ETC LM2641

LM2641
Dual Adjustable Step-Down Switching Power Supply
Controller
General Description
Key Specifications
The LM2641 is a dual step-down power supply controller
intended for application in notebook personal computers and
other battery-powered equipment.
Fixed-frequency synchronous drive of logic-level N-channel
power MOSFETs is combined with an optional
pulse-skipping mode to achieve ultra efficient power conversion over a 1000:1 load current range. The pulse-skipping
mode can be disabled in favor of fixed-frequency operation
regardless of the load current level.
High DC gain and current-mode feedback control assure
excellent line and load regulation and a wide loop bandwidth
for fast response to dynamic loads.
An internal oscillator fixes the switching frequency at
300 kHz. Optionally, switching can be synchronized to an
external clock running as fast as 400 kHz.
An optional soft-start feature limits current surges from the
input power supply at start up and provides a simple means
of start-up sequencing.
Logic-level inputs allow the controllers to be turned ON and
OFF separately.
n
n
n
n
n
96% efficient
5.5 to 30V input range
Dual outputs adjustable from 2.2 to 8V
0.5% typical load regulation error
0.002%/V typical line regulation error
Features
n 300 kHz fixed-frequency switching
n Switching synchronization with an external signal up to
400 kHz
n Optional pulse-skipping mode
n Adjustable secondary feedback
n Input undervoltage lockout
n Output undervoltage shutdown protection
n Output overvoltage shutdown protection
n Programmable soft-start (each controller)
n 5V, 50 mA linear regulator output
n Precision 2.5V reference output
n 28-pin TSSOP
Applications
n Notebook and subnotebook computers
n Wireless data terminals
n Battery-powered instruments
Connection Diagram and Ordering Information
28-Lead TSSOP (MTC)
10094901
Top View
Order Number LM2641MTC-ADJ
See NS Package Number MTC28
© 2001 National Semiconductor Corporation
DS100949
www.national.com
LM2641 Dual Adjustable Step-Down Switching Power Supply Controller
May 2001
LM2641
Pin Description
Pin #
(Refer to Typical Application Circuits)
Name
Function
1
CSH2
The sense point for the positive side of the voltage across the current sense resistor (R13)
placed in series with output #2.
2
FB2
The regulated output voltage appearing at output #2 is sensed using this pin by connecting it to
the center of the output resistive divider (R15 and R16).
3
COMP2
An R-C network made up of R11, C10, and C12 is connected to this pin which provides loop
compensation for regulated output #2.
4
SS2
This provides programmable soft-start for the #2 output along with capacitor C15.
5
ON/OFF2
This pin turns off only output #2.
6
SD
The part can be put into “sleep” mode using this pin, where both outputs are off and the internal
chip functions are shut down.
7
SYNC
The internal oscillator may be synchronized to an external clock via this pin.
8
GND
Connect this pin to circuit Signal Ground.
9
REF
Internal 2.5V reference voltage. This voltage is turned off by the SD pin, but remains on if either
or both ON/OFF pins are pulled low, which turns off the regulated output(s).
10
2NDFB/FPWM
A 12V supply can be generated using an auxiliary winding on the 5V output inductor. Feedback
to control this 12V output is brought in through this pin. If the 12V supply is not required, this pin
can also force the chip to operate at fixed frequency at light loads by pulling the pin low (this is
the “forced-PWM” mode of operation). This will prevent the converter from operating in
pulse-skipping mode.
11
ON/OFF1
This pin turns off only output #1.
12
SS1
This provides programmable soft-start for the #1 output along with capacitor C3.
13
COMP1
An R-C network made up of R6, C5, and C7 is connected to this pin which provides loop
compensation for regulated output #1.
14
FB1
The regulated output voltage appearing at output #1 is sensed using this pin by connecting it to
the center of the output resistive divider (R1 and R2).
15
CSH1
The sense point for the positive side of the voltage across the current sense resistor (R4) placed
in series with output #1.
16
HDRV1
The drive for the gate of the high-side switching FET used for output #1.
17
SW1
This is the switching output drive point of the two power FETs which produce output #1.
18
CBOOT1
The bootstrap capacitor (C8) for output #1 is returned to this point.
19
LDRV1
The drive for the gate of the low-side switching FET (synchronous rectifier) used for output #1.
20
PGND
Connect this pin to circuit Power Ground.
21
CSL1
The sense point for the negative side of the voltage across the current sense resistor (R4)
placed in series with output #1.
22
LIN
This pin provides a low-current (50 mA max) 5V output. This output is always on, and can not be
turned off by either the SD or ON/OFF pins.
23
IN
This is the connection for the main input power.
24
LDRV2
The drive for the gate of the low-side switching FET (synchronous rectifier) used for output #2.
25
CBOOT2
The bootstrap capacitor (C9) for output #2 is returned to this point.
26
SW2
This is the switching output drive point of the two power FETs which produce output #2.
27
HDRV2
The drive for the gate of the high-side switching FET used for output #2.
28
CSL2
The sense point for the negative side of the voltage across the current sense resistor (R13)
placed in series with output #2.
www.national.com
2
Typical Application Circuits
FIGURE 1. Application With 5V/3A and 3.3V/4A Outputs
10094903
LM2641
3
www.national.com
www.national.com
4
Typical Application Circuits
10094904
FIGURE 2. Application With 5V/3A, 3.3V/4A, and 12V/0.3A Outputs
(Continued)
LM2641
(Notes 2,
Voltage from CBOOT1 to
HDRV1 and from CBOOT2
HDRV2
1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
IN, SW1, and SW2
Junction Temp.
−65 to +150˚C
Soldering Dwell Time, Temp. (Note 4)
Wave
−0.3 to (VLIN +0.3)V
4 sec, 260˚C
Infrared
10 sec, 240˚C
Vapor Phase
75 sec, 219˚C
ESD Rating (Note 5)
LIN
−0.3 to 6V
CSH1, CSH2, and CSL2 (Note
12)
−0.3 to 9V
Voltage from CBOOT1 to SW1
and from CBOOT2 to SW2
−0.3 to 5V
Voltage from HDRV1 to SW1
and from HDRV2 to SW2
883 mW
Ambient Storage Temp. (TJ)
−0.3 to 3V
SD, ON/OFF1, ON/OFF2,
2NDFB/FPWM, SYNC, REF,
SS1, SS2, COMP1,
COMP2 and CSL1
+150˚C
Power Dissipation (Note 3)
−0.3 to 31V
FB1 and FB2
−0.3V
2 kV
Operating Ratings(Notes 1, 2)
VIN
5.5 to 30V
Junction Temp. (TJ)
0 to +125˚C
−0.3V
Electrical Characteristics
Typicals and limits appearing in regular type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, 0 to +125˚C. Unless otherwise specified under the Parameter or Conditions columns, VIN
= 10V, and VSD = VON/OFF1 = VON/OFF2 = 5V. (Notes 2, 6, 7)
Symbol
Parameter
Conditions
Typical
Limit
Units
System
VIN
VOUT1
Input Supply Voltage Range
5.5
V(min)
30
V(max)
Output Voltage Adjustment
Range
2.2
V(min)
6.0
V(max)
VOUT2
Output Voltage Adjustment
Range
2.2
V(min)
8.0
V(max)
∆VOUT/VOUT
Load Regulation
0 mV ≤ (CSH1-CSL1) ≤ 80 mV,
0 mV ≤ (CSH2-CSL2) ≤ 80 mV
∆VOUT/∆VIN
Line Regulation
5.5V ≤ VIN ≤ 30V
IIN
Input Supply Current
ON (Note 8)
0.5
%
0.002
%/V
0.6
mA
VFB1 = VFB2 = 1.4V,
1
mA(max)
150
µA(max)
VCSH1 = 5.2V, VCSL1 = 5V,
VCSH2 = 3.5V, VCSL2 = 3.3V
Standing By (Note 9)
80
VON/OFF1 = VON/OFF2 = 0V
Shut Down (Note 10)
25
VSD = 0V
ISS1, ISS2
VPCL
VNCL
Soft-Start Source Current
VSS1 = VSS2 = 1V
µA
µA
60
µA(max)
2.0
µA(min)
7.0
µA(max)
4.75
µA
Soft-Start Sink Current
10
µA
Positive Current Limit Voltage
(Voltage from CSH1 to CSL1
and from CSH2 to CSL2)
100
mV
Negative Current Limit Voltage V2NDFB/FPWM = 0.8V
(Voltage from CSH1 to CSL1
and from CSH2 to CSL2)
−100
5
80
mV(min)
140
mV(max)
−80
mV(min)
−140
mV(max)
mV
www.national.com
LM2641
Absolute Maximum Ratings
LM2641
Electrical Characteristics
(Continued)
Typicals and limits appearing in regular type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, 0 to +125˚C. Unless otherwise specified under the Parameter or Conditions columns, VIN
= 10V, and VSD = VON/OFF1 = VON/OFF2 = 5V. (Notes 2, 6, 7)
Symbol
Parameter
Conditions
Typical
VOUT Undervoltage Shutdown
Latch Threshold
70
VOUT Overvoltage Shutdown
Latch Threshold
150
Secondary Feedback
Threshold Voltage
(2NDFB/FPWM)
(2NDFB/FPWM) Pin
Pull-Up Current
Limit
Units
60
%(min)
80
%(max)
135
%(min)
165
%(max)
2.4
V(min)
2.6
V(max)
80
µA(max)
%
%
2.5
VSFB = 2.4V
VON/OFF1 = 0V
VON/OFF2 = 5V
(2NDFB/FPWM) Pin
Input Leakage Current
40
V
± 0.1
µA
4.5
V
Gate Drive
VBOOT
Bootstrap Voltage (Voltage
from CBOOT1 to SW1 and
from CBOOT2 to SW2)
CBOOT1 and CBOOT2 Source
1µA Each
4.3
V(min)
HDRV1 and HDRV2 Sink and
Source Current
0.35
A
LDRV1 and LDRV2 Sink and
Source Current
0.35
A
HDRV1 and HDRV2 High-Side VCBOOT1 = VCBOOT2 = 5V, VSW1 =
On-Resistance
VSW2 = 0V
6
Ω
HDRV1 and HDRV2 Low-Side VCBOOT1 = VCBOOT2 = 5V, VSW1 =
On-Resistance
VSW2 = 0V
4
Ω
LDRV1 and LDRV2 High-Side VLIN = 5V
On-Resistance
8
Ω
LDRV1 and LDRV2 Low-Side
On-Resistance
4
Ω
VLIN = 5V
Oscillator
FOSC
Oscillator Frequency
Minimum OFF-Time
300
VFB1 =1V, Measured at HDRV1
SYNC Pulses are Low-Going
Feedback Input Bias Current
VFB1 = VFB2 = 1.4V
kHz(min)
345
kHz(max)
350
ns(max)
400
kHz(min)
200
ns(min)
250
nA(max)
40
µA(min)
250
Maximum Frequency of
Synchronization
Minimum Width of
Synchronization Pulses
kHz
255
ns
Error Amplifier
IFB1, IFB2
ICOMP1, ICOMP2
ICOMP1, ICOMP2
COMP Output Source Current VFB1 = VFB2 = 1V, VCOMP1 =
VCOMP2 = 1V
90
COMP Output Sink Current
60
VFB1 = VFB2 = 1.4V, VCOMP1 =
VCOMP2 = 0.2V
Voltage References and Linear Voltage Regulator
www.national.com
100
6
nA
µA
µA
40
µA(min)
(Continued)
Typicals and limits appearing in regular type apply for TJ = 25˚C. Limits appearing in boldface type apply over the entire junction temperature range for operation, 0 to +125˚C. Unless otherwise specified under the Parameter or Conditions columns, VIN
= 10V, and VSD = VON/OFF1 = VON/OFF2 = 5V. (Notes 2, 6, 7)
Symbol
Parameter
VBG
Bandgap Voltage
VREF
Reference Voltage
VLIN
VUVLO
Conditions
0.01 mA ≤ IREF ≤ 5 mA Source,
VLIN ≤ 6V
Output Voltage of the Linear
Voltage Regulator
6V ≤ VIN ≤ 30V,
0 mA ≤ ILIN ≤ 25 mA
Undervoltage Lockout
Threshold
(Note 11)
LIN-to-VOUT Switch-Over
Threshold
VOUT taken at CSL1
Typical
Limit
Units
1.238
V
2.5
V
2.45
V(min)
2.55
V(max)
4.6
V(min)
5.4
V(max)
3.6
V(min)
4.4
V(max)
5
V
4.0
V
4.8
V
Logic Inputs
VIH
Minimum High Level Input
Voltage (SD, ON/OFF1,
ON/OFF2, and SYNC)
2.4
V(min)
VIH
Minimum High Level Input
Voltage (2NDFB/FPWM)
2.6
V(min)
VIL
Maximum Low Level Input
Voltage (SD, ON/OFF1,
ON/OFF2, SYNC, and
2NDFB/FPWM)
0.8
V(max)
Maximum Input Leakage
Current (SD, ON/OFF1,
ON/OFF2, and SYNC)
Logic Input Voltage 0 or 5V
± 0.1
µA
Note 1: Unless otherwise specified, all voltages are with respect to the voltage at the GND and PGND pins.
Note 2: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device
is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical
Characteristics tables.
Note 3: The Absolute Maximum power dissipation depends on the ambient temperature. The 883 mW rating results from substituting 150˚C, 70˚C, and 90.6˚C/W
for TJmax, TA, and θJA respectively into the formula Pmax = (TJmax - TA)/θJA, where Pmax is the Absolute Maximum power dissipation, TJmax is the Absolute Maximum
junction temperature, TA is the ambient temperature, and θJA is the junction-to-ambient thermal resistance of the package. A θJA of 90.6˚C/W represents the
worst-case condition of no heat sinking of the 28-pin TSSOP. Heat sinking allows the safe dissipation of more power. The Absolute Maximum power dissipation must
be derated by 11.04 mW per ˚C above 70˚C ambient. The LM2641 actively limits its junction temperature to about 150˚C.
Note 4: For detailed information on soldering plastic small-outline packages, refer to the Packaging Databook available from National Semiconductor Corporation.
Note 5: For testing purposes, ESD was applied using the human-body model, a 100 pF capacitor discharged through a 1.5 kΩ resistor.
Note 6: A typical is the center of characterization data taken with TA = TJ = 25˚C. Typicals are not guaranteed.
Note 7: All limits are guaranteed. All electrical characteristics having room-temperature limits are tested during production with TA = 25˚C. All hot and cold limits are
guaranteed by correlating the electrical characteristics to process and temperature variations and applying statistical process control.
Note 8: Both controllers are ON but not switching. Currents entering the IC at IN, CSL1, CSH1, CSL2, and CSH2 are measured. Those entering at CSL1 and CSH1
are multiplied by 0.50 to emulate the effect of a switching conversion from 10V down to 5V. Those entering at CSL2 and CSH2 are multiplied by 0.33 to emulate
the effect of a switching conversion from 10V down to 3.3V. After multiplication, all five currents are added. Because the voltage at the CSL1 input is greater than
the LIN-to-VOUT switchover threshold, most of the input supply current enters the IC via the CSL1 input.
Note 9: Both switching controllers are OFF. The 5V, 50 mA linear regulator (output at LIN) and the precision 2.5V reference (output at REF) remain ON.
Note 10: Both switching controllers and the 2.5V precision reference are OFF. The 5V, 50 mA linear regulator remains ON.
Note 11: The controllers remain OFF until the voltage of the 5V, 50 mA linear regulator (output at LIN) reaches this threshold.
Note 12: In applications where the output voltage can exceed the absolute maximum rating, a 100Ω resistor must be placed in series with the CSH and CSL inputs.
7
www.national.com
LM2641
Electrical Characteristics
LM2641
Block Diagram
10094902
FIGURE 3. LM2641 Block Diagram
www.national.com
8
Efficiency vs Load Current
Efficiency vs Load Current
10094914
Efficiency vs Load Current
10094915
Efficiency vs Load Current
10094917
Efficiency vs Load Current
10094918
Efficiency vs Load Current
10094920
Ref Output Voltage
10094921
10094924
9
10094916
Efficiency vs Load Current
10094919
Efficiency vs Load Current
10094922
Normalized Switching Output
Voltage vs
Junction Temperature
Ref Output Voltage
10094923
Efficiency vs Load Current
10094925
www.national.com
LM2641
Typical Performance Charateristics
LM2641
Typical Performance Charateristics
Normalized Error Amplifier Voltage
vs
Junction Temperature
(Continued)
Error Amplifier Gm vs
Junction Temperature
10094926
10094927
Shutdown Quiescent Current
And Standby Quiescent Current vs
Supply Voltage
10094929
www.national.com
10
Normalized Oscillator Frequency vs
Junction Temperature
10094928
All current-mode controllers require the use of ramp compensation to prevent subharmonic oscillations, and this compensation is built into the LM2641. The internal compensation assumes an RSENSE value of 25 mΩ, inductor value of
6.8µH, and a maximum output voltage of 6V.
Basic Operation of the Current-Mode Controller
The output voltage is held at a constant value by the main
control loop, which is made up of the error amplifier, the
current sense amplifier, and the PWM comparator (refer to
the Block Diagram, Figure 3).
The LM2641 controller has two primary modes of operation:
Forced Pulse-Width Modulation (FPWM) where the controller always operates at a fixed frequency, and Pulse-Skipping
mode where the controller frequency decreases at reduced
output loads to improve light-load efficiency.
FPWM Mode of Operation
Pulling the FPWM pin low initiates a mode of operation
called Forced Pulse-Width Modulation (FPWM). This means
that the LM2641 will always operate at a fixed frequency,
regardless of output load. The cycle of operation is:
The high-side FET switch turns ON at the beginning of every
clock cycle, causing current to flow through the inductor. The
inductor current ramps up, causing a voltage drop across the
sense resistor, and this voltage is amplified by the current
sense amplifier.
The voltage signal from the current sense amplifier is applied
to the input of the PWM comparator, where it is compared to
the control level set by the error amplifier. Once the current
sense signal reaches this control voltage, the PWM comparator resets the driver logic which turns OFF the high-side
FET switch.
The low-side FET switch turns on after a delay time which is
the lesser of either:
(a) The time it takes the SW pin voltage to reach zero (this
voltage is sensed by the shoot-through protection circuitry).
(b) 100 ns, which is the pre-set value for maximum delay.
When operating at very light loads (in FPWM mode), the
inductor current must flow in a negative direction through the
low-side FET switch in order to maintain the fixed-frequency
mode of operation. For this reason, the built-in zero cross
detector is disabled when ever FPWM mode is activated
(that is, when ever the FPWM pin is pulled to a low state).
It should be noted that if the FPWM pin is high (operation
described in next section), the zero cross detector will turn
OFF the low-side FET switch anytime the inductor current
drops to zero (which prevents negative inductor current).
Pulse-Skipping Mode of Operation
Pulling the FPWM pin high allows the LM2641 to operate in
pulse-skipping mode at light loads, where the switching frequency decreases as the output load is reduced. The controller will operate in fixed-frequency mode, as described in
the previous section, if the output load current is sufficiently
high.
Pulse-skipping results in higher efficiency at light loads, as
decreasing the switching frequency reduces switching
losses. The load current value where the transition from
fixed-frequency to pulse-skipping operation occurs is the
point where the inductor current goes low enough to cause
the voltage measured across the current sense resistor (R4
or R13) to drop below 25 mV.
In pulse-skipping mode, the high-side FET switch will turn
ON at the beginning of the first clock cycle which occurs after
the voltage at the feedback pin falls below the reference
voltage. The high-side FET switch remains ON until the
voltage across the current sense resistor rises to 25 mV (and
then it turns OFF).
To prevent oscillations, the slope M of the compensation
ramp must be equal to the maximum downward slope of the
voltage waveform at the output of the current sense amplifier. The relationship of the slope M to the external components is given by:
MCOMP = MCS AMP (max) = N X RSENSE X VOUT (max) / L
Where:
MCOMP is the slope of the compensation ramp.
MCS AMP (max) is the maximum downward slope of the
voltage at the output of the current sense amplifier.
N is the gain of the current sense amplifier.
RSENSE is the value of the current sense resistor.
VOUT (max) is the maximum output voltage.
L is the inductance of the output inductor.
It is important to note that since the value RSENSE appears in
the numerator and L is in the denominator, these two values
may be increased or decreased at the same ratio without
changing the slope.
At higher values of load current, a lower value RSENSE will be
selected. The inductance value for the output inductor
should be decreased by the same percentage to maintain
correct ramp compensation.
Application Information
Improved Transient Response
If the output voltage falls below 97% of the nominal value,
the low-voltage regulation (LREG) comparator will activate
logic which turns ON the high-side FET switch continuously
until the output returns to nominal. The low-side FET switch
is held OFF during this time.
This action will improve transient response since it bypasses
the error amplifier and PWM comparator, forcing the
high-side switch ON until the output returns to nominal. This
feature is disabled during start-up.
Boost High-Side Gate Drive
A “flying” bootstrap capacitor is used to generate the gate
drive voltage used for the high-side FET switch. This bootstrap capacitor is charged up to about 5V using an internal
supply rail and diode when ever the low-side FET switch is
ON. When the high-side FET switch turns ON, the Source is
pulled up near the input voltage. The voltage across the
bootstrap capacitor boosts up the gate drive voltage, ensuring that the Gate is driven at least 4.3V higher than the
Source.
Reference
The internal bandgap reference is used to generate a 2.5V
reference voltage which is connected to the REF pin. The
guaranteed tolerance of the REF voltage is ± 2% over the full
operating temperature range, as long as the current drawn is
≤ 5 mA.
A bypass capacitor on the REF pin is not required, but may
be used to reduce noise.
11
www.national.com
LM2641
Ramp Compensation
Theory of Operation
LM2641
Application Information
If the sync function is not used, the SYNC pin must be
connected to the LIN pin or to ground to prevent false
triggering.
(Continued)
5V LIN Output
The LM2641 contains a built-in 5V/50 mA LDO regulator
whose output is connected to the LIN pin. Since this is an
LDO regulator, it does require an external capacitor to maintain stability. The minimum amount of capacitance required
for stability is 4.7 µF, with ESR in the range of about 100 mΩ
to 3Ω. A good quality solid Tantalum capacitor is recommended (ceramics can not be used because the ESR is too
low). If cold temperature operation is required, a capacitor
must be selected which has an ESR that is in the stable
range over the entire operating temperature range of the
application.
Since the current limit for this LDO regulator is set at about
85 mA, it can be used at load currents up to about 50 mA
(assuming total IC power dissipation does not exceed the
maximum value).
Guaranteed specifications are provided for worst-case values of VLIN over the full operating temperature range for load
currents up to 25mA (see Electrical Characteristics). To estimate how the VLIN output voltage changes when going from
ILIN = 25mA to ILIN = 50mA, a change in VLIN of about
−30mV should be expected due to loading (typical value
only, not guaranteed). This decrease in VLIN is linear with
increasing load current.
It must be understood that the maximum allowable current of
50mA must include the current drawn by the gate drive
circuitry. This means that the maximum current available for
use at the LIN pin is 50 mA minus whatever is being used
internally for gate drive.
The amount of current used for gate drive by each switching
output can be calculated using the formula:
IGD = 2 X Q X FOSC
Current Limit Circuitry
The LM2641 is protected from damage due to excessive
output current by an internal current limit comparator, which
monitors output current on a cycle-by-cycle basis. The current limiter activates when ever the absolute magnitude of
the voltage developed across the output sense resistor exceeds 100 mV (positive or negative value).
If the sensed voltage exceeds 100 mV, the high-side FET
switch is turned OFF. If the sensed voltage goes below -100
mV, the low-side FET switch is turned OFF. It should be
noted that drawing sufficient output current to activate the
current limit circuits can cause the output voltage to drop,
which could result in a under-voltage latch-OFF condition
(see next section).
Under-voltage/Over-voltage Protection
The LM2641 contains protection circuitry which activates if
the output voltage is too low (UV) or too high (OV). In the
event of either a UV or OV fault, the LM2641 is latched off
and the high-side FET is turned off, while the low-side FET is
turned on.
If the output voltage drops below 70% of nominal value, the
under-voltage comparator will latch OFF the LM2641. To
restore operation, power to the device must be shut off and
then restored.
It should be noted that the UV latch provides protection in
cases where excessive output current forces the output
voltage down. The UV latch circuitry is disabled during
start-up.
If the output voltage exceeds 150% of nominal, the
over-voltage comparator latches off the LM2641. As stated
before, power must be cycled OFF and then ON to restore
operation.
It must be noted that the OV latch can not protect the load
from damage in the event of a high-side FET switch failure
(where the FET shorts out and connects the input voltage to
the load).
Protection for the load in the event of such a failure can be
implemented using a fuse in the power lead. Since the
low-side FET switch turns ON whenever the OV latch activates, this would blow a series fuse if the FET and fuse are
correctly sized.
Where:
IGD is the gate drive current supplied by VLIN.
Q is the gate charge required by the selected FET (see FET
data sheet: Gate Charge Characteristics).
FOSC is the switching frequency.
Example: As shown in the typical application, if the FET
NDS8410 is used with the LM2641, the turn-on gate voltage
(VGS) is 5V − VDIODE = 4.3V. Referring to the NDS8410 data
sheet, the curve Gate Charge Characteristics shows that the
gate charge for this value of VGS is about 24 nC.
Assuming 300 kHz switching frequency, the gate drive current used by each switching output is:
IGD = 2 X Q X FOSC
= 2 X (24 X 10−9) X (3 X 105)
= 14.4 mA
If both outputs are switching, the total gate drive current
drawn would be twice (28.8 mA).
Note that in cases where the voltage at switching output #1
is 4.8V or higher, the internal gate drive current is obtained
from that output (which means the full 50 mA is available for
external use at the LIN pin).
Soft-Start
An internal 5 µA current source connected to the soft-start
pins allows the user to program the turn-on time of the
LM2641. If a capacitor is connected to the SS pin, the
voltage at that pin will ramp up linearly at turn ON. This
voltage is used to control the pulse widths of the FET
switches.
The pulse widths start at a very narrow value and linearly
increase up to the point where the SS pin voltage is about
1.3V. At that time, the pulse-to-pulse current limiter controls
the pulse widths until the output reaches its nominal value
(and the PWM current-mode control loop takes over).
The LM2641 contains a digital counter (referenced to the
oscillator frequency) that times the soft-start interval. The
maximum allotted SS time period is 4096 counts of the
oscillator clock, which means the time period varies with
oscillator frequency:
max. allowable SS interval = 4096 / FOSC
SYNC Pin
The basic operating frequency of 300kHz can be increased
to up to 400kHz by using the SYNC pin and an external
CMOS or TTL clock. The synchronizing pulses must have a
minimum pulse width of 200 ns.
www.national.com
12
are recommended as they generally provide the best
cost/performance characteristics and maintain a very
low ESR even at cold temperatures. Ceramic capacitors
also have very low ESR over the full temperature range,
but X5R/X7R dielectric types should be used to assure
sufficient capacitance will be provided (Z5U or Y5F
types are not suitable).
(Continued)
If the output voltage does not move to within −1% of nominal
in the period of 4096 counts, the device will latch OFF. To
restore operation, the power must be cycled OFF to ON.
Minimum Pulse Width
As the input voltage is increased, the pulse widths of the
switching FET’s decreases. If the pulse widths become narrower than 350ns, pulse jitter may occur as the pulses
alternate with slightly different pulse widths. This is does not
affect regulator stability or output voltage accuracy.
Start-Up Issues
The LM2641 contains an output undervoltage protection
circuit which is made up of a digital counter and a comparator which monitors VOUT. During turn-on, the counter begins
counting clock cycles when the input voltage reaches approximately 3V. If the counter reaches 4096 cycles before
the output voltage rises to within 1% of nominal value, the IC
will be latched off in an undervoltage fault condition.
The function of this protection is to shut the regulator off if the
output is overloaded (such as a short to ground). However,
the UV latch can cause start-up problems if the circuit is not
properly designed. The following two sections explain how to
avoid these types of problems:
2.
Some of the newer electrolytic types such as POSCAP,
OSCON, and polymer electrolytic may also be usable as
input capacitors. However, care must be taken if the
application will be used at low temperatures as the ESR
of these capacitors may increase significantly at temperatures below 0˚C. Most aluminum electrolytes are
not usable with this IC at temperatures below this limit.
Check the ESR specifications of the selected capacitor
carefully if low temperature operation will be required.
The input capacitors must be physically located not
more than one centimeter away from the switching
FET’s, as trace inductance in the switching current path
can cause problems.
Loop Compensation
The LM2641 must be properly compensated to assure
stable operation and good transient response. As with any
control loop, best performance is achieved when the compensation is optimized so that maximum bandwidth is obtained while still maintaining sufficient phase margin for good
stability.
Best performance for the LM2641 is typically obtained when
the loop bandwidth (defined as the frequency where the loop
gain equals unity) is in the range of FOSC/10 to FOSC/5.
In the discussion of loop stability, it should be noted that
there is a high-frequency pole fp(HF), whose frequency can
be approximated by:
fp(HF) ∼ FOSC/2 X QS (Assumes QS < 0.5)
Input Voltage Rise Time
If the input voltage rises too slowly, the LM2641 will latch off
in an undervoltage condition. To avoid this problem, the input
voltage must rise quickly enough to allow the output to get
into regulation before the 4096 count time interval elapses.
For a switching frequency of 300 kHz, 4096 cycles will be
completed in 13.6 milliseconds.
In reality, the total rise time of VIN should not approach the
4096 clock cycle limit if reliable start-up is to be assured. It
should be noted that the total rise time of VIN is also affected
by current loading when the power converter begins switching (which draws power from the input capacitors) causing
their voltage to sag (details of input capacitor requirements
are outlined in the next section).
It is also important to note that this type of start-up problem
is more likely to occur at higher values of output voltage,
since the input voltage must rise to a higher voltage to allow
the output voltage to regulate (which means the input dV/dt
rate has to be faster). The recommended output voltage limit
of 6V should not be exceeded.
Where:
As can be seen in the approximation for QS, the highest
frequency for fp(HF) occurs at the maximum value of VIN.
The lowest frequency for fp(HF) is about FOSC/10 (when VIN
= 4.5V and VOUT = 1.8V).
As noted above, the location of the pole fp(HF) is typically in
the range of about FOSC/10 to FOSC/4. This pole will often be
near the unity-gain crossover frequency, and it can significantly reduce phase margin if left uncompensated. Fortunately, the ESR of the output capacitor(s) forms a zero which
is usually very near the frequency of fp(HF), and provides
cancellation of the negative phase shift it would otherwise
cause. For this reason, the output capacitor must be carefully selected.
Most of the loop compensation for the LM2641 is set by an
R-C network from the output of the error amplifier to ground
(see Figure 4). Since this is a transconductance amplifier, it
has a very high output impedance (160 kΩ).
Input Capacitance
The amount and type of input capacitance present is directly
related to how well the regulator can start up. The reason is
that the input capacitors serve as the source of energy for
the power converter when the regulator begins switching.
Typically, the input voltage (which is the voltage across the
input capacitors) will sag as the power converter starts drawing current which will cause a dip in VIN as it is ramping up.
If the input capacitors are too small or have excessive ESR,
the input volatge may not be able to come up fast enough to
allow the output volatge to get into regulation before the
digital clock counts off 4096 cycles and the part will latch off
as an undervoltage fault.
To prevent this type of start-up problem:
1. The input capacitors must provide sufficient bulk capacitance and have low impedance. Solid Tantalum capacitors designed for high-frequency switching applications
13
www.national.com
LM2641
Application Information
LM2641
Application Information
would cause −180˚ of phase shift at the unity-gain crossover,
which is clearly unstable. Best results are typically obtained
if R11 is selected such that the frequency of fz(R11) is in the
range of fc/4 to fc where fc is the unity-gain crossover frequency.
(Continued)
The output capacitor (along with the load resistance RL)
forms a pole shown as fp(COUT). Although the frequency of
this pole varies with RL, the loop gain also varies proportionally which means the unity-gain crossover frequency stays
essentially constant regardless of RL value.
C12 can be used to create an additional pole most often
used for bypassing high-frequency switching noise on the
COMP pin. In many applications, this capacitor is unnecessary.
If C12 is used, best results are obtained if the frequency of
the pole is set in the range FOSC/2 to 2FOSC. This will provide
bypassing for the high-frequency noise caused by switching
transitions, but add only a small amount of negative phase
shift at the unity-gain crossover frequency.
The ESR of COUT (as well as the capacitance of COUT) form
the zero fz(ESR), which typically falls somewhere between
10kHz and 50kHz. This zero is very important, as it cancels
phase shift caused by the high-frequency pole fp(HF). It is
important to select COUT with the correct value of capacitance and ESR to place this zero near fc (typical range fc/2 to
fc).
As an example, we will present an analysis of the loop gain
plot for a 3.3V design. Values used for calculations are:
VIN = 12V
10094905
FIGURE 4. Typical Compensation Network
The components shown will add poles and zeros to the loop
gain as given by the following equations:
C10 adds a pole whose frequency is given by:
fp(C10) = 1 / [2π X C10 (R11 + 160k) ]
C12 adds a pole whose frequency is given by:
fp(C12) = 1 / [2π X C12 (R11 || 160k) ]
R11 adds a zero whose frequency is given by:
fz(R11) = 1 / [2π X R11 (C10 + C12) ]
The output capacitor adds both a pole and a zero to the loop:
fp(COUT) = 1 / [2π X RL X COUT]
fz(ESR) = 1 / [2π X ESR X COUT]
Where RL is the load resistance, and ESR is the equivalent
series resistance of the output capacitor(s).
The function of the compensation components will be explained in a qualitative discussion of a typical loop gain plot
for an LM2641 application, as illustrated in Figure 5.
VOUT = 3.3V @ 4A
COUT = C14 + C16 = 200 µF
ESR = 60 mΩ(each) = 30mΩ total
FOSC = 300kHz
fp(HF) ∼ 40kHz
R13 = 20mΩ
L2 = 6.8 µH
RL = 0.825Ω
DC gain = 55dB
The values of compensation components will be: C10 =
2200 pF, R11 = 8.2k, and C12 will not be used. Using this
data, the poles and zeros are calculated:
fp(C10) = 1 / [2π X C10 (R11 + 160k) ] = 430Hz
fz(R11) = 1 / [2π X R11 (C10 + C12) ] = 8.8kHz
fp(COUT) = 1 / [2π X RL X COUT] = 960Hz
fz(ESR) = 1 / [2π X ESR X COUT] = 27kHz
fp(HF) ∼ 40kHz
Using these values, the calculated gain plot is shown in
Figure 6.
10094906
FIGURE 5. Typical Loop Gain Plot
C10 and R11 form a pole and a zero. Changing the value of
C10 moves the frequency of both the pole and the zero.
Changing R11 moves the zero without significantly affecting
the pole.
The C10 pole is typically referred to as the dominant pole,
and its primary function is to roll off loop gain and reduce the
bandwidth.
The R11 zero is required to add some positive phase shift to
offset some of the negative phase shift from the two
low-frequency poles. Without this zero, these two poles
www.national.com
14
Optimizing Stability
(Continued)
The best tool for measuring both bandwidth and phase
margin is a network analyzer. If this is not available, a simple
method which gives a good measure of loop stability is to
apply a minimum to maximum step of output load current
and observe the resulting output voltage transient. A design
which has good phase margin ( > 50˚) will typically show no
ringing after the output voltage transient returns to its nominal value.
It should be noted that the stability (phase margin) does not
have to be optimal for the regulator to be stable. The design
analyzed in the previous section was re-compensated by
changing R11 and C10 to intentionally reduce the phase
margin to about 35˚ and re-tested for step response. The
output waveform displayed slight ringing after the initial return to nominal, but was completely stable otherwise.
In most cases, the compensation components shown in the
Typical Application Circuits will give good performance. To
assist in optimizing phase margin, the following guidelines
show the effects of changing various components.
COUT: Increasing the capacitance of COUT moves the frequency of the pole fp(COUT) to a lower value and reduces
loop bandwidth. Increasing COUT can be beneficial (increasing the phase margin) if the loop bandwidth is too wide
( > FOSC/5) which places the high-frequency poles too close
to the unity-gain crossover frequency.
ESR of COUT: The ESR forms a zero fz(ESR), which is
needed to cancel negative phase shift near the unity-gain
frequency. High-ESR capacitors can not be used, since the
zero will be too low in frequency which will make the loop
bandwidth too wide.
R11/C10: These form a pole and a zero. Changing the value
of C10 changes the frequency of both the pole and zero.
Note that since this causes the frequency of both the pole
and zero to move up or down together, adjusting the value of
C10 does not significantly affect loop bandwidth.
Changing the value of R11 moves the frequency location of
the zero fz(R11), but does not significantly shift the C10 pole
(since the value of R11 is much less than the 160kΩ output
impedance of the Gm amplifier). Since only the zero is
moved, this affects both bandwidth and phase margin. This
means adjusting R11 is an easy way to maximize the positive phase shift provided by the zero. Best results are typically obtained if fz(R11) is in the frequency range of fc/4 to fc
(where fc is the unity-gain crossover frequency).
10094907
FIGURE 6. Calculated Gain Plot for 3.3V/4A Application
Looking at the plot, it can be seen that the unity-gain crossover frequency fc is expected to be about 25kHz. Using this
value, the phase margin at the point is calculated to be about
84˚.
To verify the accuracy of these calculations, the circuit was
bench tested using a network analyzer. The measured gain
and phase are shown plotted in Figure 7.
Design Procedure
This section presents guidelines for selecting external components.
10094908
FIGURE 7. Measured Gain/Phase Plot for 3.3V/4A
Application
INDUCTOR SELECTION
In selecting an inductor, the parameters which are most
important are inductance, current rating, and DC resistance.
Inductance
It is important to understand that all inductors are not created
equal, as the method of specifying inductance varies widely.
It must also be noted that the inductance of every inductor
decreases with current. The core material, size, and construction type all contribute the the inductor’s dependence
on current loading. Some inductors exhibit inductance
curves which are relatively flat, while others may vary more
than 2:1 from minimum to maximum current. In the latter
The measured gain plot agrees very closely to the predicted
values. The phase margin at 0dB is slightly less than predicted (71˚ vs. 84˚), which is to be expected due to the
negative phase shift contributions of high frequency poles
not included in this simplified analysis.
It should be noted that 70˚ phase margin with 25kHz bandwidth is excellent, and represents the optimal compensation
for this set of values for VIN, VOUT, inductor and RL.
15
www.national.com
LM2641
Application Information
LM2641
Design Procedure
tance at the operating current of the application) will cost
money in other places.
(Continued)
case, the manufacturer’s specified inductance value is usually the maximum value, which means the actual inductance
in your application will be much less.
INPUT CAPACITORS
The switching action of the high-side FET requires that high
peak currents be available to the switch or large voltage
transients will appear on the VIN line. To supply these peak
currents, a low ESR capacitor must be connected between
the drain of the high-side FET and ground. The capacitor
must be located as close as possible to the FET (maximum
distance = 0.5 cm).
A solid Tantalum or low ESR aluminum electrolytic can be
used for this capacitor. If a Tantalum is used, it must be able
to withstand the turn-ON surge current when the input power
is applied. To assure this, the capacitor must be surge tested
by the manufacturer and guaranteed to work in such applications.
Caution: If a typical off-the-shelf Tantalum is used that has
not been surge tested, it can be blown during power-up and
will then be a dead short. This can cause the capacitor to
catch fire if the input source continues to supply current.
Voltage Rating
For an aluminum electrolytic, the voltage rating must be at
least 25% higher than the maximum input voltage for the
application.
Tantalum capacitors require more derating, so it is recommended that the selected capacitor be rated to work at a
voltage that is about twice the maximum input voltage.
Current Rating
Capacitors are specified with an RMS current rating. To
determine the requirement for an application, the following
formula can be used:
An inductor with a flatter inductance curve is preferable,
since the loop characteristics of any switching converter are
affected somewhat by inductance value. An inductor which
has a more constant inductance value will give more consistent loop bandwidth when the load current is varied.
The data sheet for the inductor must be reviewed carefully to
verify that the selected component will have the desired
inductance at the frequency and current for the application.
Current Rating
This specification may be the most confusing of all when
picking an inductor, as manufacturers use different methods
for specifying an inductor’s current rating.
The current rating specified for an inductor is typically given
in RMS current, although in some cases a peak current
rating will also be given (usually as a multiple of the RMS
rating) which gives the user some indication of how well the
inductance operates in the saturation region.
Other things being equal, a higher peak current rating is
preferred, as this allows the inductor to tolerate high values
of ripple current without significant loss of inductance.
In the some cases where the inductance vs. current curve is
relatively flat, the given current rating is the point where the
inductance drops 10% below the nominal value. If the inductance varies a lot with current, the current rating listed by the
manufacturer may be the “center point” of the curve. This
means if that value of current is used in your application, the
amount of inductance will be less than the specified value.
DC Resistance
The DC resistance of the wire used in an inductor dissipates
power which reduces overall efficiency. Thicker wire decreases resistance, but increases size, weight, and cost. A
good tradeoff is achieved when the inductor’s copper wire
losses are about 2% of the maximum output power.
Selecting An Inductor
Determining the amount of inductance required for an application can be done using the formula:
It is also recommended that a 0.1µF ceramic capacitor be
placed from VIN to ground for high frequency bypassing,
located as close as possible to the VIN pin.
OUTPUT CAPACITORS
The output capacitor(s) are critical in loop stability (covered
in a previous section) and also output voltage ripple.
The types best suited for use as output capacitors are aluminum electrolytics and solid Tantalum.
Aluminum Electrolytics
The primary advantage of aluminum electrolytics is that they
typically give the maximum capacitance-to-size ratio, and
they are reasonably priced. However, it must be noted that
aluminum electrolytics used in high-performance switching
regulator designs must be high frequency, low ESR types
such as Sanyo OSCON or Panasonic HFQ which are specifically designed for switching applications. Capacitors such
as these with good high frequency (≥ 100kHz) specifications
are not cheap.
Aluminum electrolytic capacitors should generally not be
used in switching regulator applications where the ambient
temperature goes below 0˚C. A typical low-voltage aluminum
electrolytic has an ESR vs. Temperature curve that is fairly
flat from 25˚C to 125˚C. However, a temperature change
from 25˚C to 0˚C will approximately double the ESR, and it
will double again going from 0˚C down to −20˚C.
Tantalum
Where:
VIN is the maximum input voltage.
VOUT is the output voltage.
F is the switching frequency, FOSC
IRIPPLE is the inductor ripple current. In general, a good value
for this is about 30% of the DC output current.
It can be seen from the above equation, that increasing the
switching frequency reduces the amount of required inductance proportionally. Of course, higher frequency operation
is typically less efficient because switching losses become
more predominant as a percentage of total power losses.
It should also be noted that reducing the inductance will
increase inductor ripple current (other terms held constant).
This is a good point to remember when selecting an inductor:
increased ripple current increases the FET conduction
losses, inductor core losses, and requires a larger output
capacitor to maintain a given amount of output ripple voltage. This means that a cheaper inductor (with less inducwww.national.com
16
switches and a different type with lower gate charge requirement for the other FET switch. However, for most applications this would give no measurable improvement.
(Continued)
Solid Tantalum capacitors are best in applications which
must operate over a wide temperature range. A good quality
Tantalum will typically exhibit less than 2:1 change in ESR
over the temperature range of +125˚C to −40˚C. Recommended types are Sprague 593D, Sprague 594D, and AVX
TPS series.
Selecting An Output Capacitor
The required value of output capacitance is directly related
to the specification for the maximum amount of output voltage ripple allowed in the application. Since ESR effects the
ripple voltage, it is important to have a guideline for ESR.
The maximum allowed ESR can be calculated as follows.
VRIPPLE = IRIPPLE *ESR(max)
CURRENT SENSE RESISTOR
A sense resistor is placed between the inductor and the
output capacitor to measure the inductor current. The value
of this resistor is set by the current limit voltage of the
LM2641 (see Electrical Characteristics) and the maximum
(peak) inductor current. The value of the sense resistor can
be calculated from:
Using V = Ldi/dt
VOUT = L *IRIPPLE/{(1−D)TS} = L *IRIPPLE *FS/(1−D)
IRIPPLE = VOUT*(1−D)/)L *FS)
Where:
VCL(MIN) is the minimum specified current limit voltage (see
Electrical Characteristics).
IMAX is the maximum output current for the application.
ESR(max) = VRIPPLE/IRIPPLE
IRIPPLE is the inductor ripple current for the application.
TOL is the tolerance (in %) of the sense resistor.
The physical placement of the sense resistors should be as
close as possible to the LM2641 to minimize the lead length
of the connections to the CSH and CSL pins. Keeping short
leads on these connections reduces the amount of switching
noise conducted into the current sense circuitry of the
LM2641.
A reasonable value for COUT can be obtained by choosing
capacitors with net ESR less than 1⁄2 of ESR(max).
Hence,
ESR(max) = VRIPPLE*L* FS/ {VOUT(1−D)}
The value of COUT necessary to meet the voltage ripple
specification can be found using the approximation:
EXTERNAL DIODES
FET Diodes
Both of the low-side MOSFET switches have an external
Schottky diode connected from drain to source. These diodes are electrically in parallel with the intrinsic body diode
present inside the FET. These diodes conduct during the
dead time when both FETs are off and the inductor current
must be supplied by the catch diode (which is either the body
diode or the Schottky diode).
Converter efficiency is improved by using external Schottky
diodes. Since they have much faster turn-off recovery than
the FET body diodes, switching losses are reduced.
The voltage rating of the Schottky must be at least 25%
higher than the maximum input voltage. The average current
rating of the diode needs to be only about 30% of the output
current, because the duty cycle is low.
The physical placement of the Schottky diode must be as
close as possible to the FET, since any parasitic (lead)
inductance in series with the Schottky will slow its turn-ON
and cause current to flow through the FET body diode.
Bootstrap Diodes
As shown in the block diagram for the LM2641, the CBOOT
pin has an internal diode which is connected to the 5V
internal rail (which is also connected to the LIN pin). This
diode charges up the bootstrap capacitor to about 5V when
the low-side FET switch turns ON and pulls its drain down to
ground. The internal diode works well until the pulse widths
get extremely narrow, and then the charge applied to the
bootstrap capacitor can become insufficient to fully turn ON
the gate of the FET.
For this reason, an external diode should be used which
connects directly between the bootstrap capacitor and the
external capacitor connected to the LIN pin (C17). A
fast-recovery silicon diode should be used which has an
average current rating ≥ 50 mA, with voltage rating > 30V.
Where:
IRIPPLE is the inductor ripple current.
VRIPPLE is the output ripple voltage.
ESR is the equivalent series resistance of the output capacitor.
F is the switching frequency, FS.
TS = 1/FS.
D = Duty Cycle.
The ESR term predominates in determining output ripple
voltage. Good quality Tantalum capacitors have guaranteed
maximum specifications for ESR, but the typical values for
ESR are usually considerably lower than the maximum limit.
POWER MOSFETs
Two N-channel logic-level MOSFETs are required for each
output. The voltage rating should be at least 1.2 times the
maximum input voltage.
Maximizing efficiency for a design requires selecting the right
FET. The ON-resistance of the FET determines the ON-state
(conduction) losses, while gate charge defines the losses
during switch transitions. These two parameters require a
trade-off, since reducing ON-resistance typically requires
increasing gate capacitance (which increases the charge
required to switch the FET). Improved FETs are currently
being released which are designed specifically for optimized
ON-resistance and gate charge characteristics.
The VIN and VOUT for a specific application determines the
ON time of each switch. In some cases where one FET is on
most of the time, efficiency may be improved slightly by
selecting a low ON-resistance FET for one of the FET
17
www.national.com
LM2641
Design Procedure
LM2641
Design Procedure
loaded, and an undervoltage (or overvoltage) condition is
detected. When this happens, the LM2641 turns off the
switching oscillator and turns on both of the low-side FET’s
which abruptly grounds one end of the inductor. When this
happens, the other end of the inductor (which is connected
to the regulated output) will experience a transient ringing
voltage as the energy stored in the inductor is discharged.
The amplitude and duration of the ringing is a function of the
R-L-C tank circuit made up the output capacitance, inductor,
and resistance of the inductor windings.
Because of this, the choice of inductor influences how large
in amplitude the ringing will be. In tests performed on the
Typical Application Circuit, the Sumida inductor showed less
ringing than the Pulse inductor, but both showed a voltage
transient that would go slightly below ground. For this reason, the output diodes are recommended.
(Continued)
Output Diodes
It is recommended that diodes be placed between the regulated outputs and ground to prevent the outputs from swinging below ground. The diode used may be a Schottky or
silicon type, and should have a current rating of 1A or more.
If the outputs are allowed to swing below ground more than
a Vbe, the substrate of the LM2641 will become forward
biased which will cause the part to operate incorrectly. Another potential problem which could be caused by negative
output transients is damage to the output capacitors, since
tantalum capacitors can be damaged if a reverse voltage is
forced across them
The operating conditions where this can occur are not typical: it can happen if one or both of the outputs are very lightly
www.national.com
18
LM2641 Dual Adjustable Step-Down Switching Power Supply Controller
Physical Dimensions
inches (millimeters)
unless otherwise noted
28-Lead TSSOP (MTC)
Order Number LM2641MTC-ADJ
NS Package Number MTC28
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.