SF801G-SF808G 8.0AMP. Glass Passivated Super Fast Rectifiers TO-220AB Features High efficiency, low VF High current capability High reliability High surge current capability Low power loss. For use in low voltage, high frequency inventor, free wheeling, and polarity protection application Mechanical Data Case: TO-220AB Molded plastic Epoxy: UL 94V-0 rate flame retardant Polarity: As marked High temperature soldering guaranteed: Dimensions in inches and (millimeters) 260oC/10 seconds .16”,(4.06mm) from case. Weight: 2.24 grams Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Symbol Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375 (9.5mm) Lead Length @TC = 100 oC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 4.0A Maximum DC Reverse Current @TA=25 oC at Rated DC Blocking Voltage @ TA=100 oC Maximum Reverse Recovery Tim (Note 1) Typical Junction Capacitance (Note 2) Typical Thermal Resistance (Note 3) Operating Temperature Range TJ VRRM VRMS VDC SF SF SF SF SF SF SF SF 801G 802G 83G 804G 805G 806G 807G 808G 50 35 50 Units 100 150 200 300 400 500 600 70 105 140 210 280 350 480 100 150 200 300 400 500 600 I(AV) 8.0 A IFSM 125 A VF 0.975 RθJC TJ 1.7 10 400 35 IR Trr Cj 1.3 70 50 3.0 -65 to +150 -65 to +150 Storage Temperature Range TSTG TSTG 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A Notes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Thermal Resistance from Junction to Case Mounted on Heatsink Size of 2” x 3” x 0.25” Al-Plate. http://www.luguang.cn V V V mail:[email protected] V uA uA nS pF o C/W o C o C SF801G-SF808G 8.0AMP. Glass Passivated Super Fast Rectifiers FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- TYPICAL REVERSE CHARACTERISTICS 1000 8 6 4 2 0 0 50 100 150 o FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 10 TJ=25 0C 1 150 TJ=125 0C 120 0.1 8.3ms Single Half Sine Wave JEDEC Method 20 40 60 80 100 120 140 FIG.5- TYPICAL FORWARD CHARACTERISTICS 60 100 5 10 20 50 100 FIG.4- TYPICAL JUNCTION CAPACITANCE 100 Tj=25 0C 90 80 SF 80 SF 1G 80 ~S 5G F8 ~S 04 F8 G 08 G 70 60 50 2 5 10 10 3.0 1.0 0.3 0.1 0.03 40 1 30 SF 80 7G ~S F8 08 G 2 SF 80 1G ~S F8 04 5G G ~S F8 06 G 1 80 30 0 0 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 90 NUMBER OF CYCLES AT 60Hz CAPACITANCE.(pF) TJ=100 0C 100 SF PEAK FORWARD SURGE CURRENT. (A) CASE TEMPERATURE. ( C) INSTANTANEOUS REVERSE CURRENT. ( A) 10 INSTANTANEOUS FORWARD CURRENT. (A) AVERAGE FORWARD CURRENT. (A) RATINGS AND CHARACTERISTIC CURVES (SF801G THRU SF808G) 20 50 100 200 500 1000 Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE. (V) REVERSE VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms http://www.luguang.cn 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm mail:[email protected] 1.8