WRD-YKD-5W Series 24 DC-DC CONVERTER 5W, WIDE INPUT ISOLATED & REGULATED TWIN OUTPUT DIP DIP24 PRODUCT PROGRAM Input Part Output Efficiency Nomina Range Max* No-load Current (mA,Typ) WRD120505YKD-5W l 12 9.0-18 22 25 5/5 500/500 50/50 76 FEATURES WRD120909YKD-5W 12 9.0-18 22 25 9/9 278/278 28/28 78 WRD121212YKD-5W 12 9.0-18 22 25 12/12 208/208 21/21 80 ◆2:1 wide input voltage range WRD121515YKD-5W 12 9.0-18 22 25 15/15 167/167 17/17 81 WRD122424YKD-5W 12 9.0-18 22 25 24/24 104/104 10/10 82 WRD240505YKD-5W 24 18-36 40 15 5/5 500/500 50/50 76 WRD240512YKD-5W 24 18-36 40 15 5/12 500/208 50/21 77 WRD241212YKD-5W 24 18-36 40 15 12/12 208/208 21/21 80 WRD241515YKD-5W 24 18-36 40 15 15/15 167/167 17/17 79 ◆No external component required WRD242405YKD-5W 24 18-36 40 15 24/05 104/500 10/50 81 WRD242424YKD-5W 24 18-36 40 15 24/24 104/104 10/10 81 ◆Industry standard pin out WRD480505YKD-5W 48 36-72 80 10 5/5 500/500 50/50 76 WRD480512YKD-5W 48 36-72 80 10 5/12 500/208 50/21 78 WRD480909YKD-5W 48 36-72 80 10 9/9 278/278 28/28 78 WRD481212YKD-5W 48 36-72 80 10 12/12 208/208 21/21 80 WRD481515YKD-5W 48 36-72 80 10 15/15 167/167 17/17 81 ◆ MTBF>1,000,000 hours WRD482424YKD-5W 48 36-72 80 10 24/24 104/104 10/10 82 ◆ No heat sink required *Input voltage can't exceed this value, or will cause the permanent damage. Number ◆Twin output ◆Operating temperature: -40℃ to + 85℃ ◆UL94-V0 package ◆Short circuit protection(automatic recovery) ◆ Five-sided metal shielding Voltage(VDC) Voltage Current(MA) (VDC) Max Min. (%,Typ) ◆ RoHS Compliance MODEL SELECTION WR D①12②05③05④Y⑤ KD⑥-5W⑦ WRD ①Product Series ③1st Output Voltage ⑤Wide (2:1) Input Range ⑦Rated Power ②Input Voltage ④2nd Output Voltage ⑥Package Style APPLICATIONS The WRD_YKD-5W series are specially designed for applications where a wide range input voltage power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1)Where the voltage of the input power supply is wide range (voltage range≤2:1); 2)Where isolation is necessary between input and output (Isolation Voltage≤1500VDC); 3)Where isolation is necessary between Vout1 and Vout2 (Isolation Voltage≤1000VDC); 4)Where the regulation of the output voltage and the output ripple noise are demanded. COMMON SPECIFICATIONS Item Test Conditions Min. Storage humidity Max. Units 95 % Operating temperature -40 85 Storage Temperature -55 125 Temp. rise at full load PRODUCT ID DESCRIPTION Typ. Lead temperature Cooling Case Material Short circuit protection MTBF 1.5mm from case for 10 seconds 300 Free Air Convection Plastic (UL94-V0) Continuous, Automatic Recovery 1000 Weight K hours 15 MICRODC R ESERVES THE COPYRIGHT http://www.microdc.cn ℃ 15 Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 1 of 3 g WRD-YKD-5W Series TYPICAL CHARACTERISTICS ISOLATION SPECIFICATIONS Item Test Conditions Min. Typ. Isolation voltage Tested for 1 minute and 1mA max 1500 Isolation resistance Test at 500VDC 1000 Isolation capacitance Input/Output, 100KHz/1V Max. Units VDC MΩ 100 pF *Supply voltage must be discontinued at the end of short circuit duration. OUTPUT SPECIFICATIONS Item Test Conditions Min. 0.5 Typ. Max. Units 5 W ±1 ±3 Output power Refer to product program Main output voltage accuracy Refer to recommended circuit Vice-output voltage accuracy Refer to recommended circuit ±3 ±5 Load regulation From 10% to 100% load ±0.5 ±1* ±0.2 % ±0.5 Line regulation Input voltage from low to high Temperature drift (Vout) Refer to recommended circuit Ripple** 20MHz Bandwidth 20 50 Noise** 20MHz Bandwidth 75 150 Switching frequency 100% load, input voltage range 300 ±0.03 %/℃ mVp-p RECOMMENDED CIRCUIT KHz *Dual output models unbalanced load: ±5%. **Test ripple and noise by “parallel cable”method. See detailed operation instructions at Testing of Power Converter section, application notes. APPLICATION NOTE 1) Requirement On Output Load In full order to ensure load), a minimum input voltage less than reliability the load product is is not exceeded, will reduce for efficiently this kind the minimum output the specified minimum resistor as extra operate specified greatly. load, If the the load no output actual and reliably, in addition to a max load (namely of DC/DC converter. Make sure the specified less than 10% ripple may increase output power is very load. sharply small, If while please the its add range actual load efficiency an of is and appropriate loading, or contact our company for other lower output power products. 2) Recommended Circuit All the WRD-YKD-5W Series have been tested according to the following recommended testing circuit before leaving factory. This series should be tested under load (see Figure 1). If you want to further choose capacitors with start-up problem. If low decrease the input/output ESR. However, you want to use the the ripple, capacitance products in you can should high increase not EMI, be capacitance too high, properly or may or cause please choose our metal packaged products. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1). General: Cin: 5V,12V 100µF 24V&48V 22µF/10µF EXTERNAL CAPACITOR TABLE (TABLE 1) Cout: 10µF/100mA Output External Capacitor Table (Table 1) 3) Input Current While using unstable power source, please ensure the output voltage and ripple voltage do not exceed indexes of the converter. The preceding power source must be able to provide for converter sufficient starting current Ip (Figure 2). General: Ip≤1.4*Iin-max Vout(VDC) Cout(uF) 5 680 9 470 12 330 15 220 24 100 4) No parallel connection or plug and play http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 2 of 3 WRD-YKD-5W Series OUTLINE DIMENSIONS ＆ FOOTPRINT DETAILS MECHANICAL DIMENSIONS RECOMMENDED FOOTPRINT(TOP VIEW) TUBE OUTLINE DIMENSIONS RoHS COMPLIANT INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are backward compatible with Sn/Pb soldering systems. Microdc Professional Power Module,Inc. Tel:0086-20-86000646 REACH COMPLIANT INFORMATION E-mail:[email protected] Website: www.microdc.cn http://www.microdc.cn This series has proven that this product does not contain harmful chemicals, it also has harmful chemical substances through the registration, inspection and approval. Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 3 of 3