ISSI IS25LD512

512Kbit/1 Mbit / 2 Mbit Single Operating Voltage Serial
Flash Memory With 100 MHz Dual-Output SPI Bus
IS25LD512/010/020
FEATURES
• Single Power Supply Operation
- Low voltage range: 2.3 V – 3.6 V
• Low Power Consumption
- Typical 10 mA active read current
- Typical 15 mA program/erase current
• Memory Organization
- IS25LD512: 64K x 8 (512 Kbit)
- IS25LD010: 128K x 8 (1 Mbit)
- IS25LD020: 256K x 8 (2 Mbit)
• Hardware Write Protection
- Protect and unprotect the device from write
operation by Write Protect (WP#) Pin
• Cost Effective Sector/Block Architecture
- 512Kb : Uniform 4KByte sectors / Two uniform
32KByte blocks
- 1Mb : Uniform 4KByte sectors / Four uniform
32KByte blocks
- 2Mb : Uniform 4KByte sectors / Four uniform
64KByte blocks
• Low standby current 1uA (Typ)
• Serial Peripheral Interface (SPI) Compatible
- Supports single- or dual-output
- Supports SPI Modes 0 and 3
- Maximum 33 MHz clock rate for normal read
- Maximum 100 MHz clock rate for fast read
• Page Program (up to 256 Bytes) Operation
- Typical 2 ms per page program
• Sector, Block or Chip Erase Operation
- Maximum 10 ms sector, block or chip erase
• Software Write Protection
- The Block Protect (BP2, BP1, BP0) bits allow
partial or entire memory to be configured as readonly
• High Product Endurance
- Guaranteed 200,000 program/erase cycles per
single sector
- Minimum 20 years data retention
• Industrial Standard Pin-out and Package
- 8-pin 150mil SOIC
- 8-pin VVSOP
- 8-contact WSON
- 8-pin TSSOP
- 8-pin USON
- Lead-free (Pb-free) package
• Security function
- Build in Safe Guard function and sector unlock
function to make the flash Robust (Appendix1&2)
GENERAL DESCRIPTION
The IS25LD512/010/020 are 512Kbit/ 1Mbit / 2Mbit Serial Peripheral Interface (SPI) Flash memories, providing
single- or dual-output. The devices are designed to support a 33 MHz clock rate in normal read mode, and 100
MHz in fast read, the fastest in the industry. The devices use a single low voltage power supply, wide operating
voltage ranging from 2.3 Volt to 3.6 Volt, to perform read, erase and program operations. The devices can be
programmed in standard EPROM programmers.
The IS25LD512/010/020 are accessed through a 4-wire SPI Interface consisting of Serial Data Input/Output
(SlO), Serial Data Output (SO), Serial Clock (SCK), and Chip Enable (CE#) pins. They comply with all
recognized command codes and operations. The dual-output fast read operation provides and effective serial
data rate of 200MHz.
The devices support page program mode, where 1 to 256 bytes data can be programmed into the memory in
one program operation. These devices are divided into uniform 4 KByte sectors or uniform 32 KByte
blocks.(IS25LD020 is uniform 4 KByte sectors or uniform 64 KByte).
The IS25LD512/010/020 are manufactured on pFLASH™’s advanced non-volatile technology. The devices are
offered in 8-pin SOIC 150mil, 8-contact WSON, 8-pin VVSOP, 8-pin USON and 8-pin TSSOP. The devices
operate at wide temperatures between -40°C to +105°C.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
1
IS25LD512/010/020
CONNECTION DIAGRAMS
CE#
1
8
SO
2
7
WP#
GND
Vcc
CE#
1
8 Vcc
SO
2
7 HOLD#
HOLD#
3
6
SCK
4
5
SIO
WP# 3
6 SCK
GND 4
5 SIO
8-Contact WSON
8-Pin SOIC/VVSOP
CE#
SO
WP#
GND
1
2
3
4
8
7
6
5
Vcc
HOLD#
SCK
SIO
8-Pin TSSOP
PIN DESCRIPTIONS
SYMBOL
TYPE
DESCRIPTION
CE#
INPUT
SCK
SIO
SO
GND
Vcc
WP#
INPUT
INPUT/OUTPUT
OUTPUT
HOLD#
INPUT
Chip Enable: CE# low activates the devices internal circuitries for
device operation. CE# high deselects the devices and switches into
standby mode to reduce the power consumption. When a device is not
selected, data will not be accepted via the serial input pin (SlO), and the
serial output pin (SO) will remain in a high impedance state.
Serial Data Clock
Serial Data Input/Output
Serial Data Output
Ground
Device Power Supply
Write Protect: A hardware program/erase protection for all or part of a
memory array. When the WP# pin is low, memory array write-protection depends
on the setting of BP2, BP1 and BP0 bits in the Status Register. When the WP# is
high, the devices are not write-protected.
Hold: Pause serial communication by the master device without resetting
the serial sequence.
INPUT
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
2
IS25LD512/010/020
BLOCK DIAGRAM
SIO
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
3
IS25LD512/010/020
SPI MODES DESCRIPTION
Multiple IS25LD512/010/020 devices can be connected
on the SPI serial bus and controlled by a SPI Master,
i.e. microcontroller, as shown in Figure 1. The devices
support either of two SPI modes:
Mode 0 (0, 0)
Mode 3 (1, 1)
The difference between these two modes is the clock
polarity when the SPI master is in Stand-by mode: the
serial clock remains at “0” (SCK = 0) for Mode 0 and
the clock remains at “1” (SCK = 1) for Mode 3. Please
refer to Figure 2. For both modes, the input data is
latched on the rising edge of Serial Clock (SCK), and
the output data is available from the falling edge of
SCK.
Figure 1. Connection Diagram among SPI Master and SPI Slaves (Memory Devices)
SDIO
SPI Interface with
(0,0) or (1,1)
SDI
SCK
SCK
SPI Master
(i.e. Microcontroller)
CS3
CS2
SO
SIO
SCK
SPI Memory
Device
CS1
CE#
WP#
SO
SIO
SCK
CE#
WP#
CE#
HOLD#
SIO
SPI Memory
Device
SPI Memory
Device
HOLD#
SO
WP#
HOLD#
Note: 1. The Write Protect (WP#) and Hold (HOLD#) signals should be driven high or low as
Figure 2. SPI Modes Supported
SCK
Mode 0 (0, 0)
SCK
Mode 3 (1, 1)
SIO
MSb
Input mode
SO
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
MSb
4
IS25LD512/010/020
SYSTEM CONFIGURATION
The IS25LD512/010/020 devices are designed to interface directly with the synchronous Serial Peripheral
Interface (SPI) of the Motorola MC68HCxx series of microcontrollers or any SPI interface-equipped system
controllers. The devices have two superset features that can be enabled through specific software instructions
and the Configuration Register:
Memory Density
Block No.
Block Size
Sector Size
Sector No.
(Kbytes)
(Kbytes)
(1)
4
000000h - 000FFFh
Sector 1
4
001000h - 001FFFh
:
:
:
Sector 7
4
007000h - 007FFFh
Sector 8
4
008000h - 008FFFh
Sector 9
4
009000h - 009FFFh
:
:
000000h - 006FFFh
Sector 15
4
00F000h - 00FFFFh
Sector 0
Block 0
32
512 Kbit
1 Mbit
Block 1
Memory Density
32
Address Range
Block 2
32
"
"
010000h - 017FFFh
Block 3
32
"
"
018000h - 01FFFFh
Block No.
Block
Size
(KBytes)
Block 0
64
Block 1
64
:
Block 3
:
64
2 Mbit
Sector No.
Sector 0
Sector 1
:
Sector 15
Sector 16
Sector 17
:
Sector 31
:
:
Sector
Size
(KBytes)
4
4
:
4
4
4
:
4
:
4
Address Range
000000h - 000FFFh
001000h - 001FFFh
:
00F000h - 00FFFFh
010000h - 010FFFh
011000h - 011FFFh
:
01F000h - 01FFFFh
:
030000h – 03FFFFh
Table 1-1. Block/Sector Addresses of IS25LD512/010/020
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
5
IS25LD512/010/020
REGISTERS (CONTINUED)
STATUS REGISTER
Refer to Tables 5 and 6 for Status Register Format and are allowed. The WEL bit is set by a Write Enable
(WREN) instruction. Each write register, program and
Status Register Bit Definitions.
erase instruction must be preceded by a WREN
The BP0, BP1, BP2, and SRWD are volatile memory
instruction. The WEL bit can be reset by a Write
cells that can be written by a Write Status Register
Disable (WRDI) instruction. It will automatically be the
(WRSR) instruction. The default value of the BP2, BP1, reset after the completion of a write instruction.
BP0 were set to “0” and SRWD bits was set to “0” at
factory. Once a “0” or “1”is written, it will not be
BP2, BP1, BP0 bits: The Block Protection (BP2, BP1,
changed by device power-up or power-down, and can BP0) bits are used to define the portion of the memory
only be altered by the next WRSR instruction. The
area to be protected. Refer to Tables 7, 8 and 9 for the
Status Register can be read by the Read Status
Block Write Protection bit settings. When a defined
Register (RDSR). Refer to Table 10 for Instruction Set. combination of BP2, BP1 and BP0 bits are set, the
corresponding memory area is protected. Any program
The function of Status Register bits are described as
or erase operation to that area will be inhibited. Note:
follows:
a Chip Erase (CHIP_ER) instruction is executed
successfully only if all the Block Protection Bits are set
WIP bit: The Write In Progress (WIP) bit is read-only,
as “0”s.
and can be used to detect the progress or completion
of a program or erase operation. When the WIP bit is
SRWD bit: The Status Register Write Disable (SRWD)
“0”, the device is ready for a write status register,
bit operates in conjunction with the Write Protection
program or erase operation. When the WIP bit is “1”,
(WP#) signal to provide a Hardware Protection Mode.
the device is busy.
When the SRWD is set to “0”, the Status Register is
not write-protected. When the SRWD is set to “1” and
WEL bit: The Write Enable Latch (WEL) bit indicates
the WP# is pulled low (VIL), the volatile bits of Status
the status of the internal write enable latch. When the
Register (SRWD, BP2, BP1, BP0) become read-only,
WEL is “0”, the write enable latch is disabled, and all
and a WRSR instruction will be ignored. If the SRWD is
write operations, including write status register, page
set to “1” and WP# is pulled high (VIH), the Status
program, sector erase, block and chip erase operations Register can be changed by a WRSR instruction.
are inhibited. When the WEL bit is “1”, write operations
Table 5. Status Register Format
Default (flash bit)
Bit 7
SRWD1
0
Bit 6
Bit 5
Reserved
0
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
Bit 4
BP2
0
Bit 3
BP1
0
Bit 2
BP0
0
Bit 1
WEL
0
Bit 0
WIP
0
6
IS25LD512/010/020
REGISTERS (CONTINUED)
Table 6. Status Register Bit Definition
Bit
Name
Bit 0
WIP
Bit 1
WEL
Bit 2
Bit 3
Bit 4
Bits 5 - 6
BP0
BP1
BP2
N/A
Bit 7
SRWD
Definition
Read/Write
Non-Volatile
bit
R
No
R/W
No
R/W
Yes
Write In Progress Bit:
"0" indicates the device is ready
"1" indicates a write cycle is in progress and the device is busy
Write Enable Latch:
"0" indicates the device is not write enabled
"1" indicates the device is write enabled (default)
Block Protection Bit: (See Table 7 and Table 8 for details)
"0" indicates the specific blocks are not write-protected (default)
"1" indicates the specific blocks are write-protected
Reserved: Always "0"s
Status Register Write Disable: (See Table 9 for details)
"0" indicates the Status Register is not write-protected (default)
"1" indicates the Status Register is write-protected
N/A
R/W
Yes
Table 8. Block Write Protect Bits for IS25LD512/010/020
Status Register Bits
BP1
BP0
0
Protected Memory Area
IS25LD512A
IS25LD010A
IS25LD020
0
None
None
None
0
1
None
Upper quarter (Block 3)
01800h-01FFFFh
Upper quarter (Block 3)
03000h-03FFFFh
1
0
None
Upper half (Block 2 & 3)
010000h-01FFFFh
Upper half (Block 2 & 3)
020000h-03FFFFh
1
1
All Blocks
000000h-00FFFFh
All Blocks
000000h-01FFFFh
All Blocks
000000h-03FFFFh
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
7
IS25LD512/010/020
REGISTERS (CONTINUED)
PROTECTION MODE
The IS25LD512/010/020 have two types of writeprotection mechanisms: hardware and software.
These are used to prevent irrelevant operation in a
possibly noisy environment and protect the data
integrity.
HARDWARE WRITE-PROTECTION
The devices provide two hardware write-protection
features:
Table 9. Hardware Write Protection on Status
Register
SRWD
0
1
0
1
WP#
Low
Low
High
High
Status Register
Writable
Protected
Writable
Writable
a. When inputting a program, erase or write status
register instruction, the number of clock pulse is
checked to determine whether it is a multiple of eight
before the executing. Any incomplete instruction
command sequence will be ignored.
b. The Write Protection (WP#) pin provides a
hardware write protection method for BP2, BP1, BP0
and SRWD in the Status Register. Refer to the
STATUS REGISTER description.
c.
Write inhibit is 1.8V, all write sequence will be
ignored when Vcc drop to 1.8V and lower
SOFTWARE WRITE PROTECTION
The IS25LD512/010/020 also provides two software
write protection features:
a. Before the execution of any program, erase or write
status register instruction, the Write Enable Latch
(WEL) bit must be enabled by executing a Write
Enable (WREN) instruction. If the WEL bit is not
enabled first, the program, erase or write register
instruction will be ignored.
b. The Block Protection (BP2, BP1, BP0) bits allow part
or the whole memory area to be write-protected.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
8
IS25LD512/010/020
DEVICE OPERATION
The IS25LD512/010/020 utilize an 8-bit instruction
register. Refer to Table 10 Instruction Set for details of
the Instructions and Instruction Codes. All instructions,
addresses, and data are shifted in with the most
significant bit (MSB) first on Serial Data Input (SI). The
input data on SI is latched on the rising edge of Serial
Clock (SCK) after Chip Enable (CE#) is driven low
(VIL). Every instruction sequence starts with a one-byte
instruction code and is followed by address bytes, data
bytes, or both address bytes and data bytes,
depending on the type of instruction. CE# must be
driven high (VIH) after the last bit of the instruction
sequence has been shifted in.
The timing for each instruction is illustrated in the
following operational descriptions.
Table 10. Instruction Set
Instruction Name
Hex
Code
RDID
JEDEC ID READ
ABh
9Fh
RDMDID
WREN
WRDI
RDSR
WRSR
READ
FAST_READ
FRDO
PAGE_ PROG
90h
06h
04h
05h
01h
03h
0Bh
3Bh
02h
SECTOR_ER
D7h/
20h
D8h
C7h/
60h
BLOCK_ER
CHIP_ER
Operation
Command
Cycle
Maximum
Frequency
Read Manufacturer and Product ID
Read Manufacturer and Product ID by JEDEC ID
Command
Read Manufacturer and Device ID
Write Enable
Write Disable
Read Status Register
Write Status Register
Read Data Bytes from Memory at Normal Read Mode
Read Data Bytes from Memory at Fast Read Mode
Fast Read Dual Output
Page Program Data Bytes Into Memory
4 Bytes
1 Byte
100 MHz
100 MHz
100 MHz
100 MHz
100 MHz
100 MHz
100 MHz
33 MHz
100 MHz
100 MHz
50 MHz
Sector Erase
4 Bytes
1 Byte
1 Byte
1 Byte
2 Bytes
4 Bytes
5 Bytes
5 Bytes
4 Bytes +
256B
4 Bytes
Block Erase
Chip Erase
4 Bytes
1 Byte
100 MHz
100 MHz
100 MHz
HOLD OPERATION
HOLD# is used in conjunction with CE# to select
the IS25LD512/010/020. When the devices are
selected and a serial sequence is underway,
HOLD# can be used to pause the serial
communication with the master device without
resetting the serial sequence. To pause, HOLD# is
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
brought low while the SCK signal is low. To resume
serial communication, HOLD# is brought high while
the SCK signal is low (SCK may still toggle during
HOLD). Inputs to SlO will be ignored while SO is in
the high impedance state.
9
IS25LD512/010/020
DEVICE OPERATION (CONTINUED)
RDID COMMAND (READ PRODUCT
IDENTIFICATION) OPERATION
The Read Product Identification (RDID) instruction is
Table 11. Product Identification
for reading out the old style of 8-bit Electronic
Signature, whose values are shown as table of ID
Definitions. This is not same as RDID or JEDEC ID
Product Identification
instruction. It’s not recommended to use for new
First Byte
design. For new design, please use RDID or JEDEC ID
Manufacturer ID
Second Byte
instruction.
Device
ID:
Device
ID 1
The RDES instruction code is followed by three dummy
bytes, each bit being latched-in on SI during the rising
IS25LD512
05h
edge of SCK. Then the Device ID is shifted out on SO
IS25LD010
10h
with the MSB first, each bit been shifted out during the
IS25LD020
11h
falling edge of SCK. The RDES instruction is ended by
CE# goes high. The Device ID outputs repeatedly if
continuously send the additional clock cycles on SCK
while CE# is at low.
Data
9Dh
7Fh
Device ID 2
20h
21h
22h
Figure 3. Read Product Identification Sequence
CE#
0
1
7
8
9
38
31
46
39
47
54
SCK
INSTRUCTION
SI
SO
3 Dummy Bytes
1010 1011b
HIGH IMPEDANCE
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
Device ID1
Device ID1
Device ID1
10
IS25LD512/010/020
DEVICE OPERATION (CONTINUED)
JEDEC ID READ COMMAND (READ PRODUCT IDENTIFICATION BY JEDEC ID)
OPERATION
The JEDEC ID READ instruction allows the user to
read the manufacturer and product ID of devices. Refer
to Table 11 Product Identification for pFlash
Manufacturer ID and Device ID. After the JEDEC ID
READ command is input, the second Manufacturer ID
(7Fh) is shifted out on SO with the MSB first, followed
by the first Manufacturer ID (9Dh) and the Device ID
(22h, in the case of the IS25LD020), each bit shifted
out during the falling edge of SCK. If CE# stays low
after the last bit of the Device ID is shifted out, the
Manufacturer ID and Device ID will loop until CE# is
pulled high.
Figure 4. Read Product Identification by JEDEC ID READ Sequence
CE#
0
15 16
7 8
23 24
31
SCK
INSTRUCTION
SI
SO
1001 1111b
HIGH IMPEDANCE
Manufacture ID2
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
Manufacture ID1
Device ID2
11
IS25LD512/010/020
DEVICE OPERATION (CONTINUED)
RDMDID COMMAND (READ DEVICE MANUFACTURER AND DEVICE ID)
OPERATION
The RDMDID instruction allows the user to read the
manufacturer and product ID of devices. Refer to Table
11 Product Identification for pFlash Manufacturer ID
and Device ID. The RDMDID command is input,
followed by a 24-bit address pointing to an ID table.
The table contains the first Manufacturer ID (9Dh) and
the Device ID (22h, in the case of the IS25LD020), and
is shifted out on SO with the MSB first, each bit shifted
out during the falling edge of SCK. If CE# stays low
after the last bit of the Device ID is shifted out, the
Manufacturer ID and Device ID will loop until CE# is
pulled high.
Figure 5. Read Product Identification by RDMDID READ Sequence
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
12
IS25LD512/010/020
Note :
(1) ADDRESS A0 = 0, will output the 1st manufacture ID (9Dh) first -> device ID1 -> 2nd manufacture ID (7Fh)
ADDRESS A0 = 1, will output the device ID1 -> 1st manufacture ID (9D) -> 2nd manufacture ID (7Fh)
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
13
IS25LD512/010/020
DEVICE OPERATION (CONTINUED)
WRITE ENABLE OPERATION
The Write Enable (WREN) instruction is used to set the
Write Enable Latch (WEL) bit. The WEL bit of the
IS25LD512/010/020 is reset to the write –protected
state after power-up. The WEL bit must be write
enabled before any write operation, including sector,
block erase, chip erase, page program and write status
register operations. The WEL bit will be reset to the
write-protect state automatically upon completion of a
write operation. The WREN instruction is required
before any above operation is executed.
Figure 6. Write Enable Sequence
SIO
WRDI COMMAND (WRITE DISABLE) OPERATION
The Write Disable (WRDI) instruction resets the WEL
bit and disables all write instructions. The WRDI
instruction is not required after the execution of a write
instruction, since the WEL bit is automatically reset.
Figure 7. Write Disable Sequence
SIO
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
14
IS25LD512/010/020
DEVICE OPERATION (CONTINUED)
RDSR COMMAND (READ STATUS REGISTER) OPERATION
The Read Status Register (RDSR) instruction provides
access to the Status Register. During the execution of
a program, erase or write status register operation, all
other instructions will be ignored except the RDSR
instruction, which can be used to check the progress or
completion of an operation by reading the WIP bit of
Status Register.
Figure 8. Read Status Register Sequence
SIO
WRSR COMMAND (WRITE STATUS REGISTER) OPERATION
The Write Status Register (WRSR) instruction allows
the user to enable or disable the block protection and
status register write protection features by writing “0”s
or “1” s into the volatile BP2, BP1, BP0 and SRWD
bits.
Figure 9. Write Status Register Sequence
SIO
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
15
IS25LD512/010/020
DEVICE OPERATION (CONTINUED)
READ COMMAND (READ DATA) OPERATION
The Read Data (READ) instruction is used to read
memory data of a IS25LD512/010/020 under normal
mode running up to 33 MHz.
The READ instruction code is transmitted via the SlO
line, followed by three address bytes (A23 - A0) of the
first memory location to be read. A total of 24 address
bits are shifted in, but only AMS (most significant
address) - A0 are decoded. The remaining bits (A23 –
AMS) are ignored. The first byte addressed can be at
any memory location. Upon completion, any data on
the Sl will be ignored. Refer to Table 12 for the related
Address Key.
The first byte data (D7 - D0) addressed is then shifted
out on the SO line, MSb first. A single byte of data, or
up to the whole memory array, can be read out in one
READ instruction. The address is automatically
incremented after each byte of data is shifted out. The
read operation can be terminated at any time by driving
CE# high (VIH) after the data comes out. When the
highest address of the devices is reached, the address
counter will roll over to the 000000h address, allowing
the entire memory to be read in one continuous READ
instruction.
Table 12. Address Key
Address
AN (AMS – A0)
Don't Care Bits
IS25LD020
A17 - A0
A23 – A18
IS25LD010
A16 - A0
A23 – A17
IS25LD512
A15 - A0
A23 – A16
Figure 12. Read Data Sequence
SIO
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
16
IS25LD512/010/020
DEVICE OPERATION (CONTINUED)
FAST_READ COMMAND (FAST READ DATA) OPERATION
The FAST_READ instruction is used to read memory
data at up to a 100 MHz clock.
The first byte addressed can be at any memory
location. The address is automatically incremented
The FAST_READ instruction code is followed by three after each byte of data is shifted out. When the highest
address bytes (A23 - A0) and a dummy byte (8 clocks), address is reached, the address counter will roll over to
transmitted via the SI line, with each bit latched-in
the 000000h address, allowing the entire memory to be
during the rising edge of SCK. Then the first data byte read with a single FAST_READ instruction. The
addressed is shifted out on the SO line, with each bit
FAST_READ instruction is terminated by driving CE#
shifted out at a maximum frequency fCT, during the
high (VIH).
falling edge of SCK.
Figure 13. Fast Read Data Sequence
SIO
SIO
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
17
IS25LD512/010/020
DEVICE OPERATION (CONTINUED)
FRDO COMMAND (FAST READ DUAL OUTPUT) OPERATION
The FRDO instruction is used to read memory data on
two output pins each at up to a 100 MHz clock.
is output on SO, while simultaneously the second bit is
output on SIO.
The FRDO instruction code is followed by three
address bytes (A23 - A0) and a dummy byte (8 clocks),
transmitted via the SI line, with each bit latched-in
during the rising edge of SCK. Then the first data byte
addressed is shifted out on the SO and SIO lines, with
each pair of bits shifted out at a maximum frequency
fCT, during the falling edge of SCK. The first bit (MSb)
The first byte addressed can be at any memory
location. The address is automatically incremented
after each byte of data is shifted out. When the highest
address is reached, the address counter will roll over to
the 000000h address, allowing the entire memory to be
read with a single FRDO instruction. FRDO instruction
is terminated by driving CE# high (VIH).
Figure 14. Fast Read Dual-Output Sequence
CE#
0
1
2
3
4
5
6
7
8
9
10
11
28
30
31
2
1
0
29
...
SCK
3 - BYTE ADDRESS
SIO
INSTRUCTION = 0011 1011b
23
22 21
... 3
HIGH IMPEDANCE
SO
CE#
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
6
4
2
0
6
4
2
0
6
1
7
SCK
SIO
DATA OUT 1
SO
HIGH IMPEDANCE
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
7
5
3
DATA OUT 2
1
7
5
3
18
IS25LD512/010/020
DEVICE OPERATION (CONTINUED)
PAGE_PROG COMMAND (PAGE PROGRAM) OPERATION
The Page Program (PAGE_PROG) instruction allows
up to 256 bytes data to be programmed into memory in
a single operation. The destination of the memory to be
programmed must be outside the protected memory
area set by the Block Protection (BP2, BP1, BP0) bits.
A PAGE_PROG instruction which attempts to program
into a page that is write-protected will be ignored.
Before the execution of PAGE_PROG instruction, the
Write Enable Latch (WEL) must be enabled through a
Write Enable (WREN) instruction.
The PAGE_PROG instruction code, three address
bytes and program data (1 to 256 bytes) are input via
the SlO line. Program operation will start immediately
after the CE# is brought high, otherwise the
PAGE_PROG instruction will not be executed. The
internal control logic automatically handles the
programming voltages and timing. During a program
operation, all instructions will be ignored except the
RDSR instruction. The progress or completion of the
program operation can be determined by reading the
WIP bit in Status Register via a RDSR instruction. If
the WIP bit is “1”, the program operation is still in
progress. If WIP bit is “0”, the program operation has
completed.
If more than 256 bytes data are sent to a device, the
address counter rolls over within the same page, the
previously latched data are discarded, and the last 256
bytes data are kept to be programmed into the page.
The starting byte can be anywhere within the page.
When the end of the page is reached, the address will
wrap around to the beginning of the same page. If the
data to be programmed are less than a full page, the
data of all other bytes on the same page will remain
unchanged.
Note: A program operation can alter “1”s into “0”s, but
an erase operation is required to change “0”s back to
“1”s. A byte cannot be reprogrammed without first
erasing the whole sector or block.
Figure 15. Page Program Sequence
SIO
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
19
IS25LD512/010/020
DEVICE OPERATION (CONTINUED)
ERASE OPERATION
The memory array of the IS25LD512/010 is organized
into uniform 4 KByte sectors or 32 KByte uniform
blocks (a block consists of eight adjacent sectors).
IS25LD020 is organized into uniform 4 KByte sectors
or 64 KByte uniform blocks (a block consists of sixteen
adjacent sectors)
Before a byte can be reprogrammed, the sector or
block that contains the byte must be erased (erasing
sets bits to “1”). In order to erase the devices, there are
three erase instructions available: Sector Erase
(SECTOR_ER), Block Erase (BLOCK_ER) and Chip
Erase (CHIP_ER). A sector erase operation allows any
individual sector to be erased without affecting the data
in other sectors. A block erase operation erases any
individual block. A chip erase operation erases the
whole memory array of a device. A sector erase, block
erase or chip erase operation can be executed prior to
any programming operation.
SECTOR_ER COMMAND (SECTOR ERASE)
OPERATION
A SECTOR_ER instruction erases a 4 KByte sector
Before the execution of a SECTOR_ER instruction, the
Write Enable Latch (WEL) must be set via a Write
Enable (WREN) instruction. The WEL bit is reset
automatically after the completion of sector an erase
operation.
instruction. The progress or completion of the erase
operation can be determined by reading the WIP bit in
the Status Register using a RDSR instruction. If the
WIP bit is “1”, the erase operation is still in progress. If
the WIP bit is “0”, the erase operation has been
completed.
BLOCK_ER COMMAND (BLOCK ERASE)
OPERATION
A Block Erase (BLOCK_ER) instruction erases a 64
KByte block of the IS25LD020, and 32 KByte block of
the IS25LD512C/010C. Before the execution of a
BLOCK_ER instruction, the Write Enable Latch (WEL)
must be set via a Write Enable (WREN) instruction.
The WEL is reset automatically after the completion of
a block erase operation.
The BLOCK_ER instruction code and three address
bytes are input via SI. Erase operation will start
immediately after the CE# is pulled high, otherwise the
BLOCK_ER instruction will not be executed. The
internal control logic automatically handles the erase
voltage and timing. Refer to Figure 15 for Block Erase
Sequence.
CHIP_ER COMMAND (CHIP ERASE) OPERATION
A Chip Erase (CHIP_ER) instruction erases the entire
memory array of a IS25LD512/010/020. Before the
execution of CHIP_ER instruction, the Write Enable
Latch (WEL) must be set via a Write Enable (WREN)
A SECTOR_ER instruction is entered, after CE# is
instruction. The WEL is reset automatically after
pulled low to select the device and stays low during the completion of a chip erase operation.
entire instruction sequence The SECTOR_ER
instruction code, and three address bytes are input via The CHIP_ER instruction code is input via the SI.
SI. Erase operation will start immediately after CE# is
Erase operation will start immediately after CE# is
pulled high. The internal control logic automatically
pulled high, otherwise the CHIP_ER instruction will not
handles the erase voltage and timing. Refer to Figure
be executed. The internal control logic automatically
14 for Sector Erase Sequence.
handles the erase voltage and timing. Refer to Figure
16 for Chip Erase Sequence.
During an erase operation, all instruction will be
ignored except the Read Status Register (RDSR)
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
20
IS25LD512/010/020
DEVICE OPERATION (CONTINUED)
Figure 16. Sector Erase Sequence
SIO
Figure 17. Block Erase Sequence
SIO
Figure 18. Chip Erase Sequence
SIO
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
21
IS25LD512/010/020
ABSOLUTE MAXIMUM RATINGS (1)
-65oC to +125oC
-65oC to +125oC
240oC 3 Seconds
260oC 3 Seconds
-0.5 V to VCC + 0.5 V
-0.5 V to VCC + 0.5 V
-0.5 V to +6.0 V
Temperature Under Bias
Storage Temperature
Standard Package
Lead-free Package
Input Voltage with Respect to Ground on All Pins (2)
All Output Voltage with Respect to Ground
VCC (2)
Notes:
1. Applied conditions greater than those listed in “Absolute Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only. The functional operation of the device conditions that exceed those
indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating
condition for extended periods may affect device reliability.
Surface Mount Lead Soldering Temperature
2. Maximum DC voltage on input or I/O pins is VCC + 0.5 V. During voltage transitions, input or I/O pins may
overshoot VCC by + 2.0 V for a period of time not to exceed 20 ns. Minimum DC voltage on input or I/O pins is
-0.5 V. During voltage transitions, input or I/O pins may undershoot GND by -2.0 V for a period of time not to
exceed 20 ns.
DC AND AC OPERATING RANGE
Part Number
Operating Temperature (Extended Grade)
Operating Temperature (Industrial Grade)
Operating Temperature (Automotive, A1 Grade)
Operating Temperature (Automotive, A2 Grade)
Operating Temperature (Automotive, A3 Grade)
Vcc Power Supply
IS25LD512/010/020
-40oC to 105oC
-40oC to 85oC
-40oC to 85oC
-40oC to 105oC
-40oC to 125oC
2.3 V – 3.6 V
DC CHARACTERISTICS
Applicable over recommended operating range from:
VCC = 2.3 V to 3.6 V (unless otherwise noted).
Symbol
Parameter
Condition
Min
Typ
Max
Units
VCC = 3.6V at 33 MHz, SO = Open
10
15
mA
15
30
mA
ICC1
Vcc Active Read Current
ICC2
Vcc Program/Erase Current
VCC = 3.6V at 33 MHz, SO = Open
ISB1
Vcc Standby Current CMOS
VCC = 3.6V, CE# = VCC
10
A
ISB2
Vcc Standby Current TTL
VCC = 3.6V, CE# = VIH to VCC
3
mA
ILI
Input Leakage Current
VIN = 0V to VCC
1
A
o
o
ILO
Output Leakage Current
1
A
VIL
Input Low Voltage
-0.5
0.8
V
VIH
Input HIgh Voltage
0.7VCC
VCC + 0.3
V
VOL
Output Low Voltage
0.45
V
VOH
Output High Voltage
VIN = 0V to VCC, TAC = 0 C to 85 C
2.3V < VCC < 3.6V
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
IOL = 2.1 mA
IOH = -100 A
VCC - 0.2
V
22
IS25LD512/010/020
AC CHARACTERISTICS
Applicable over recommended operating range from, VCC = 2.3 V to 3.6 V
CL = 1 TTL Gate and 10 pF (unless otherwise noted).
Symbol
fCT
fC
tRI
tFI
tCKH
tCKL
tCEH
tCS
tCH
tDS
tDH
tHS
tHD
tV
tOH
tLZ
tHZ
tDIS
tEC
tPP
tVCS
tw
Parameter
Clock Frequency for fast read mode
Clock Frequency for read mode
Input Rise Time
Input Fall Time
SCK High Time
SCK Low Time
CE# High Time
CE# Setup Time
CE# Hold Time
Data In Setup Time
Data in Hold Time
Hold Setup Time
Hold Time
Output Valid
Output Hold Time Normal Mode
Hold to Output Low Z
Hold to Output High Z
Output Disable Time
Secter/Block/Chip Erase Time
Page Program Time
VCC Set-up Time
Write Status Register time (flash bit)
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
Min
0
0
Typ
Max
100
33
8
8
200
200
100
10
5
Units
MHz
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
ms
10
s
ms
4
4
25
10
5
2
2
15
15
8
0
2
50
23
IS25LD512/010/020
AC CHARACTERISTICS (CONTINUED)
SERIAL INPUT/OUTPUT TIMING (1)
SIO
Note: 1. For SPI Mode 0 (0,0)
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
24
IS25LD512/010/020
AC CHARACTERISTICS (CONTINUED)
HOLD TIMING
PIN CAPACITANCE (f = 1 MHz, T = 25°C )
CIN
COUT
Typ
4
8
Max
6
12
Units
pF
pF
Conditions
VIN = 0 V
VOUT = 0 V
Note: These parameters are characterized but not 100% tested.
OUTPUT TEST LOAD
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
INPUT TEST WAVEFORMS
AND MEASUREMENT LEVEL
25
IS25LD512/010/020
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
26
IS25LD512/010/020
POWER-UP AND POWER-DOWN
At Power-up and Power-down, the device must not be
selected (CE# must follow the voltage applied on Vcc)
until Vcc reaches the correct value:
- Vcc(min) at Power-up, and then for a further delay of
tVCE
- Vss at Power-down
Usually a simple pull-up resistor on CE# can be used
to insure safe and proper Power-up and Power-down.
To avoid data corruption and inadvertent write
operations during power up, a Power On Reset (POR)
circuit is included. The logic inside the device is held
reset while Vcc is less than the POR threshold value
(Vwi) during power up, the device does not respond to
any instruction until a time delay of tPUW has elapsed
after the moment that Vcc rised above the VWI
threshold. However, the correct operation of the device
is not guaranteed if, by this time, Vcc is still below
Vcc(min). No Write Status Register, Program or Erase
instructions should be sent until the later of:
- tPUW after Vcc passed the VWI threshold
- tVCE after Vcc passed the Vcc(min) level
At Power-up, the device is in the following state:
- The device is in the Standby mode
- The Write Enable Latch (WEL) bit is reset
At Power-down, when Vcc drops from the operating
voltage, to below the Vwi, all write operations are
disabled
and the device does not respond to any write
instruction.
Vcc
Vcc(max)
All Write Commands are Rejected
Chip Selection Not Allowed
Vcc(min)
Reset State
tVCE
V (write inhibit)
Read Access Allowed
Device fully accessible
tPUW
Time
Symbol
Parameter
tVCE
*1
Vcc(min) to CE# Low
tPUW
*1
Power-Up time delay to Write instruction
*1
VWI
Write Inhibit Voltage
Note : *1. These parameters are characterized only.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
Min.
Max.
10
Unit
us
1
10
ms
1.6
1.8
2.1
V
27
IS25LD512/010/020
PROGRAM/ERASE PERFORMANCE
Parameter
Sector Erase Time
Block Erase Time
Chip Erase Time
Page Programming Time
Unit
ms
ms
ms
ms
Typ
2
Max
10
10
10
5
Remarks
From writing erase command to erase completion
From writing erase command to erase completion
From writing erase command to erase completion
From writing program command to program completion
Note: These parameters are characterized and are not 100% tested.
RELIABILITY CHARACTERISTICS
Parameter
Endurance
Data Retention
ESD – Human Body Model
ESD – Machine Model
Latch-Up
Min
200,000
20
2,000
200
100 + ICC1
Typ
Unit
Cycles
Years
Volts
Volts
mA
Test Method
JEDEC Standard A117
JEDEC Standard A103
JEDEC Standard A114
JEDEC Standard A115
JEDEC Standard 78
Note: These parameters are characterized and are not 100% tested.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
28
IS25LD512/010/020
PACKAGE TYPE INFORMATION
`
JN
8-Pin JEDEC 150mil Broad Small Outline Integrated Circuit (SOIC) Package
(measure in millimeters)
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
29
IS25LD512/010/020
JD
8-pin TSSOP Package (measure in millimeters)
Pin1
6.2
6.6
4.3
4.5
0.127
Detail A
2.9
3.1
1.00
1.05
1.05
1.20
Detail A
0.25
0.30
GAGE PLANE
0.05
0.15
0.25
0.65
0.5
0.7
00
80
Unit : millimeters
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
30
IS25LD512/010/020
PACKAGE TYPE INFORMATION (CONTINUED)
JP
8-Contact Ulta-Thin Small Outline No-Lead (WSON) Package (measure in millimeters)
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
31
IS25LD512/010/020
PACKAGE TYPE INFORMATION (CONTINUED)
JA
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
32
IS25LD512/010/020
PACKAGE TYPE INFORMATION (CONTINUED)
JV
8-pin VVSOP Package 150mil
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
33
IS25LD512/010/020
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
34
IS25LD512/010/020
PACKAGE TYPE INFORMATION (CONTINUED)
JU
8-pin USON Package (measure in millimeters)
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
35
IS25LD512/010/020
Appendix1: Safe Guard function
Safe Guard function is a security function for customer to protect by sector (4Kbyte).
Every sector has one bit register to decide it will under safe guard protect or not. (“0”means protect and “1”
means not protect by safe guard.) IS25LD512 (sector 0~sector 15), IS25LD010 (sector 0~sector 31) and
IS25LD020 (sector 0~sector 63)
*safe guard function priority is higher than status register (BP0/1/2)
Mapping table for safe guard register
Sector0
Sector1
Sector2
Sector3
Sector4
Sector5
Sector6
Sector7
Sector8
Sector9
Sector10
Sector11
Sector12
Sector13
Sector14
Sector15
Address[9:0]
000h
000h
000h
000h
000h
000h
000h
000h
001h
001h
001h
001h
001h
001h
001h
001h
D7
D6
1
1
1
1
1
1
1
0
1
1
1
1
1
1
1
0
D5
1
1
1
1
1
1
0
1
1
1
1
1
1
1
0
1
D4
1
1
1
1
1
0
1
1
1
1
1
1
1
0
1
1
D3
1
1
1
1
0
1
1
1
1
1
1
1
0
1
1
1
D2
1
1
1
0
1
1
1
1
1
1
1
0
1
1
1
1
D0
1
0
1
1
1
1
1
1
1
0
1
1
1
1
1
1
1
1
0
1
1
1
1
1
0
0
1
1
1
1
1
1
1
0
1
1
1
1
1
1
1
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Sector56
007h
1
1
1
1
1
Sector57
007h
1
1
1
1
1
Sector58
007h
1
1
1
1
1
Sector59
007h
1
1
1
1
0
Sector60
007h
1
1
1
0
1
Sector61
007h
1
1
0
1
1
Sector62
007h
1
0
1
1
1
Sector63
007h
0
1
1
1
1
Chip Erase disable* 008h
0
0
0
0
0
Note:1. Please set the Chip Erase disable to "0" after finished the register setting.
2. Please set the address 009h to "00" after finished the register setting.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
D1
1
1
0
1
1
1
1
1
1
1
0
1
1
1
1
1
1
0
1
1
1
1
1
1
0
0
1
1
1
1
1
1
1
0
36
IS25LD512/010/020
Read Safe Guard register
The READ Safe Guard instruction code is transmitted via the SlO line, followed by three address bytes (A23 - A0) of
the first register location to be read. The first byte data (D7 - D0) addressed is then shifted out on the SO line, MSb
first. The address is automatically incremented after each byte of data is shifted out. The read operation can be
terminated at any time by driving CE# high (VIH) after the data comes out.
CS
1
2
7 8 9 10
23 24 25 26
31 32 33 34
39 40 41 42
47 48
SCK
SI
2Fh
A23-A0
SO
1st byte
2nd byte
D7-D0
D7-D0
Fig a. Timing waveform of Read Safe guard register
Erase Safe Guard register
If we want to erase the safe guard register to let the flash into unprotect status, it needs five continuous
instructions. If any instruction is wrong, the erase command will be ignored. Erase wait time follow product erase
timing spec.
Fig b. shows the complete steps for Erase safe guard register.
Program Safe Guard register
If we want to erase the safe guard register to let the flash into unprotect status, it needs five continuous
instructions. If any instruction is wrong, the program command will be ignored. The Program safe guard
instruction allows up to 256 bytes data to be programmed into memory in a single operation. Program wait time
follow product program timing spec.
Fig c. shows the complete steps for program safe guard register.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
37
IS25LD512/010/020
Fig b. Erase safe guard register
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
38
IS25LD512/010/020
1st byte
2nd byte
Fig c. program safe guard register
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
39
IS25LD512/010/020
Appendix2: Sector Unlock function
Instruction Name
SECT_UNLOCK
SECT_LOCK
Hex
Code
26h
24h
Operation
Sector unlock
Sector lock
Command
Cycle
4 Bytes
1 Byte
Maximum
Frequency
100 MHz
100 MHz
SEC_UNLOCK COMMAND OPERATION
The Sector unlock command allows the user to
select a specific sector to allow program and erase
operations. This instruction is effective when the
blocks are designated as write-protected through
the BP0, BP1 and BP2 bits in the status register.
Only one sector can be enabled at any time. To
enable a different sector, a previously enabled
sector must be disabled by executing a Sector Lock
command. The instruction code is followed by a
24-bit address specifying the target sector, but A0
through A11 are not decoded. The remaining
sectors within the same block remain in read-only
mode.
Figure d. Sector Unlock Sequence
Note: 1.If the clock number will not match 8 clocks(command)+ 24 clocks (address), it will be ignored.
2.It must be executed write enable (06h) before sector unlock instructions.
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
40
IS25LD512/010/020
SECT_LOCK COMMAND OPERATION
The Sector Lock command reverses the function of
the Sector Unlock command. The instruction code
does not require an address to be specified, as only
one sector can be enabled at a time. The remaining
sectors within the same block remain in read-only
mode.
Figure e. Sector Lock Sequence
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
41
IS25LD512/010/020
PRODUCT ORDERING INFORMATION
IS25LD*** - JN L E
Temperature Range
E = Extended Grade (-40°C to +105°C)
I = Industrial Grade (-40°C to +85°C)
A1 = Automotive, A1 Grade (-40°C to +85°C)
A2 = Automotive, A2 Grade (-40°C to +105°C)
A3 = Automotive, A3 Grade (-40°C to +125°C)
Environmental Attribute
L = Lead-free (Pb-free) package
Package Type
JN = 8-pin SOIC 150mil
JP = 8-pin WSON
JD = 8-pin TSSOP
JV = 8-pin VVSOP 150mil
JU = 8-pin USON
Device Number
IS25LD512/010/020
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
42
IS25LD512/010/020
ORDERING INFORMATION:
Density
Frequency
(MHz)
512K
100
1Mb
100
2Mb
100
Order Part Number
Package
IS25LD512-JNLE
IS25LD512-JPLE
IS25LD512-JDLE
IS25LD512-JVLE
IS25LD512-JULE
IS25LD512-JNLI
IS25LD512-JPLI
IS25LD512-JDLI
IS25LD512-JVLI
IS25LD512-JULI
IS25LD512-JNLA1
IS25LD512-JPLA1
IS25LD512-JDLA1
IS25LD512-JVLA1
IS25LD512-JULA1
IS25LD512-JNLA2
IS25LD512-JPLA2
IS25LD512-JDLA2
IS25LD512-JVLA2
IS25LD512-JULA2
IS25LD010-JNLE
IS25LD010-JPLE
IS25LD010-JDLE
IS25LD010-JVLE
IS25LD010-JNLI
IS25LD010-JPLI
IS25LD010-JDLI
IS25LD010-JVLI
IS25LD010-JNLA1
IS25LD010-JPLA1
IS25LD010-JDLA1
IS25LD010-JVLA1
IS25LD010-JNLA2
IS25LD010-JPLA2
IS25LD010-JDLA2
IS25LD010-JVLA2
IS25LD020-JNLE
IS25LD020-JPLE
IS25LD020-JDLE
IS25LD020-JVLE
IS25LD020-JNLI
IS25LD020-JPLI
IS25LD020-JDLI
IS25LD020-JVLI
IS25LD020-JNLA1
IS25LD020-JPLA1
IS25LD020-JDLA1
IS25LD020-JVLA1
IS25LD020-JNLA2
IS25LD020-JPLA2
IS25LD020-JDLA2
IS25LD020-JVLA2
8-pin SOIC 150mil
8-pin WSON
8-pin TSSOP
8-pin VVSOP 150mil
8-pin USON
8-pin SOIC 150mil
8-pin WSON
8-pin TSSOP
8-pin VVSOP 150mil
8-pin USON
8-pin SOIC 150mil
8-pin WSON
8-pin TSSOP
8-pin VVSOP 150mil
8-pin USON
8-pin SOIC 150mil
8-pin WSON
8-pin TSSOP
8-pin VVSOP 150mil
8-pin USON
8-pin SOIC 150mil
8-pin WSON
8-pin TSSOP
8-pin VVSOP 150mil
8-pin SOIC 150mil
8-pin WSON
8-pin TSSOP
8-pin VVSOP 150mil
8-pin SOIC 150mil
8-pin WSON
8-pin TSSOP
8-pin VVSOP 150mil
8-pin SOIC 150mil
8-pin WSON
8-pin TSSOP
8-pin VVSOP 150mil
8S 150mil SOIC
8K WSON (Back Side Metal)
8-pin TSSOP
8-pin VVSOP 150mil
8S 150mil SOIC
8K WSON (Back Side Metal)
8-pin TSSOP
8-pin VVSOP 150mil
8S 150mil SOIC
8K WSON (Back Side Metal)
8-pin TSSOP
8-pin VVSOP 150mil
8S 150mil SOIC
8K WSON (Back Side Metal)
8-pin TSSOP
8-pin VVSOP 150mil
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
08/09/2012
43