HYBRID IC VLA312-2425 ISOLATED TYPE DC-DC CONVERTER DESCRIPTION The VLA312-2425 is an isolated DC-DC converter designed to control the industrial equipment. It can input the rectified AC480V (DC850Vmax) directly and convert to low voltage. Total output power is 25W. FEATURES •Input ------------ 475V to 850V DC •Output----------- +24V, 1.05A (25.2W) •Electrical isolation (between input and output) ------------- 2500Vrms 1 minute •Over current protection (auto resumption) •Over voltage protection APPLICATIONS On-board pre-regulator for industrial control equipment BLOCK DIAGRAM +VIN +Vo RECTIFIER -Vo CURRENT SENSING -VIN GATE CONTROL POWER POWER HIGH SIDE DRIVE LOW SIDE DRIVE MAIN CONTROL FG HYBRID IC VLA312-2425 ISOLATED TYPE DC-DC CONVERTER MAXIMUM RATINGS (unless otherwise noted, Ta=25°C) Symbol Parameter Conditions Ratings Unit VIN Input voltage - 850 V IO Output current - 1.05 A Topr Operating temperature -10 ~ +55 °C Tstg Storage temperature No condensation -20 ~ +75 °C Sine wave voltage, 60Hz, 1min 2500 Vrms Viso (*1) No condensation Electrical isolation between input and output Please refer to de-rating characteristics. (*1) ELECTRICAL CHARACTERISTICS (unless otherwise noted, VIN=680V, Ta=25°C) Symbol Parameter VIN Input voltage Vo Test conditions Limits Unit Min. Typ. Max. Recommended range 475 680 850 V Output voltage Io=0.1 ~ 1.05A 22.8 24.0 25.2 V Reg-I Input regulation Io=1.05A, VIN=475~850V - - 100 mV Reg-L Load regulation Io=0.1 ~ 1.05A - - 150 mV Vp-p Ripple voltage Io=1.05A (*2) - - 240 mV η Efficiency Io=1.05A - 77 - % (*2) Not contain the spike noise. TEST CIRCUIT DIAGRAM Io +V IN V IN A +V O V Vo VLA312 -2425 -V IN -VO 2 Load HYBRID IC VLA312-2425 ISOLATED TYPE DC-DC CONVERTER TYPICAL CHARACTERISTICS OUTPUT VOLTAGE - OUTPUT CURRENT CHARACTERISTICS 30 OUTPUT VOLTAGE Vo (V) 120 100 80 60 40 20 0 24 21 18 15 VIN=600V 12 VIN=680V 9 6 0 -10 100 EFFICIENCY η (%) 27 3 0 10 20 30 40 50 60 70 80 0 1 1.5 2 OUTPUT CURRENT Io (A) EFFICIENCY - OUTPUT CURRENT CHARACTERISTICS EFFICIENCY - INPUT VOLTAGE CHARACTERISTICS 100 90 90 80 80 70 70 60 50 VIN=600V 40 VIN=680V 30 20 10 2.5 60 Io=1.05A 50 40 30 20 10 0 0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 400 OUTPUT CURRENT Io (A) 0.10 27 0.09 24 0.08 INPUT CURRENT IIN (A) 30 21 18 RL=22.9ohm (Io=1.05A) 15 12 9 6 600 700 800 900 INPUT CURRENT - INPUT VOLTAGE CHARACTERISTICS 0.07 0.06 0.05 0.04 0.03 RL=22.9ohm (Io=1.05A) 0.02 3 0.01 0 0.00 0 500 INPUT VOLTAGE V IN (V) OUTPUT VOLTAGE - INPUT VOLTAGE CHARACTERISTICS OUTPUT VOLTAGE Vo (V) 0.5 AMBIENT TEMPERATURE (℃) EFFICIENCY η (%) OUTPUT CURRENT DE-RATING (%) DE-RATING CHARACTERISTICS 0 100 200 300 400 500 600 700 800 900 100 200 300 400 500 600 700 800 900 INPUT VOLTAGE V IN (V) INPUT VOLTAGE V IN (V) 3 HYBRID IC VLA312-2425 ISOLATED TYPE DC-DC CONVERTER OUTLINE DIMENSION CONNECTOR 90mm Parts No. Polarity (pin1) Polarity (pin2) Polarity (pin3) CN1 B2P3-VH, JST -VIN --+VIN 55mm CN1 CN2 35mm 5mm FOR SAFETY USING Great detail and careful attention are given to the production activity of Hics, such as the development, the quality of production, and in it’s reliability. However the reliability of Hics depends not only on their own factors but also in their condition of usage. When handling Hics, please note the following cautions. CAUTIONS Packing Carrying The materials used in packing Hics can only withstand normal external conditions. When exposed to outside shocks, rain and certain environmental contaminators, the packing materials will deteriorates. Please take care in handling. 1) 2) 3) 4) 5) Don’t stack boxes too high. Avoid placing heavy materials on boxes. Boxes must be positioned correctly during transportation to avoid breakage. Don't throw or drop boxes. Keep boxes dry. Avoid rain or snow. Minimal vibration and shock during transportation is desirable. Storage When storing Hics, please observe the following notices or possible deterioration of their electrical characteristics, risk of solderability, and external damage may occur. 1) Devices must be stored where fluctuation of temperature and humidity is minimal, and must not be exposed to direct sunlight. Store at the normal temperature of 5 to 30 degrees Celsius with humidity at 40 to 60%. 2) Avoid locations where corrosive gasses are generated or where much dust accumulates. 3) Storage cases must be static proof. 4) Avoid putting weight on boxes. Extended storage When extended storage is necessary, Hics must be kept non-processed. When using Hics which have been stored for more than one year or under severe conditions, be sure to check that the exterior is free from flaw and other damages. Maximum ratings To prevent any electrical damages, use Hics within the maximum ratings. current, voltage, etc. must not exceed these conditions. Polarity To protect Hics from destruction and deterioration due to wrong insertion, make sure of polarity in inserting leads into the board holes, conforming to the external view for the terminal arrangement. 4 The temperature, CN2 B2P-VH, JST +VO -VO --- HYBRID IC VLA312-2425 ISOLATED TYPE DC-DC CONVERTER Marketing division, Marketing planning department 6-41 Tsukuba, Isahaya, Nagasaki, 854-0065 Japan Keep safety first in your circuit designs! ・ISAHAYA Electronics Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (1)placement of substitutive, auxiliary circuits, (2)use of non-flammable material or (3)prevention against any malfunction or mishap. Notes regarding these materials ・These materials are intended as a reference to our customers in the selection of the ISAHAYA products best suited to the customer's application; they don't convey any license under any intellectual property rights, or any other rights, belonging to ISAHAYA Electronics Corporation or a third party. ・ISAHAYA Electronics Corporation assumes no responsibility for any damage, or infringement of any third party's rights, originating in the use of any product data, diagrams, charts or circuit application examples contained in these materials. ・All information contained in these materials, including product data, diagrams and charts, represent information on products at the time of publication of these materials, and are subject to change by ISAHAYA Electronics Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact ISAHAYA Electronics Corporation or an authorized ISAHAYA products distributor for the latest product information before purchasing a product listed herein. ・ISAHAYA Electronics Corporation products are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact ISAHAYA Electronics Corporation or an authorized ISAHAYA products distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. ・The prior written approval of ISAHAYA Electronics Corporation is necessary to reprint or reproduce in whole or in part these materials. ・If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or re-export contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. ・Please contact ISAHAYA Electronics Corporation or an authorized ISAHAYA products distributor for further details on these materials or the products contained therein. 5 December. 2008