IS25LP128 128M-BIT 3V SERIAL FLASH MEMORY WITH 133MHZ MULTI I/O SPI & QUAD I/O QPI DTR INTERFACE PRELIMINARY DATA SHEET IS25LP128 128M-BIT 3V SERIAL FLASH MEMORY WITH 133MHZ MULTI I/O SPI & QUAD I/O QPI DTR INTERFACE PRELIMINARY INFORMATION FEATURES Industry Standard Serial Interface - IS25LP128:128M-bit/16M-byte - 256 bytes per Programmable Page - Supports standard SPI, Fast, Dual, Dual I/O, QPI, SPI DTR, Dual SPI DTR I/O, and QPI DTR - Supports Serial Flash Discoverable Parameters (SFDP) High Performance Serial Flash (SPI) - 50MHz Normal and 133Mhz Fast Read - 532 MHz equivalent QPI - DTR (Dual Transfer Rate) up to 66MHz - Selectable dummy cycles - Configurable drive strength - Supports SPI Modes 0 and 3 - More than 100,000 erase/program cycles - More than 20-year data retention Flexible & Efficient Memory Architecture - Chip Erase:128Mbit with Uniform: Sector/Block Erase (4K/32K/64K-Byte) - Program 1 to 256 bytes per page - Program/Erase Suspend & Resume Low Power with Wide Temp. Ranges - Single 2.3V to 3.6V Voltage Supply - 10 mA Active Read Current - 5 µA Standby Current - Deep Power Down - Temp Grades: Extended: -40°C to +105°C Auto Grade: up to +125°C (call factory) Advanced Security Protection - Software and Hardware Write Protection - Power Supply lock protect - 4x256-Byte dedicated security area with user-lockable bits, (OTP) One Time Programmable Memory - 128 bit Unique ID for each device Industry Standard Pin-out & Packages - JM =16-pin SOIC 300mil - JB = 8-pin SOIC 208mil - JF = 8-pin VSOP 208mil - JK = 8-contact WSON 6x5mm - JL = 8-contact WSON 8x6mm - KGD (call factory) Efficient Read and Program modes - Low Instruction Overhead Operations - Continuous Read 8/16/32/64-Byte burst - Selectable burst length - QPI for reduced instruction overhead - Allows XIP operations (execute in place) Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 2 IS25LP128 GENERAL DESCRIPTION The IS25LP128 Serial Flash memory offers a storage solution with the flexibility and performance in a simplified pin count package. ISSI’s “Industry Standard Serial Interface” Flash are for systems that have limited space, pins, and power. The IS25LP128 are accessed through a 4-wire SPI Interface consisting of a Serial Data Input (Sl), Serial Data Output (SO), Serial Clock (SCK), and Chip Enable (CE#) pins, which also serve as multi-I/O (see pin descriptions). The device supports the standard Serial Peripheral Interface (SPI), Dual/Quad output (SPI), and Dual/Quad I/O (SPI). Clock frequencies of up to 133MHz allow for equivalent clock rates of up to 532MHz (133MHz x 4) allowing more than 66Mbytes/s of throughput. The IS25xP series of Flash adds support for DTR (Double Transfer Rate) commands that transfer addresses and read data on both edges of the clock. These transfer rates can outperform 16-bit Parallel Flash memories allowing for efficient memory access for a XIP (execute in place) operation. The memory array is organized into programmable pages of 256-bytes each. The IS25LP128 supports page program mode where 1 to 256 bytes of data can be programmed into the memory with one command. QPI (Quad Peripheral Interface) supports 2-cycle instruction further reducing instruction times. Pages can be erased in groups of 4K-byte sectors, 32K-byte blocks, 64K-byte blocks, and/or the entire chip. The uniform sectors and blocks allow greater flexibility for a variety of applications requiring solid data retention. GLOSSARY Standard SPI The IS25LP128 is accessed through a 4-wire SPI Interface consisting of Serial Data Input (Sl), Serial Data Output (SO), Serial Clock (SCK), and Chip Enable (CE#) pins. Instructions are inputted through the SI pin to encode instructions, addresses, or input data to the device on the rising edge of SCK. The DO pin is used to read data or check the status of the device on the falling edge of SCK. This device supports SPI bus operation mode (0,0) and (1,1). Mutil I/O SPI The IS25LP128 allows accessing enhanced SPI protocol to use Dual output, Dual input and output, and Quad input and output operation. Executing these instructions through SPI mode will achieve double or quadruple the transfer bandwidth for READ and PROGRAM. Quad I/O QPI The IS25LP128 can enable QPI protocol by issuing an “Enter QPI mode (35h)” command. The QPI mode uses four IO pins for input and output to reduce SPI instruction overhead and increase output bandwidth. QPI mode can exit by issuing an “Exit QPI (F5h) command. A power reset or software reset can also return the device into the standard SPI mode. SI and SO pins become bidirectional IO0 and IO1, and WP# and HOLD# pins become IO2 and IO3 respectively during QPI mode. DTR In addition to SPI and QPI features, IS25LP128 also supports SPI DTR READ. SPI DTR allows high data throughput while running at lower clock frequencies. As SPI DTR READ option uses both rising and falling clock to drive output, the dummy cycles are reduced by half as well. Programmable drive strength and Selectable burst setting. The IS25LP128 offers programmable output drive strength and selectable burst (wrap) length features to increase the efficiency and performance of READ operations. The driver strength and burst setting features are controlled by setting READ registers. A total of six different drive strengths and four different burst sizes (8/16/32/64 Bytes) are selectable. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 3 IS25LP128 TABLE OF CONTENTS 1. PIN CONFIGURATION ................................................................................................................................. 6 2. PIN DESCRIPTIONS .................................................................................................................................... 7 3. BLOCK DIAGRAM ........................................................................................................................................ 8 4. SPI MODES DESCRIPTION ........................................................................................................................ 9 5. SYSTEM CONFIGURATION ...................................................................................................................... 11 5.1 BLOCK/SECTOR ADDRESSES .......................................................................................................... 11 6. REGISTERS ............................................................................................................................................... 12 6.1. STATUS REGISTER ........................................................................................................................... 12 6.2. FUNCTION REGISTER ....................................................................................................................... 14 6.3 READ REGISTERS .............................................................................................................................. 15 7. PROTECTION MODE................................................................................................................................. 17 7.1 HARDWARE WRITE PROTECTION.................................................................................................... 17 7.2 SOFTWARE WRITE PROTECTION .................................................................................................... 17 8. DEVICE OPERATION ................................................................................................................................ 18 8.1 NORMAL READ OPERATION (NORD, 03h) ....................................................................................... 20 8.2 FAST READ DATA OPERATION (FRD, 0Bh) ..................................................................................... 21 8.3 HOLD OPERATION .............................................................................................................................. 23 8.4 FAST READ DUAL I/O OPERATION (FRDIO, BBh) ........................................................................... 23 8.5 FAST READ DUAL OUTPUT OPERATION (FRDO, 3Bh) ................................................................... 25 8.6 FAST READ QUAD I/O OPERATION (FRQIO, EBh) .......................................................................... 26 8.7 PAGE PROGRAM OPERATION (PP, 02h) .......................................................................................... 29 8.8 QUAD INPUT PAGE PROGRAM OPERATION (PPQ, 32h/38h) ........................................................ 31 8.9 ERASE OPERATION ........................................................................................................................... 32 8.10 SECTOR ERASE OPERATION (SER, D7h/20h) ............................................................................... 33 8.11 BLOCK ERASE OPERATION (BER32K:52h, BER64K:D8h) ............................................................ 34 8.12 CHIP ERASE OPERATION (CER, C7h/60h) ..................................................................................... 36 8.13 WRITE ENABLE OPERATION (WREN, 06h) .................................................................................... 37 8.14 WRITE DISABLE OPERATION (WRDI, 04h) ..................................................................................... 38 8.15 READ STATUS REGISTER OPERATION (RDSR, 05h) ................................................................... 39 8.16 WRITE STATUS REGISTER OPERATION (WRSR, 01h) ................................................................. 40 8.17 READ FUNCTION REGISTER OPERATION (RDFR, 48h) ............................................................... 41 8.18 WRITE FUNCTION REGISTER OPERATION (WRFR, 42h)............................................................. 42 8.19 ENTER QUAD PERIPHERAL INTERFACE (QPI) MODE OPERATION (QIOEN,35h; QIODI,F5h) . 43 8.20 PROGRAM/ERASE SUSPEND & RESUME ...................................................................................... 44 8.21 DEEP POWER DOWN (DP, B9h) ...................................................................................................... 45 8.22 RELEASE DEEP POWER DOWN (RDPD, ABh) ............................................................................... 46 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 4 IS25LP128 8.23 SET READ PARAMETERS OPERATION (SRP, C0h) ...................................................................... 47 8.24 READ PRODUCT IDENTIFICATION (RDID, ABh) ............................................................................ 49 8.25 READ PRODUCT IDENTIFICATION BY JEDEC ID OPERATION (RDJDID, 9Fh) ........................... 50 8.26 READ DEVICE MANUFACTURER AND DEVICE ID OPERATION (RDMDID, 90h) ........................ 51 8.27 READ UNIQUE ID NUMBER (RDUID, 4Bh) ...................................................................................... 52 8.28 READ SFDP OPERATION (RDSFDP, 5Ah) ...................................................................................... 53 8.29 NO OPERATION (NOP, 00h) ............................................................................................................. 54 8.30 SOFTWARE RESET (RESET-ENABLE (RSTEN, 66h) AND RESET (RST, 99h) ............................ 54 8.31 MODE RESET OPERATION (RSTM, FFh) ........................................................................................ 55 8.32 SECURITY INFORMATION ROW...................................................................................................... 55 8.33 INFORMATION ROW ERASE OPERATION (IRER, 64h) ................................................................. 56 8.34 INFORMATION ROW PROGRAM OPERATION (IRP, 62h) ............................................................. 57 8.35 INFORMATION ROW READ OPERATION (IRRD, 68h) ................................................................... 58 8.36 FAST READ DTR MODE OPERATION (FRDTR, 0Dh) ..................................................................... 59 8.37 FAST READ DUAL IO DTR MODE OPERATION (FRDDTR, BDh) .................................................. 60 8.38 FAST READ QUAD IO DTR MODE OPERATION (FRQDTR, EDh) ................................................. 61 8.39 SECTOR LOCK/UNLOCK FUNCTIONS ............................................................................................ 62 9. ELECTRICAL CHARACTERISTICS........................................................................................................... 64 9.1 ABSOLUTE MAXIMUM RATINGS (1) ................................................................................................... 64 9.2 OPERATING RANGE ........................................................................................................................... 64 9.3 DC CHARACTERISTICS ...................................................................................................................... 64 9.4 AC MEASUREMENT CONDITIONS .................................................................................................... 65 9.5 AC CHARACTERISTICS ...................................................................................................................... 66 9.6 SERIAL INPUT/OUTPUT TIMING ........................................................................................................ 67 9.7 POWER-UP AND POWER-DOWN ...................................................................................................... 69 9.8 PROGRAM/ERASE PERFORMANCE ................................................................................................. 69 10. PACKAGE TYPE INFORMATION ......................................................................................................... 71 10.1 8-Pin JEDEC 208mil Broad Small Outline Integrated Circuit (SOIC) Package (JB) (1) ..................... 71 10.2 8-Contact Ultra-Thin Small Outline No-Lead (WSON) Package 6x5mm (JK) (1) .............................. 72 10.3 8-Contact Ultra-Thin Small Outline No-Lead (WSON) Package 8x6mm (JL) (1)............................... 73 10.4 8-Pin 208mil VSOP Package (JF) (1) ................................................................................................ 74 10.5 16-lead Plastic Small Outline package (300 mils body width) (JM) (1) .............................................. 75 11. ORDERING INFORMATION ................................................................................................................. 76 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 5 IS25LP128 1. PIN CONFIGURATION CE# 1 Vcc 8 8 Vcc CE# 1 SO (IO1) 2 7 HOLD# (IO3) WP# (IO2) 3 6 SCK GND 4 5 SI (IO0) SO (IO1) 2 7 HOLD# (IO3) WP# (IO2) 3 6 GND 4 5 SI (IO0) 8-pin WSON 6x5mm 8-pin WSON 8x6mm 8-pin SOIC 208mil 8-pin VSOP 208mil HOLD# (IO3) 1 16 SCK Vcc 2 15 SI (IO0) NC 3 14 NC NC 4 13 NC NC 5 12 NC NC 6 11 NC CE# 7 10 GND SO (IO1) 8 9 WP# (IO2) 16-Pin SOIC 300mil Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 6 SCK IS25LP128 2. PIN DESCRIPTIONS SYMBOL TYPE DESCRIPTION Chip Enable: The Chip Enable (CE#) pin enables and disables the devices operation. When CE# is high the device is deselected and output pins are in a high impedance state. When deselected the devices non-critical internal circuitry power down to allow minimal levels of power consumption while in a standby state. CE# INPUT When CE# is pulled low the device will be selected and brought out of standby mode. The device is considered active and instructions can be written to, data read, and written to the device. After power-up, CE# must transition from high to low before a new instruction will be accepted. Keeping CE# in a high state deselects the device and switches it into its low power state. Data will not be accepted when CE# is high. Serial Data Input, Serial Output, and IOs (SI, SO, IO0, and IO1): SI (IO0), SO (IO1) INPUT/OUTPUT This device supports standard SPI, Dual SPI, and Quad SPI operation. Standard SPI instructions use the unidirectional SI (Serial Input) pin to write instructions, addresses, or data to the device on the rising edge of the Serial Clock (SCK). Standard SPI also uses the unidirectional SO (Serial Output) to read data or status from the device on the falling edge of the serial clock (SCK). In Dual and Quad SPI mode, SI and SO become bidirectional IO pins to write instructions, addresses or data to the device on the rising edge of the Serial Clock (SCK) and read data or status from the device on the falling edge of SCK. Quad SPI instructions use the WP# and HOLD# pins as IO2 and IO3 respectively. WP# (IO2) INPUT/OUTPUT Write Protect/Serial Data IO (IO2): The WP# pin protects the Status Register from being written. When the WP# is low the status registers are write-protected and viceversa for high. When the QE bit is set to “1”, the WP# pin (Write Protect) function is not available since this pin is used for IO2. Hold/Serial Data IO (IO3): Pauses serial communication by the master device without resetting the serial sequence. When the QE bit of Status Register is set to “1”, HOLD# pin is not available since it becomes IO3. HOLD# (IO3) INPUT/OUTPUT The HOLD# pin allows the device to be paused while it is selected. The HOLD# pin is active low. When HOLD# is in a low state, and CE# is low, the SO pin will be at high impedance. Device operation can resume when HOLD# pin is brought to a high state. When the QE bit of Status Register is set for Quad I/O, the HOLD# pin function is not available and becomes IO3 for Multi-I/O SPI mode. SCK INPUT Vcc POWER GND GROUND NC Unused Serial Data Clock: Synchronized Clock for input and output timing operations. Power: Device Core Power Supply Ground: Connect to ground when referenced to Vcc NC: Pins labeled “NC” stand for “No Connect” and should be left uncommitted. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 7 IS25LP128 3. BLOCK DIAGRAM Control Logic High Voltage Generator Status Register I/O Buf f ers and Data Latches 256 Bytes Page Buf f er SCK WP# (IO2) SI (IO0) SO (IO1) Y- Decoder X- Decoder HOLD# (IO3) Serial Peripheral Interface CE# Memory Array Address Latch & Counter Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 8 IS25LP128 4. SPI MODES DESCRIPTION Multiple IS25LP128 devices can be connected on the SPI serial bus and controlled by a SPI Master, i.e. microcontroller, as shown in Figure 4.1. The devices support either of two SPI modes: Mode 0 (0, 0) Mode 3 (1, 1) The difference between these two modes is the clock polarity. When the SPI master is in stand-by mode, the serial clock remains at “0” (SCK = 0) for Mode 0 and the clock remains at “1” (SCK = 1) for Mode 3. Please refer to Figure 4.2 and Figure 4.3 for SPI and QPI mode. In both modes, the input data is latched on the rising edge of Serial Clock (SCK), and the output data is available from the falling edge of SCK. Figure 4.1 Connection Diagram among SPI Master and SPI Slaves (Memory Devices) SDO SPI Interf ace with (0,0) or (1,1) SDI SCK SCK SPI Master (i.e. Microcontroller) CS CS S0 SI SPI Memory Device CS CE# WP# SCK S0 SI SPI Memory Device HOLD# CE# WP# SCK S0 SI SPI Memory Device HOLD# CE# WP# HOLD# Note: SI and SO pins become bidirectional IO0 and IO1, and WP# and HOLD# pins become IO2 and IO3 respectively during QPI mode. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 9 IS25LP128 Figure 4.2 SPI Mode Support SCK Mode 0 (0,0) SCK Mode 3 (1,1) MSB SI SO MSB Figure 4.3 QPI Mode Support CE# 0 1 2 3 4 IO0 C4 C0 20 16 12 8 4 0 4 0 4 IO1 C5 C1 21 17 13 9 5 1 5 1 IO2 C6 C2 22 18 14 10 6 2 6 IO3 C7 C3 23 19 15 11 7 3 7 Mode 3 5 6 7 8 9 13 14 0 4 0 5 1 5 1 2 6 2 6 2 3 7 3 7 3 10 11 12 SCK Mode 0 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 10 15 IS25LP128 5. SYSTEM CONFIGURATION The IS25LP128 is designed to interface directly with the synchronous Serial Peripheral Interface (SPI) of the Motorola MC68HCxx series of microcontrollers or any SPI interface-equipped system controllers. The memory array of IS25LP128 is divided into uniform 4 Kbyte sectors or uniform 32K/64 Kbyte blocks (a block consists of eight/sixteen adjacent sectors respectively). Table 5.1 illustrates the memory map of the device. The Status Register controls how the memory is mapped. 5.1 BLOCK/SECTOR ADDRESSES Table 5.1 Block/Sector Addresses of IS25LP128 Memory Density Block No. (64Kbyte) Block No. (32Kbyte) Block 0 Block 0 Block 1 Block 2 Block 1 Block 3 Block 4 Block 2 Block 5 128Mbit : : Block 506 Block 253 Block 507 Block 508 Block 253 Block 509 Block 510 Block 255 Block 511 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 Sector 0 : : Sector Size (Kbytes) 4 : : 000000h - 000FFFh : : Sector 15 4 00F000h - 00FFFFh Sector 16 : 4 : 010000h - 010FFFh : Sector No. Address Range : : : Sector 31 Sector 32 : : 4 4 : : 01F000h - 01FFFFh 020000h - 020FFFh : : Sector 47 : 4 : 02F000h – 02FFFFh : Sector 4048 : : 4 : : FD0000h – FD0FFFh : : Sector 4063 4 FDF000h – FDFFFFh Sector 4064 4 FE0000h – FE0FFFh : : : : : : Sector 4079 Sector 4080 : 4 4 : FEF000h – FEFFFFh FF0000h – FF0FFFh : : : : Sector 4095 4 FFF000h – FFFFFFh 11 IS25LP128 6. REGISTERS The IS25LP128 has three sets of Registers: Status, Function and Read. 6.1. STATUS REGISTER Status Register Format and Status Register Bit Definitions are described in Tables 6.1 & 6.2. Table 6.1 Status Register Format Default (Flash bit) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SRWD QE BP3 BP2 BP1 BP0 WEL WIP 0 0 0 0 0 0 0 0 Table 6.2 Status Register Bit Definition Bit Name Bit 0 WIP Bit 1 WEL Bit 2 Bit 3 Bit 4 Bit 5 BP0 BP1 BP2 BP3 Bit 6 QE Bit 7 SRWD Definition Write In Progress Bit: "0" indicates the device is ready(default) "1" indicates a write cycle is in progress and the device is busy Write Enable Latch: "0" indicates the device is not write enabled (default) "1" indicates the device is write enabled Block Protection Bit: (See Tables 6.3 for details) "0" indicates the specific blocks are not write-protected (default) "1" indicates the specific blocks are write-protected Quad Enable bit: “0” indicates the Quad output function disable (default) “1” indicates the Quad output function enable Status Register Write Disable: (See Table 7.1 for details) "0" indicates the Status Register is not write-protected (default) "1" indicates the Status Register is write-protected Read/Write Non-Volatile bit R No R/W No R/W Yes R/W Yes R/W Yes The BP0, BP1, BP2, BP3, SRWD, and QE are non-volatile memory cells that can be written by a Write Status Register (WRSR) instruction. The default value of the BP2, BP1, BP0, and SRWD bits were set to “0” at factory. The Status Register can be read by the Read Status Register (RDSR). The function of Status Register bits are described as follows: WIP bit: The Write In Progress (WIP) bit is read-only, and can be used to detect the progress or completion of a program or erase operation. When the WIP bit is “0”, the device is ready for write status register, program or erase operation. When the WIP bit is “1”, the device is busy. WEL bit: The Write Enable Latch (WEL) bit indicates the status of the internal write enable latch. When the WEL is “0”, the write enable latch is disabled and all write operations, including write status register, write configuration register, page program, sector erase, block and chip erase operations are inhibited. When the WEL bit is “1”, write operations are allowed. The WEL bit is set by a Write Enable (WREN) instruction. Each write register, program and erase instruction must be preceded by a WREN instruction. The WEL bit can be reset by a Write Disable (WRDI) instruction. It will automatically be reset after the completion of any write operation. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 12 IS25LP128 BP3, BP2, BP1, BP0 bits: The Block Protection (BP3, BP2, BP1 and BP0) bits are used to define the portion of the memory area to be protected. Refer to Tables 6.3 for the Block Write Protection (BP) bit settings. When a defined combination of BP3, BP2, BP1 and BP0 bits are set, the corresponding memory area is protected. Any program or erase operation to that area will be inhibited. Note: A Chip Erase (CER) instruction will be ignored unless all the Block Protection Bits are “0”s. SRWD bit: The Status Register Write Disable (SRWD) bit operates in conjunction with the Write Protection (WP#) signal to provide a Hardware Protection Mode. When the SRWD is set to “0”, the Status Register is not write-protected. When the SRWD is set to “1” and the WP# is pulled low (VIL), the bits of Status Register (SRWD, BP3, BP2, BP1, BP0) become read-only, and a WRSR instruction will be ignored. If the SRWD is set to “1” and WP# is pulled high (VIH), the Status Register can be changed by a WRSR instruction. QE bit: The Quad Enable (QE) is a non-volatile bit in the status register that allows quad operation. When the QE bit is set to “0”, the pin WP# and HOLD# are enabled. When the QE bit is set to “1”, the IO2 and IO3 pins are enabled. Table 6.3 Block (64Kbyte) assignment by Block Write Protect (BP) Bits. Status Register Bits Protected Memory Area TBS(T/B selection) = 0, TOP area TBS(T/B selection) = 1, Bottom area 0 0( None) 0( None) 0 1 1(1 block : 255th) 1(1 block : 0th) 0 1 0 2(2 block : 254th and 255th) 2(2 block : 0th and 1st) 0 0 1 1 3(4 blocks : 252nd to 255th) 3(4 blocks : 0th to 3rd) 0 1 0 0 4(8 blocks : 248th to 255th) 4(8 blocks : 0th to 7th) 0 1 0 1 5(16 blocks :232nd to 255th) 5(16 blocks : 0th to 15th) 0 1 1 0 6(32 blocks : 223rd to 255th) 6(32 blocks : 0th to 31st) 0 1 1 1 7(64 blocks : 191st to 255th) 7(64 blocks : 0th to 63rd) 1 0 0 0 8(128 blocks : 127th to 255th) 8(128 blocks : 0th to 127th) 1 0 0 1 9(256 blocks : 0th to 255th) All blocks 9(256 blocks : 0th to 255th) All blocks 1 0 1 0 10(256 blocks : 0th to 255th) All blocks 10(256 blocks : 0th to 255th) All blocks 1 0 1 1 11(256 blocks : 0th to 255th) All blocks 11(256 blocks : 0th to 255th) All blocks 1 1 0 0 12(256 blocks : 0th to 255th) All blocks 12(256 blocks : 0th to 255th) All blocks 1 1 0 1 13(256 blocks : 0th to 255th) All blocks 13(256 blocks : 0th to 255th) All blocks 1 1 1 0 14(256 blocks : 0th to 255th) All blocks 14(256 blocks : 0th to 255th) All blocks 1 1 1 1 15(256 blocks : 0th to 255th) All blocks 15(256 blocks : 0th to 255th) All blocks BP3 BP2 BP1 BP0 0 0 0 0 0 0 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 13 IS25LP128 6.2. FUNCTION REGISTER Function Register Format and Bit definition are described in Table 6.4 and 6.5 Table 6.4 Function Register Format Default Bit 7 Bit 6 Bit 5 IRL3 IRL2 IRL1 0 0 0 Bit 4 IRL0 (Reserved) 0 Bit 3 Bit 2 Bit 1 Bit 0 ESUS PSUS TBS Reserved 0 0 0 0 Table 6.5 Function Register Bit Definition Bit Name Definition Bit 0 Reserved Bit 1 Top/Bottom Selection Bit 2 PSUS Bit 3 ESUS Bit 4 IR Lock 0 Bit 5 IR Lock 1 Bit 6 IR Lock 2 Bit 7 IR Lock 3 Reserved Top/Bottom Selection. (See Tables 6.3 for details) “0” indicates Top area. “1” indicates Bottom area. Program suspend bit: “0” indicates program is not suspend “1” indicates program is suspend Erase suspend bit: "0" indicates Erase is not suspend "1" indicates Erase is suspend Lock the information row 0: “0” indicates the information row can be programmed “1” indicates the information row cannot be programmed Lock the information row 1: “0” indicates the information row can be programmed “1” indicates the information row cannot be programmed Lock the information row 2: “0” indicates the information row can be programmed “1” indicates the information row cannot be programmed Lock the information row 3: “0” indicates the information row can be programmed “1” indicates the information row cannot be programmed Read/Write Reserved Non-Volatile bit Reserved R/W Yes R No R No R/W Yes R/W Yes R/W Yes R/W Yes Note: Table 6.5 Function Register bits are only one time programmable and cannot be modified Top/Bottom Selection: BP0~3 area assignment changed from Top or Bottom. See Tables 6.5 for details The Program Suspend Status bit indicates when a Program operation has been suspended. The PSUS changes to ‘1’ after a suspend command is issued during the program operation. Once the suspended Program resumes, the PSUS bit is reset to ‘0.’ ESUS bit: The Erase Suspend Status indicates when an Erase operation has been suspended. The ESUS bit is ‘1’ after a suspend command is issued during an Erase operation. Once the suspended Erase resumes, the ESUS bit is reset to ‘0.’ IR lock bit 0 ~ 3: The information row lock bits are programmable. If the bit set to “1”, it can’t be programmed. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 14 IS25LP128 6.3 READ REGISTERS Read Register format and Bit definitions pertaining to QPI mode are described below.’ READ PARAMETER BITS Table 6.6 defines all bits that control features in SPI/QPI modes. The ODS2, ODS1, ODS0 (P7, P6, P5) bits provide a method to set and control driver strength. The Dummy Cycle bits (P4, P3) define how many dummy cycles are used during various READ modes. The wrap selection bits (P2, P1, P0) define burst length with wrap around. The SET READ PARAMETERS Operation (SRP, C0h) is used to set all the Read Register bits, and can thereby define the output driver strength, number of dummy cycles used during READ modes, burst length with wrap around. Table 6.6 Read Parameter Table Default (Flash bit) P7 P6 P5 ODS2 ODS1 ODS0 1 1 1 P4 Dummy Cycles 0 P3 Dummy Cycles 0 P2 Wrap Enable 0 P1 Burst Length 0 Table 6.7 Burst Length Data P1 P0 8 bytes 0 0 16 bytes 0 1 32 bytes 1 0 64 bytes 1 1 Table 6.8 Wrap Function Wrap around boundary P2 Whole cell regardless of P1 and P0 value 0 Burst Length set by P1 and P0 1 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 15 P0 Burst Length 0 IS25LP128 Table 6.9 Read Dummy Cycles. Read Modes P4,P3 = 00 P4,P3 = 01 P4,P3 = 10 P4,P3 = 11 Max Freq Mode Normal Read 03h 0 0 0 0 50MHz SPI Fast read 0Bh 8 8 8 8 133MHz SPI Fast read 0Bh 6 4 8 10 133MHz QPI Dual IO Read 1 BBh 4 4 8 4 4cc : 104MHz 8cc : 133MHz SPI Fast Read Dual Output 3Bh 8 8 8 8 133MHz SPI Quad IO Read 2 EBh 6 4 8 10 4cc : 84MHz 6cc : 104MHz 8cc/10cc : 133MHz SPI , QPI Notes: 1. When 4 dummy cycles are used the max clock frequency is 104MHz; when 8 dummy cycles are used the max clock frequency is 133MHz. 2. When 4 dummy cycles are used the max clock frequency is 84MHz; when 6 dummy cycles are used the max clock frequency is 104MHz; when 8 or 10 dummy cycles are used the max clock frequency is 133MHz. 3. In SPI DTR mode the dummy cycles are reduced by half. Table 6.10 Driver Strength Table ODS2 ODS1 ODS0 Description 0 0 0 Reserved 0 0 1 12.50% 0 1 0 25% 0 1 1 37.50% 1 0 0 Reserved 1 0 1 75% 1 1 0 100% 1 1 1 50% Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 Remark Default 16 IS25LP128 7. PROTECTION MODE The IS25LP128 supports hardware and software write-protection mechanisms. 7.1 HARDWARE WRITE PROTECTION The Write Protection (WP#) pin provides a hardware write protection method for BP3, BP2, BP1, BP0, SRWD, and QE in the Status Register. Refer to the section 6.1 STATUS REGISTER. Write inhibit voltage is 2.1V. All write sequence will be ignored when Vcc drops to 2.1V or lower. 7.2 SOFTWARE WRITE PROTECTION The IS25LP128 also provides a software write protection feature. The Block Protection (BP3, BP2, BP1, BP0) bits allow part or the whole memory area to be write-protected. Table 7.1 Hardware Write Protection on Status Register SRWD WP# Status Register 0 Low Writable 1 Low Protected 0 High Writable 1 High Writable Note: Before the execution of any program, erase or write status register instruction, the Write Enable Latch (WEL) bit must be enabled by executing a Write Enable (WREN) instruction. If the WEL bit is not enabled, the program, erase or write register instruction will be ignored. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 17 IS25LP128 8. DEVICE OPERATION The IS25LP128 utilizes an 8-bit instruction register. Refer to Table 8.1. Instruction Set for details on instructions and instruction codes. All instructions, addresses, and data are shifted in with the most significant bit (MSB) first on Serial Data Input (SI) or Serial Data IOs (IO0, IO1, IO2, IO3). The input data on SI or IOs is latched on the rising edge of Serial Clock (SCK) for normal mode and both of rising and falling edges for DTR mode after Chip Enable (CE#) is driven low (VIL). Every instruction sequence starts with a one-byte instruction code and is followed by address bytes, data bytes, or both address bytes and data bytes, depending on the type of instruction. CE# must be driven high (VIH) after the last bit of the instruction sequence has been shifted in to end the operation. Table 8.1 Instruction Set Instruction Name Operation Total Bytes Mode Byte0 Byte1 Byte2 Byte3 Byte4 NORD Normal Read Mode 4 SPI 03h A <23:16> A <15:8> A <7:0> Data out FRD Fast Read Mode 5 SPI QPI 0Bh A <23:16> A <15:8> A <7:0> Dummy Byte Data out FRDIO Fast Read Dual I/O 3 SPI BBh A <23:16> Dual A <15:8> Dual A <7:0> Dual Axh Dual Dual Data out FRDO Fast Read Dual Output 5 SPI 3Bh A <23:16> A <15:8> A <7:0> Dummy Byte Dual Data out FRQIO Fast Read Quad I/O 2 SPI QPI EBh A <23:16> Quad A <15:8> Quad A <7:0> Quad Axh Quad Quad Data out FRDTR Fast Read DTR Mode 5 SPI QPI 0Dh A <23:16> A <15:8> A <7:0> Dummy Byte Dual Data out FRDDTR Fast Read Dual I/O DTR 3 SPI BDh A <23:16> Dual A <15:8> Dual A <7:0> Dual Axh Dual Dual Data out FRQDTR Fast Read Quad I/O DTR 5 SPI QPI EDh A <23:16> A <15:8> A <7:0> Dummy Byte Quad Data out PP Input Page Program 4 + 256 SPI QPI 02h 02h A <23:16> A <15:8> A <7:0> PD +256byte PPQ Quad Input Page Program 4 + 256 SPI 32h 38h A <23:16> A <15:8> A <7:0> PD +256byte Quad SER Sector Erase 4 SPI QPI D7h 20h A <23:16> A <15:8> A <7:0> BER32 (32Kb) Block Erase 32K 4 SPI QPI 52h A <23:16> A <15:8> A <7:0> BER64 (64Kb) Block Erase 64K 4 SPI QPI D8h A <23:16> A <15:8> A <7:0> CER Chip Erase 1 SPI QPI C7h 60h WREN Write Enable 1 SPI QPI 06h WRDI Write Disable 1 SPI QPI 04h RDSR WRSR RDFR WRFR Read Status Register Write Status Register Read Function Register Write Function Register 2 2 2 2 SPI QPI SPI QPI SPI QPI SPI QPI Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 05h 01h 48h 42h Byte5 Byte6 SR WSR Data Data out WFR Data 18 Comments IS25LP128 Instruction Name Operation Total Bytes Mode Byte0 QIOEN Enter QPI mode 1 SPI 35h 1 QPI F5h 1 SPI QPI 75h B0h 1 SPI QPI 7Ah 30h 1 SPI QPI B9h 4 SPI QPI 4 SPI QPI QIODI PERSUS PERRSM Power Down RDID, RDPD SRP Exit QPI mod Suspend during program/erase Resume program/erase Power Down Read ID / Release Power Down Set Read Parameters RDJDID Read JEDEC ID Command RDMDID Read Manufacturer & Device ID 4 RDIDQ Read ID QPI mode RDUID 1 Byte1 Byte2 Byte3 Byte4 ABh Dummy Byte Dummy Byte Dummy Byte ID7-ID0 (17h) C0h Data in 9Fh MID (9Dh) ID15-8 (60h) ID7-ID0 (18h) 00h MID (9Dh) ID7-ID0 (17h) 01h DID (17h) MID1 (9Dh) SPI QPI 90h 4 QPI AFh MID (9Dh) ID15-8 (60h) ID7-ID0 (18h) Read Unique ID 4 SPI QPI 4Bh XXh XXh 0Xh Data Out RDSFDP SFDP Read 5 SPI QPI 5Ah A <23:16> A <15:8> A <7:0> Dummy Byte RSTEN Software Reset Enable 1 SPI QPI 66h RST Software Reset 1 SPI QPI 99h RSTM Mode Reset 1 SPI QPI FFh IRER Erase Information Row 4 SPI QPI 64h A <23:16> A <15:8> A <7:0> IRP Program Information Row 4 + 256 SPI QPI 62h A <23:16> A <15:8> A <7:0> PD +256byte IRRD Read Information Row 4 SPI QPI 68h A <23:16> A <15:8> A <7:0> Data out Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 XXh Byte5 XXh Byte6 Data out 19 Comments IS25LP128 8.1 NORMAL READ OPERATION (NORD, 03h) The Normal Read Data (NORD) instruction is used to read memory contents of the IS25LP128 at a maximum frequency of 50MHz. The NORD instruction code is transmitted via the Sl line, followed by three address bytes (A23 - A0) of the first memory location to be read. A total of 24 address bits are shifted in. The first byte address can be at any memory location. Upon completion, any data on the Sl will be ignored. Refer to Table 8.2 for the related Address Key. The first byte data (D7 - D0) is shifted out on the SO line, MSB first. A single byte of data, or up to the whole memory array, can be read out in one READ instruction. The address is automatically incremented by one after each byte of data is shifted out. The read operation can be terminated at any time by driving CE# high (VIH) after the data comes out. When the highest address of the device is reached, the address counter will roll over to the 000000h address, allowing the entire memory to be read in one continuous READ instruction. If a Read Data instruction is issued while an Erase, Program or Write operation is in process (WIP=1) the instruction is ignored and will not have any effects on the current operation. Table 8.2 Address Key Address IS25LP128 AN (AMSB – A0) A23 - A0 Figure 8.1 Read Data Sequence CE# Mode 3 SCK Mode 0 SI SO Instruction = 03h 24 Cycles (24 ADD input) CE# Mode 3 SCK Mode 0 SI SO Data Out Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 20 IS25LP128 8.2 FAST READ DATA OPERATION (FRD, 0Bh) The FAST READ (FRD) instruction is used to read memory data at up to a 133MHz clock. The FAST READ instruction code is followed by three address bytes (A23 - A0) and a dummy byte (8 clocks), transmitted via the SI line, with each bit latched-in during the rising edge of SCK. Then the first data byte from the address is shifted out on the SO line, with each bit shifted out at a maximum frequency fCT, during the falling edge of SCK. The first byte addressed can be at any memory location. The address is automatically incremented after each byte of data is shifted out. When the highest address is reached, the address counter will roll over to the 000000h address, allowing the entire memory to be read with a single FAST READ instruction. The FAST READ instruction is terminated by driving CE# high (VIH). If a Fast Read Data instruction is issued while an Erase, Program or Write cycle is in process (WIP=1) the instruction is ignored and will not have any effects on the current cycle. Figure 8.2 Fast Read Data Sequence CE # 0 1 2 3 4 5 6 7 8 9 10 11 28 29 30 31 SCK 3-byte Address SI Instruction = 0Bh 23 22 21 ... 3 2 1 0 40 41 42 43 44 45 46 47 ... 2 1 0 ... High Impedance SO CE # 32 33 34 35 36 37 38 39 SCK SI Dummy Byte Data Out SO High Impedance Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 7 6 5 4 3 21 IS25LP128 FAST READ DATA QPI OPERATION (FRD QPI, 0Bh) The QPI FAST READ (FRD QPI) instruction is used to read memory data at up to a 133MHz clock. The FAST READ instruction code (2 clocks) is followed by three address bytes (A23-A0—6clocks) and mode bits, dummy byte (4clocks), transmitted via the QPI line, with each bit latched-in during the rising edge of SCK. Then the first data byte addressed is shifted out on the SO line, with each bit shifted out at a maximum frequency fCT, during the falling edge of SCK. . The first byte addressed can be at any memory location. The address is automatically incremented after each byte of data is shifted out. When the highest address is reached, the address counter will roll over to the 000000h address, allowing the entire memory to be read with a single FAST_READ instruction. The FAST_READ instruction is terminated by driving CE# high (VIH). If a Fast Read Data instruction is issued while an Erase, Program or Write cycle is in process (WIP=1) the instruction is ignored and will not have any effects on the current cycle Figure 8.3 Fast Read Data Sequence, QPI Mode CE# 0 1 2 3 4 5 6 7 A5 A4 A3 A2 A1 A0 8 9 10 11 12 13 14 15 16 17 SCK IO[3:0] 0Bh Address 7:4 6 Dummy Cycles 3:0 7:4 3:0 Data 1 Data 2 Note: Number of dummy cycles depends on Read Parameter setting. Detailed information in Table 6.9 Read Dummy Cycles. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 22 IS25LP128 8.3 HOLD OPERATION HOLD# is used in conjunction with CE# to select the IS25LP128. When the device is selected and a serial sequence is underway, HOLD# can be used to pause the serial communication with the master device without resetting the serial sequence. To pause, HOLD# is brought low while the SCK signal is low. To resume serial communication, HOLD# is brought high while the SCK signal is low (SCK may still toggle during HOLD). Inputs to SlO will be ignored while SO is in the high impedance state. Note: HOLD is not supported in DTR mode or with QE=1. Timing graph can be referenced in AC Parameters Figure 9.3 8.4 FAST READ DUAL I/O OPERATION (FRDIO, BBh) The FRDIO allows the address bits to be input two bits at a time. This may allow for code to be executed directly from the SPI in some applications. The FRDIO instruction code is followed by three address bytes (A23 – A0) and a mode byte, transmitted via the IO0 and IO1 lines, with each pair of bits latched-in during the rising edge of SCK. The address MSB is input on IO1, the next bit on IO0, and continues to shift in alternating on the two lines. The mode bit contains the value Ax, where x is a “don’t care” value. Then the first data byte addressed is shifted out on the IO1 and IO0 lines, with each pair of bits shifted out at a maximum frequency fCT, during the falling edge of SCK. The MSB is output on IO1, while simultaneously the second bit is output on IO0. Figure 8.4 illustrates the timing sequence. The first byte addressed can be at any memory location. The address is automatically incremented after each byte of data is shifted out. When the highest address is reached, the address counter will roll over to the 000000h address, allowing the entire memory to be read with a single FRDIO instruction. FRDIO instruction is terminated by driving CE# high (VIH). The device expects the next operation will be another FRDIO. It remains in this mode until it receives a Mode Reset (FFh) command. In subsequent FRDIO execution, the command code is skipped. It saves timing cycles as described in Figure 8.5. If a FRDIO instruction is issued while an Erase, Program or Write cycle is in process (WIP=1) the instruction is ignored and will not have any effects on the current cycle. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 23 IS25LP128 Figure 8.4 Fast Read Dual I/O Sequence (with command decode cycles) CE# 0 2 1 3 4 5 6 9 8 7 10 11 SCK 18 19 20 21 ... 3-byte Address IO0 Instruction = BBh IO1 Mode Bits 22 21 19 ... 2 0 6 4 23 22 20 ... 3 1 7 5 CE# 22 23 24 25 26 27 28 29 30 31 SCK IO switch from input to output IO0 6 4 2 0 6 Data Out 1 IO1 7 5 3 4 2 0 6 1 7 Data Out 2 7 1 5 3 Note: Number of dummy cycles depends on Read Parameter setting. Detailed information in Table 6.9 Read Dummy Cycles. Figure 8.5 Fast Read Dual I/O Sequence (without command decode cycles) CE# 0 1 2 11 3 12 13 14 15 16 17 18 19 20 21 22 23 2 0 24 … SCK IO switch from input to output 3-byte Address IO0 22 21 19 ... 2 Mode Bits 0 6 6 4 23 22 20 ... 3 1 7 5 2 0 6 Data Out 1 2 dummy cycles IO1 4 7 5 3 4 Data Out 2 1 7 5 3 1 Note: If the mode bits=Ax (x don’t care), it can execute the continuous read mode (without command). Number of dummy cycles depends on Read Parameter setting. Detailed information in Table 6.9 Read Dummy Cycles. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 24 IS25LP128 8.5 FAST READ DUAL OUTPUT OPERATION (FRDO, 3Bh) The FRDO instruction is used to read memory data on two output pins each at up to a 133MHz clock. The FRDO instruction code is followed by three address bytes (A23 – A0) and a dummy byte (8 clocks), transmitted via the SI line, with each bit latched-in during the rising edge of SCK. Then the first data byte addressed is shifted out on the SO and SIO lines, with each pair of bits shifted out at a maximum frequency fCT, during the falling edge of SCK. The first bit (MSB) is output on SO, while simultaneously the second bit is output on SIO. The first byte addressed can be at any memory location. The address is automatically incremented after each byte of data is shifted out. When the highest address is reached, the address counter will roll over to the 000000h address, allowing the entire memory to be read with a single FRDO instruction. FRDO instruction is terminated by driving CE# high (VIH). If a FRDO instruction is issued while an Erase, Program or Write cycle is in process (BUSY=1) the instruction is ignored and will not have any effects on the current cycle. Figure 8.6 Fast Read Dual-Output Sequence CE# 0 1 2 3 5 4 6 7 8 9 10 11 28 29 30 31 SCK 3-byte Address SI Instruction = 3Bh 23 22 21 ... 3 2 1 0 40 41 42 43 44 45 46 47 ... 6 4 2 0 6 4 2 0 ... 1 ... High Impedance SO CE# 32 33 34 35 36 37 38 39 SCK SI High Impedance SO High Impedance Data Out 2 Data Out 1 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 7 5 3 1 7 5 3 25 IS25LP128 8.6 FAST READ QUAD I/O OPERATION (FRQIO, EBh) The FRQIO instruction allows the address bits to be input four bits at a time. This may allow for code to be executed directly from the SPI in some applications. The FRQIO instruction code is followed by three address bytes (A23 – A0) and a mode byte, transmitted via the IO3, IO2, IO0 and IO1 lines, with each group of four bits latched-in during the rising edge of SCK. The address of MSB inputs on IO3, the next bit on IO2, the next bit on IO1, the next bit on IO0, and continue to shift in alternating on the four. The mode byte contains the value Ax, where x is a “don’t care” value. After four dummy clocks, the first data byte addressed is shifted out on the IO3, IO2, IO1 and IO0 lines, with each group of four bits shifted out at a maximum frequency fCT, during the falling edge of SCK. The first bit (MSB) is output on IO3, while simultaneously the second bit is output on IO2, the third bit is output on IO1, etc. Figure 8.7 illustrates the timing sequence. The first byte addressed can be at any memory location. The address is automatically incremented after each byte of data is shifted out. When the highest address is reached, the address counter will roll over to the 000000h address, allowing the entire memory to be read with a single FRQIO instruction. FRQIO instruction is terminated by driving CE# high (VIH). The device expects the next operation will be another FRQIO. It remains in this mode until it receives a Mode Reset (FFh) command. In subsequent FRDIO execution, the command code is not input, saving cycles as described in Figure 8.8. If a FRQIO instruction is issued while an Erase, Program or Write cycle is in process (WIP=1) the instruction is ignored and will not have any effects on the current cycle. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 26 IS25LP128 Figure 8.7 Fast Read Quad I/O Sequence (with command decode cycles) CE# 1 0 3 2 5 4 7 6 9 8 10 11 12 13 14 15 SCK 3-byte Address IO0 Instruction = EBh Mode Bits 20 16 12 8 4 0 4 IO1 21 17 13 9 5 1 5 IO2 22 18 14 10 6 2 6 IO3 23 19 15 11 7 3 7 CE# 16 17 18 19 20 21 22 23 24 25 26 27 ... ... SCK 4 Dummy Cycles Data Out 1 Data Out 2 Data Out 3 Data Out 4 IO0 4 0 4 0 4 0 4 0 4 IO1 5 1 5 1 5 1 6 1 5 IO2 6 2 6 2 6 2 6 2 6 IO3 7 3 7 3 7 3 7 3 7 Note: Number of dummy cycles depends on clock speed. Detailed information in Table 6.9 Read Dummy Cycles Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 27 IS25LP128 Figure 8.8 Fast Read Quad I/O Sequence (without command decode cycles) CE# 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 SCK 3-Byte Address Mode Bits 4 Dummy Cycles Data Out 1 Data Out 2 IO0 20 16 12 8 4 0 4 4 0 4 IO1 21 17 13 9 5 1 5 5 1 5 IO2 22 18 14 10 6 2 6 6 2 6 IO3 23 19 15 11 7 3 7 7 3 7 Note: Number of dummy cycles depends on clock speed. Detailed information in Table 6.9 Read Dummy Cycles Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 28 IS25LP128 8.7 PAGE PROGRAM OPERATION (PP, 02h) The Page Program (PP) instruction allows up to 256 bytes data to be programmed into memory in a single operation. The destination of the memory to be programmed must be outside the protected memory area set by the Block Protection (BP2, BP1, BP0) bits. A PP instruction which attempts to program into a page that is writeprotected will be ignored. Before the execution of PP instruction, the Write Enable Latch (WEL) must be enabled through a Write Enable (WREN) instruction. The PP instruction code, three address bytes and program data (1 to 256 bytes) are input via the Sl line. Program operation will start immediately after the CE# is brought high, otherwise the PP instruction will not be executed. The internal control logic automatically handles the programming voltages and timing. During a program operation, all instructions will be ignored except the RDSR instruction. The progress or completion of the program operation can be determined by reading the WIP bit in Status Register via a RDSR instruction. If the WIP bit is “1”, the program operation is still in progress. If WIP bit is “0”, the program operation has completed. If more than 256 bytes data are sent to a device, the address counter rolls over within the same page, the previously latched data are discarded, and the last 256 bytes are kept to be programmed into the page. The starting byte can be anywhere within the page. When the end of the page is reached, the address will wrap around to the beginning of the same page. If the data to be programmed are less than a full page, the data of all other bytes on the same page will remain unchanged. Note: A program operation can alter “1”s into “0”s, but an erase operation is required to change “0”s back to “1”s. A byte cannot be reprogrammed without first erasing the whole sector or block. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 29 IS25LP128 Figure 8.9 Page Program Sequence 5 4 7 6 8 9 10 11 28 29 30 31 32 33 34 2079 3 2078 2 2077 1 2076 0 2075 CE# SCK 1st Byte Data In 3-byte Address SI 23 Instruction = 02h ... 22 21 3 2 1 0 7 6 4 3 2 256th Byte Data In High Impedane SO 5 Figure 8.10 Page Program Sequence (QPI) CE# Mode 3 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Mode 3 SCK Mode 0 IO[3:0] Mode 0 02h A5 A4 A3 A2 Address Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 A1 A0 7:4 3:0 Data 1 7:4 3:0 Data 2 7:4 3:0 …... 7:4 3:0 Data 256 30 1 0 IS25LP128 8.8 QUAD INPUT PAGE PROGRAM OPERATION (PPQ, 32h/38h) The Quad Input Page Program instruction allows up to 256 bytes data to be programmed into memory in a single operation with four pins (IO0, IO1, IO2 and IO3). The destination of the memory to be programmed must be outside the protected memory area set by the Block Protection (BP3, BP2, BP1, BP0) bits. A Quad Input Page Program instruction which attempts to program into a page that is write-protected will be ignored. Before the execution of Quad Input Page Program instruction, the QE bit in the status register must be set to “1” and the Write Enable Latch (WEL) must be enabled through a Write Enable (WREN) instruction. The Quad Input Page Program instruction code, three address bytes and program data (1 to 256 bytes) are input via the four pins (IO0, IO1, IO2 and IO3). Program operation will start immediately after the CE# is brought high, otherwise the Quad Input Page Program instruction will not be executed. The internal control logic automatically handles the programming voltages and timing. During a program operation, all instructions will be ignored except the RDSR instruction. The progress or completion of the program operation can be determined by reading the WIP bit in Status Register via a RDSR instruction. If the WIP bit is “1”, the program operation is still in progress. If WIP bit is “0”, the program operation has completed. If more than 256 bytes data are sent to a device, the address counter rolls over within the same page, the previously latched data are discarded, and the last 256 bytes data are kept to be programmed into the page. The starting byte can be anywhere within the page. When the end of the page is reached, the address will wrap around to the beginning of the same page. If the data to be programmed are less than a full page, the data of all other bytes on the same page will remain unchanged. Note: A program operation can alter “1”s into “0”s, but an erase operation is required to change “0”s back to “1”s. A byte cannot be reprogrammed without first erasing the whole sector or block. Figure 8.11 Quad Input Page Program operation CE# 0 1 2 3 4 5 6 7 8 9 10 11 28 29 30 31 32 33 34 35 Mode 3 SCK Mode 0 IO0 Data In 1 3-Byte Address Instruction = 32h/38h 23 22 21 ... 3 2 1 0 Data In 2 4 0 4 0 IO1 5 1 5 1 IO2 6 2 6 2 IO3 7 3 7 3 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 31 IS25LP128 8.9 ERASE OPERATION The memory array of the IS25LP128 is organized into uniform 4 Kbyte sectors or 32K/64 Kbyte uniform blocks (a block consists of sixteen adjacent sectors). Before a byte is reprogrammed, the sector or block that contains the byte must be erased (erasing sets bits to “1”). In order to erase the device, there are three erase instructions available: Sector Erase (SER), Block Erase (BER) and Chip Erase (CER). A sector erase operation allows any individual sector to be erased without affecting the data in other sectors. A block erase operation erases any individual block. A chip erase operation erases the whole memory array of a device. A sector erase, block erase, or chip erase operation can be executed prior to any programming operation. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 32 IS25LP128 8.10 SECTOR ERASE OPERATION (SER, D7h/20h) A Sector Erase (SER) instruction erases a 4 Kbyte sector before the execution of a SER instruction, the Write Enable Latch (WEL) must be set via a Write Enable (WREN) instruction. The WEL bit is reset automatically after the completion of sector an erase operation. A SER instruction is entered, after CE# is pulled low to select the device and stays low during the entire instruction sequence The SER instruction code, and three address bytes are input via SI. Erase operation will start immediately after CE# is pulled high. The internal control logic automatically handles the erase voltage and timing. Refer to Figure 8.12-8.13 for the Sector Erase Sequence. During an erase operation, all instruction will be ignored except the Read Status Register (RDSR) instruction. The progress or completion of the erase operation can be determined by reading the WIP bit in the Status Register using a RDSR instruction. If the WIP bit is “1”, the erase operation is still in progress. If the WIP bit is “0”, the erase operation has been completed. Figure 8.12 Sector Erase Sequence CE# 0 1 2 3 5 4 7 6 9 8 10 11 28 29 30 31 1 0 SCK 3-byte Address SI SO Instruction = D7h/20h 23 22 ... 21 3 2 High Impedance Figure 8.13 Sector Erase Sequence (QPI) CE# 0 1 2 3 4 5 6 7 D7h/20h A5 A4 A3 A2 A1 A0 SCK IO[3:0] Address Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 33 IS25LP128 8.11 BLOCK ERASE OPERATION (BER32K:52h, BER64K:D8h) A Block Erase (BER) instruction erases a 32/64 Kbyte block of the IS25LP128. Before the execution of a BER instruction, the Write Enable Latch (WEL) must be set via a Write Enable (WREN) instruction. The WEL is reset automatically after the completion of a block erase operation. The BER instruction code and three address bytes are input via SI. Erase operation will start immediately after the CE# is pulled high, otherwise the BER instruction will not be executed. The internal control logic automatically handles the erase voltage and timing. Refer to Figure 8.14-8.17 for the Block Erase Sequence. Figure 8.14 Block Erase (64k) Sequence CE# 0 1 2 3 4 5 6 7 8 9 A23 A22 29 30 31 A1 A0 SCK SI Instruction = D8h A2 Address Figure 8.15 Block Erase (64k) Sequence (QPI) CE# 0 1 2 3 4 5 6 7 A5 A4 A3 A2 A1 A0 SCK IO[3:0] D8h Address Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 34 IS25LP128 Figure 8.16 Block Erase Sequence (32K) CE# 0 1 2 3 4 5 6 7 8 9 29 A23 A22 A2 30 31 SCK Instruction = 52h SI A1 A0 Address Figure 8.17 Block Erase (32K) Sequence (QPI) CE# 0 1 2 3 4 5 6 7 A5 A4 A3 A2 A1 A0 SCK IO[3:0] 52h Address Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 35 IS25LP128 8.12 CHIP ERASE OPERATION (CER, C7h/60h) A Chip Erase (CER) instruction erases the entire memory array of a IS25LP128. Before the execution of CER instruction, the Write Enable Latch (WEL) must be set via a Write Enable (WREN) instruction. The WEL is reset automatically after completion of a chip erase operation. The CER instruction code is input via the SI. Erase operation will start immediately after CE# is pulled high, otherwise the CER instruction will not be executed. The internal control logic automatically handles the erase voltage and timing. Refer to Figure 8.18-8.19 for the Chip Erase Sequence. Figure 8.18 Chip Erase Sequence CE # 0 1 2 3 4 5 6 7 SCK SI Instruction = C7h/60h High Impedance SO Figure 8.19 Chip Erase Sequence (QPI) CE# 0 1 SCK IO[3:0] Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 C7h/60h 36 IS25LP128 8.13 WRITE ENABLE OPERATION (WREN, 06h) The Write Enable (WREN) instruction is used to set the Write Enable Latch (WEL) bit. The WEL bit of the IS25LP128 is reset to the write –protected state after power-up. The WEL bit must be write enabled before any write operation, including sector, block erase, chip erase, page program, write status register, and write configuration register operations. The WEL bit will be reset to the write-protect state automatically upon completion of a write operation. The WREN instruction is required before any above operation is executed. Figure 8.20 Write Enable Sequence CE# 0 1 2 4 3 5 6 7 SCK SI Instruction = 06h High Impedance SO Figure 8.21 WRITE ENABLE OPERATION (QPI) CE# 0 1 SCK Instruction IO0 C4 C0 IO1 C5 C1 IO2 C6 C2 IO3 C7 C3 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 37 IS25LP128 8.14 WRITE DISABLE OPERATION (WRDI, 04h) The Write Disable (WRDI) instruction resets the WEL bit and disables all write instructions. The WRDI instruction is not required after the execution of a write instruction, since the WEL bit is automatically reset. Figure 8.22 Write Disable Sequence CE# 0 1 2 4 3 5 6 7 SCK SI Instruction = 04h High Impedance SO Figure 8.23 WRITE DISABLE OPERATION (QPI) CE# 0 1 SCK Instruction IO0 C4 C0 IO1 C5 C1 IO2 C6 C2 IO3 C7 C3 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 38 IS25LP128 8.15 READ STATUS REGISTER OPERATION (RDSR, 05h) The Read Status Register (RDSR) instruction provides access to the Status Register. During the execution of a program, erase or write status register operation, all other instructions will be ignored except the RDSR instruction, which can be used to check the progress or completion of an operation by reading the WIP bit of Status Register. Figure 8.24 Read Status Register Sequence CE# 0 1 2 3 4 5 6 9 8 7 10 11 12 13 14 15 2 1 0 SCK SI Instruction = 05h Data Out SO 7 6 5 4 3 Figure 8.25 RDSR COMMAND (READ STATUS REGISTER) OPERATION (QPI) CE# 0 1 2 3 SCK Instruction Data Out IO[3:0] Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 05h 7:4 3:0 39 IS25LP128 8.16 WRITE STATUS REGISTER OPERATION (WRSR, 01h) The Write Status Register (WRSR) instruction allows the user to enable or disable the block protection and status register write protection features by writing “0”s or “1”s into the non-volatile BP3, BP2, BP1, BP0, QE and SRWD bits. Figure 8.26 Write Status Register Sequence CE# 0 1 2 3 4 5 6 9 8 7 10 11 12 13 14 15 Mode 3 Mode 3 Mode 0 Mode 0 SCK SI Instruction = 01h 6 7 5 4 3 2 1 0 Data In High Impedance SO Figure 8.27 WRSR COMMAND (WRITE STATUS REGISTER) OPERATION (QPI) CE# 0 1 2 3 D0 SCK Instruction IO0 C4 C0 D4 IO1 C5 C1 D5 D1 IO2 C6 C2 D6 D2 IO3 C7 C3 D7 D3 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 40 IS25LP128 8.17 READ FUNCTION REGISTER OPERATION (RDFR, 48h) The Read Function Register (RDFR) instruction provides access to the Erase/Program suspend register. During the execution of a program, erase or write status register suspend, which can be used to check the suspend status. Figure 8.28 Read Function Register Sequence CE# 0 1 2 3 4 5 7 6 9 8 10 11 12 13 14 15 2 1 0 SCK SI Instruction = 48h Data Out SO High Impedance 7 6 5 4 3 MSB Figure 8.29 READ FUNCTION REGISTER OPERATION (QPI) RDFR CE# 0 1 2 3 D0 SCK Instruction IO0 C4 C0 D4 IO1 C5 C1 D5 D1 IO2 C6 C2 D6 D2 IO3 C7 C3 D7 D3 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 41 IS25LP128 8.18 WRITE FUNCTION REGISTER OPERATION (WRFR, 42h) The Write Function Register (WRFR) instruction allows the user to lock the information row by bit 0. (IR lock) Figure 8.30 Write Function Register Sequence CE# 0 1 2 3 4 5 6 8 7 9 10 11 12 13 14 15 Mode 3 Mode 3 Mode 0 Mode 0 SCK SI Instruction = 42h 6 7 5 4 3 2 1 0 Data In High Impedance SO Figure 8.31 WRFR COMMAND (WRITE Function REGISTER) OPERATION (QPI) CE# 0 1 2 3 D0 SCK Instruction IO0 C4 C0 D4 IO1 C5 C1 D5 D1 IO2 C6 C2 D6 D2 IO3 C7 C3 D7 D3 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 42 IS25LP128 8.19 ENTER QUAD PERIPHERAL INTERFACE (QPI) MODE OPERATION (QIOEN,35h; QIODI,F5h) The Enter Quad I/O (QIOEN) instruction, 35h, enables the Flash device for QPI bus operation. Upon completion of the instruction, all instructions thereafter will be 4-bit multiplexed input/output until a power cycle or a “Exit Quad I/O instruction” instruction. Figure 8.32 Enter Quad Peripheral Interface OPERATION (QPI) CE# 0 1 2 4 3 5 6 7 SCK SI Instruction = 35h High Impedance SO Figure 8.33 Exit Quad Peripheral Interface (QPI) mode OPERATION The Exit Quad I/O instruction, F5h, resets the device to 1-bit SPI protocol operation. To execute a Exit Quad I/O operation, the host drives CE# low, sends the Exit Quad I/O command cycle then, drives CE# high. The device just accepts SQI (2 clocks) command cycles. CE# 0 1 SCK Instruction = F5h IO0 C4 C0 IO1 C5 C1 IO2 C6 C2 IO3 C7 C3 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 43 IS25LP128 8.20 PROGRAM/ERASE SUSPEND & RESUME The device allows the interruption of Sector-Erase, Block-Erase or Page-Program operations to conduct other operations. B0h command for suspend and 30h for resume will be used. (SPI/QPI all acceptable) Function register bit2 (PSUS) and bit3 (ESUS) are used to check whether or not the device is in suspend mode. Suspend to read ready timing: 100µs. Resume to another suspend timing: 400µs (recommendation). PROGRAM/ERASE SUSPEND DURING SECTOR-ERASE OR BLOCK-Erase (PERSUS 75h/B0h) After erase suspend, WEL bit will be disabled, therefore only read related, resume and reset commands will be accepted (03h, 0Bh, BBh, EBh, 05h, ABh, 30h, 9Fh, ABh, 90h, 4Bh, 00h, 66h, 99h, AFh, C0h). To execute a Program/Erase Suspend operation, the host drives CE# low, sends the Program/Erase Suspend command cycle (B0H), then drives CE# high. The Function register indicates that the erase has been suspended by changing the ESUS bit from ‘0’ to ‘1,’ but the device will not accept another command until it is ready. To determine when the device will accept a new command, poll the WIP bit in the Status register or wait tSUS. When ESUS bit is issued, the Write Enable Latch (WEL) bit will be reset. PROGRAM/ERASE SUSPEND DURING PAGE PROGRAMMING (PERSUS 75h/B0h) Program suspend allows the interruption of all program operations. After a program suspend command, WEL bit will be disabled, only read related, resume and reset command can be accepted (03h, 0Bh, BBh, EBh, 05h, ABh, 30h, 9Fh, ABh, 90h, 4Bh, 00h, 66h, 99h, AFh, C0h). To execute a Program/Erase Suspend operation, the host drives CE# low, sends the Program/Erase Suspend command cycle (B0H), then drives CE# high. The Function register indicates that the programming has been suspended by changing the PSUS bit from ‘0’ to ‘1,’ but the device will not accept another command until it is ready. To determine when the device will accept a new command, poll the WIP bit in the Status register or wait tSUS. PROGRAM/ERASE RESUME (PERRSM 7A/30h) Program/Erase Resume restarts a Program/Erase command that was suspended, and changes the suspend status bit in the (ESUS or PSUS bits) back to ‘0’. To execute a Program/Erase Resume operation, the host drives CE# low, sends the Program/Erase Resume command cycle (30H), then drives CE# high. A cycle is two nibbles long, most significant nibble first. To determine if the internal, self-timed Write operation completed, poll the WIP bit in the Status register, or wait the specified time tSE, tBE or tPP for Sector- Erase, Block-Erase, or Page-Programming, respectively. The total write time before suspend and after resume will not exceed the uninterrupted write times tSE, tBE or tPP. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 44 IS25LP128 8.21 DEEP POWER DOWN (DP, B9h) The Deep Power-down (DP) instruction is for setting the device on the minimizing the power consumption (enter into Power-Down mode), the standby current is reduced from Isb1 to Isb2). During the Power-down mode, the device is not active and all Write/Program/Erase instructions are ignored. The instruction is initiated by driving the CE# pin low and shifting the instruction code “B9h” as show in the figure 8.34. The CE# pin must be driven high after the instruction has been latched. If this is not done the Power-Down will not be executed. After CE# pin driven high, the power-down state will entered within the time duration of tDP. While in the power-down state only the Release from Power-down / RDID instruction, which restores the device to normal operation, will be recognized. All other instructions are ignored. This includes the Read Status Register instruction, which is always available during normal operation. Ignoring all but one instruction makes the Power Down state a useful condition for securing maximum write protection. It can support in SPI and QPI mode. Figure 8.34 Enter Deep Power Down Mode Operation. (SPI) CE# tDP 0 1 2 3 4 5 6 7 SCK SI ... ... Instruction = B9h Figure 8.35 Deep Power Down Sequence (QPI) CE# 0 1 tDP SCK Instruction IO0 C4 C0 IO1 C5 C1 IO2 C6 C2 IO3 C7 C3 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 45 IS25LP128 8.22 RELEASE DEEP POWER DOWN (RDPD, ABh) The Release from Power-down /read Device ID instruction is a multi-purpose instruction. To release the device from the power-down state Mode, the instruction is issued by driving the CE# pin low, shifting the instruction code “ABh” and driving CE# high as shown in Figure 8.36, 8.37 Release from power-down will take the time duration of tRES1 before the device will resume normal operation and other instructions are accepted. The CE# pin must remain high during the tRES1 time duration. If the Release from Power-down / RDID instruction is issued while an Erase, Program or Write cycle is in process (when WIP equals 1) the instruction is ignored and will not have any effects on the current cycle. Figure 8.36 Release Power Down Sequence (SPI) CE# tRES1 0 1 2 3 4 5 6 7 SCK SI ... ... Instruction = ABh Figure 8.37 Release Power Down Sequence (QPI) CE# 0 1 tRES1 SCK Instruction IO0 C4 C0 IO1 C5 C1 IO2 C6 C2 IO3 C7 C3 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 46 IS25LP128 8.23 SET READ PARAMETERS OPERATION (SRP, C0h) Set Read Operational Driver Strength This device supports configurable Operational Driver Strengths in both SPI and QPI mode by setting three bits within the READ Register (ODS0, ODS1, ODS3). To set the ODS bits the SRP operation (C0h) instruction is required. The device’s driver strength can be reduced as low as 12.50% of full drive strength. Details regarding the driver strength can be found in table 6.10. Note: The default driver strength is set to 50% Figure 8.38 Set Read Parameters Operation. CE# 0 1 2 3 4 5 6 9 8 7 10 11 12 13 14 15 Mode 3 Mode 3 Mode 0 Mode 0 SCK SI Instruction = C0h 6 7 5 4 3 2 1 0 Data In High Impedance SO Figure 8.39 Set Read Parameters Operation. (QPI) CE# 0 1 2 3 D0 SCK Instruction IO0 C4 C0 D4 IO1 C5 C1 D5 D1 IO2 C6 C2 D6 D2 IO3 C7 C3 D7 D3 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 47 IS25LP128 Read with “8/16/32/64-Byte Wrap Around” The device is capable of burst read with wrap around in both SPI and QPI mode. The size of burst length is configurable by using P0, P1, and P2 bits in READ register. P2 bit (Wrap enable) enables the burst mode feature. P0 and P1 define the size of burst. Burst of 8, 16, 32, and 64 bytes are supported. In the default, address increases by one up to whole array. By setting the burst length, the data being accessed can be limited to the length of burst boundary inside of 256 byte page. The first output will be the data at the initial address which is specified in the instruction. Following data will come out from the next address inside of burst boundary. Once the address reaches the end of boundary, it will automatically move to the first address of the boundary. CS# high will terminate the command. For example, if burst length of 8 and initial address being applied is 0h, following byte output will be from address 00h and continue to 01h,..,07h, 00h, 01h… until CS# terminates the operation. If burst length of 8 and initial address being applied is FEh(254d), following byte output will be from address FEh and continue to FFh, F8h, F9h, FAh, FBh, FCh, FDh, and repeat from FEh until CS# terminates the operation. The command, “SET READ PARAMETERS OPERATION (C0h)”, is used to configure the Burst length. If the following data input is one of “00h”,”01h”,”02h”, and ”03h”, the device will be in the default operation mode. It will be continuous burst read of whole array. If the following data input is one of “04h”,”05h”,”06h”, and ”07h”, the device will set the burst length as 8,16,32 and 64 respectively. To exit the burst mode, another “C0h” command is necessary to set P2 to 0. Otherwise, the burst mode will be retained until power down or reset operations. To change burst length, another “C0h” command should be executed to set P0 and P1 (Detailed information in Table 6.7 Burst Length Data). All read commands operate in burst mode once the READ register is set to enable burst mode. Refer to Figures 8.38 and 8.39 for instruction sequence. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 48 IS25LP128 8.24 READ PRODUCT IDENTIFICATION (RDID, ABh) The Release from Power-down /read Device ID instruction is a multi-purpose instruction. It can support both SPI and QPI mode. The Read Product Identification (RDID) instruction is for reading out the old style of 8-bit Electronic Signature, whose values are shown as table of ID Definitions. The RDID instruction code is followed by three dummy bytes, each bit being latched-in on SI during the rising SCK edge. Then the Device ID is shifted out on SO with the MSB first, each bit been shifted out during the falling edge of SCK. The RDID instruction is ended by CE# going high. The Device ID (ID7-ID0) outputs repeatedly if additional clock cycles are continuously sent on SCK while CE# is at low. Table 8.3 Product Identification Manufacturer ID (MF7-MF0) ISSI Serial Flash 9Dh Instruction ABh 90h 9Fh Device Density Device ID (ID7-ID0) Memory Type + Capacity (ID15-ID0) 128Mb 17h 6018h Figure 8.40 Read Product Identification Sequence CE# Mode 3 0 1 8 7 ... ……….. 31 32 ……….. 38 39 ……….. 46 47 ……….. 54 Mode 3 SCK Mode 0 Mode 0 Instruction = ABh SI 3 Dummy Cycles Device ID (ID7-ID0) SO Device ID (ID7-ID0) Device ID (ID7-ID0) Figure 8.41 Read Product Identification Sequence (QPI) CE# Mode 3 0 1 2 3 4 5 6 7 8 9 10 11 Mode 3 SCK Mode 0 Instruction Data IO[3:0] ABh 7:4 Mode 0 3:0 3 Dummy Cycles Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 Device ID (ID7-ID0) Device ID (ID7-ID0) 49 IS25LP128 8.25 READ PRODUCT IDENTIFICATION BY JEDEC ID OPERATION (RDJDID, 9Fh) The JEDEC ID READ instruction allows the user to read the manufacturer and product ID of devices. Refer to Table 8.3 Product Identification for Manufacturer ID and Device ID. After the JEDEC ID READ command (9Fh in SPI mode, AFh in QPI mode) is input, the Manufacturer ID is shifted out MSB first followed by the 2-byte electronic ID (ID15-ID0) that indicates memory type and density, one bit at a time. Each bit is shifted out during the falling edge of SCK. If CE# stays low after the last bit of the 2-byte electronic ID, the Manufacturer ID and 2byte electronic ID will loop until CE# is pulled high. 9Dh, 60h, and 18h should be the output. Figure 8.42 Read Product Identification by JEDEC ID READ Sequence CE# 0 Mode 3 1 8 7 ... ……….. 15 16 ……….. 23 24 ……….. 31 32 ……….. Mode 3 SCK Mode 0 Mode 0 Instruction = 9Fh SI SO Manufacture ID MF7-MF0 (MF7-MF0) Memory Type ID15-ID8 (ID15- ID8) Capacity ID7-ID0 (ID7-ID0) …….. Figure 8.43 RDIDQ COMMAND (Read ID in QPI Mode) OPERATION CE# Mode 3 0 1 2 3 4 5 6 7 Mode 3 SCK Mode 0 IO[3:0] Mode 0 Instruction 9Fh 7:4 3:0 7:4 3:0 Manu. ID1 Mem. Type MF7-MF0 ID15-ID8 7:4 3:0 Capacity ID7-ID0 Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 50 IS25LP128 8.26 READ DEVICE MANUFACTURER AND DEVICE ID OPERATION (RDMDID, 90h) The Read Product Identification (RDID) instruction allows the user to read the manufacturer and product ID of the devices. Refer to Table 8.3 Product Identification for manufacturer ID and device ID. The RDID instruction code is followed by two dummy bytes and one byte address (A7~A0), each bit being latched-in on SI during the rising edge of SCK. If one byte address is initially set to A0 = 0, then the manufacturer ID (9Dh) is shifted out on SO with the MSB first followed by the device ID7- ID0. Each bit shifted out during the falling edge of SCK. If one byte address is initially set to A0 = 1, then Device ID7-ID0 will be read first followed by the Manufacture ID (9Dh). The manufacture and device ID can be read continuously alternating between the two until CE# is driven high. Figure 8.44 Read Product Identification by RDMDID READ Sequence CE# 0 1 ... 7 8 ……….. 31 32 ……….. 39 40 ……….. 47 48 ……….. 55 Mode 3 Mode 3 Mode 0 Mode 0 SCK SI Instruction = 90h 3-byte Address SO Manufacture ID MF7-MF0 Device ID ID7-ID0 Manufacture ID MF7-MF0 Notes: (1) ADDRESS A0 = 0, will output the 1-byte Manufacture ID (MF7-MF0) -> 1-byte device (ID7-ID0) ADDRESS A0 = 1, will output the 1-byte device (ID7-ID0) -> 1-byte Manufacture ID (MF7-MF0) (2) The Manufacture and Device ID can be read continuously and will alternate from one to the other until CE# pin is pulled high. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 51 IS25LP128 8.27 READ UNIQUE ID NUMBER (RDUID, 4Bh) The Read Unique ID Number (RDUID) instruction accesses a factory-set read-only 16-byte number that is unique to the device. The Id number can be used in conjunction with user software methods to help prevent copying or cloning of a system. The RDUID instruction is instated by driving the CE# pin low and shifting the instruction code (4Bh) followed by 3 address bytes and a dummy byte. After which, the 16-byte ID is shifted out on the falling edge of SCK as shown below. Note: 16 bytes of data will repeat as long as CE# is low and SCK is toggling. Figure 8.45 RDUID COMMAND OPERATION CE# Mode 3 0 1 ... 7 8 ……….. 31 32 ……….. 39 40 ……….. 47 48 Mode 3 SCK Mode 0 Mode 0 Instruction = 4Bh SI 3-byte Address Dummy Cycle SO Data Out …... A[23:16] A[15:9] A[8:4] A[3:0] XXh XXh 00h 0h Byte address XXh XXh 00h 1h Byte address XXh XXh 00h 2h Byte address XXh XXh 00h … Table 8.4 Unique ID Addressing XXh XXh 00h Fh Byte address Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 52 IS25LP128 8.28 READ SFDP OPERATION (RDSFDP, 5Ah) The Serial Flash Discoverable Parameter (SFDP) standard provides a consistent method of describing the functional and feature capabilities of serial Flash devices in a standard set of internal parameter tables. These parameter tables can be interrogated by host system software to enable adjustments needed to accommodate divergent features from multiple vendors. The concept is similar to the one found in the Introduction of JEDEC Standard, JESD68 on CFI. The sequence of issuing RDSFDP instruction is same as FAST_READ: CE# goes low → send RDSFDP instruction (5Ah) → send 3 address bytes on SI pin → send 1 dummy byte on SI pin → read SFDP code on SO → to end RDSFDP operation can use CE# to high at any time during data out. Refer to ISSI’s Application note for SFDP table. The data at the addresses that are not specified in SFDP table is undefined. Figure 8.46 RDSFDP COMMAND (Read SFDP) OPERATION CE# 0 Mode 3 1 ... 7 8 ……….. 31 32 ……….. 39 40 ……….. 47 48 Mode 3 SCK Mode 0 SI Mode 0 Instruction = 5Ah 3-byte Address SO Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 Dummy Cycle Data Out …... 53 IS25LP128 8.29 NO OPERATION (NOP, 00h) The No Operation command only cancels a Reset Enable command. NOP has no impact on any other command. It can use in the SPI and QPI mode. To execute a NOP, the host drives CE# low, sends the NOP command cycle (00H), then drives CE# high. 8.30 SOFTWARE RESET (RESET-ENABLE (RSTEN, 66h) AND RESET (RST, 99h) The Reset operation is used as a system (software) reset that puts the device in normal operating mode. This operation consists of two commands: Reset-Enable (RSTEN) and Reset (RST). The Reset operation requires the Reset-Enable command followed by the Reset command. Any command other than the Reset command after the Reset-Enable command will disable the Reset-Enable. Execute the CE# pin low sends the Reset-Enable command (66h), and drives CE# high. Next, the host drives CE# low again, sends the Reset command (99h), and drives CE# high. A device reset during an active Program or Erase operation aborts the operation, which can cause the data of the targeted address range to be corrupted or lost. Depending on the prior operation, the reset timing may vary. Recovery from a Write operation requires more latency time than recovery from other operations. Figure 8.47 SOFTWARE RESET ENABLE, SOFTWARE RESET OPERATIONS (RSTEN, 66h + RST, 99h) CE# Mode 3 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Mode 3 SCK Mode 0 SI SO Mode 0 Instruction = 66h Instruction = 99h High Impedance Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 54 IS25LP128 8.31 MODE RESET OPERATION (RSTM, FFh) The Mode Reset command is used to conclude subsequent FRDIO and FRQIO operations. It resets the Mode bits to a value that is not Ax. It should be executed after an FRDIO or FRQIO operation, and is recommended also as the first command after a system reset. The timing sequence is different depending whether the MR command is used after an FRDIO or FRQIO, as shown in Figure 8.48 Figure 8.48 Mode Reset Command Mode Reset for Dual I/O Mode Reset for Quad I/O CE# Mode 3 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Mode 3 SCK Mode 0 SI SO Mode 0 Instruction = FFh Instruction = FFh High Impedance 8.32 SECURITY INFORMATION ROW The security information row is comprised of an additional 4 x 256 bytes of programmable information. The security bits can be reprogrammed by the user. Any program security instruction issued while an erase, program or write cycle is in progress is rejected without having any effect on the cycle that is in progress. Table 8.5 Information Row Address Address Assignment IRL0(Information row lock0) IRL1 IRL2 IRL3 A[23:16] 00h 00h 00h 00h A[15:8] 00h 10h 20h 30h A[7:0] Byte address Byte address Byte address Byte address Bit 7~4 of the Function Register is used to permanently lock the programmable memory array. When Function Register bit IRLx = ’0’, the 256 bytes of the programmable memory array can be programmed. When Function Register bit IRLx = ‘1’, the 256 bytes of the programmable memory array function as read only. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 55 IS25LP128 8.33 INFORMATION ROW ERASE OPERATION (IRER, 64h) Information Row Erase instruction erases the Information Row x (x : 0~3) array , the Write Enable Latch (WEL) must be set via a Write Enable (WREN) instruction. The WEL bit is reset automatically after the completion of sector an erase operation. A IRER instruction is entered, after CE# is pulled low to select the device and stays low during the entire instruction sequence The IRER instruction code, and three address bytes are input via SI. Erase operation will start immediately after CE# is pulled high. The internal control logic automatically handles the erase voltage and timing. Refer to Figure 8.49 for IRER Sequence. Figure 8.49 IRER COMMAND (Information Row Erase) OPERATION CE# 0 1 2 3 4 5 6 7 8 9 10 11 28 29 30 31 Mode 3 Mode 3 SCK Mode 0 SI SO Mode 0 3-byte Address Instruction = 64h 23 22 21 ... 3 2 1 0 High Impedance Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 56 IS25LP128 8.34 INFORMATION ROW PROGRAM OPERATION (IRP, 62h) The Information Row Program (IRP) instruction allows up to 1024 bytes, 4x256 bytes, data to be programmed into memory in a single operation. Before the execution of PP instruction, the Write Enable Latch (WEL) must be enabled through a Write Enable (WREN) instruction. The IRP instruction code, three address bytes and program data (1 to 256 bytes) are input via the Sl line. Program operation will start immediately after the CE# goes high, otherwise the IRP instruction will not be executed. The internal control logic automatically handles the programming voltages and timing. During a program operation, all instructions will be ignored except the RDSR instruction. The progress or completion of the program operation can be determined by reading the WIP bit in Status Register via a RDSR instruction. If the WIP bit is “1”, the program operation is still in progress. If WIP bit is “0”, the program operation has completed. If more than 1024 bytes data are sent to a device, the address counter rolls over within the same page. The previously latched data are discarded and the last 1024 bytes data are kept to be programmed into the page. The starting byte can be anywhere within the page. When the end of the page is reached, the address will wrap around to the beginning of the same page. If the data to be programmed are less than a full page, the data of all other bytes on the same page will remain unchanged. Note: A program operation can alter “1”s into “0”s, but an erase operation is required to change “0”s back to “1”s. A byte cannot be reprogrammed without first erasing the whole sector or block. Figure 8.50 IRP COMMAND (Information Row Program) OPERATION CE# Mode 3 SCK Mode 0 SI High Impedance SO Instruction = 62h 24 Cycles (24 ADD input) CE# Mode 3 SCK st Mode 0 th 1 Byte Data In 256 Byte Data In SI High Impedance SO Data In Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 57 IS25LP128 8.35 INFORMATION ROW READ OPERATION (IRRD, 68h) The IRRD instruction is used to read memory data at up to a 133MHz clock. The IRRD instruction code is followed by three address bytes (A23 - A0) and a dummy byte (8 clocks), transmitted via the SI line, with each bit latched-in during the rising edge of SCK. Then the first data byte addressed is shifted out on the SO line, with each bit shifted out at a maximum frequency fCT, during the falling edge of SCK. The address is automatically incremented after each byte of data is shifted out. When the highest address is reached, the address counter will roll over to the 000000h address, allowing the entire memory to be read with a single IRRD instruction. The IRRD instruction is terminated by driving CE# high (VIH). If a IRRD instruction is issued while an Erase, Program or Write cycle is in process (WIP=1) the instruction is ignored and will not have any effects on the current cycle Figure 8.51 IRRD COMMAND (Information Row Read) OPERATION CE# Mode 3 0 1 ... 7 8 ……….. 31 32 ……….. 39 40 ……….. 47 48 ... Mode 3 SCK Mode 0 SI SO Mode 0 Instruction = 68h 3-byte Address Dummy Byte High Impedance Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 Data Out …... 58 IS25LP128 8.36 FAST READ DTR MODE OPERATION (FRDTR, 0DH) The FRDTR instruction is for doubling reading data out, signals are triggered on both rising and falling edge of clock. The address is latched on both rising and falling edge of SCK, and data of each bit shifts out on both rising and falling edge of SCK at a maximum frequency fC2. The 2-bit address can be latched-in at one clock, and 2-bit data can be read out at one clock, which means one bit at rising edge of clock, the other bit at falling edge of clock. The first address byte can be at any location. The address is automatically increased to the next higher address after each byte data is shifted out, so the whole memory can be read out at a single FRDTR instruction. The address counter rolls over to 0 when the highest address has been reached. The sequence of issuing FRDTR instruction is: CE# goes low → sending FRDTR instruction code (1bit per clock) → 3-byte address on SI (2-bit per clock) → 6-dummy clocks (default) on SI → data out on SO (2-bit per clock) → to end FRDTR operation can use CE# to high at any time during data out. (Please refer to Figure 8.52) While Program/Erase/Write Status Register cycle is in progress, FRDTR instruction is rejected without any impact on the Program/Erase/Write Status Register current cycle. Figure 8.52 FRDTR COMMAND (Fast Read DTR Mode) OPERATION CE# 0 7 8 19 23 24 25 26 27 SCK SI SO 0Dh A23A23 A1 A0 12 Cycles (24 Address Input) 4 Dummy Cycles Data 1 Data 2 D7 D6 D5 D4 D3 D2 D1 D0 D7… Note: Number of dummy cycles depends on clock speed. Detailed information in Table 6.9. Read Dummy Cycles Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 59 IS25LP128 8.37 FAST READ DUAL IO DTR MODE OPERATION (FRDDTR, BDH) The FRDDTR instruction enables Double Transfer Rate throughput on dual I/O of Serial Flash in read mode. The address (interleave on dual I/O pins) is latched on both rising and falling edge of SCK, and data (interleave on dual I/O pins) shift out on both rising and falling edge of SCK at a maximum frequency fT2. The 4-bit address can be latched-in at one clock, and 4-bit data can be read out at one clock, which means two bits at rising edge of clock, the other two bits at falling edge of clock. The first address byte can be at any location. The address is automatically increased to the next higher address after each byte data is shifted out, so the whole memory can be read out at a single FRDDTR instruction. The address counter rolls over to 0 when the highest address has been reached. Once writing FRDDTR instruction, the following address/dummy/ data out will perform as 4-bit instead of previous 1-bit. The sequence of issuing FRDDTR instruction is: CE# goes low → sending FRDDTR instruction (1-bit per clock) → 24-bit address interleave on SIO1 & SIO0 (4-bit per clock) → 6-bit dummy clocks on SIO1 & SIO0 → data out interleave on SIO1 & SIO0 (4-bit per clock) → to end FRDDTR operation can use CE# to high at any time during data out (Please refer to Figure 8.53 for 2 x I/O Double Transfer Rate Read Mode Timing Waveform). While Program/Erase/Write Status Register cycle is in progress, FRDDTR instruction is rejected without any impact on the Program/Erase/Write Status Register current cycle. Figure 8.53 FRDDTR COMMAND (Fast Read Dual IO DTR Mode) OPERATION CE# 0 7 8 13 17 18 19 20 21 SCK Mode Bits SI BDh A22A20 A2 A0 6 6 Cycles (24 Address Input) SO A23 A21 A3 A1 7 D6 D4 D2 D0 D6 D4 D2 D0 D6… 4 4 Dummy Cycles 5 Data 1 Data 2 Data 3 D7 D5 D3 D1 D7 D5 D3 D1 D7… Note: Number of dummy cycles depends on clock speed. Detailed information in Table 6.9. Read Dummy Cycles Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 60 IS25LP128 8.38 FAST READ QUAD IO DTR MODE OPERATION (FRQDTR, EDH) The FRQDTR instruction enables Double Transfer Rate throughput on quad I/O of Serial Flash in read mode. A Quad Enable (QE) bit of status Register must be set to "1" before sending the FRQDTR instruction. The address (interleave on 4 I/O pins) is latched on both rising and falling edge of SCK, and data (interleave on 4 I/O pins) shift out on both rising and falling edge of SCK at a maximum frequency fQ2. The 8-bit address can be latched-in at one clock, and 8-bit data can be read out at one clock, which means four bits at rising edge of clock, the other four bits at falling edge of clock. The first address byte can be at any location. The address is automatically increased to the next higher address after each byte data is shifted out, so the whole memory can be read out at a single FRQDTR instruction. The address counter rolls over to 0 when the highest address has been reached. Once writing FRQDTR instruction, the following address/dummy/data out will perform as 8-bit instead of previous 1-bit. The sequence of issuing FRQDTR instruction is: CE# goes low → sending FRQDTR instruction (1-bit per clock) → 24-bit address interleave on SIO3, SIO2, SIO1 & SIO0 (8-bit per clock) → 8 dummy clocks → data out interleave on SIO3, SIO2, SIO1 & SIO0 (8-bit per clock) → to end FRQDTR operation can use CE# to high at any time during data out. Another sequence of issuing enhanced mode of FRQDTR instruction especially useful in random access is: CE# goes low → sending FRQDTR instruction (1-bit per clock) → 3-bytes address interleave on SIO3, SIO2, SIO1 & SIO0 (8-bit per clock) → performance enhance toggling bit P[7:0] → 7 dummy clocks → data out(8-bit per clock) still CE# goes high → CE# goes low (eliminate 4 Read instruction) → 24-bit random access address (Please refer to Figure 8.54 for 4x I/O Double Transfer Rate read enhance performance mode timing waveform). While Program/Erase/Write Status Register cycle is in progress, FRQDTR instruction is rejected without any impact on the Program/Erase/Write Status Register current cycle. Figure 8.54 FRQDTR COMMAND (Fast Read Quad IO DTR Mode) OPERATION CE# 0 7 8 10 14 15 16 SCK Mode Bits IO0 EDh A20A16 A12 A8 A4 A0 4 3 Cycles (24 Address) D4 D0 D4 D0 D4 4 Dummy Cycles Data 1 Data 2 IO1 A21 A17A13 A9 A5 A1 5 D5 D1 D5 D1 D5 IO2 A22 A18A14 A10 A6 A2 6 D6 D2 D6 D2 D6 IO3 A23 A19A15 A11 A7 A3 7 D7 D3 D7 D3 D7 Note: Number of dummy cycles depends on clock speed. Detailed information in Table 6.9. Read Dummy Cycles Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 61 IS25LP128 8.39 SECTOR LOCK/UNLOCK FUNCTIONS SECTOR UNLOCK OPERATION (SECUNLOCK, 26h) The Sector Unlock command allows the user to select a specific sector to allow program and erase operations. This instruction is effective when the blocks are designated as write-protected through the BP0, BP1, BP2 and BP3 bits in the status register. Only one sector can be enabled at any time. To enable a different sector, a previously enabled sector must be disabled by executing a Sector Lock command. The instruction code is followed by a 24-bit address specifying the target sector, but A0 through A11 are not decoded. The remaining sectors within the same block remain in read-only mode. In the Sector Unlock procedure, [A11:A0] need to be “0”, in order for the unlock procedure to be completed. The chip will regard anything else as an illegal command. Figure 8.55 Sector Unlock Sequence CE# 0 1 2 3 4 5 6 7 8 9 10 11 28 29 30 31 Mode 3 Mode 3 SCK Mode 0 SI SO Mode 0 3-byte Address Instruction = 26h 23 22 21 ... 3 2 1 0 High Impedance Notes: 1. If the number of clock cycles do not match 8 cycles (command) + 24 clocks (address), the command will be ignored. 2. WREN (06h) must be executed before sector unlock instructions. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 62 IS25LP128 SECTOR LOCK OPERATION (SECLOCK, 24h) The Sector Lock command reverses the function of the Sector Unlock command. The instruction code does not require an address to be specified, as only one sector can be enabled at a time. The remaining sectors within the same block remain in read-only mode. Figure 8.56 Sector Lock Sequence CE# Mode 3 0 1 2 3 4 5 6 7 Mode 3 SCK Mode 0 Mode 0 SI SO Instruction = 24h High Impedance Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 63 IS25LP128 9. ELECTRICAL CHARACTERISTICS 9.1 ABSOLUTE MAXIMUM RATINGS (1) o Storage Temperature o -55 C to +150 C Surface Mount Lead Soldering Temperature Standard Package 240oC 3 Seconds Lead-free Package 260oC 3 Seconds Input Voltage with Respect to Ground on All Pins -0.5V to VCC + 0.5V All Output Voltage with Respect to Ground -0.5V to VCC + 0.5V VCC -0.5V to +6.0V Note: 1. Applied conditions greater than those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 9.2 OPERATING RANGE Part Number Operating Temperature (Extended Grade) Operating Temperature (Automotive Grade A1) Operating Temperature (Automotive Grade A2) Operating Temperature (Automotive Grade A3) VCC Power Supply IS25LP128 -40°C to 105°C -40°C to 85°C -40°C to 105°C -40°C to 125°C 2.3 V (VMIN) – 3.6 V (VMAX) 9.3 DC CHARACTERISTICS (Under operating range) Symbol Max Units VCC Active Read Current VCC = VMAX at 50MHz, SO = Open 10 15 mA ICC2 VCC Program/Erase Current VCC = VMAX at 50MHz, SO = Open 25 40 mA ISB1 VCC Standby Current CMOS VCC = VMAX, CE# = VCC 10 50 A ISB2 Deep power down current VCC = VMAX, CE# = VCC 5 20 A ILI Input Leakage Current VIN = 0V to VCC 1 A Output Leakage Current VIN = 0V to VCC 1 A VIL (1) Condition Min Typ(2) ICC1 ILO Parameter Input Low Voltage -0.5 0.3VCC V VIH (1) Input High Voltage 0.7VCC VCC + 0.3 V VOL Output Low Voltage 0.2 V 2.3V < VCC < 3.6V IOL = 100 µA VOH Output High Voltage VCC - 0.2 V IOH = -100 A Notes: 1. Maximum DC voltage on input or I/O pins is VCC + 0.5V. During voltage transitions, input or I/O pins may overshoot VCC by + 2.0 V for a period of time not to exceed 20ns. Minimum DC voltage on input or I/O pins is -0.5V. During voltage transitions, input or I/O pins may undershoot GND by -2.0 V for a period of time not to exceed 20ns. 2. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC (Typ), TA=25°C Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 64 IS25LP128 9.4 AC MEASUREMENT CONDITIONS Symbol Parameter Min Max Units CL Load Capacitance up to 104MHz 30 pF CL Load Capacitance up to 133MHz 15 pF TR,TF Input Rise and Fall Times 5 ns VIN Input Pulse Voltages 0.2VCC to 0.8VCC V VREFI Input Timing Reference Voltages 0.3VCC to 0.7VCC V VREFO Output Timing Reference Voltages 0.5VCC V Figure9.1 Output test load & AC measurement I/O Waveform 0.8VCC Input 1.8k VCC/2 AC Measurement Level 0.2VCC OUTPUT PIN 1.2k 15/30pf Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 65 IS25LP128 9.5 AC CHARACTERISTICS (Under operating range, refer to section 9.4 for AC measurement conditions) Symbol fC Parameter Clock Frequency for fast read mode: SPI, Dual, Dual I/O, Quad I/O, and QPI. Clock Frequency for fast read DTR: SPI DTR, Dual DTR, Dual I/O DTR, Quad I/O DTR, and QPI DTR. Clock Frequency for read mode SPI 50 MHz tRI Input Rise Time 8 ns tFI Input Fall Time 8 ns tCKH SCK High Time 4 ns tCKL SCK Low Time 4 ns tCEH CE# High Time 7 ns tCS CE# Setup Time 5 ns tCH CE# Hold Time 5 ns tDS Data In Setup Time tDH Data in Hold Time fCT fC2, fT2, fQ2 tV Normal Mode DTR Mode Normal Mode DTR Mode Min Typ Max Units 0 133 MHz 0 66 MHz 0 2 ns 1.5 ns 2 ns 1.5 ns Output Valid @ 133MHz Output Valid @ 104MHz 7 ns 8 ns tOH Output Hold Time Normal Mode 2 ns tDIS Output Disable Time tHD Output Hold Time 2 ns tHLCH HOLD Active Setup Time relative to SCK 5 ns tCHHH HOLD Active Hold Time relative to SCK 5 ns tHHCH HOLD Not Active Setup Time relative to SCK 5 ns tCHHL HOLD Not Active Hold Time relative to SCK 5 tLZ HOLD to Output Low Z 12 ns tHZ HOLD to Output High Z 12 ns 8 ns ns Sector Erase Time (4Kbyte) 45 300 ms Block Erase Time (32Kbyte) 0.15 0.75 s Block Erase time (64Kbyte) 0.3 1.5 s Chip Erase Time (128Mb) 30 90 s tPP Page Program Time 0.2 1.0 ms tVCE Vcc(min) to CE# Low tres1 Release deep power down tDP Deep power down tW Write Status Register time tSUS Suspend to read ready tSRST Software Reset cover time tEC Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 1 ms 3 2 20 66 µs 3 µs 15 ms 100 µs 100 µs IS25LP128 9.6 SERIAL INPUT/OUTPUT TIMING Figure 9.2 SERIAL INPUT/OUTPUT TIMING (Normal Mode) (1) tCEH CE# tCH tCS tCKH SCK tDS SI tCKL tDH VALID IN VALID IN tV SO HI-Z tOH tDIS HI-Z VALID OUTPUT Note1. For SPI Mode 0 (0,0) Figure 9.3 SERIAL INPUT/OUTPUT TIMING (DTR Mode) (1) tCEH CE# tCS tCH tCKH SCK tDS SI tCKL tDH VALID IN VALID IN VALID IN tV SO HI-Z tV Output tOH tDIS HI-Z Output Note1. For SPI Mode 0 (0,0) Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 67 IS25LP128 Figure 9.4 HOLD TIMING CE# tHLCH tCHHL tHHCH SCK tCHHH tHZ tLZ SO SI HOLD# Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 68 IS25LP128 9.7 POWER-UP AND POWER-DOWN At Power-up and Power-down, the device must be NOT SELECTED until Vcc reaches at the right level. (Adding a simple pull-up resistor on CE# is recommended.) Power up timing VCC VCC(max) All Write Commands are Rejected Chip Selection Not Allowed VCC(min) Reset State tVCE V(write inhibit) Read Access Allowed Device fully accessible tPUW Symbol Parameter tVCE(1) Vcc(min) to CE# Low tPUW(1) Power-up time delay to write instruction VWI(1) Write Inhibit Voltage Note1. These parameters are characterized and are not 100% tested. Min. 1 1 Max Unit ms ms V 10 1.9 9.8 PROGRAM/ERASE PERFORMANCE Parameter Sector Erase Time (4Kbyte) Block Erase Time (32Kbyte) Block Erase Time (64Kbyte) Chip Erase Time (128Mb) Page Programming Time Byte Program Unit Typ Max ms 45 300 s 0.15 0.75 s 0.3 1.5 s 30 90 ms 0.2 1.0 µs 8 40 Note: These parameters are characterized and are not 100% tested. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 69 IS25LP128 9.9 RELIABILITY CHARACTERISTICS Parameter Min Unit Test Method Endurance 100,000 Cycles JEDEC Standard A117 Data Retention 20 Years JEDEC Standard A103 ESD – Human Body Model 2,000 Volts JEDEC Standard A114 ESD – Machine Model 200 Volts JEDEC Standard A115 mA JEDEC Standard 78 Latch-Up 100 + ICC1 Note: These parameters are characterized and are not 100% tested. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 70 IS25LP128 10. PACKAGE TYPE INFORMATION 10.1 8-PIN JEDEC 208MIL BROAD SMALL OUTLINE INTEGRATED CIRCUIT (SOIC) PACKAGE (JB) (1) TOP VIEW SIDE VIEW 0.48 0.35 5.38 5.18 1.27 BSC 5.38 5.18 8.10 7.70 2.16 1.75 0.25 0.05 END VIEW 5.33 5.13 5.38 5.18 0.25 0.19 0.80 0.50 Note1. All dimensions are in millimeters. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 71 IS25LP128 10.2 8-CONTACT ULTRA-THIN SMALL OUTLINE NO-LEAD (WSON) PACKAGE 6X5MM (JK) (1) Top View Side View 5.00 BSC 0.25 0.19 6.00 BSC 0.80 0.70 Pin 1 Bottom View 4.00 1.27 BSC 3.40 0.48 0.35 0.75 0.50 Note1. All dimensions are in millimeters. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 72 IS25LP128 10.3 8-CONTACT ULTRA-THIN SMALL OUTLINE NO-LEAD (WSON) PACKAGE 8X6MM (JL) (1) . SYMBOL Note1. All dimensions are in millimeters. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 DIMENSION IN MM MIN. NOM MAX A 0.70 0.75 0.80 A1 0.00 0.02 0.05 A2 --- 0.20 --- D 7.90 8.00 8.10 E 5.90 6.00 6.10 D1 4.65 4.70 4.75 E1 4.55 4.60 4.65 e --- 1.27 --- b 0.35 0.40 0.48 L 0.4 0.50 0.60 73 IS25LP128 E E1 10.4 8-PIN 208MIL VSOP PACKAGE (JF) (1) θ L D 10°(4x) A2 A1 A c e b Symbols A Min - Typ - Max 1 A1 0.05 0.1 0.15 A2 0.75 0.8 0.85 b 0.35 0.42 0.48 c - .127 REF - D 5.18 5.28 5.38 E 7.7 7.9 8.1 E1 5.18 5.28 5.38 e - 1.27 - L 0.5 0.65 0.8 y - - 0.1 θ 0° - 8° Note1. All dimensions are in millimeters. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 74 IS25LP128 10.5 16-LEAD PLASTIC SMALL OUTLINE PACKAGE (300 MILS BODY WIDTH) (JM) (1) Millimeters 10.65 7.6 10.0 9 7.4 16 10.1 10.5 0.23 0.32 Detail A 1 8 2.25 2.4 2.35 2.65 Detail A 1.27 0.1 0.33 0.51 0.1 0.3 0.4 1.27 00 80 Note1. All dimensions are in millimeters. Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 75 IS25LP128 11. ORDERING INFORMATION Density Frequency (MHz) 128Mb 133 Order Part Number Package IS25LP128-JBLE 8-pin SOIC 208mil IS25LP128-JKLE 8-pin WSON (6x5 mm) IS25LP128-JLLE 8-pin WSON (6x8 mm) IS25LP128-JFLE 8-pin VSOP 208mil IS25LP128-JMLE 16-pin 300mil IS25LP128-JBLA* 8-pin SOIC 208mil (Call Factory) IS25LP128-JKLA* 8-pin WSON (6x5 mm) (Call Factory) IS25LP128-JLLA* 8-pin WSON (6x8 mm) (Call Factory) IS25LP128-JFLA* 8-pin VSOP 208mil (Call Factory) IS25LP128-JMLA* 16-pin 300mil (Call Factory) IS25LP128-JWLE KGD (Call Factory) A* = A1, A2, A3 Automotive Temperature Range E = A1= A2= A3= -40 to 105 C -40 to 85 C -40 to 105 C -40 to 125 C Integrated Silicon Solution, Inc.- www.issi.com Rev. A 5/03/2014 76