SFA1001G-SFA1008G 10.0AMP. Glass Passivated Super Fast Rectifiers TO-220AC .185(4.70) .175(4.44) .412(10.5) MAX .113(2.87) .103(2.62) Features .27(6.86) .23(5.84) .594(15.1) .587(14.9) High efficiency, low VF High current capability High reliability High surge current capability Low power loss. For use in low voltage, high frequency inventor, free wheeling, and polarity protection application PIN1 2 .16(4.06) .14(3.56) .11(2.79) .10(2.54) .56(14.22) .53(13.46) .037(0.94) .027(0.68) Mechanical Data .025(0.64) .014(0.35) .205(5.20) .195(4.95) PIN 1 Cases: TO-220AC Molded plastic Epoxy: UL 94V-0 rate flame retardant Polarity: As marked High temperature soldering guaranteed: 260oC/10 seconds/.16”,(4.06mm) from case Weight: 2.24 grams .055(1.40) .045(1.14) DIA .154(3.91) .148(3.74) PIN 2 CASE Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol SFA SFA SFA SFA Type Number SFA SFA SFA SFA 1001G 1002G 1003G 1004G 1005G 1006G 1007G 1008G Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage VRRM VRMS VDC 50 35 50 100 70 100 150 105 150 200 140 200 300 210 300 400 280 400 Maximum Average Forward Rectified 10 I(AV) Current @TC = 100 oC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated 125 IFSM Load (JEDEC method ) Maximum Instantaneous Forward Voltage 0.975 1.3 VF @ 10.0A Maximum DC Reverse Current @ TA=25 oC at Rated DC Blocking Voltage 10 IR @ TA=125 oC 400 Maximum Reverse Recovery Time Trr 35 (Note 1) Typical Junction Capacitance (Note 2) Cj 70 Typical Thermal resistance (Note 3) 3.5 RθJC Operating Temperature Range TJ -65 to +150 Storage Temperature Range TSTG -65 to +150 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A Notes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Mounted on Heatsink Size of 2” x 3” x 0.25”Al-Plate. http://www.luguang.cn 500 350 500 Units 600 420 600 V V V A A 1.7 V uA uA nS 50 mail:[email protected] o pF C/W o C o C SFA1001G-SFA1008G 10.0AMP. Glass Passivated Super Fast Rectifiers RATINGS AND CHARACTERISTIC CURVES (SFA1001G THRU SFA1008G) FIG.2- TYPICAL REVERSE CHARACTERISTICS 1000 6 4 2 0 0 50 100 150 o PEAK FORWARD SURGE CURRENT. (A) CASE TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG TC=100 0C 100 10 TC=25 0C 1.0 TC=125 0C 120 0.1 8.3ms Single Half Sine Wave JEDEC Method 0 20 40 60 80 100 120 140 90 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 60 FIG.5- TYPICAL FORWARD CHARACTERISTICS PER LEG 100 30 4G 6G 00 A1 SF ~ 5G 00 A1 8G SF 00 A1 SF ~ 7G 00 A1 SF 00 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG 100 Tj=25 0C 90 80 G 04 10 FA ~S G 1G 08 00 10 A1 FA SF ~S 5G 00 A1 SF CAPACITANCE.(pF) INSTANTANEOUS REVERSE CURRENT. ( A) 8 70 60 50 1 2 5 10 20 INSTANTANEOUS FORWARD CURRENT. (A) AVERAGE FORWARD CURRENT. (A) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 10 1 FA 30 S G~ 1 00 A1 SF 10 3.0 1.0 0.3 0.1 .03 Tj=25oC Pulse Width=300 s 1% Duty Cycle .01 .4 50 100 200 500 .6 .8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE. (V) REVERSE VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms http://www.luguang.cn 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm mail:[email protected] 1.8