge. However, if SYNC is brought high before the 16th falling edge, the shift register is reset and the write sequence is invalid. The DAC register is not updated and there is no change in the mode of operation or in the output voltage. 1.6 POWER-ON RESET The power-on reset circuit controls the output voltage during power-up. Upon application of power the DAC register is filled with zeros and the output voltage is 0 Volts and remains there until a valid write sequence is made to the DAC. 1.7 POWER-DOWN MODES The DAC101S101 has four modes of operation. These modes are set with two bits (DB13 and DB12) in the control register. 20154107 FIGURE 3. DAC Resistor String TABLE 1. Modes of Operation 1.3 OUTPUT AMPLIFIER The output buffer amplifier is a rail-to-rail type, providing an output voltage range of 0V to VA. All amplifiers, even rail-torail types, exhibit a loss of linearity as the output approaches the supply rails (0V and VA, in this case). For this reason, linearity is specified over less than the full output range of the DAC. The output capabilities of the amplifier are described in the Electrical Tables. DB12 0 0 Operating Mode Normal Operation 0 1 Power-Down with 1kΩ to GND 1 0 Power-Down with 100kΩ to GND 1 1 Power-Down with Hi-Z When both DB13 and DB12 are 0, the device operates normally. For the other three possible combinations of these bits the supply current drops to its power-down level and the output is pulled down with either a 1kΩ or a 100KΩ resistor, or is in a high impedance state, as described in Table 1. The bias generator, output amplifier, the resistor string and other linear circuitry are all shut down in any of the powerdown modes. However, the contents of the DAC register are unaffected when in power-down, so when coming out of power down the output voltage returns to the same voltage it 1.4 SERIAL INTERFACE The three-wire interface is compatible with SPI, QSPI and MICROWIRE as well as most DSPs. See the Timing Diagram for information on a write sequence. A write sequence begins by bringing the SYNC line low. Once SYNC is low, the data on the DIN line is clocked into the 16-bit serial input register on the falling edges of SCLK. On the 16th falling clock edge, the last data bit is clocked in and the programmed function (a change in the mode of operation and/or a change in the DAC register contents) is executed. At this point the SYNC line may be kept low or www.national.com DB13 14 2.1.3 68HC11 Interface (Continued) A serial interface between the DAC101S101 and the 68HC11 microcontroller is shown in Figure 7. The SYNC line of the DAC101S101 is driven from a port line (PC7 in the figure), similar to the 80C51/80L51. was before entering power down. Minimum power consumption is achieved in the power-down mode with SCLK disabled and SYNC and DIN idled low. The 68HC11 should be configured with its CPOL bit as a zero and its CPHA bit as a one. This configuration causes data on the MOSI output to be valid on the falling edge of SCLK. PC7 is taken low to transmit data to the DAC. The 68HC11 transmits data in 8-bit bytes with eight falling clock edges. Data is transmitted with the MSB first. PC7 must remain low after the first eight bits are transferred. A second write cycle is initiated to transmit the second byte of data to the DAC, after which PC7 should be raised to end the write sequence. 2.0 Applications Information The simplicity of the DAC101S101 implies ease of use. However, it is important to recognize that any data converter that utilizes its supply voltage as its reference voltage will have essentially zero PSRR (Power Supply Rejection Ratio). Therefore, it is necessary to provide a noise-free supply voltage to the device. 2.1 DSP/MICROPROCESSOR INTERFACING Interfacing the DAC101S101 to microprocessors and DSPs is quite simple. The following guidelines are offered to hasten the design process. 2.1.1 ADSP-2101/ADSP2103 Interfacing Figure 5 shows a serial interface between the DAC101S101 and the ADSP-2101/ADSP2103. The DSP should be set to operate in the SPORT Transmit Alternate Framing Mode. It is programmed through the SPORT control register and should be configured for Internal Clock Operation, Active Low Framing and 16-bit Word Length. Transmission is started by writing a word to the Tx register after the SPORT mode has been enabled. 20154111 FIGURE 7. 68HC11 Interface 2.1.4 Microwire Interface Figure 8 shows an interface between a Microwire compatible device and the DAC101S101. Data is clocked out on the rising edges of the SCLK signal. 20154109 20154112 FIGURE 5. ADSP-2101/2103 Interface FIGURE 8. Microwire Interface 2.1.2 80C51/80L51 Interface A serial interface between the DAC101S101 and the 80C51/ 80L51 microcontroller is shown in Figure 6. The SYNC signal comes from a bit-programmable pin on the microcontroller. The example shown here uses port line P3.3. This line is taken low when data is to transmitted to the DAC101S101. Since the 80C51/80L51 transmits 8-bit bytes, only eight falling clock edges occur in the transmit cycle. To load data into the DAC, the P3.3 line must be left low after the first eight bits are transmitted. A second write cycle is initiated to transmit the second byte of data, after which port line P3.3 is brought high. The 80C51/80L51 transmit routine must recognize that the 80C51/80L51 transmits data with the LSB first while the DAC101S101 requires data with the MSB first. 2.2 USING REFERENCES AS POWER SUPPLIES Recall the need for a quiet supply source for devices that use their power supply voltage as a reference voltage. Since the DAC101S101 consumes very little power, a reference source may be used as the supply voltage. The advantages of using a reference source over a voltage regulator are accuracy and stability. Some low noise regulators can also be used for the power supply of the DAC101S101. Listed below are a few power supply options for the DAC101S101. 2.2.1 LM4130 The LM4130 reference, with its 0.05% accuracy over temperature, is a good choice as a power source for the DAC101S101. Its primary disadvantage is the lack of 3V and 5V versions. However, the 4.096V version is useful if a 0 to 4.095V output range is desirable or acceptable. Bypassing the LM4130 VIN pin with a 0.1µF capacitor and the VOUT pin with a 2.2µF capacitor will improve stability and reduce output noise. The LM4130 comes in a space-saving 5-pin SOT23. 20154110 FIGURE 6. 80C51/80L51 Interface 15 www.national.com DAC101S101 1.0 Functional Description DAC101S101 2.0 Applications Information LM4050 for proper regulation, IA(max) is the maximum DAC101S101 supply current, and IA(min) is the minimum DAC101S101 supply current. (Continued) 2.2.3 LP3985 The LP3985 is a low noise, ultra low dropout voltage regulator with a 3% accuracy over temperature. It is a good choice for applications that do not require a precision reference for the DAC101S101. It comes in 3.0V, 3.3V and 5V versions, among others, and sports a low 30 µV noise specification at low frequencies. Since low frequency noise is relatively difficult to filter, this specification could be important for some applications. The LP3985 comes in a space-saving 5-pin SOT23 and 5-bump micro SMD packages. 20154113 FIGURE 9. The LM4130 as a power supply 2.2.2 LM4050 Available with accuracy of 0.44%, the LM4050 shunt reference is also a good choice as a power regulator for the DAC101S101. It does not come in a 3 Volt version, but 4.096V and 5V versions are available. It comes in a spacesaving 3-pin SOT23. 20154115 FIGURE 11. Using the LP3985 regulator An input capacitance of 1.0µF without any ESR requirement is required at the LP3985 input, while a 1.0µF ceramic capacitor with an ESR requirement of 5mΩ to 500mΩ is required at the output. Careful interpretation and understanding of the capacitor specification is required to ensure correct device operation. 2.2.4 LP2980 The LP2980 is an ultra low dropout regulator with a 0.5% or 1.0% accuracy over temperature, depending upon grade. It is available in 3.0V, 3.3V and 5V versions, among others. 20154114 FIGURE 10. The LM4050 as a power supply The minimum resistor value in the circuit of Figure 10 should be chosen such that the maximum current through the LM4050 does not exceed its 15 mA rating. The conditions for maximum current include the input voltage at its maximum, the LM4050 voltage at its minimum, the resistor value at its minimum due to tolerance, and the DAC101S101 draws zero current. The maximum resistor value must allow the LM4050 to draw more than its minimum current for regulation plus the maximum DAC101S101 current in full operation. The conditions for minimum current include the input voltage at its minimum, the LM4050 voltage at its maximum, the resistor value at its maximum due to tolerance, and the DAC101S101 draws its maximum current. These conditions can be summarized as R(min) = ( VIN(max) − VZ(min) / (IA(min) + IZ(max)) and R(max) = ( VIN(min) − VZ(max) / (IA(max) + IZ(min) ) where VZ(min) and VZ(max) are the nominal LM4050 output voltages ± the LM4050 output tolerance over temperature, IZ(max) is the maximum allowable current through the LM4050, IZ(min) is the minimum current required by the www.national.com 20154116 FIGURE 12. Using the LP2980 regulator Like any low dropout regulator, the LP2980 requires an output capacitor for loop stability. This output capacitor must be at least 1.0µF over temperature, but values of 2.2µF or more will provide even better performance. The ESR of this capacitor should be within the range specified in the LP2980 data sheet. Surface-mount solid tantalum capacitors offer a good combination of small size and ESR. Ceramic capacitors are attractive due to their small size but generally have ESR values that are too low for use with the LP2980. Alumi- 16 2.4 LAYOUT, GROUNDING, AND BYPASSING For best accuracy and minimum noise, the printed circuit board containing the DAC101S101 should have separate analog and digital areas. The areas are defined by the locations of the analog and digital power planes. Both of these planes should be located in the same board layer. There should be a single ground plane. A single ground plane is preferred if digital return current does not flow through the analog ground area. Frequently a single ground plane design will utilize a "fencing" technique to prevent the mixing of analog and digital ground current. Separate ground planes should only be utilized when the fencing technique is inadequate. The separate ground planes must be connected in one place, preferably near the DAC101S101. Special care is required to guarantee that digital signals with fast edge rates do not pass over split ground planes. They must always have a continuous return path below their traces. (Continued) num electrolytic capacitors are typically not a good choice due to their large size and have ESR values that may be too high at low temperatures. 2.3 BIPOLAR OPERATION The DAC101S101 is designed for single supply operation and thus has a unipolar output. However, a bipolar output may be obtained with the circuit in Figure 13. This circuit will provide an output voltage range of ± 5 Volts. A rail-to-rail amplifier should be used if the amplifier supplies are limited to ± 5V. The DAC101S101 power supply should be bypassed with a 10µF and a 0.1µF capacitor as close as possible to the device with the 0.1µF right at the device supply pin. The 10µF capacitor should be a tantalum type and the 0.1µF capacitor should be a low ESL, low ESR type. The power supply for the DAC101S101 should only be used for analog circuits. Avoid crossover of analog and digital signals and keep the clock and data lines on the component side of the board. The clock and data lines should have controlled impedances. 20154117 FIGURE 13. Bipolar Operation The output voltage of this circuit for any code is found to be VO = (VA x (D / 1024) x ((R1 + R2) / R1) - VA x R2 / R1) where D is the input code in decimal form. With VA = 5V and R1 = R2, VO = (10 x D / 1024) - 5V A list of rail-to-rail amplifiers suitable for this application are indicated in Table 2. TABLE 2. Some Rail-to-Rail Amplifiers AMP PKGS LMC7111 DIP-8 SOT23-5 Typ VOS Typ ISUPPLY 0.9 mV 25 µA LM7301 SO-8 SOT23-5 0.03 mV 620 µA LM8261 SOT23-5 0.7 mV 1 mA 17 www.national.com DAC101S101 2.0 Applications Information DAC101S101 Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead MSOP Order Numbers DAC101S101CIMM NS Package Number MUA08A 6-Lead TSOT Order Numbers DAC101S101CIMK NS Package Number MK06A www.national.com 18 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 DAC101S101 10-Bit Micro Power Digital-to-Analog Converter with Rail-to-Rail Output Notes