Data Sheet 2.7 V to 5.5 V, 140 µA, Rail-to-Rail Voltage Output 10-Bit DAC in a SOT-23 AD5310 FEATURES FUNCTIONAL BLOCK DIAGRAM Single 10-bit DAC 6-lead SOT-23 and 8-lead µSOIC packages Micropower operation: 140 µA @ 5 V Power-down to 200 nA @ 5 V, 50 nA @ 3 V 2.7 V to 5.5 V power supply Guaranteed monotonic by design Reference derived from power supply Power-on reset to 0 V Three power-down functions Low power serial interface with Schmitt triggered inputs On-chip output buffer amplifier, rail-to-rail operation SYNC interrupt facility Qualified for automotive applications APPLICATIONS Figure 1. Portable battery-powered instruments Digital gain and offset adjustment Programmable voltage and current sources Programmable attenuators GENERAL DESCRIPTION The AD53101 is a single, 10-bit, buffered voltage output DAC that operates from a single 2.7 V to 5.5 V supply, consuming 115 µA at 3 V. Its on-chip precision output amplifier allows rail-to-rail output swing. The AD5310 utilizes a versatile 3-wire serial interface that operates at clock rates of up to 30 MHz and is compatible with standard SPI™, QSPI™, MICROWIRE®, and DSP interface standards. The reference for AD5310 is derived from the power supply inputs and, therefore, provides the widest dynamic output range. The part incorporates a power-on reset circuit that ensures that the DAC output powers up to 0 V and remains there until a valid write takes place to the device. The part contains a power-down feature, which reduces the current consumption of the device to 200 nA at 5 V and provides software-selectable output loads while in power-down mode. The part is put into power-down mode over the serial interface. The low power consumption of this part in normal operation makes it ideally suited for portable, battery-operated equipment. The power consumption is 0.7 mW at 5 V, reducing to 1 µW in power-down mode. 1 The AD5310 is one of a family of pin-compatible DACs. The AD5300 is the 8-bit version, and the AD5320 is the 12-bit version. The AD5300/AD5310/AD5320 are available in 6-lead SOT-23 packages and 8-lead µSOIC packages. PRODUCT HIGHLIGHTS 1. 2. 3. 4. 5. 6. Available in 6-lead SOT-23 and 8-lead µSOIC packages. Low power, single-supply operation. This part operates from a single 2.7 V to 5.5 V supply and typically consumes 0.35 mW at 3 V and 0.7 mW at 5 V, making it ideal for battery-powered applications. The on-chip output buffer amplifier allows the output of the DAC to swing rail-to-rail with a slew rate of 1 V/µs. Reference derived from the power supply. High speed serial interface with clock speeds of up to 30 MHz. Designed for very low power consumption. The interface only powers up during a write cycle. Power-down capability. When powered down, the DAC typically consumes 50 nA at 3 V and 200 nA at 5 V. Patent pending; protected by U.S. Patent No. 5684481. Rev. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2012 Analog Devices, Inc. All rights reserved. AD5310 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Output Amplifier ........................................................................ 11 Applications ....................................................................................... 1 Serial Interface ............................................................................ 11 Functional Block Diagram .............................................................. 1 Input Shift Register .................................................................... 11 General Description ......................................................................... 1 SYNC Interrupt .......................................................................... 12 Product Highlights ........................................................................... 1 Power-On Reset .......................................................................... 12 Revision History ............................................................................... 2 Power-Down Modes .................................................................. 12 Specifications..................................................................................... 3 Microprocessor Interfacing ....................................................... 12 Timing Characteristics ................................................................ 4 Applications Information .............................................................. 14 Absolute Maximum Ratings ............................................................ 5 Using REF19x as a Power Supply for AD5310 ....................... 14 ESD Caution .................................................................................. 5 Bipolar Operation Using the AD5310 ..................................... 14 Pin Configurations and Function Descriptions ........................... 6 Using AD5310 with an Opto-Isolated Interface .................... 14 Typical Performance Characteristics ............................................. 7 Power Supply Bypassing and Grounding ................................ 15 Terminology .................................................................................... 10 Outline Dimensions ....................................................................... 16 Theory of Operation ...................................................................... 11 Ordering Guide .......................................................................... 16 D/A Section ................................................................................. 11 Automotive Products ................................................................. 16 Resistor String ............................................................................. 11 REVISION HISTORY 7/12—Rev. A to Rev. B Updated Format .................................................................. Universal Changes to Features.......................................................................... 1 Change to Figure 9 Caption ............................................................ 7 Changes to AD5310 to ADSP-2101 Interface Section and Figure 27............................................................................... 12 Updated Outline Dimensions ....................................................... 16 Changes to Ordering Guide .......................................................... 16 Added Automotive Products Section........................................... 16 5/99—Rev. 0 to Rev. A Rev. B | Page 2 of 16 Data Sheet AD5310 SPECIFICATIONS VDD = 2.7 V to 5.5 V; temperature range = −40°C to +105°C RL = 2 kΩ to GND; CL = 500 pF to GND; all specifications TMIN to TMAX unless otherwise noted Table 1. Parameter STATIC PERFORMANCE 1 Resolution Relative Accuracy Differential Nonlinearity Zero Code Error Full-Scale Error Gain Error Zero Code Error Drift Gain Temperature Coefficient OUTPUT CHARACTERISTICS 2 Output Voltage Range Output Voltage Settling Time Slew Rate Capacitive Load Stability Min 5 −0.15 2 ±4 ±0.5 40 −1.25 ±1.25 −20 −5 0 6 1 470 1000 20 0.5 1 50 20 2.5 5 Power-Up Time 1 Max 10 Digital-to-Analog Glitch Impulse Digital Feedthrough DC Output Impedance Short-Circuit Current LOGIC INPUTS2 Input Current VINL, Input Low Voltage VINL, Input Low Voltage VINH, Input High Voltage VINH, Input High Voltage Pin Capacitance POWER REQUIREMENTS VDD IDD (Normal Mode) VDD = 4.5 V to 5.5 V VDD = 2.7 V to 3.6 V IDD (All Power-Down Modes) VDD = 4.5 V to 5.5 V VDD = 2.7 V to 3.6 V Power Efficiency IOUT/IDD Typ VDD 8 ±1 0.8 0.6 Unit Bits LSB LSB mV % of FSR % of FSR µV/°C ppm of FSR/°C V µs V/µs pF pF nV-s nV-s Ω mA mA µs µs Test Conditions/Comments See Figure 5 Guaranteed monotonic by design (see Figure 6) All 0s loaded to DAC register (see Figure 9) All 1s loaded to DAC register (see Figure 9) ¼ scale to ¾ scale change (100 hex to 300 hex) RL = 2 kΩ; 0 pF < CL < 500 pF (see Figure 19) RL = ∞ RL = 2 kΩ 1 LSB change around major carry (see Figure 22) VDD = 5 V VDD = 3 V Coming out of power-down mode, VDD = 5 V Coming out of power-down mode, VDD = 3 V 3 µA V V V V pF 5.5 V 140 115 250 200 µA µA DAC active and excluding load current VIH = VDD and VIL = GND VIH = VDD and VIL = GND 0.2 0.05 1 1 µA µA VIH = VDD and VIL = GND VIH = VDD and VIL = GND % ILOAD = 2 mA, VDD = 5 V 2.4 2.1 2.7 93 Linearity calculated using a reduced code range of 12 to 1011. Output unloaded. Guaranteed by design and characterization; not production tested. Rev. B | Page 3 of 16 VDD = 5 V VDD = 3 V VDD = 5 V VDD = 3 V AD5310 Data Sheet TIMING CHARACTERISTICS VDD = 2.7 V to 5.5 V; all specifications TMIN to TMAX unless otherwise noted Table 2. Parameter 1, 2 t1 3 t2 t3 t4 t5 t6 t7 t8 VDD = 2.7 V to 3.6 V 50 13 22.5 0 5 4.5 0 50 Limit at TMIN, TMAX VDD = 3.6 V to 5.5 V 33 13 13 0 5 4.5 0 33 Unit ns min ns min ns min ns min ns min ns min ns min ns min All input signals are specified with tr = tf = 5 ns (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2. See Figure 2. 3 Maximum SCLK frequency is 30 MHz at VDD = 3.6 V to 5.5 V and 20 MHz at VDD = 2.7 V to 3.6 V. 1 2 Figure 2. Serial Write Operation Rev. B | Page 4 of 16 Test Conditions/Comments SCLK cycle time SCLK high time SCLK low time SYNC to SCLK rising edge setup time Data setup time Data hold time SCLK falling edge to SYNC rising edge Minimum SYNC high time Data Sheet AD5310 ABSOLUTE MAXIMUM RATINGS TA = 25°C unless otherwise noted Table 3. Parameter VDD to GND Digital Input Voltage to GND VOUT to GND Operating Temperature Range Industrial (B Version) Storage Temperature Range Junction Temperature (TJ Max) SOT-23 Package Power Dissipation θJA Thermal Impedance Lead Temperature, Soldering Vapor Phase (60 sec) Infrared (15 sec) µSOIC Package Power Dissipation θJA Thermal Impedance θJC Thermal Impedance Lead Temperature, Soldering Vapor Phase (60 sec) Infrared (15 sec) Rating −0.3 V to +7 V −0.3 V to VDD + 0.3 V −0.3 V to VDD + 0.3 V −40°C to +105°C −65°C to +150°C +150°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION (TJ max − TA)/θJA 240°C/W 215°C 220°C (TJ max − TA)/θJA 206°C/W 44°C/W 215°C 220°C Rev. B | Page 5 of 16 AD5310 Data Sheet PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS Figure 4. µSOIC Figure 3. SOT-23 Table 4. SOT-23 Pin Function Descriptions Pin No. 1 2 3 4 Mnemonic VOUT GND VDD DIN 5 SCLK 6 SYNC Description Analog Output Voltage from DAC. The output amplifier has rail-to-rail operation. Ground Reference Point for All Circuitry on the Part. Power Supply Input. These parts can be operated from 2.5 V to 5.5 V, and VDD should be decoupled to GND. Serial Data Input. This device has a 16-bit shift register. Data is clocked into the register on the falling edge of the serial clock input. Serial Clock Input. Data is clocked into the input shift register on the falling edge of the serial clock input. Data can be transferred at rates of up to 30 MHz. Level Triggered Control Input (Active Low). This is the frame synchronization signal for the input data. When SYNC goes low, it enables the input shift register, and data is transferred in on the falling edges of the following clocks. The DAC is updated following the 16th clock cycle unless SYNC is taken high before this edge, in which case the rising edge of SYNC acts as an interrupt and the write sequence is ignored by the DAC. Rev. B | Page 6 of 16 Data Sheet AD5310 TYPICAL PERFORMANCE CHARACTERISTICS Figure 5. Typical INL Figure 8. INL Error and DNL Error vs. Temperature Figure 6. Typical DNL Figure 9. Zero Code Error and Full-Scale Error vs. Temperature Figure 7. Typical Total Unadjusted Error Figure 10. IDD Histogram with VDD = 3 V and VDD = 5 V Rev. B | Page 7 of 16 AD5310 Data Sheet Figure 11. Source and Sink Current Capability with VDD = 3 V Figure 14. Supply Current vs. Temperature Figure 12. Source and Sink Current Capability with VDD = 5 V Figure 15. Supply Current vs. Supply Voltage Figure 13. Supply Current vs. Code Figure 16. Power-Down Current vs. Supply Voltage Rev. B | Page 8 of 16 Data Sheet AD5310 Figure 17. Supply Current vs. Logic Input Voltage Figure 20. Power-On Reset to 0 V Figure 18. Full-Scale Settling Time Figure 21. Exiting Power-Down (200 Hex Loaded) Figure 19. Half-Scale Settling Time Figure 22. Digital-to-Analog Glitch Impulse Rev. B | Page 9 of 16 AD5310 Data Sheet TERMINOLOGY Relative Accuracy For the DAC, relative accuracy or integral nonlinearity (INL) is a measure of the maximum deviation, in LSBs, from a straight line passing through the endpoints of the DAC transfer function. A typical INL vs. code plot is shown in Figure 5. Differential Nonlinearity Differential nonlinearity (DNL) is the difference between the measured change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of ±1 LSB maximum ensures monotonicity. This DAC is guaranteed monotonic by design. A typical DNL vs. code plot is shown in Figure 6. Zero Code Error Zero code error is a measure of the output error when zero code (000 hex) is loaded to the DAC register. Ideally, the output should be 0 V. The zero code error is always positive in the AD5310 because the output of the DAC cannot go below 0 V. It is due to a combination of the offset errors in the DAC and output amplifier. Zero code error is expressed in mV. A plot of zero code error vs. temperature is shown in Figure 9. Full-Scale Error Full-scale error is a measure of the output error when full-scale code (3FF Hex) is loaded to the DAC register. Ideally, the output should be VDD − 1 LSB. Full-scale error is expressed as a percentage of the full-scale range. A plot of full-scale error vs. temperature is shown in Figure 9. Gain Error Gain error is a measure of the span error of the DAC. It is the deviation in slope of the DAC transfer characteristic from the ideal expressed as a percentage of the full-scale range. Total Unadjusted Error Total unadjusted error (TUE) is a measure of the output error that takes all the various errors into account. A typical TUE vs. code plot is shown in Figure 7. Zero Code Error Drift Zero code error drift is a measure of the change in zero code error with a change in temperature. It is expressed in µV/°C. Gain Error Drift Gain error drift is a measure of the change in gain error with changes in temperature. It is expressed in (ppm of full-scale range)/°C. Digital-to-Analog Glitch Impulse Digital-to-analog glitch impulse is the impulse injected into the analog output when the input code in the DAC register changes state. It is normally specified as the area of the glitch in nV-s and is measured when the digital input code is changed by 1 LSB at the major carry transition (1FF hex to 200 hex). See Figure 22. Digital Feedthrough Digital feedthrough is a measure of the impulse injected into the analog output of the DAC from the digital inputs of the DAC but is measured when the DAC output is not updated. It is specified in nV-s and is measured with a full-scale code change on the data bus, that is, from all 0s to all 1s and vice versa. Rev. B | Page 10 of 16 Data Sheet AD5310 THEORY OF OPERATION D/A SECTION to the amplifier. Because it is a string of resistors, it is guaranteed monotonic. The AD5310 DAC is fabricated on a CMOS process. The architecture consists of a string DAC followed by an output buffer amplifier. Because there is no reference input pin, the power supply (VDD) acts as the reference. Figure 23 shows a block diagram of the DAC architecture. OUTPUT AMPLIFIER The output buffer amplifier is capable of generating rail-to-rail voltages on its output, which results in an output range of 0 V to VDD. It is capable of driving a load of 2 kΩ in parallel with 1000 pF to GND. The source and sink capabilities of the output amplifier can be seen in Figure 11 and Figure 12. The slew rate is 1 V/µs with a half-scale settling time of 6 µs with the output loaded. SERIAL INTERFACE Figure 23. DAC Architecture Because the input coding to the DAC is straight binary, the ideal output voltage is given by VOUT D = VDD × 1024 where D is the decimal equivalent of the binary code that is loaded to the DAC register; it can range from 0 to 1023. The AD5310 has a 3-wire serial interface (SYNC, SCLK, and DIN) that is compatible with SPI, QSPI, and MICROWIRE interface standards, as well as most DSPs. See Figure 2 for a timing diagram of a typical write sequence. The write sequence begins by bringing the SYNC line low. Data from the DIN line is clocked into the 16-bit shift register on the falling edge of SCLK. The serial clock frequency can be as high as 30 MHz, making the AD5310 compatible with high speed DSPs. On the 16th falling clock edge, the last data bit is clocked in and the programmed function is executed (that is, a change in DAC register contents and/or a change in the mode of operation). At this stage, the SYNC line can be kept low or be brought high. In either case, it must be brought high for a minimum of 33 ns before the next write sequence so that a falling edge of SYNC can initiate the next write sequence. Because the SYNC buffer draws more current when VIN = 2.4 V than it does when VIN = 0.8 V, SYNC should be idled low between write sequences for even lower power operation of the part. As previously mentioned, however, it must be brought high again just before the next write sequence. INPUT SHIFT REGISTER Figure 24. Resistor String RESISTOR STRING The resistor string section is shown in Figure 24. It is simply a string of resistors, each of value R. The code loaded to the DAC register determines at what node on the string the voltage is tapped off to be fed into the output amplifier. The voltage is tapped off by closing one of the switches connecting the string The input shift register is 16 bits wide (see Figure 25). The first two bits are don’t cares. The next two bits are control bits that control which mode of operation the part is in (normal mode or one of the three power-down modes). There is a more complete description of the various modes in the Power-Down Modes section. The next 10 bits are the data bits. These are transferred to the DAC register on the 16th falling edge of SCLK. Finally, the last two bits are don’t cares. Figure 25. Input Register Contents Rev. B | Page 11 of 16 AD5310 Data Sheet SYNC INTERRUPT In a normal write sequence, the SYNC line is kept low for at least 16 falling edges of SCLK, and the DAC is updated on the 16th falling edge. However, if SYNC is brought high before the 16th falling edge, this acts as an interrupt to the write sequence. The shift register is reset, and the write sequence is seen as invalid. Neither an update of the DAC register contents or a change in the operating mode occurs (see Figure 28). the part is in power-down mode. There are three options. The output is connected internally to GND through a 1 kΩ resistor, a 100 kΩ resistor, or it is left open-circuited (three-state). The output stage is illustrated in Figure 26. POWER-ON RESET The AD5310 contains a power-on reset circuit that controls the output voltage during power-up. The DAC register is filled with 0s, and the output voltage is 0 V. It remains there until a valid write sequence is performed to the DAC. This is useful in applications where it is important to know the state of the output of the DAC while it is in the process of powering up. POWER-DOWN MODES The AD5310 contains four separate modes of operation. These modes are software programmable by setting two bits (DB13 and DB12) in the control register. Table 5 shows how the state of the bits corresponds to the mode of operation of the device. Table 5. Modes of Operation for the AD5310 Operating Mode Normal Operation Power-Down Modes 1 kΩ to GND 100 kΩ to GND Three-State DB13 0 DB12 0 0 1 1 1 0 1 Figure 26. Output Stage During Power-Down The bias generator, the output amplifier, the resistor string, and other associated linear circuitry are all shut down when the power-down mode is activated. However, the contents of the DAC register are unaffected when in power-down. The time to exit power-down is typically 2.5 µs for VDD = 5 V and 5 µs for VDD = 3 V (see Figure 21). MICROPROCESSOR INTERFACING AD5310 to ADSP-2101 Interface Figure 27 shows a serial interface between the AD5310 and the ADSP-2101. The ADSP-2101 should be set up to operate in the SPORT transmit alternate framing mode. The ADSP-2101SPORT is programmed through the SPORT control register and should be configured as follows: internal clock operation, active low framing, 16-bit word length. Transmission is initiated by writing a word to the Tx register after the SPORT has been enabled. ADSP-2101* When both bits are set to 0, the part works normally with its normal power consumption of 140 µA at 5 V. However, for the three power-down modes, the supply current falls to 200 nA at 5 V (50 nA at 3 V). Not only does the supply current fall, but the output stage is also internally switched from the output of the amplifier to a resistor network of known values. This has the advantage of knowing the output impedance of the part when TFS DT SCLK AD5310* SYNC DIN SCLK *ADDITIONAL PINS OMITTED FOR CLARITY Figure 28. SYNC Interrupt Facility Rev. B | Page 12 of 16 Figure 27. AD5310 to ADSP-2101 Interface Data Sheet AD5310 AD5310 to 68HC11/68L11 Interface Figure 29 shows a serial interface between the AD5310 and the 68HC11/68L11 microcontroller. SCK of the 68HC11/68L11 drives the SCLK of the AD5310, while the MOSI output drives the serial data line of the DAC. The SYNC signal is derived from a port line (PC7). The setup conditions for correct operation of this interface are as follows: the 68HC11/68L11 should be configured so that its CPOL bit is a 0 and its CPHA bit is a 1. When data is being transmitted to the DAC, the SYNC line is taken low (PC7). With this 68HC11/68L11 configuration, data appearing on the MOSI output is valid on the falling edge of SCK. Serial data from the 68HC11/68L11 is transmitted in 8-bit bytes with only eight falling clock edges occurring in the transmit cycle. Data is transmitted MSB first. To load data to the AD5310, PC7 is left low after the first eight bits are transferred, a second serial write operation is performed to the DAC, and PC7 is taken high at the end of this procedure. transmitted to the AD5310, P3.3 is taken low. The 80C51/80L51 transmits data only in 8-bit bytes; therefore, only eight falling clock edges occur in the transmit cycle. To load data to the DAC, P3.3 is left low after the first eight bits are transmitted, and a second write cycle is initiated to transmit the second byte of data. P3.3 is taken high following the completion of this cycle. The 80C51/ 80L51 outputs the serial data in a format that has the LSB first. The AD5310 requires that the MSB of data be received first. The 80C51/80L51 transmit routine should take this into account. Figure 30. AD5310 to 80C51/80L51 Interface AD5310 to MICROWIRE Interface Figure 31 shows an interface between the AD5310 and any MICROWIRE-compatible device. Serial data is shifted out on the falling edge of the serial clock and is clocked into the AD5310 on the rising edge of the SK. Figure 29. AD5310 to 68HC11/68L11 Interface AD5310 to 80C51/80L51 Interface Figure 30 shows a serial interface between the AD5310 and the 80C51/80L51 microcontroller. The setup for the interface is as follows: TXD of the 80C51/80L51 drives SCLK of the AD5310 while RXD drives the serial data line of the part. The SYNC signal is again derived from a bit-programmable pin on the port. In this case, Port Line P3.3 is used. When data is to be Rev. B | Page 13 of 16 Figure 31. AD5310 to MICROWIRE Interface AD5310 Data Sheet APPLICATIONS INFORMATION USING REF19x AS A POWER SUPPLY FOR AD5310 Because the supply current required by the AD5310 is extremely low, an alternative option is to use a REF19x voltage reference (REF195 for 5 V or REF193 for 3 V) to supply the required voltage to the part (see Figure 32). This is especially useful if the power supply is quite noisy or if the system supply voltages are at some value other than 5 V or 3 V (for example, 15 V). The REF19x outputs a steady supply voltage for the AD5310. If the low dropout REF195 is used, the current that it needs to supply to the AD5310 is 140 µA. This is with no load on the output of the DAC. When the DAC output is loaded, the REF195 also needs to supply the current to the load. The total current required (with a 5 kΩ load on the DAC output) is 140 µA + (5 V/5 kΩ) = 1.14 mA The load regulation of the REF195 is typically 2 ppm/mA, which results in an error of 2.3 ppm (11.5 µV) for the 1.14 mA current drawn from it. This corresponds to a 0.002 LSB error. Figure 33. Bipolar Operation with the AD5310 USING AD5310 WITH AN OPTO-ISOLATED INTERFACE In process control applications in industrial environments, it is often necessary to use an opto-isolated interface to protect and isolate the controlling circuitry from any hazardous commonmode voltages that may occur in the area where the DAC is functioning. Opto-isolators provide isolation in excess of 3 kV. Because the AD5310 uses a 3-wire serial logic interface, it only requires three opto-isolators to provide the required isolation (see Figure 34). The power supply to the part also needs to be isolated. This is done by using a transformer. On the DAC side of the transformer, a 5 V regulator provides the 5 V supply required for the AD5310. Figure 32. REF195 as Power Supply to AD5310 BIPOLAR OPERATION USING THE AD5310 The AD5310 is designed for single-supply operation but a bipolar output range is also possible using the circuit shown in Figure 33. This circuit results in an output voltage range of ±5 V. Rail-to-rail operation at the amplifier output is achievable using an AD820 or an OP295 as the output amplifier. The output voltage for any input code can be calculated as follows: D R1 + R2 R2 VO = VDD × × − VDD × 1024 R1 R1 where D represents the input code in decimal (0 to 1023). With VDD = 5 V, R1 = R2 = 10 kΩ, Figure 34. AD5310 with an Opto-Isolated Interface 10 × D VO = −5 V 1024 This is an output voltage range of ±5 V, with 000 hex corresponding to a −5 V output and 3FF hex corresponding to a +5 V output. Rev. B | Page 14 of 16 Data Sheet AD5310 POWER SUPPLY BYPASSING AND GROUNDING When accuracy is important in a circuit, it is helpful to carefully consider the power supply and ground return layout on the board. The printed circuit board containing the AD5310 should have separate analog and digital sections, each having their own area of the board. If the AD5310 is in a system where other devices require an AGND to DGND connection, the connection should be made at one point only. This ground point should be as close as possible to the AD5310. The power supply to the AD5310 should be bypassed with 10 µF and 0.1 µF capacitors. The capacitors should be physically as close as possible to the device, with the 0.1 µF capacitor ideally right up against the device. The 10 µF capacitors are the tantalum bead type. It is important that the 0.1 µF capacitor has low effective series resistance (ESR) and effective series inductance (ESI), such as is the case with common ceramic types of capacitors. This 0.1 µF capacitor provides a low impedance path to ground for high frequencies caused by transient currents due to internal logic switching. The power supply line itself should have as large a trace as possible to provide a low impedance path and to reduce glitch effects on the supply line. Clocks and other fast switching digital signals should be shielded from other parts of the board by digital ground. Avoid crossover of digital and analog signals if possible. When traces cross on opposite sides of the board, ensure that they run at right angles to each other to reduce feedthrough effects through the board. The best board layout technique is the microstrip technique, where the component side of the board is dedicated to the ground plane only and the signal traces are placed on the solder side. However, this is not always possible with a 2-layer board. Rev. B | Page 15 of 16 AD5310 Data Sheet OUTLINE DIMENSIONS 3.20 3.00 2.80 3.00 2.90 2.80 1.70 1.60 1.50 6 5 4 1 2 3 3.00 2.80 2.60 8 3.20 3.00 2.80 PIN 1 INDICATOR 5.15 4.90 4.65 4 PIN 1 IDENTIFIER 0.95 BSC 1.90 BSC 0.65 BSC 0.50 MAX 0.30 MIN 0.95 0.85 0.75 0.20 MAX 0.08 MIN SEATING PLANE 10° 4° 0° 0.55 0.45 0.35 0.60 BSC COMPLIANT TO JEDEC STANDARDS MO-178-AB 15° MAX 1.10 MAX 0.15 0.05 COPLANARITY 0.10 Figure 35. 6-Lead Small Outline Transistor Package [SOT-23] (RJ-6) Dimensions shown in millimeters 0.40 0.25 6° 0° 0.23 0.09 0.80 0.55 0.40 COMPLIANT TO JEDEC STANDARDS MO-187-AA Figure 36. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters ORDERING GUIDE Model 1, 2 AD5310BRTZ-REEL AD5310BRTZ-REEL7 AD5310BRTZ-500RL7 AD5310BRT-REEL AD5310BRT-REEL7 AD5310BRT-500RL7 AD5310WBRTZ-REEL7 AD5310BRMZ AD5310BRMZ-REEL7 AD5310BRM AD5310BRM-REEL 1 2 Temperature Range –40°C to +105°C –40°C to +105°C –40°C to +105°C –40°C to +105°C –40°C to +105°C –40°C to +105°C –40°C to +105°C –40°C to +105°C –40°C to +105°C –40°C to +105°C –40°C to +105°C Package Description 6-Lead SOT-23 6-Lead SOT-23 6-Lead SOT-23 6-Lead SOT-23 6-Lead SOT-23 6-Lead SOT-23 6-Lead SOT-23 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP Package Option RJ-6 RJ-6 RJ-6 RJ-6 RJ-6 RJ-6 RJ-6 RM-8 RM-8 RM-8 RM-8 Branding Information D3B D3B D3B D3B D3B D3B DJW D3B D3B D3B D3B Z = RoHS Compliant Part. W = Qualified for Automotive Applications. AUTOMOTIVE PRODUCTS The AD5310WBRTZ-REEL7 model is available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that this automotive model may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade product shown is available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for this model. ©2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D00933-0-7/12(B) Rev. B | Page 16 of 16 10-07-2009-B 1.45 MAX 0.95 MIN 12-16-2008-A 1.30 1.15 0.90 0.15 MAX 0.05 MIN 1 5