NSC LMX2320

LMX2315/LMX2320/LMX2325 PLLatinum TM
Frequency Synthesizer
for RF Personal Communications
LMX2325 2.5 GHz
LMX2320 2.0 GHz
LMX2315 1.2 GHz
General Description
Features
The LMX2315/2320/2325’s are high performance frequency synthesizers with integrated prescalers designed for RF
operation up to 2.5 GHz. They are fabricated using National’s ABiC IV BiCMOS process.
A 64/65 or a 128/129 divide ratio can be selected for the
LMX2315 and LMX2320 RF synthesizer at input frequencies
of up to 1.2 GHz and 2.0 GHz, while 32/33 and 64/65 divide
ratios are available in the 2.5 GHz LMX2325. Using a proprietary digital phase locked loop technique, the LMX2315/
2320/2325’s linear phase detector characteristics can generate very stable, low noise signals for controlling a local
oscillator.
Serial data is transferred into the LMX2320 and the
LMX2325 via a three line MICROWIRETM interface (Data,
Enable, Clock). Supply voltage can range from 2.7V to 5.5V.
The LMX2315, LMX2320 and the LMX2325 feature very low
current consumption, typically 6 mA, 10 mA and 11 mA respectively.
The LMX2315, LMX2320 and the LMX2325 are available in
a TSSOP 20-pin surface mount plastic package.
Y
Y
Y
Y
Y
Y
Y
RF operation up to 2.5 GHz
2.7V to 5.5V operation
Low current consumption
Dual modulus prescaler:
LMX2325
32/33 or 64/65
LMX2320/LMX2315
64/65 or 128/129
Internal balanced, low leakage charge pump
Power down feature for sleep mode:
ICC e 30 mA (typ) at VCC e 3V
Small-outline, plastic, surface mount TSSOP, 0.173×
wide
Applications
Y
Y
Y
Y
Cellular telephone systems
(GSM, IS-54, IS-95, (RCR-27)
Portable wireless communications (DECT, PHS)
CATV
Other wireless communication systems
Block Diagram
TL/W/12339 – 1
TRI-STATEÉ is a registered trademark of National Semiconductor Corporation.
MICROWIRETM and PLLatinumTM are trademarks of National Semiconductor Corporation.
C1996 National Semiconductor Corporation
TL/W/12339
RRD-B30M106/Printed in U. S. A.
http://www.national.com
LMX2315/LMX2320/LMX2325 PLLatinum Frequency
Synthesizer for RF Personal Communications
LMX2325 2.5 GHz LMX2320 2.0 GHz LMX2315 1.2 GHz
September 1996
Connection Diagrams
LMX2315/LMX2320/LMX2325
TL/W/12339 – 2
20-Lead (0.173× Wide) Thin Shrink Small Outline Package (TM)
Order Number LMX2315TM, LMX2315TMX, LMX2325TM, LMX2325TMX, LMX2320TM or LMX2320TMX
See NS Package Number MTC20
Pin Descriptions
Pin No.
I/O
Description
1
OSCIN
Pin Name
I
Oscillator input. A CMOS inverting gate input intended for connection to a crystal resonator for
operation as an oscillator. The input has a VCC/2 input threshold and can be driven from an external
CMOS or TTL logic gate. May also be used as a buffer for an externally provided reference oscillator.
3
OSCOUT
O
Oscillator output.
4
VP
Power supply for charge pump. Must be t VCC.
5
VCC
Power supply voltage input. Input may range from 2.7V to 5.5V. Bypass capacitors should be placed
as close as possible to this pin and be connected directly to the ground plane.
6
Do
7
GND
8
LD
O
Lock detect. Output provided to indicate when the VCO frequency is in ‘‘lock’’. When the loop is
locked, the pin’s output is HIGH with narrow low pulses.
10
fIN
I
Prescaler input. Small signal input from the VCO.
11
CLOCK
I
High impedance CMOS Clock input. Data is clocked in on the rising edge, into the various counters
and registers.
13
DATA
I
Binary serial data input. Data entered MSB first. LSB is control bit. High impedance CMOS input.
14
LE
I
Load enable input (with internal pull-up resistor). When LE transitions HIGH, data stored in the shift
registers is loaded into the appropriate latch (control bit dependent). Clock must be low when LE
toggles high or low. See Serial Data Input Timing Diagram.
15
FC
I
Phase control select (with internal pull-up resistor). When FC is LOW, the polarity of the phase
comparator and charge pump combination is reversed.
16
BISW
O
Analog switch output. When LE is HIGH, the analog switch is ON, routing the internal charge pump
output through BISW (as well as through Do).
17
fOUT
O
Monitor pin of phase comparator input. CMOS output.
18
wp
O
Output for external charge pump. wp is an open drain N-channel transistor and requires a pull-up
resistor.
19
PWDN
I
Power Down (with internal pull-up resistor).
PWDN e HIGH for normal operation.
PWDN e LOW for power saving.
Power down function is gated by the return of the charge pump to a TRI-STATEÉ condition.
20
wr
O
Output for external charge pump. wr is a CMOS logic output.
2,9,12
NC
http://www.national.com
O
Internal charge pump output. For connection to a loop filter for driving the input of an external VCO.
Ground.
No connect.
2
Functional Block Diagram
TL/W/12339 – 3
Note 1: The prescalar for the LMX2315 and LMX2320 is either 64/65 or 128/129, while the prescalar for the LMX2325 is 32/33 or 64/65.
Note 2: The power down function is gated by the charge pump to prevent unwanted frequency jumps. Once the power down pin is brought low the part will go into
power down mode when the charge pump reaches a TRI-STATE condition.
3
http://www.national.com
Absolute Maximum Ratings (Notes 1, 2)
Recommended Operating
Conditions
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
Power Supply Voltage
VCC
VP
b 0.3V to a 6.5V
b 0.3V to a 6.5V
Voltage on Any Pin
with GND e 0V (VI)
b 0.3V to a 6.5V
Storage Temperature Range (TS)
Lead Temperature (TL) (solder, 4 sec.)
Power Supply Voltage
VCC
VP
2.7V to 5.5V
VCC to a 5.5V
b 40§ C to a 85§ C
Operating Temperature (TA)
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to
the device may occur. Operating Ratings indicate conditions for which the
device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test
conditions listed.
b 65§ C to a 150§ C
a 260§ C
Note 2: This device is a high performance RF integrated circuit with an ESD
rating k 2 kV and is ESD sensitive. Handling and assembly of this device
should be done at ESD workstations.
Electrical Characteristics
LMX2325 and LMX2320 VCC e VP e 3.0V; LMX2315 VCC e VP e 5.0V; b40§ C k TA k 85§ C, except as specified
Symbol
ICC
ICC-PWDN
fIN
fOSC
fw
PfIN
Parameter
Power Supply Current
Typ
Max
Units
VCC e 3.0V
Conditions
6.0
8.0
mA
VCC e 5.0V
6.5
8.5
mA
LMX2320
VCC e 3.0V
10
13.5
mA
LMX2325
VCC e 3.0V
11
15
mA
VCC e 3.0V
30
180
mA
VCC e 5.0V
60
350
mA
LMX2315
Power Down Current
Maximum Operating Frequency
Min
LMX2315
1.2
LMX2320
2.0
LMX2325
2.5
Oscillator Frequency
5
20
MHz
No Load on OSCout
5
40
MHz
VCC e 2.7V to 3.3V
b 15
a6
VCC e 3.3V to 5.5V
b 10
a6
Phase Detector Frequency
Input Sensitivity
10
VOSC
Oscillator Sensitivity
OSCIN
VIH
High-Level Input Voltage
*
VIL
Low-Level Input Voltage
*
IIH
High-Level Input Current (Clock, Data)
VIH e VCC e 5.5V
b 1.0
IIL
Low-Level Input Current (Clock, Data)
VIL e 0V, VCC e 5.5V
b 1.0
IIH
Oscillator Input Current
VIH e VCC e 5.5V
IIL
GHz
MHz
dBm
0.5
VPP
0.7 VCC
V
VIL e 0V, VCC e 5.5V
b 100
0.3 VCC
V
1.0
mA
1.0
mA
100
mA
mA
IIH
High-Level Input Current (LE, FC)
VIH e VCC e 5.5V
b 1.0
1.0
mA
IIL
Low-Level Input Current (LE, FC)
VIL e 0V, VCC e 5.5V
b 100
1.0
mA
*Except fIN and OSCIN
http://www.national.com
4
Electrical CharacteristicsLMX2325 and LMX2320 VCC e VP e 3.0V; LMX2315 VCC e VP e 5.0V; b40§ C k
TA k 85§ C, except as specified (Continued)
Symbol
IDo-source
Parameter
Charge Pump Output Current
IDo-sink
IDo-source
Charge Pump Output Current
IDo-sink
Conditions
Min
Typ
Max
Units
VCC e VP e 3.0V, VDo e VP/2
b 2.5
mA
VCC e VP e 3.0V, VDo e VP/2
2.5
mA
VCC e VP e 5.0V, VDo e VP/2
b 5.0
mA
VCC e VP e 5.0V, VDo e VP/2
5.0
mA
IDo-Tri
Charge Pump TRI-STATEÉ Current
0.5V s VDo s VP b 0.5V
T e 85§ C
IDo vs VDo
Charge Pump Output Current
Magnitude Variation vs Voltage
(Note 1)
IDo-sink vs
IDo-source
IDovs T
2.5
nA
0.5V s VDo s VP b 0.5V
T e 25§ C
15
%
Charge Pump Output Current
Sink vs Source Mismatch
(Note 2)
VDo e VP/2
T e 25§ C
10
%
Charge Pump Output Current
Magnitude Variation vs Temperature
(Note 3)
b 40§ C k T k 85§ C
VDo e VP/2
High-Level Output Voltage
IOH e b1.0 mA**
VOL
Low-Level Output Voltage
IOL e 1.0 mA**
VOH
High-Level Output Voltage (OSCOUT)
IOH e b200 mA
VOL
Low-Level Output Voltage (OSCOUT)
IOL e 200 mA
IOL
Open Drain Output Current (wp)
VCC e 5.0V, VOL e 0.4V
IOH
Open Drain Output Current (wp)
VOH e 5.5V
RON
Analog Switch ON Resistance (2315)
tCS
Data to Clock Set Up Time
See Data Input Timing
50
ns
tCH
Data to Clock Hold Time
See Data Input Timing
10
ns
tCWH
Clock Pulse Width High
See Data Input Timing
50
ns
tCWL
Clock Pulse Width Low
See Data Input Timing
50
ns
tES
Clock to Enable Set Up Time
See Data Input Timing
50
ns
tEW
Enable Pulse Width
See Data Input Timing
50
ns
VOH
b 2.5
10
%
VCC b 0.8
V
0.4
VCC b 0.8
V
V
0.4
1.0
V
mA
100
100
mA
X
**Except OSCOUT
Notes 1, 2, 3: See related equations in Charge Pump Current Specification Definitions
5
http://www.national.com
Typical Performance Characteristics
ICC vs VCC LMX2320/25
ICC vs VCC LMX2315
TL/W/12339–4
TL/W/12339 – 51
Charge Pump Current vs Do Voltage
Charge Pump Current vs Do Voltage
TL/W/12339–40
TL/W/12339 – 7
Charge Pump Current Variation
Sink vs Source Mismatch vs Do Voltage
TL/W/12339–8
http://www.national.com
TL/W/12339 – 9
6
Typical Performance Characteristics
(Continued)
IDo TRI-STATE vs Do Voltage
Oscillator Input Sensitivity
TL/W/12339 – 14
TL/W/12339 – 5
LMX2320/25 Input Sensitivity vs Frequency
LMX2320/25 Input Sensitivity vs Frequency
TL/W/12339 – 10
TL/W/12339 – 11
LMX2315 Input Sensitivity vs Frequency
LMX2315 Input Sensitivity vs Frequency
TL/W/12339 – 41
TL/W/12339 – 42
7
http://www.national.com
Typical Performance Characteristics
(Continued)
LMX2320/25 Input Sensitivity at
Temperature Variation, VCC e 3V
LMX2320/25 Input Sensitivity at
Temperature Variation, VCC e 5V
TL/W/12339–12
TL/W/12339 – 13
LMX2315 Input Sensitivity at
Temperature Variation, VCC e 5V
LMX2315 Input Sensitivity at
Temperature Variation, VCC e 3V
TL/W/12339–43
TL/W/12339 – 44
LMX2315 Input Impedance vs Frequency
VCC e 2.7V to 5.5V, fIN e 100 MHz to 1,600 MHz
LMX2320/25 Input Impedance vs Frequency
VCC e 2.7V to 5.5V, fIN e 500 MHz to 3000 MHz
TL/W/12339–45
Marker
Marker
Marker
Marker
1
2
3
4
e
e
e
e
TL/W/12339 – 15
500 MHz, Real e 69, Imag. e b 330
900 MHz, Real e 36, Imag. e b 193
1 GHz, Real e 35, Imag. e b 172
1,500 MHz, Real e 30, Imag. e b 106
http://www.national.com
1
2
3
4
8
e
e
e
e
1.5
1.8
2.0
2.5
GHz,
GHz,
GHz,
GHz,
Real
Real
Real
Real
e
e
e
e
48,
44,
42,
36,
Im
Im
Im
Im
e
e
e
e
b 128
b 102
b 90
b 72
Charge Pump Current Specification Definitions
TL/W/12339 – 16
I1 e CP sink current at VDo e VP b DV
I4 e CP source current at VDo e VP b DV
I2 e CP sink current at VDo e VP/2
I5 e CP source current at VDo e VP/2
I3 e CP sink current at VDo e DV
I6 e CP source current at VDo e DV
DV e Voltage offset from positive and negative rails. Dependent on VCO tuning range relative to VCC and ground. Typical values are between 0.5V and 1.0V.
1. IDo vs VDo e Charge Pump Output Current magnitude variation vs Voltage e
[(/2 * l I1 l b l I3 l ]/[(/2 * À l I1 l a l I3 l Ó ] * 100% and [(/2 * l I4 l b l I6 l ]/[(/2 * À l I4 l a l I6 l Ó ] * 100%
2. IDo-sink vs IDo-source e Charge Pump Output Current Sink vs Source Mismatch e
[ l I2 l b l I5 l ]/[(/2 * À l I2 l a l I5 l Ó ] * 100%
3. IDo vs TA e Charge Pump Output Current magnitude variation vs Temperature e
[ l I2 @ temp l b l I2 @ 25§ C l ]/ l I2 @ 25§ C l * 100% and [ l I5 @ temp l b l I5 @ 25§ C l ]/ l I5
4. Kw e
@
25§ C l * 100%
Phase detector/charge pump gain constant e
(/2 * À l I2 l a l I5 l Ó
RF Sensitivity Test Block Diagram
TL/W/12339 – 17
Note 1: N e 10,000
R e 50
P e 64
Note 2: Sensitivity limit is reached when the error of the divided RF output, fOUT, is greater than or equal to 1 Hz.
9
http://www.national.com
Functional Description
The simplified block diagram below shows the 19-bit data register, the 14-bit R Counter and the S Latch, and the 18-bit
N Counter (intermediate latches are not shown). The data stream is clocked (on the rising edge) into the DATA input, MSB first.
If the Control Bit (last bit input) is HIGH, the DATA is transferred into the R Counter (programmable reference divider) and the
S Latch (prescaler select: LMX2315 and LMX2320: 64/65 or 128/129; LMX2325 32/33 or 64/65). If the Control Bit (LSB) is
LOW, the DATA is transferred into the N Counter (programmable divider).
TL/W/12339 – 18
PROGRAMMABLE REFERENCE DIVIDER (R COUNTER) AND PRESCALER SELECT (S LATCH)
If the Control Bit (last bit shifted into the Data Register) is HIGH, data is transferred from the 19-bit shift register into a 14-bit
latch (which sets the 14-bit R Counter) and the 1-bit S Latch (S15, which sets the prescaler: 64/65 or 128/129 for the
LMX2315/20 or 32/33 or 64/65 for the LMX2325). Serial data format is shown below.
TL/W/12339 – 6
14-BIT PROGRAMMABLE REFERENCE DIVIDER RATIO
(R COUNTER)
Divide
S S S S S S S S S S S S S S
Ratio
14 13 12 11 10 9 8 7 6 5 4 3 2 1
R
3
0
0
0
0
0
0 0 0 0 0 0 0 1 1
4
0
0
0
0
0
0 0 0 0 0 0 1 0 0
#
#
#
#
#
#
# # # # # # # # #
16383
1
1
1
1
1
1 1 1 1 1 1 1 1 1
Notes: Divide ratios less than 3 are prohibited.
Divide ratio: 3 to 16383
S1 to S14: These bits select the divide ratio of the programmable
reference divider.
C: Control bit (set to HIGH level to load R counter and S Latch)
Data is shifted in MSB first.
http://www.national.com
10
Prescaler Select
LMX2315/20
LMX2325
S
15
128/129
64/65
0
64/65
32/33
1
Functional Description (Continued)
PROGRAMMABLE DIVIDER (N COUNTER)
The N counter consists of the 7-bit swallow counter (A counter) and the 11-bit programmable counter (B counter). If the Control
Bit (last bit shifted into the Data Register) is LOW, data is transferred from the 19-bit shift register into a 7-bit latch (which sets
the 7-bit Swallow (A) Counter) and an 11-bit latch (which sets the 11-bit programmable (B) Counter). Serial data format is shown
below.
TL/W/12339 – 20
Note: S8 to S18: Programmable counter divide ratio control bits (3 to 2047)
7-BIT SWALLOW COUNTER DIVIDE RATIO
(A COUNTER)
11-BIT PROGRAMMABLE COUNTER DIVIDE RATIO
(B COUNTER)
Divide
Ratio
A
S
7
S
6
S
5
S
4
S
3
S
2
S
1
Divide
Ratio
B
S
18
S
17
S
16
S
15
S
14
S
13
S
12
S
11
S
10
S
9
S
8
0
0
0
0
0
0
0
0
3
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
1
4
0
0
0
0
0
0
0
0
1
0
0
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
127
1
1
1
1
1
1
1
2047
1
1
1
1
1
1
1
1
1
1
1
Note: Divide ratio: 0 to 127
Note: Divide ratio: 3 to 2047 (Divide ratios less than 3 are prohibited)
BtA
BtA
PULSE SWALLOW FUNCTION
fVCO e [(P c B) a A] c fOSC/R
fVCO: Output frequency of external voltage controlled oscillator (VCO)
B:
Preset divide ratio of binary 11-bit programmable
counter (3 to 2047)
A:
Preset divide ratio of binary 7-bit swallow counter
(0 s A s 127, A s B)
fOSC: Output frequency of the external reference frequency
oscillator
R:
Preset divide ratio of binary 14-bit programmable reference counter (3 to 16383)
P:
Preset modulus of dual moduIus prescaler (64 or 128
for 2315/20 or 32 or 64 for 2325)
11
http://www.national.com
Functional Description (Continued)
SERIAL DATA INPUT TIMING
TL/W/12339 – 21
Notes: Parenthesis data indicates programmable reference divider data.
Data shifted into register on clock rising edge.
Data is shifted in MSB first.
Test Conditions: The Serial Data Input Timing is tested using a symmetrical waveform around VCC/2. The test waveform has an edge rate of 0.6 V/ns with
amplitudes of 2.2V @ VCC e 2.7V and 2.6V @ VCC e 5.5V.
Phase Characteristics
In normal operation, the FC pin is used to reverse the polarity of the phase detector. Both the internal and any external
charge pump are affected.
Depending upon VCO characteristics, FC pin should be set
accordingly:
When VCO characteristics are like (1), FC should be set
HIGH or OPEN CIRCUIT;
When VCO characteristics are like (2), FC should be set
LOW.
When FC is set HIGH or OPEN CIRCUIT, the monitor pin of
the phase comparator input, fout, is set to the reference
divider output, fr. When FC is set LOW, fout is set to the
programmable divider output, fp.
VCO Characteristics
TL/W/12339 – 22
PHASE COMPARATOR AND INTERNAL CHARGE PUMP CHARACTERISTICS
TL/W/12339 – 23
Notes: Phase difference detection range: b 2q to a 2q
The minimum width pump up and pump down current pulses occur at the Do pin when the loop is locked.
FC e HIGH
http://www.national.com
12
Analog Switch
The analog switch is useful for radio systems that utilize a frequency scanning mode and a narrow band mode. The purpose of
the analog switch is to decrease the loop filter time constant, allowing the VCO to adjust to its new frequency in a shorter
amount of time. This is achieved by adding another filter stage in parallel. The output of the charge pump is normally through the
Do pin, but when LE is set HIGH, the charge pump output also becomes available at BISW. A typical circuit is shown below. The
second filter stage (LPF-2) is effective only when the switch is closed (in the scanning mode).
TL/W/12339 – 24
Typical Crystal Oscillator Circuit
Typical Lock Detect Circuit
A typical circuit which can be used to implement a crystal
oscillator is shown below.
A lock detect circuit is needed in order to provide a steady
LOW signal when the PLL is in the locked state. A typical
circuit is shown below.
TL/W/12339 – 52
TL/W/12339 – 26
13
http://www.national.com
Typical Application Example
Operational Notes:
*
**
TL/W/12339 – 27
VCO is assumed AC coupled.
RIN increases impedance so that VCO output power is provided to the load rather than the PLL. Typical values are 10X to 200X depending on the VCO power
level. fIN RF impedance ranges from 40X to 100X.
*** 50X termination is often used on test boards to allow use of external reference oscillator. For most typical products a CMOS clock is used and no terminating
resistor is required. OSCIN may be AC or DC coupled. AC coupling is recommended because the input circuit provides its own bias. (See Figure below)
Layout Hints:
TL/W/12339 – 28
Proper use of grounds and bypass capacitors is essential to achieve a high level of performance.
Crosstalk between pins can be reduced by careful board layout.
This is a static sensitive device. It should be handled only at static free work stations.
http://www.national.com
14
Application Information
LOOP FILTER DESIGN
A block diagram of the basic phase locked loop is shown.
TL/W/12339 – 29
FIGURE 1. Basic Charge Pump Phase Locked Loop
An example of a passive loop filter configuration, including
the transfer function of the loop filter, is shown in Figure 2 .
TL/W/12339 – 30
s (C2 # R2) a 1
Z(s) e
s2 (C1 # C2 # R2) a sC1 a sC2
TL/W/12339 – 31
FIGURE 2. 2nd Order Passive Filter
Define the time constants which determine the pole and
zero frequencies of the filter transfer function by letting
(1a)
T2 e R2 # C2
and
C1 # C2
T1 e R2 #
C1 a C2
(1b)
The PLL linear model control circuit is shown along with the
open loop transfer function in Figure 3 . Using the phase
detector and VCO gain constants [Kw and KVCO] and the
loop filter transfer function [Z(s)], the open loop Bode plot
can be calculated. The loop bandwidth is shown on the
Bode plot (0p) as the point of unity gain. The phase margin
is shown to be the difference between the phase at the unity
gain point and b180§ .
FIGURE 3. Open Loop Transfer Function
Thus we can calculate the 3rd order PLL Open Loop Gain in
terms of frequency
G(s) # H(s)ls e j # 0 e
# KVCO (1 a j0 # T2) T1
#
02C1 # N(1 a j0 # T1)
T2
b Kw
(2)
From equation 2 we can see that the phase term will be
dependent on the single pole and zero such that
w(0) e tanb1 (0 # T2) b tanb1 (0 # T1) a 180§ (3)
By setting
T2
T1
dw
e
b
e0
d0
1 a (0 # T2)2 1 a (0 # T1)2
(4)
we find the frequency point corresponding to the phase inflection point in terms of the filter time constants T1 and T2.
This relationship is given in equation 5.
0p e 1/0T2 # T1
(5)
For the loop to be stable the unity gain point must occur
before the phase reaches b180 degrees. We therefore
want the phase margin to be at a maximum when the magnitude of the open loop gain equals 1. Equation 2 then gives
C1 e
TL/W/12339 – 32
Open Loop Gain e ii/ie e H(s) G(s)
e Kw Z(s) KVCO/Ns
Closed Loop Gain e io/ii e G(s)/[1 a H(s) G(s)]
15
Kw # KVCO # T1 (1 a j0p # T2)
0p2 # N # T2 (1 a j0p # T1)
Ó
Ó
(6)
http://www.national.com
Application Information (Continued)
Therefore, if we specify the loop bandwidth, 0p, and the
phase margin, wp, Equations 1 through 6 allow us to calculate the two time constants, T1 and T2, as shown in equations 7 and 8. A common rule of thumb is to begin your
design with a 45§ phase margin.
secwp b tanwp
T1 e
0p
(7)
T2 e
In choosing the loop filter components a trade off must be
made between lock time, noise, stability, and reference
spurs. The greater the loop bandwidth the faster the lock
time will be, but a large loop bandwidth could result in higher
reference spurs. Wider loop bandwidths generally improve
close in phase noise but may increase integrated phase
noise depending on the reference input, VCO and division
ratios used. The reference spurs can be reduced by reducing the loop bandwidth or by adding more low pass filter
stages but the lock time will increase and stability will decrease as a result.
1
0p2 # T1
(8)
From the time constants T1, and T2, and the loop bandwidth, 0p, the values for C1, R2, and C2 are obtained in
equations 9 to 11.
THIRD ORDER FILTER
A low pass filter section may be needed for some applications that require additional rejection of the reference sidebands, or spurs. This configuration is given in Figure 4 . In
order to compensate for the added low pass section, the
component values are recalculated using the new open
loop unity gain frequency. The degradation of phase margin
caused by the added low pass is then mitigated by slightly
increasing C1 and C2 while slightly decreasing R2.
The added attenuation from the low pass filter is:
ATTEN e 20 log[(2qfref # R3 # C3)2 a 1]
(12)
T1 Kw # KVCO 1 a (0p # T2)2
#
T2
0p2 # N
1 a (0p # T1)2
(9)
T2
b1
C2 e C1 #
T1
(10)
T2
R2 e
C2
(11)
Voltage Controlled Oscillator (VCO)
KVCO (MHz/V)
Tuning Voltage constant. The frequency vs voltage tuning ratio.
Kw (mA)
Phase detector/charge pump gain
constant. The ratio of the current output to the input phase differential.
N
Main divider ratio. Equal to RFopt/fref
C1 e
#
0
J
RFopt (MHz)
Radio Frequency output of the VCO at
which the loop filter is optimized.
fref (kHz)
Frequency of the phase detector inputs. Usually equivalent to the RF
channel spacing.
T2 e
Defining the additional time constant as
T3 e R3 # C3
(13)
Then in terms of the attenuation of the reference spurs added by the low pass pole we have
0
10ATTEN/20 b 1
(14)
(2q # fref)2
We then use the calculated value for loop bandwidth 0c in
equation 11, to determine the loop filter component values
in equations 15 – 17. 0c is slightly less than 0p, therefore
the frequency jump lock time will increase.
T3 e
1
0c2 # (T1 a T3)
(15)
(T1 a T3)2 a T1 # T3
b1
[tanw # (T1 a T3)] 2
0c e
tanw # (T1 a T3)
#
[(T1 a T3)2 a T1 # T3]
C1 e
(/2
T1 Kw # KVCO
(1 a 0c2 # T22)
#
#
T2
0c2 # N
(1 a 0c2 # T12) (1 a 0c2 # T32)
http://www.national.com
Ð01
a
Ð
(
16
(
(16)
(17)
Application Information (Continued)
Consider the following application examples:
Example Ý1
KVCO e 20 MHz/V
Kw e 5 mA (Note 1)
RFopt e 900 MHz
Fref e 200 kHz
N e RFopt/fref e 4500
0p e 2q * 20 kHz e 1.256e5
wp e 45§
ATTEN e 20 dB
T1 e
secwp b tanwp
0p
e 3.29e b 6
T3 e
0(2q # 200e3)
0c e
(3.29eb6 a 2.387eb6)
[(3.29eb6 a 2.387eb6)2 a 3.29eb6 # 2.387eb6]
10(20/20) b 1
2
#
Ð01
a
e 2.387e b 6
(3.29eb6 a 2.387eb6)2 a 3.29eb6 # 2.387eb6
b1
[(3.29eb6 a 2.387eb6)] 2
(
e 7.045e4
T2 e
1
e 3.549e b 5
(7.045e4)2 # (3.29eb6 a 2.387eb6)
(/2
[1 a (7.045e4)2 # (3.549eb5)2]
3.29eb6 (5eb3) # 20e6
#
[1 a (7.045e4)2 # (3.29eb6)2] [1 a (7.045e4)2 # (2.387eb6)2]
3.549eb5 (7.045e4)2 # 4500
e 1.085 nF
Ð
C1 e
C2 e 1.085 nF #
R2 e
# 3.29e
3.55eb5
b1
b6
J
(
e 10.6 nF;
3.55eb5
e 3.35 kX;
10.6eb9
if we choose R3 e 22k; then C3 e
2.34eb6
e 106 pF.
22e3
Converting to standard component values gives the following filter values, which are shown in Figure 4 .
C1 e 1000 pF
R2 e 3.3 kX
C2 e 10 nF
R3 e 22 kX
C3 e 100 pF
TL/W/12339 – 46
Note 1: See related equation for Kw in Charge Pump Current Specification
Definitions. For this example VP e 5.0V. The value of Kw can then
be approximated using the curves in the Typical Peformance Characteristics for Charge Pump Current vs. Do Voltage. The units for
Kw are in mA. You may also use Kw e (5 mA/2q rad), but in this
case you must convert KVCO to (rad/V) multiplying by 2q.
FIGURE 4. E 20 kHz Loop Filter
17
http://www.national.com
Application Information (Continued)
MEASUREMENT RESULTS (Example Ý1)
TL/W/12339–47
TL/W/12339 – 48
FIGURE 5. PLL Reference Spurs
The reference spurious level is k b74 dBc, due to the loop
filter attenuation and the low spurious noise level of the
LMX2315.
FIGURE 7. PLL Phase Noise @ 1 kHz Offset
The phase noise level at 1 kHz offset is b79.5 dBc/Hz.
TL/W/12339–49
FIGURE 6. PLL Phase Noise 10 kHz Offset
The phase noise level at 10 kHz offset is b80 dBc/Hz.
TL/W/12339 – 50
FIGURE 8. Frequency Jump Lock Time
Of concern in any PLL loop filter design is the time it takes
to lock in to a new frequency when switching channels. Figure 8 shows the switching waveforms for a frequency jump
of 865 MHz to 915 MHz. By narrowing the frequency span
of the HP53310A Modulation Domain Analyzer enables
evaluation of the frequency lock time to within g 500 Hz.
The lock time is seen to be less than 500 ms for a frequency
jump of 50 MHz.
http://www.national.com
18
Application Information (Continued)
Example Ý2
KVCO e 34 MHz/V
Kw e 2.8 mA (Note 1)
RFopt e 1665 MHz
Fref e 300 kHz
N e RFopt/fref e 5550
0p e 2q * 20 kHz e 1.256e5
wp e 43
ATTEN e 12 dB
T1 e
secw b tanw
0p
e 3.462e b 6
T3 e
0(2q # 300e3)
0c e
tan43 (3.862eb6 a 9.16eb7)
(3.462eb6 a 9.16eb7)2 a 3.462eb6 # 9.16eb7)
10(12/20) b 1
2
#
Ð01
a
e 9.16e b 7
(3.462eb6 a 9.16eb7)2 a 3.462eb6 # 9.16eb7
b1
[tan43 (3.462eb6 a 9.16eb7)] 2
(
1
e 2.437e b 5
T2 e
(9.682e4)2 (3.462eb6 a 9.16eb7)
(/2
[1 a (9.682e4)2 # (2.437eb5)2]
3.462eb6 (2.8eb3) # 34e6
#
[1 a (9.682e4)2 (3.462eb6)2] [1 a (9.682e4)2 # (9.16eb7)2]
2.437eb5 (9.682e4)2 # 5550
e 0.63 nF
Ð
C1 e
C2 e 0.63 nF
R2 e
# 3.402e
2.437eb5
b1
b6
J
(
e 3.88 nF;
2.437eb5
e 6.28 kX;
3.88eb9
if we choose R3 e 27k; then C3 e
9.16eb7
e 34 pF.
27e3
Converting to standard component values gives the following filter values, which are shown in Figure 4 .
C1 e 560 pF
R2 e 6.8 kX
C2 e 2700 pF
R3 e 27 kX
C3 e 56 pF
TL/W/12339 – 33
Note 1: See related equation for Kw in Charge Pump Current Specification
Definitions. For this example VP e 3.3V. The value for Kw can then
be approximated using the curves in the Typical Performance Characteristics for Charge Pump Current vs. Do Voltage. The units for
Kw are in mA. You may also use Kw e (2.8 mA/2q rad), but in this
case you must convert KVCO to (rad/V) multiplying by 2q.
FIGURE 9. E 20 kHz Loop Filter
19
http://www.national.com
Application Information (Continued)
MEASUREMENT RESULTS (Example Ý2)
TL/W/12339 – 34
TL/W/12339 – 35
FIGURE 10. PLL Reference Spurs
The reference spurious level is k b65 dBc, due to the loop
filter attenuation and the low spurious noise level of the
LMX2320.
FIGURE 11. PLL Phase Noise @ 150 Hz Offset
The phase noise level at 150 Hz offset is b81.1 dBc/Hz.
The spurs at 60 and 180 Hz offset are due to 60 Hz line
noise from the power supply.
TL/W/12339 – 36
FIGURE 12. PLL Phase Noise 20 kHz Offset
The phase noise level at 20 kHz offset is b80 dBc/Hz.
TL/W/12339 – 37
FIGURE 13. Frequency Jump Lock Time
Of concern in any PLL loop filter design is the time it takes
to lock in to a new frequency when switching channels. Figure 13 shows the switching waveforms for a frequency jump
of 1650.9 MHz to 1683.9 MHz. By narrowing the frequency
span of the HP53310A Modulation Domain Analyzer enables evaluation of the frequency lock time to within
g 1 kHz. The lock time is seen to be less than 500 ms for a
frequency jump of 33 MHz.
http://www.national.com
20
Application Information (Continued)
EXAMPLE
EXTERNAL CHARGE PUMP
The LMX PLLatinum series of frequency synthesizers are
equipped with an internal balanced charge pump as well as
outputs for driving an external charge pump. Although the
superior performance of NSC’s on board charge pump eliminates the need for an external charge pump in most applications, certain system requirements are more stringent. In
these cases, using an external charge pump allows the designer to take direct control of such parameters as charge
pump voltage swing, current magnitude, TRI-STATE leakage, and temperature compensation.
One possible architecture for an external charge pump current source is shown in Figure 14 . The signals wp and wr in
the diagram, correspond to the phase detector outputs of
the 2315/20/25 frequency synthesizers. These logic signals are converted into current pulses, using the circuitry
shown in Figure 14 , to enable either charging or discharging
of the loop filter components to control the output frequency
of the PLL.
Referring to Figure 14 , the design goal is to generate a
5 mA current which is relatively constant to within 5V of the
power supply rail. To accomplish this, it is important to establish as large of a voltage drop across R5, R8 as possible
without saturating Q2, Q4. A voltage of approximately
300 mV provides a good compromise. This allows the current source reference being generated to be relatively repeatable in the absence of good Q1, Q2/Q3, Q4 matching.
(Matched transistor pairs is recommended.) The wp and wr
outputs are rated for a maximum output load current of
1 mA while 5 mA current sources are desired. The voltages
developed across R4, 9 will consequently be approximately
258 mV, or 42 mV less than R8, 5, due to the current density
differences À0.026*1n (5 mA/1 mA)Ó through the Q1,
Q2/Q3, Q4 pairs.
In order to calculate the value of R7 it is necessary to first
estimate the forward base to emitter voltage drop (Vfn,p) of
the transistors used, the VOL drop of wp, and the VOH drop
of wr’s under 1 mA loads. (wp’s VOL k 0.1V and (wr,s VOH
k 0.1V).
Knowing these parameters along with the desired current
allow us to design a simple external charge pump. Separating the pump up and pump down circuits facilitates the nodal analysis and give the following equations.
#
isource
VR5 b VT # 1n
ip max
R4 e
isource
VR8 b VT # 1n
R9 e
isink
#i
isink
n max
Typical Device Parameters
bn e 100, bp e 50
Typical System Parameters
VP e 5.0V;
Vcntl e 0.5V – 4.5V;
Vwp e 0.0V, Vwr e 5.0V
ISINK e ISOURCE e 5.0 mA;
Vfn e Vfp e 0.8V
Irmax e Ipmax e 1 mA
VR8 e VR5 e 0.3V
VOLwp e VOHwp e 100 mV
Design Parameters
TL/W/12339 – 39
FIGURE 14
Therefore select
R4 e R9 e
J
0.3V b 0.026 # 1n(5.0 mA/1.0 mA)
e 51.6X
5 mA
R5 e
0.3V # (50 a 1)
e 332X
1.0 mA # (50 a 1) b 5.0 mA
R8 e
0.3V # (100 a 1)
e 315.6X
1.0 mA # (100 a 1) b 5.0 mA
R6 e R7 e
(5V b 0.1V) b (0.3V a 0.8V)
e 3.8 kX
1.0 mA
J
R5 e
VR5 # (bp a 1)
ip max # (bp a 1) b isource
R8 e
VR8 # (bn a 1)
ir max # (bn a 1) isink
R6 e
(Vp b VVOLwp) b (VR5 a Vfp)
ip max
R7 e
(VP b VVOHwp) b (VR8 a Vfn)
imax
21
http://www.national.com
LMX2315/LMX2320/LMX2325 PLLatinum Frequency
Synthesizer for RF Personal Communications
LMX2325 2.5 GHz LMX2320 2.0 GHz LMX2315 1.2 GHz
Physical Dimensions millimeters
NS Package Number MTC20
20-Lead (0.173× Wide) Thin Shrink Small Outline Package (TM)
Order Number LMX2315TM, LMX2320TM or LMX2325TM
For Tape and Reel Order Number LMX2315TMX, LMX2320TMX or LMX2325TMX (2500 Units per Reel)
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and whose
failure to perform, when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
National Semiconductor
Corporation
1111 West Bardin Road
Arlington, TX 76017
Tel: 1(800) 272-9959
Fax: 1(800) 737-7018
http://www.national.com
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
National Semiconductor
Europe
Fax: a49 (0) 180-530 85 86
Email: europe.support @ nsc.com
Deutsch Tel: a49 (0) 180-530 85 85
English Tel: a49 (0) 180-532 78 32
Fran3ais Tel: a49 (0) 180-532 93 58
Italiano Tel: a49 (0) 180-534 16 80
National Semiconductor
Hong Kong Ltd.
13th Floor, Straight Block,
Ocean Centre, 5 Canton Rd.
Tsimshatsui, Kowloon
Hong Kong
Tel: (852) 2737-1600
Fax: (852) 2736-9960
National Semiconductor
Japan Ltd.
Tel: 81-043-299-2308
Fax: 81-043-299-2408
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.