SE-1000 1000W Single Output Power Supply series Features : AC input active surge current limiting AC input range selected by switch Protections: Short circuit / Overload / Over voltage / Over temperature Forced air cooling by built-in DC ball bearing fan High power density 7.3w/inch3 With DC_OK signal output Built-in remote ON-OFF control Built-in remote sense function UL / CUL approved Low cost 2 years warranty SPECIFICATION MODEL OUTPUT SE-1000-5 SE-1000-9 SE-1000-12 SE-1000-15 SE-1000-24 SE-1000-48 DC VOLTAGE 5V 9V 12V 15V 24V 48V RATED CURRENT 150A 100A 83.3A 66.7A 41.7A 20.8A CURRENT RANGE 0 ~ 150A 0 ~ 100A 0 ~ 83.3A 0 ~ 66.7A 0 ~ 41.7A 0 ~ 20.8A RATED POWER 750W 900W 999.6W 1000.5W 1000.8W 998.4W RIPPLE & NOISE (max.) Note.2 150mVp-p 150mVp-p 150mVp-p 150mVp-p 200mVp-p 200mVp-p VOLTAGE ADJ. RANGE 7.5 ~ 10V 10 ~ 13.5V 13.5 ~ 16.5V 22 ~ 27.5V 43 ~ 56V VOLTAGE TOLERANCE Note.3 INPUT 1.0% 1.0% 1.0% 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION 1.0% 0.5% 0.5% 0.5% 0.5% 0.5% SETUP, RISE TIME 1500ms, 50ms/230VAC HOLD UP TIME (Typ.) 20ms/230VAC VOLTAGE RANGE 90 ~ 132VAC / 180 ~ 264VAC selected by TB2 FREQUENCY RANGE 47 ~ 63Hz 1500ms, 50ms/115VAC at full load 15ms/115VAC at full load 254 ~ 370VDC 85% 84% EFFICIENCY (Typ.) 81% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 17.5A/115VAC 35A/115VAC LEAKAGE CURRENT <2.5mA / 240VAC OVERLOAD 105 ~ 125% rated output power Protection type : Shut down o/p voltage, re-power on to recover DC_OK SIGNAL 5.75 ~ 6.3V 10.4 ~ 12.2V 13.8 ~ 16.2V 20 ~ 90% RH non-condensing PACKING 89% 18 ~ 21V 28 ~ 32.4V 57.6 ~ 67.2V Protection type : Shut down o/p voltage, recovers automatically after temperature goes down PSU turn on:3.3V ~ 5.6V PUS turn off:0 ~ 1V WORKING HUMIDITY DIMENSION 88% Protection type : Shut down o/p voltage, re-power on to recover 70 5 (TSW1) detect on heatsink of power transistor WORKING TEMP. ISOLATION RESISTANCE MTBF 86% 10A/230VAC 55A/230VAC RC+/RC-: 0 ~ 0.8V power on; 4 ~ 10V power off -20 ~ +60 (Refer to "Derating Curve") REMOTE CONTROL ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE SAFETY NOTE 1.0% 0.5% OVER TEMPERATURE OTHERS 1.0% LINE REGULATION PROTECTION OVER VOLTAGE FUNCTION 3.3 ~ 5.5V 1.0% -40 ~ +85 , 10 ~ 95% RH 0.05%/ (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1 approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 251.6K hrs min. MIL-HDBK-217F (25 278*127*63.5mm (L*W*H) 2.5Kg; 6pcs/16Kg/1.38CUFT / 70% RH ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. By using UVP circuit, PSU will not turn on direct by in AC continue ON/OFF condition within 5 sec. File Name:SE-1000-SPEC 2011-08-23 SE-1000 1000W Single Output Power Supply Mechanical Specification Case No. 935B series Unit:mm 278 19 max. 19 63.5 38 12.5 171.5 16 39 max. 8-M4(Both Sides) 171.5 12.25 19 LED 4-M4 Air flow direction 127 101.5 +V ADJ CN3 1 + -V 1 2 6 9.25 11 1 2 3 OUTPUT TB1 TB2 TB1:AC input terminal Pin No. 1 2 3 TB2:110/220V Change Pin No. 1 2 Assignment AC/L AC/N FG Control Pin (CN3) : JST B6B-XH or equivalent 110V 220V Short Open Pin No. 1 2 3 Assignment DC_OK Signal DC_OK GND -S Pin No. 4 5 6 Assignment +S RCRC+ Mating Housing Terminal JST XHP or equivalent JST SXH-001T or equivalent Block Diagram fosc : 55KHz 110/220V(TB2) ACTIVE INRUSH CURRENT LIMITING EMI FILTER I/P (TB1) RECTIFIERS +S RECTIFIERS & FILTER POWER SWITCHING +V -V -S O.V.P. O.L.P. O.T.P. PWM CONTROL DETECTION CIRCUIT FAN LOCK PROTECTION AUX POWER Derating Curve DC_OK REMOTE CONTROL RC FAN Static Characteristics 100 100 Others 90 80 5V,12V 70 LOAD (%) LOAD (%) 60 50 40 20 -20 180 ~ 264VAC 90 ~ 132VAC 80 60 50 40 0 10 20 30 40 45 50 AMBIENT TEMPERATURE ( ) 60 70 (HORIZONTAL) 90 180 95 190 100 200 115 230 132 264 INPUT VOLTAGE (VAC) 60Hz File Name:SE-1000-SPEC 2011-08-23 SE-1000 1000W Single Output Power Supply series Mechanical Specification DC_OK Signal DC_OK Signal is the voltage difference between "DC_OK" and "G" pin output DC_OK Signal is a TTL level signal PSU turn on: 3.3 ~ 5.6V PSU turn off: 0 ~ 1V +V CN3 RC+ RC- +S -S G ADJ DC OK -V + G DC_OK LOAD + - Remote Sensing +V CN3 RC+ RC- +S -S ADJ DC G OK -V + -S LOAD - +S + Remote Control Between RC+ and RC- Output SW OFF(0 ~ 0.8V) ON SW ON(4 ~ 10V) OFF +V CN3 RC+ RC- +S -S G ADJ DC OK + SW External Power Source -V RC+ I=6~20mA RCConnector for remote Control LOAD + File Name:SE-1000-SPEC 2011-08-23