LM2733 0.6/1.6 MHz Boost Converters With 40V Internal FET Switch in SOT-23 General Description Features The LM2733 switching regulators are current-mode boost converters operating fixed frequency of 1.6 MHz (“X” option) and 600 kHz (“Y” option). n n n n n n n n n n The use of SOT-23 package, made possible by the minimal power loss of the internal 1A switch, and use of small inductors and capacitors result in the industry’s highest power density. The 40V internal switch makes these solutions perfect for boosting to voltages of 16V or greater. These parts have a logic-level shutdown pin that can be used to reduce quiescent current and extend battery life. Protection is provided through cycle-by-cycle current limiting and thermal shutdown. Internal compensation simplifies design and reduces component count. X Y 1.6 MHz 0.6 MHz Applications n n n n n Switch Frequency 40V DMOS FET switch 1.6 MHz (“X”), 0.6 MHz (“Y”) switching frequency Low RDS(ON) DMOS FET Switch current up to 1A Wide input voltage range (2.7V–14V) Low shutdown current ( < 1 µA) 5-Lead SOT-23 package Uses tiny capacitors and inductors Cycle-by-cycle current limiting Internally compensated White LED Current Source PDA’s and Palm-Top Computers Digital Cameras Portable Phones and Games Local Boost Regulator Typical Application Circuit 20055424 20055457 20055401 20055458 © 2003 National Semiconductor Corporation DS200554 www.national.com LM2733 0.6/1.6 MHz Boost Converters With 40V Internal FET Switch in SOT-23 February 2003 LM2733 Typical Application Circuit (Continued) 20055440 20055459 Connection Diagram Top View 20055402 5-Lead SOT-23 Package See NS Package Number MF05A Ordering Information Order Number Package Type Package Drawing Supplied As Package ID LM2733XMF 1K Tape and Reel S52A LM2733XMFX 3K Tape and Reel S52A 1K Tape and Reel S52B 3K Tape and Reel S52B LM2733YMF SOT23-5 LM2733YMFX MF05A Pin Description Pin Name 1 SW 2 GND 3 FB 4 SHDN 5 VIN www.national.com Function Drain of the internal FET switch. Analog and power ground. Feedback point that connects to external resistive divider. Shutdown control input. Connect to VIN if this feature is not used. Analog and power input. 2 LM2733 Block Diagram 20055403 the Gm amplifier is derived from the feedback (which samples the voltage at the output), the action of the PWM comparator constantly sets the correct peak current through the FET to keep the output volatge in regulation. Q1 and Q2 along with R3 - R6 form a bandgap voltage reference used by the IC to hold the output in regulation. The currents flowing through Q1 and Q2 will be equal, and the feedback loop will adjust the regulated output to maintain this. Because of this, the regulated output is always maintained at a voltage level equal to the voltage at the FB node "multiplied up" by the ratio of the output resistive divider. The current limit comparator feeds directly into the flip-flop, that drives the switch FET. If the FET current reaches the limit threshold, the FET is turned off and the cycle terminated until the next clock pulse. The current limit input terminates the pulse regardless of the status of the output of the PWM comparator. Theory of Operation The LM2733 is a switching converter IC that operates at a fixed frequency (0.6 or 1.6 MHz) using current-mode control for fast transient response over a wide input voltage range and incorporate pulse-by-pulse current limiting protection. Because this is current mode control, a 50 mΩ sense resistor in series with the switch FET is used to provide a voltage (which is proportional to the FET current) to both the input of the pulse width modulation (PWM) comparator and the current limit amplifier. At the beginning of each cycle, the S-R latch turns on the FET. As the current through the FET increases, a voltage (proportional to this current) is summed with the ramp coming from the ramp generator and then fed into the input of the PWM comparator. When this voltage exceeds the voltage on the other input (coming from the Gm amplifier), the latch resets and turns the FET off. Since the signal coming from 3 www.national.com LM2733 Absolute Maximum Ratings (Note 1) FB Pin Voltage SW Pin Voltage If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Storage Temperature Range Operating Junction Temperature Range −65˚C to +150˚C −0.4V to +40V Input Supply Voltage −0.4V to +14.5V Shutdown Input Voltage (Survival) −0.4V to +14.5V θJ-A (SOT23-5) −40˚C to +125˚C Lead Temp. (Soldering, 5 sec.) Power Dissipation (Note 2) −0.4V to +6V 265˚C/W ESD Rating (Note 3) Human Body Model Machine Model 300˚C Internally Limited 2 kV 200V Electrical Characteristics Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply over the full operating temperature range (−40˚C ≤ TJ ≤ +125˚C). Unless otherwise specified: VIN = 5V, VSHDN = 5V, IL = 0A. Symbol Parameter Conditions VIN Input Voltage ISW Switch Current Limit (Note 6) RDS(ON) Switch ON Resistance ISW = 100 mA SHDNTH Shutdown Threshold Device ON Min (Note 4) Typical (Note 5) 2.7 1.0 14 1.5 500 Shutdown Pin Bias Current 650 0.50 VSHDN = 0 0 VSHDN = 5V 0 2 1.230 1.255 VFB Feedback Pin Reference Voltage VIN = 3V IFB Feedback Pin Bias Current VFB = 1.23V 60 IQ Quiescent Current VSHDN = 5V, Switching "X" 2.1 3.0 VSHDN = 5V, Switching "Y" 1.1 2 400 500 0.024 1 1.205 VSHDN = 5V, Not Switching VSHDN = 0 FB Voltage Line Regulation DMAX IL Switching Frequency Maximum Duty Cycle Switch Leakage V mΩ V µA V nA mA µA 2.7V ≤ VIN ≤ 14V 0.02 FSW Units A 1.5 Device OFF ISHDN Max (Note 4) %/V “X” Option 1.15 1.6 1.85 “Y” Option 0.40 0.60 0.8 “X” Option 87 93 “Y” Option 93 96 Not Switching VSW = 5V MHz % 1 µA Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the device outside of the limits set forth under the operating ratings which specify the intended range of operating conditions. Note 2: The maximum power dissipation which can be safely dissipated for any application is a function of the maximum junction temperature, TJ(MAX) = 125˚C, the junction-to-ambient thermal resistance for the SOT-23 package, θJ-A = 265˚C/W, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature for designs using this device can be calculated using the formula: If power dissipation exceeds the maximum specified above, the internal thermal protection circuitry will protect the device by reducing the output voltage as required to maintain a safe junction temperature. Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. The machine model is a 200 pF capacitor discharged directly into each pin. Note 4: Limits are guaranteed by testing, statistical correlation, or design. Note 5: Typical values are derived from the mean value of a large quantity of samples tested during characterization and represent the most likely expected value of the parameter at room temperature. Note 6: Switch current limit is dependent on duty cycle (see Typical Performance Characteristics). Limits shown are for duty cycles ≤ 50%. www.national.com 4 Unless otherwise specified: VIN = 5V, SHDN pin is tied to VIN. Iq VIN (Active) vs Temperature - "X" Iq VIN (Active) vs Temperature - "Y" 20055410 20055442 Oscillator Frequency vs Temperature - "X" Oscillator Frequency vs Temperature - "Y" 20055408 20055443 Max. Duty Cycle vs Temperature - "X" Max. Duty Cycle vs Temperature - "Y" 20055456 20055455 5 www.national.com LM2733 Typical Performance Characteristics LM2733 Typical Performance Characteristics Unless otherwise specified: VIN = 5V, SHDN pin is tied to VIN. (Continued) Feedback Voltage vs Temperature RDS(ON) vs Temperature 20055407 20055406 Current Limit vs Temperature RDS(ON) vs VIN 20055409 20055423 Efficiency vs Load Current (VOUT = 12V) - "X" Efficiency vs Load Current (VOUT = 15V) - "X" 20055414 www.national.com 20055445 6 Efficiency vs Load Current (VOUT = 20V) - "X" Efficiency vs Load Current (VOUT = 25V) - "X" 20055447 20055446 Efficiency vs Load Current (VOUT = 30V) - "X" Efficiency vs Load Current (VOUT = 35V) - "X" 20055448 20055449 Efficiency vs Load Current (VOUT = 40V) - "X" Efficiency vs Load (VOUT = 15V) - "Y" 20055435 20055450 7 www.national.com LM2733 Typical Performance Characteristics Unless otherwise specified: VIN = 5V, SHDN pin is tied to VIN. (Continued) LM2733 Typical Performance Characteristics Unless otherwise specified: VIN = 5V, SHDN pin is tied to VIN. (Continued) Efficiency vs Load (VOUT = 20V) - "Y" Efficiency vs Load (VOUT = 25V) - "Y" 20055427 20055428 Efficiency vs Load (VOUT = 30V) - "Y" Efficiency vs Load (VOUT = 35V) - "Y" 20055429 20055430 Efficiency vs Load (VOUT = 40V) - "Y" 20055432 www.national.com 8 High frequency switching regulators require very careful layout of components in order to get stable operation and low noise. All components must be as close as possible to the LM2733 device. It is recommended that a 4-layer PCB be used so that internal ground planes are available. As an example, a recommended layout of components is shown: SELECTING THE EXTERNAL CAPACITORS The best capacitors for use with the LM2733 are multi-layer ceramic capacitors. They have the lowest ESR (equivalent series resistance) and highest resonance frequency which makes them optimum for use with high frequency switching converters. When selecting a ceramic capacitor, only X5R and X7R dielectric types should be used. Other types such as Z5U and Y5F have such severe loss of capacitance due to effects of temperature variation and applied voltage, they may provide as little as 20% of rated capacitance in many typical applications. Always consult capacitor manufacturer’s data curves before selecting a capacitor. High-quality ceramic capacitors can be obtained from Taiyo-Yuden, AVX, and Murata. SELECTING THE OUTPUT CAPACITOR A single ceramic capacitor of value 4.7 µF to 10 µF will provide sufficient output capacitance for most applications. For output voltages below 10V, a 10 µF capacitance is required. If larger amounts of capacitance are desired for improved line support and transient response, tantalum capacitors can be used in parallel with the ceramics. Aluminum electrolytics with ultra low ESR such as Sanyo Oscon can be used, but are usually prohibitively expensive. Typical AI electrolytic capacitors are not suitable for switching frequencies above 500 kHz due to significant ringing and temperature rise due to self-heating from ripple current. An output capacitor with excessive ESR can also reduce phase margin and cause instability. 20055422 Recommended PCB Component Layout Some additional guidelines to be observed: 1. Keep the path between L1, D1, and C2 extremely short. Parasitic trace inductance in series with D1 and C2 will increase noise and ringing. 2. The feedback components R1, R2 and CF must be kept close to the FB pin of U1 to prevent noise injection on the FB pin trace. 3. If internal ground planes are available (recommended) use vias to connect directly to ground at pin 2 of U1, as well as the negative sides of capacitors C1 and C2. SELECTING THE INPUT CAPACITOR An input capacitor is required to serve as an energy reservoir for the current which must flow into the coil each time the switch turns ON. This capacitor must have extremely low ESR, so ceramic is the best choice. We recommend a nominal value of 2.2 µF, but larger values can be used. Since this capacitor reduces the amount of voltage ripple seen at the input pin, it also reduces the amount of EMI passed back along that line to other circuitry. SETTING THE OUTPUT VOLTAGE The output voltage is set using the external resistors R1 and R2 (see Basic Application Circuit). A value of approximately 13.3 kΩ is recommended for R2 to establish a divider current of approximately 92 µA. R1 is calculated using the formula: R1 = R2 X (VOUT/1.23 − 1) FEED-FORWARD COMPENSATION Although internally compensated, the feed-forward capacitor Cf is required for stability (see Basic Application Circuit). Adding this capacitor puts a zero in the loop response of the converter. Without it, the regulator loop can oscillate. The recommended frequency for the zero fz should be approximately 8 kHz. Cf can be calculated using the formula: Cf = 1 / (2 X π X R1 X fz) SWITCHING FREQUENCY The LM2733 is provided with two switching frequencies: the “X” version is typically 1.6 MHz, while the “Y” version is typically 600 kHz. The best frequency for a specific application must be determined based on the tradeoffs involved: Higher switching frequency means the inductors and capacitors can be made smaller and cheaper for a given output voltage and current. The down side is that efficiency is slightly lower because the fixed switching losses occur more frequently and become a larger percentage of total power loss. EMI is typically worse at higher switching frequencies because more EMI energy will be seen in the higher frequency spectrum where most circuits are more sensitive to such interference. SELECTING DIODES The external diode used in the typical application should be a Schottky diode. If the switch voltage is less than 15V, a 20V diode such as the MBR0520 is recommended. If the switch voltage is between 15V and 25V, a 30V diode such as the MBR0530 is recommended. If the switch voltage exceeds 25V, a 40V diode such as the MBR0540 should be used. The MBR05XX series of diodes are designed to handle a maximum average current of 0.5A. For applications exceeding 0.5A average but less than 1A, a Microsemi UPS5817 can be used. 9 www.national.com LM2733 LAYOUT HINTS Application Hints LM2733 Application Hints (Continued) 20055405 Basic Application Circuit the inductor current to drop to zero during the cycle. It should be noted that all boost converters shift over to discontinuous operation as the output load is reduced far enough, but a larger inductor stays “continuous” over a wider load current range. To better understand these tradeoffs, a typical application circuit (5V to 12V boost with a 10 µH inductor) will be analyzed. We will assume: VIN = 5V, VOUT = 12V, VDIODE = 0.5V, VSW = 0.5V Since the frequency is 1.6 MHz (nominal), the period is approximately 0.625 µs. The duty cycle will be 62.5%, which means the ON time of the switch is 0.390 µs. It should be noted that when the switch is ON, the voltage across the inductor is approximately 4.5V. Using the equation: V = L (di/dt) We can then calculate the di/dt rate of the inductor which is found to be 0.45 A/µs during the ON time. Using these facts, we can then show what the inductor current will look like during operation: DUTY CYCLE The maximum duty cycle of the switching regulator determines the maximum boost ratio of output-to-input voltage that the converter can attain in continuous mode of operation. The duty cycle for a given boost application is defined as: This applies for continuous mode operation. The equation shown for calculating duty cycle incorporates terms for the FET switch voltage and diode forward voltage. The actual duty cycle measured in operation will also be affected slightly by other power losses in the circuit such as wire losses in the inductor, switching losses, and capacitor ripple current losses from self-heating. Therefore, the actual (effective) duty cycle measured may be slightly higher than calculated to compensate for these power losses. A good approximation for effctive duty cycle is : DC (eff) = (1 - Efficiency x (VIN/VOUT)) Where the efficiency can be approximated from the curves provided. INDUCTANCE VALUE The first question we are usually asked is: “How small can I make the inductor?” (because they are the largest sized component and usually the most costly). The answer is not simple and involves tradeoffs in performance. Larger inductors mean less inductor ripple current, which typically means less output voltage ripple (for a given size of output capacitor). Larger inductors also mean more load power can be delivered because the energy stored during each switching cycle is: E =L/2 X (lp)2 Where “lp” is the peak inductor current. An important point to observe is that the LM2733 will limit its switch current based on peak current. This means that since lp(max) is fixed, increasing L will increase the maximum amount of power available to the load. Conversely, using too little inductance may limit the amount of load current which can be drawn from the output. Best performance is usually obtained when the converter is operated in “continuous” mode at the load current range of interest, typically giving better load regulation and less output ripple. Continuous operation is defined as not allowing www.national.com 20055412 10 µH Inductor Current, 5V–12V Boost (LM2733X) During the 0.390 µs ON time, the inductor current ramps up 0.176A and ramps down an equal amount during the OFF time. This is defined as the inductor “ripple current”. It can also be seen that if the load current drops to about 33 mA, the inductor current will begin touching the zero axis which means it will be in discontinuous mode. A similar analysis can be performed on any boost converter, to make sure the ripple current is reasonable and continuous operation will be maintained at the typical load current values. 10 LM2733 Application Hints (Continued) MAXIMUM SWITCH CURRENT The maximum FET swtch current available before the current limiter cuts in is dependent on duty cycle of the application. This is illustrated in the graphs below which show both the typical and guaranteed values of switch current for both the "X" and "Y" versions as a function of effective (actual) duty cycle: The equation shown to calculate maximum load current takes into account the losses in the inductor or turn-OFF switching losses of the FET and diode. For actual load current in typical applications, we took bench data for various input and output voltages for both the "X" and "Y" versions of the LM2733 and displayed the maximum load current available for a typical device in graph form: 20055425 Switch Current Limit vs Duty Cycle - "X" 20055434 Max. Load Current vs VIN - "X" 20055426 Switch Current Limit vs Duty Cycle - "Y" 20055433 Max. Load Current vs VIN - "Y" CALCULATING LOAD CURRENT As shown in the figure which depicts inductor current, the load current is related to the average inductor current by the relation: ILOAD = IIND(AVG) x (1 - DC) Where "DC" is the duty cycle of the application. The switch current can be found by: ISW = IIND(AVG) + 1⁄2 (IRIPPLE) Inductor ripple current is dependent on inductance, duty cycle, input voltage and frequency: IRIPPLE = DC x (VIN-VSW) / (f x L) combining all terms, we can develop an expression which allows the maximum available load current to be calculated: DESIGN PARAMETERS VSW AND ISW The value of the FET "ON" voltage (referred to as VSW in the equations) is dependent on load current. A good approximation can be obtained by multiplying the "ON Resistance" of the FET times the average inductor current. FET on resistance increases at VIN values below 5V, since the internal N-FET has less gate voltage in this input voltage range (see Typical performance Characteristics curves). Above VIN = 5V, the FET gate voltage is internally clamped to 5V. 11 www.national.com LM2733 Application Hints (Continued) The maximum peak switch current the device can deliver is dependent on duty cycle. The minimum value is guaranteed to be > 1A at duty cycle below 50%. For higher duty cycles, see Typical performance Characteristics curves. THERMAL CONSIDERATIONS At higher duty cycles, the increased ON time of the FET means the maximum output current will be determined by power dissipation within the LM2733 FET switch. The switch power dissipation from ON-state conduction is calculated by: P(SW) = DC x IIND(AVE)2 x RDSON 20055413 Discontinuous Design, 5V–12V Boost (LM2733X) The voltage across the inductor during ON time is 4.8V. Minimum inductance value is found by: V = L X dl/dt, L = V X (dt/dl) = 4.8 (0.524µ/1) = 2.5 µH There will be some switching losses as well, so some derating needs to be applied when calculating IC power dissipation. In this case, a 2.7 µH inductor could be used assuming it provided at least that much inductance up to the 1A current value. This same analysis can be used to find the minimum inductance for any boost application. Using the slower switching “Y” version requires a higher amount of minimum inductance because of the longer switching period. MINIMUM INDUCTANCE In some applications where the maximum load current is relatively small, it may be advantageous to use the smallest possible inductance value for cost and size savings. The converter will operate in discontinuous mode in such a case. The minimum inductance should be selected such that the inductor (switch) current peak on each cycle does not reach the 1A current limit maximum. To understand how to do this, an example will be presented. In the example, the LM2733X will be used (nominal switching frequency 1.6 MHz, minimum switching frequency 1.15 MHz). This means the maximum cycle period is the reciprocal of the minimum frequency: TON(max) = 1/1.15M = 0.870 µs We will assume the input voltage is 5V, VOUT = 12V, VSW = 0.2V, VDIODE = 0.3V. The duty cycle is: Duty Cycle = 60.3% Therefore, the maximum switch ON time is 0.524 µs. An inductor should be selected with enough inductance to prevent the switch current from reaching 1A in the 0.524 µs ON time interval (see below): www.national.com INDUCTOR SUPPLIERS Some of the recommended suppliers of inductors for this product include, but not limited to are Sumida, Coilcraft, Panasonic, TDK and Murata. When selecting an inductor, make certain that the continuous current rating is high enough to avoid saturation at peak currents. A suitable core type must be used to minimize core (switching) losses, and wire power losses must be considered when selecting the current rating. SHUTDOWN PIN OPERATION The device is turned off by pulling the shutdown pin low. If this function is not going to be used, the pin should be tied directly to VIN. If the SHDN function will be needed, a pull-up resistor must be used to VIN (approximately 50k-100kΩ recommended). The SHDN pin must not be left unterminated. 12 inches (millimeters) unless otherwise noted 5-Lead SOT-23 Package Order Number LM2733XMF, LM2733XMFX, LM2733YMF or LM2733YMFX NS Package Number MF05A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Support Center Fax: +65-6250 4466 Email: [email protected] Tel: +65-6254 4466 National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. LM2733 0.6/1.6 MHz Boost Converters With 40V Internal FET Switch in SOT-23 Physical Dimensions