FR1001G-FR1007G Isolated 10AMP. Glass Passivated Fast Recovery Rectifiers TO-220AB Features Glass passivated chip junction. High efficiency, Low VF High current capability High reliability High surge current capability Low power loss Mechanical Data Cases: TO-220AB molded plastic Epoxy: UL 94V-0 rate flame retardant Terminals: Pure tin plated, Lead free. Polarity: As marked High temperature soldering guaranteed: 260 oC/10 seconds .16”,(4.06mm) from case. Mounting position: Any Weight: 2.24 grams Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current See Fig. 1 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 5.0A V RRM V RMS V DC FR FR FR FR FR FR FR 1001G 1002G 1003G 1004G 1005G 1006G 1007G 50 35 50 100 70 100 200 140 200 Maximum Reverse Recovery Time ( Note 1) Typical Junction Capacitance (Note 3) Typical Thermal Resistance RθJC (Note 2) 600 420 600 800 560 800 1000 700 1000 10 A IFSM 125 A VF 1.3 V IR 5.0 100 uA uA nS pF o C/W o C Trr Cj R θJC 150 250 40 3.0 -65 to +150 500 Operating and Storage Temperature Range T J ,T STG 1. Reverse Recovery Test Conditions: IF=0.5A, IR =1.0A, IRR =0.25A Notes: 2. Thermal Resistance from Junction to Case Per Leg Mounted on Heatsink Size 2” x 3” x 0.25” Al-Plate. 3. Measured at 1MHz and Applied Reverse Voltage of 4.0 Volts D.C. http://www.luguang.cn V V V I(AV) o Maximum DC Reverse Current @ T C =25 C at Rated DC Blocking Voltage @ T C =125 oC 400 280 400 Units mail:[email protected] FR1001G-FR1007G Isolated 10AMP. Glass Passivated Fast Recovery Rectifiers RATINGS AND CHARACTERISTIC CURVES (FR1001G THRU FR1007G) 1000 10 INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 12 8 6 4 2 0 50 100 150 o CASE TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 100 10 Tj=125 0C 1 PEAK FORWARD SURGE CURRENT. (A) 150 Tj=25 0C TJ=125 0C 125 0.1 8.3ms Single Half Sine Wave JEDEC Method 100 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 75 FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 50 80 25 40 0 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE 150 Tj=25 0C f=1.0MHz Vsig=50mVp-p CAPACITANCE.(pF) 20 INSTANTANEOUS FORWARD CURRENT. (A) 1 100 50 10 4 2 1 0.4 Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.2 0 0.1 0.5 1 5 10 50 100 0.1 0.8 500 1000 REVERSE VOLTAGE. (V) 0.9 1.0 1.1 1.2 1.3 FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE 1.4 INSTANTANEOUS FORWARD VOLTAGE. (V) OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms http://www.luguang.cn 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm mail:[email protected] 1.5