HER1601G-HER1608G 16AMP. Glass Passivated High Efficient Rectifiers TO-220AB Features Glass passivated chip junction. High efficiency, Low VF High current capability High reliability High surge current capability For use in low voltage, high frequency inventor, free wheeling, and polarity protection application. Mechanical Data Cases: TO-220AB molded plastic Epoxy: UL 94V0 rate flame retardant Polarity: As marked High temperature soldering guaranteed: Dimensions in inches and (millimeters) 260oC/10 seconds .16”,(4.06mm) from case. Weight: 2.24 grams Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Symbol Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @TC =100 oC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @8.0A Maximum DC Reverse Current @TA=25 oC at Rated DC Blocking Voltage @ TA=125 oC Typical Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance (Note 3) Operating Temperature Range VRRM VRMS VDC HER HER HER HER HER HER HER HER 1601G 1602G 1603G 1604G 1605G 1606G 1607G 1608G 50 35 50 100 200 300 400 600 800 1000 70 140 210 280 420 560 700 100 200 300 400 600 800 1000 V V V I(AV) 16.0 A IFSM 125 A VF 1.0 1.3 IR Trr Cj RθJC TJ 1.7 10 400 50 80 80 50 1.5 -65 to +150 -65 to +150 Storage Temperature Range TSTG 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A Notes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0V D.C. 3. Mounted on Heatsink Size of 4 in x 6 in x 0.25 in Al-Plate. http://www.luguang.cn Units mail:[email protected] V uA uA nS pF o C/W o C o C HER1601G-HER1608G 16AMP. Glass Passivated High Efficient Rectifiers FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 1000 20 16 INSTANTANEOUS REVERSE CURRENT. ( A) 12 8 4 0 0 50 100 150 o FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG 0 Tj=25C 120 Tj=25 0C 1 0.1 20 40 60 80 100 120 140 0 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 8.3ms Single Half Sine Wave JEDEC Method 90 FIG.5- TYPICAL FORWARD CHARACTERISTICS PER LEG 60 100 30 200 Tj=25 0C 160 HE 120 R1 60 1G 80 HE ~H ER 16 R1 606 G~ 40 HE G 608 5 10 G 05 ER 16 3G G ~H 60 16 04 ER 1 G 08 16 ER 1.0 0.3 G ~H 0.1 0 0.01 0.4 G 2 3.0 0.03 05 R1 0 1 10 ER FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG 240 30 06 100 16 50 1G ~H 20 H 10 ER 5 H 2 60 1 R1 0 NUMBER OF CYCLES AT 60Hz CAPACITANCE.(pF) 10 150 INSTANTANEOUS FORWARD CURRENT. (A) PEAK FORWARD SURGE CURRENT. (A) CASE TEMPERATURE. ( C) Tj=125 0C 100 HE AVERAGE FORWARD CURRENT. (A) RATINGS AND CHARACTERISTIC CURVES (HER1601G THRU HER1608G) 20 50 100 200 500 1000 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE. (V) REVERSE VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms http://www.luguang.cn 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm mail:[email protected] 1.8