DS90LV027 LVDS Dual High Speed Differential Driver General Description Features The DS90LV027 is a dual LVDS driver device optimized for high data rate and low power applications. The DS90LV027 is a current mode driver allowing power dissipation to remain low even at high frequency. In addition, the short circuit fault current is also minimized. The device is in a 8-lead small Outline Package. The DS90LV027 has a flow-through design for easy PCB layout. The differential driver outputs provides low EMI with its low output swings typically 340 mV. Perfect for high speed transfer of clock and data. Pair with any of National’s LVDS receivers. n n n n n n n n Ultra Low Power Dissipation Operating Range above 155 Mbps Flow-through pinout simplifies PCB layout Conforms to TIA/EIA-644 Standard 8-Lead SOIC Package Saves Space VCM ± 1V center around 1.2V Low Differential Output Swing Typical 340 mV Power Off Protection (outputs in high impedance) Connection Diagram Dual-In-Line 10002901 Order Number DS90LV027M See NS Package Number M08A Functional Diagram 10002902 10002903 © 2005 National Semiconductor Corporation DS100029 www.national.com DS90LV027 LVDS Dual High Speed Differential Driver August 2005 DS90LV027 Absolute Maximum Ratings (Note 1) Lead Temperature Range If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Rating (Note 4) Supply Voltage (VCC) Soldering (4 sec.) +260˚C ≥ 4.5 kV (HBM 1.5 kΩ, 100 pF) −0.3V to +6V Input Voltage (DI) −0.3V to (VCC + 0.3V) Output Voltage (DO ± ) Recommended Operating Conditions −0.3V to +3.9V Maximum Package Power Dissipation @ +25˚C M Package 1190 mW Derate M Package Supply Voltage (VCC) 9.5 mW/˚C above +25˚C Storage Temperature Range Min Typ Max 3.0 3.3 3.6 V 0 25 70 ˚C Temperature (TA) −65˚C to +150˚C Units Electrical Characteristics Over Supply Voltage and Operating Temperature ranges, unless otherwise specified. (Notes 2, 3, 7) Symbol Parameter Conditions Pin Min Typ Max Units DO+, DO− 250 340 450 mV 0 10 35 mV 1.43 1.6 DIFFERENTIAL DRIVER CHARACTERISTICS VOD Output Differential Voltage ∆VOD VOD Magnitude Change VOH Output High Voltage VOL Output Low Voltage 0.9 1.09 VOS Offset Voltage 0.9 1.25 1.6 V ∆VOS Offset Magnitude Change 0 5 25 mV IOZD TRI-STATE ® Leakage VOUT = VCC or GND 0 Power-off Leakage VOUT = 3.6V or GND, VCC = 0V 0 ± 10 ± 10 µA IOXD ±1 ±1 IOSD Output Short Circuit Current −4 −6 mA VIH Input High Voltage VIL Input Low Voltage RL = 100Ω (Figure 1) DI IIH Input High Current VIN = 3.6V or 2.4V IIL Input Low Current VIN = GND or 0.5V VCL Input Clamp Voltage ICL = −18 mA ICC Power Supply Current No Load µA 2.0 VCC V GND 0.8 V ± 10 ± 10 µA ±1 ±1 −1.5 VIN = VCC or GND V V µA −0.8 VCC RL = 100Ω V 1 4 mA 8 11 mA Switching Characteristics Over Supply Voltage and Operating Temperature Ranges, unless otherwise specified. (Notes 5, 6) Symbol Parameter Conditions Min Typ Max Units DIFFERENTIAL DRIVER CHARACTERISTICS tPHLD Differential Propagation Delay High to Low tPLHD Differential Propagation Delay Low to High RL = 100Ω, CL = 5 pF (Figure 2 and Figure 3) 1.5 3.4 6 ns 1.5 3.5 6 ns tSKD Differential Skew |tPHLD − tPLHD| 0 0.1 1.9 ns tTLH Transition Low to High Time 0 1 3 ns tTHL Transition High to Low Time 0 1 3 ns Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation. Note 2: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except VOD. Note 3: All typicals are given for: VCC = +3.3V and TA = +25˚C. Note 4: ESD Rating: HBM (1.5 kΩ, 100 pF) ≥ 4.5 kV Note 5: CL includes probe and fixture capacitance. Note 6: Generator waveform for all tests unless otherwise specified: f = 1 MHz, ZO = 50Ω, tr ≤ 6 ns, tf ≤ 6 ns (10%-90%). Note 7: The DS90LV027 is a current mode device and only function with datasheet specification when a resistive load is applied to the drivers outputs. www.national.com 2 DS90LV027 Parameter Measurement Information 10002904 FIGURE 1. Differential Driver DC Test Circuit 10002905 FIGURE 2. Differential Driver Propagation Delay and Transition Time Test Circuit 10002906 FIGURE 3. Differential Driver Propagation Delay and Transition Time Waveforms Application Information TABLE 1. Device Pin Descriptions Truth Table Pin # Name 2, 3 DI DO− 6, 7 DO+ Non-inverting driver output pin H 5, 8 DO− Inverting driver output pin Input/Output DI DO+ L L H H L 4 DI > 0.8V and DI < 2.0V X X 1 H = Logic high level L = Logic low level X = indeterminant 3 GND VCC Description TTL/CMOS driver input pins Ground pin Positive power supply pin, +3.3V ± 0.3V www.national.com DS90LV027 LVDS Dual High Speed Differential Driver Physical Dimensions inches (millimeters) unless otherwise noted Order Number DS90LV027M NS Package Number M08A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560