MP4458 1A, 4MHz, 36V Step-Down Converter The Future of Analog IC Technology FEATURES DESCRIPTION The MP4458 is a high frequency step-down switching regulator with an integrated internal high-side high voltage power MOSFET. It provides 1 A output with current mode control for fast loop response and easy compensation. The wide 3.8V to 36V input range accommodates a variety of step-down applications, including those in automotive systems. A 120µA operational quiescent current is suitable for use in battery-powered applications. The frequency foldback helps prevent inductor current runaway during startup and thermal shutdown provides reliable, fault tolerant operation. In some applications, such as AM radio and ADSL applications, in which the device is sensitive to frequency band, the MP4458 can avoid the related EMI problem by setting the frequency at 4MHz. The MP4458 is available in thin 10-pin 3mm x 3mm TQFN package. • • • • • • • • • • 120μA Quiescent Current Wide 3.8V to 36V Operating Input Range 300mΩ Internal Power MOSFET Up to 4MHz Programmable Switching Frequency Ceramic Capacitor Stable Internal Soft-Start Precision Current Limit without a Current Sensing Resistor Up to 95% Efficiency Output Adjustable from 0.8V to 30V Available in 10-Pin 3x3mm TQFN Package APPLICATIONS • • • • • High Voltage Power Conversion Automotive Systems Industrial Power Systems Distributed Power Systems Battery Powered Systems All MPS parts are lead-free and adhere to the RoHS directive. For MPS green status, please visit MPS website under Products, Quality Assurance page. “MPS” and “The Future of Analog IC Technology” are registered trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION Efficiency vs Load Current 100 VI=5V 4 CONTROL C6 NS 3 7 5 COMP EN VIN BST MP4458 FREQ FB SW GND 8, 9 VIN 36V max 10 1, 2 6 C4 100nF 10MQ100N VOUT 5V @ 1A EFFICIENCY (%) 90 80 VI=12V 70 60 50 40 VO=3.3V 30 20 MP4458 Rev. 1.02 3/4/2013 VI=24V 0 500 LOAD CURRENT (mA) www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 1000 1 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER ORDERING INFORMATION Part Number* Package Top Marking MP4458DQT 3x3mm TQFN10 T2 * For Tape & Reel, add suffix –Z (e.g. MP4458DQT–Z); For RoHS, compliant packaging, add suffix –LF (e.g. MP4458DQT–LF–Z). PACKAGE REFERENCE TOP VIEW SW 1 10 BST SW 2 9 VIN EN 3 8 VIN COMP 4 7 FREQ FB 5 6 GND EXPOSED PAD ON BACKSIDE ABSOLUTE MAXIMUM RATINGS (1) Thermal Resistance Supply Voltage (VIN).....................–0.3V to +40V Switch Voltage (VSW)............ –0.3V to VIN + 0.3V BST to SW .....................................–0.3V to +6V All Other Pins .................................–0.3V to +6V Junction Temperature ...............................150°C (2) Continuous Power Dissipation (TA = +25°C) 3x3 TQFN10 .............................................. 2.5W Lead Temperature ....................................260°C Storage Temperature.............. –65°C to +150°C 3x3 TQFN10 ........................... 50 ...... 12... °C/W Recommended Operating Conditions (3) Supply Voltage VIN ...........................3.8V to 36V Output Voltage VOUT .........................0.8V to 30V Operating Junct. Temp. .......... –40°C to +125°C MP4458 Rev. 1.02 3/4/2013 (4) θJA θJC Notes: 1) Exceeding these ratings may damage the device. 2) The maximum allowable power dissipation is a function of the maximum junction temperature TJ (MAX), the junction-toambient thermal resistance θJA, and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD (MAX) = (TJ (MAX)-TA)/θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3) The device is not guaranteed to function outside of its operating conditions. 4) Measured on JESD51-7 4-layer board. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 2 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER ELECTRICAL CHARACTERISTICS VIN = 12V, VEN = 2.5V, VCOMP = 1.4V, TA = +25°C, unless otherwise noted. Parameter Symbol Condition Feedback Voltage Upper Switch On Resistance Upper Switch Leakage Current Limit COMP to Current Sense Transconductance Error Amp Voltage Gain (5) Error Amp Transconductance Error Amp Min Source current Error Amp Min Sink current VIN UVLO Threshold VIN UVLO Hysteresis Soft-Start Time (5) VFB RDS(ON) 4.5V < VIN < 36V VBST – VSW = 5V VEN = 0V, VSW = 0V, VIN = 36V Duty Cycle = 50% Min Typ Max Units 0.776 0.8 300 1 1.8 0.824 V mΩ μA A 1.4 GCS ICOMP = ±3µA VFB = 0.7V VFB = 0.9V 40 2.7 Oscillator Frequency fS Shutdown Supply Current Quiescent Supply Current IQ 0V < VFB < 0.8V RFREQ = 45kΩ RFREQ = 18kΩ VEN = 0V No load, VFB = 0.9V 1.6 3.2 2.2 3.1 A/V 200 60 5 –5 3.0 0.35 1.5 2 4 12 120 V/V µA/V µA µA V V ms MHz MHz µA µA 80 3.3 2.4 4.8 18 145 Thermal Shutdown 150 °C Thermal Shutdown Hysteresis 15 Minimum Off Time Minimum On Time (5) EN Up Threshold EN Down Threshold 100 100 1.5 1.2 °C ns ns V V 1.35 1.15 1.65 1.25 5) Guaranteed by design. MP4458 Rev. 1.02 3/4/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 3 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER PIN FUNCTIONS Pin # 1, 2 3 4 5 6 7 8, 9 10 Name Description Switch Node. This is the output from the high-side switch. A low Vf Schottky rectifier to SW ground is required. The rectifier must be close to the SW pins to reduce switching spikes. Enable Input. Pulling this pin below the specified threshold shuts the chip down. Pulling it up EN above the specified threshold or leaving it floating enables the chip. Compensation. This node is the output of the GM error amplifier. Control loop frequency COMP compensation is applied to this pin. Feedback. This is the input to the error amplifier. An external resistive divider connected FB between the output and GND is compared to the internal +0.8V reference to set the regulation voltage. GND, Ground. It should be connected as close as possible to the output capacitor avoiding the high Exposed current switch paths. The exposed pad and GND pin must be connected to the same ground Pad plane. Switching Frequency Program Input. Connect a resistor from this pin to ground to set the FREQ switching frequency. Input Supply. This supplies power to all the internal control circuitry, both BS regulators and VIN the high-side switch. A decoupling capacitor to ground must be placed close to this pin to minimize switching spikes. Bootstrap. This is the positive power supply for the internal floating high-side MOSFET driver. BST Connect a bypass capacitor between this pin and SW pin. MP4458 Rev. 1.02 3/4/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 4 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER TYPICAL PERFORMANCE CURVES VIN = 12V, VOUT = 5V, fS = 500KHz, TA = +25°C, unless otherwise noted. MP4458 Rev. 1.02 3/4/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 5 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER BLOCK DIAGRAM VIN VIN EN REFERENCE UVLO/ THERMAL SHUTDOWN 5V + -2.6V INTERNAL REGULATORS + -BST SW 1.5ms SS VOUT SS -- ISW + ISW Level Shift FB SW Gm Error Amp SS 0V8 -- COMP + OSCILLATOR CLK VOUT COMP GND FREQ Figure 1—Functional Block Diagram MP4458 Rev. 1.02 3/4/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 6 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER OPERATION The MP4458 is a variable frequency, non-synchronous, step-down switching regulator with an integrated high-side high voltage power MOSFET. It provides a single highly efficient solution with current mode control for fast loop response and easy compensation. It features a wide input voltage range, internal soft-start control and precision current limiting. Its very low operational quiescent current makes it suitable for battery powered applications. PWM Control At moderate to high output current, the MP4458 operates in a fixed frequency, peak current control mode to regulate the output voltage. A PWM cycle is initiated by the internal clock. The power MOSFET is turned on and remains on until its current reaches the value set by the COMP voltage. When the power switch is off, it remains off for at least 100ns before the next cycle starts. If, in one PWM period, the current in the power MOSFET does not reach the COMP set current value, the power MOSFET remains on, saving a turn-off operation. Error Amplifier The error amplifier compares the FB pin voltage with the internal reference (REF) and outputs a current proportional to the difference between the two. This output current is then used to charge the external compensation network to form the COMP voltage, which is used to control the power MOSFET current. During operation, the minimum COMP voltage is clamped to 0.9V and its maximum is clamped to 2.0V. COMP is internally pulled down to GND in shutdown mode. COMP should not be pulled up beyond 2.6V. Internal Regulator Most of the internal circuitries are powered from the 2.6V internal regulator. This regulator takes the VIN input and operates in the full VIN range. When VIN is greater than 3.0V, the output of the regulator is in full regulation. When VIN is lower than 3.0V, the output decreases. Enable Control The MP4458 has a dedicated enable control pin (EN). With high enough input voltage, the chip can be enabled and disabled by EN which has MP4458 Rev. 1.02 3/4/2013 positive logic. Its falling threshold is a precision 1.2V, and its rising threshold is 1.5V (300mV higher). When floating, EN is pulled up to about 3.0V by an internal 1µA current source so it is enabled. To pull it down, 1µA current capability is needed. When EN is pulled down below 1.2V, the chip is put into the lowest shutdown current mode. When EN is higher than zero but lower than its rising threshold, the chip is still in shutdown mode but the shutdown current increases slightly. Under-Voltage Lockout (UVLO) Under-voltage lockout (UVLO) is implemented to protect the chip from operating at insufficient supply voltage. The UVLO rising threshold is about 3.0V while its falling threshold is a consistent 2.6V. Internal Soft-Start The soft-start is implemented to prevent the converter output voltage from overshooting during startup. When the chip starts, the internal circuitry generates a soft-start voltage (SS) ramping up from 0V to 2.6V. When it is lower than the internal reference (REF), SS overrides REF so the error amplifier uses SS as the reference. When SS is higher than REF, REF regains control. Thermal Shutdown Thermal shutdown is implemented to prevent the chip from operating at exceedingly high temperatures. When the silicon die temperature is higher than its upper threshold, it shuts down the whole chip. When the temperature is lower than its lower threshold, the chip is enabled again. Floating Driver and Bootstrap Charging The floating power MOSFET driver is powered by an external bootstrap capacitor. This floating driver has its own UVLO protection. This UVLO’s rising threshold is 2.2V with a threshold of 150mV. The bootstrap capacitor is charged and regulated to about 5V by the dedicated internal bootstrap regulator. When the voltage between the BST and SW nodes is lower than its regulation, a PMOS pass transistor connected from VIN to BST is turned on. The charging current path is www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 7 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER from VIN, BST and then to SW. External circuit should provide enough voltage headroom to facilitate the charging. As long as VIN is sufficiently higher than SW, the bootstrap capacitor can be charged. When the power MOSFET is ON, VIN is about equal to SW so the bootstrap capacitor cannot be charged. When the external diode is on, the difference between VIN and SW is largest, thus making it the best period to charge. When there is no current in the inductor, SW equals the output voltage VOUT so the difference between VIN and VOUT can be used to charge the bootstrap capacitor. At higher duty cycle operation condition, the time period available to the bootstrap charging is less so the bootstrap capacitor may not be sufficiently charged. In case the internal circuit does not have sufficient voltage and the bootstrap capacitor is not charged, extra external circuitry can be used to ensure the bootstrap voltage is in the normal operational region. Refer to External Bootstrap Diode in Application section. Startup and Shutdown If both VIN and EN are higher than their appropriate thresholds, the chip starts. The reference block starts first, generating stable reference voltage and currents, and then the internal regulator is enabled. The regulator provides stable supply for the remaining circuitries. While the internal supply rail is up, an internal timer holds the power MOSFET OFF for about 50µs to blank the startup glitches. When the internal soft-start block is enabled, it first holds its SS output low to ensure the remaining circuitries are ready and then slowly ramps up. Three events can shut down the chip: EN low, VIN low and thermal shutdown. In the shutdown procedure, power MOSFET is turned off first to avoid any fault triggering. The COMP voltage and the internal supply rail are then pulled down. Programmable Oscillator The MP4458 oscillating frequency is set by an external resistor, RFREQ from the FREQ pin to ground. The relationship between RFREQ and fS refer to table1 in Application section. The DC quiescent current of the floating driver is about 20µA. Make sure the bleeding current at the SW node is higher than this value, such that: IO + VO > 20μA (R1 + R2) Current Comparator and Current Limit The power MOSFET current is accurately sensed via a current sense MOSFET. It is then fed to the high speed current comparator for the current mode control purpose. The current comparator takes this sensed current as one of its inputs. When the power MOSFET is turned on, the comparator is first blanked till the end of the turnon transition to avoid noise issues. The comparator then compares the power switch current with the COMP voltage. When the sensed current is higher than the COMP voltage, the comparator output is low, turning off the power MOSFET. The cycle-by-cycle maximum current of the internal power MOSFET is internally limited. MP4458 Rev. 1.02 3/4/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 8 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER APPLICATION INFORMATION Setting the Frequency The MP4458 has an externally adjustable frequency. The switching frequency (fS) can be set using a resistor at FREQ pin (RFREQ). The recommended RFREQ value for various fS, see Table1. Table 1—fS vs. RFREQ RFREQ (kΩ) fS (MHz) 18 4 20 3.8 22.1 3.5 24 3.3 26.7 3 30 2.8 33.2 2.5 39 2.2 45.3 2 51 1.8 57.6 1.6 68 1.4 80.6 1.2 100 1 133 0.8 200 0.5 340 0.3 536 0.2 Setting the Output Voltage The output voltage is set using a resistive voltage divider from the output voltage to FB pin. The voltage divider divides the output voltage down to the feedback voltage by the ratio: VFB = VOUT R2 R1 + R2 Where VFB is the feedback voltage and VOUT is the output voltage. small amount of current, keep R2 under 40kΩ. A typical value for R2 can be 40.2kΩ. With this value, R1 can be determined by: R1 = 50.25 × ( VOUT − 0.8)(kΩ) For example, for a 3.3V output voltage, R2 is 40.2kΩ, and R1 is 127kΩ. Inductor The inductor is required to supply constant current to the output load while being driven by the switched input voltage. A larger value inductor will result in less ripple current that will result in lower output ripple voltage. However, the larger value inductor will have a larger physical size, higher series resistance, and/or lower saturation current. A good rule for determining the inductance to use is to allow the peak-to-peak ripple current in the inductor to be approximately 30% of the maximum switch current limit. Also, make sure that the peak inductor current is below the maximum switch current limit. The inductance value can be calculated by: L1 = ⎛ ⎞ VOUT V × ⎜⎜1 − OUT ⎟⎟ fS × ΔIL ⎝ VIN ⎠ Where VIN is the input voltage, fS is the switching frequency, and ΔIL is the peak-to-peak inductor ripple current. Choose an inductor that will not saturate under the maximum inductor peak current. The peak inductor current can be calculated by: ILP = ILOAD + ⎛ ⎞ VOUT V × ⎜⎜1 − OUT ⎟⎟ 2 × fS × L1 ⎝ VIN ⎠ Where ILOAD is the load current. Table 2 lists a number of suitable inductors from various manufacturers. The choice of which style inductor to use mainly depends on the price vs. size requirements and any EMI requirement. Thus the output voltage is: VOUT = VFB (R1 + R2) R2 A few µA of current from the high-side BS circuitry can be seen at the output when the MP4458 is at no load. In order to absorb this MP4458 Rev. 1.02 3/4/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 9 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER Table 2—Selected Inductors Manufacturer Part Number Inductance (µH) Max DCR (Ω) Current Rating (A) Dimensions L x W x H (mm3) Wurth Electronics Wurth Electronics Wurth Electronics Wurth Electronics Wurth Electronics Wurth Electronics 7447789002 7447789003 7447789004 744066100 744771115 744771122 2.2µH 3.3µH 4.7µH 10µH 15µH 22µH 0.019 0.024 0.033 0.035 0.025 0.031 4A 3.42A 2.9A 3.6A 3.75 3.37 7.3x7.3x3.2 7.3x7.3x3.2 7.3x7.3x3.2 10x10x3.8 12x12x6 12x12x6 TDK RLF7030T-2R2 2.2µH 0.012 5.4A 7.3x6.8x3.2 TDK TDK TDK TDK RLF7030T-3R3 RLF7030T-4R7 SLF10145T-100 SLF12565T-150M4R2 3.3µH 4.7µH 10µH 15µH 0.02 0.031 0.0364 0.0237 4.1A 3.4A 3A 4.2 7.3x6.8x3.2 7.3x6.8x3.2 10.1x10.1x4.5 12.5x12.5x6.5 TDK SLF12565T-220M3R5 22µH 0.0316 3.5 12.5x12.5x6.5 TOKO TOKO TOKO TOKO TOKO TOKO FDV0630-2R2M FDV0630-3R3M FDV0630-4R7M #919AS-100M #919AS-160M #919AS-220M 2.2µH 3.3µH 4.7µH 10µH 16µH 22µH 0.021 0.031 0.049 0.0265 0.0492 0.0776 5.3 4.3 3.3 4.3 3.3 3.0 7.7x7x3 7.7x7x3 7.7x7x3 10.3x10.3x4.5 10.3x10.3x4.5 10.3x10.3x4.5 MP4458 Rev. 1.02 3/4/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 10 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER Output Rectifier Diode The output rectifier diode supplies the current to the inductor when the high-side switch is off. To reduce losses due to the diode forward voltage and recovery times, use a Schottky diode. Choose a diode whose maximum reverse voltage rating is greater than the maximum input voltage, and whose current rating is greater than the maximum load current. Table 3 lists example Schottky diodes and manufacturers. Table 3—Output Diodes For simplification, choose the input capacitor whose RMS current rating greater than half of the maximum load current. The input capacitor can be electrolytic, tantalum or ceramic. When using electrolytic or tantalum capacitors, a small, high quality ceramic capacitor, i.e. 0.1μF, should be placed as close to the IC as possible. When using ceramic capacitors, make sure that they have enough capacitance to provide sufficient charge to prevent excessive voltage ripple at input. The input voltage ripple caused by capacitance can be estimated by: Voltage Current Rating Rating Package (V) (A) ΔVIN = ⎛ ILOAD V V × OUT × ⎜⎜1 − OUT fS × C1 VIN ⎝ VIN ⎞ ⎟⎟ ⎠ Manufacturer Part Number Diodes Inc. B240A-13-F 40V 2A SMA Where CIN is the input capacitance value. Output Capacitor Diodes Inc. B340A-13-F 40V 3A SMA Central semi CMSH2-40M 40V 2A SMA Central semi CMSH3-40MA 40V 3A SMA Input Capacitor The input current to the step-down converter is discontinuous, therefore a capacitor is required to supply the AC current to the step-down converter while maintaining the DC input voltage. Use low ESR capacitors for the best performance. Ceramic capacitors are preferred, but tantalum or low-ESR electrolytic capacitors may also suffice. Since the input capacitor absorbs the input switching current it requires an adequate ripple current rating. The RMS current in the input capacitor can be estimated by: I C1 = ILOAD × VOUT ⎛⎜ VOUT × 1− VIN ⎜⎝ VIN ⎞ ⎟ ⎟ ⎠ The worse case condition occurs at VIN = 2VOUT, where: IC1 = MP4458 Rev. 1.02 3/4/2013 ILOAD 2 The output capacitor is required to maintain the DC output voltage. Ceramic, tantalum, or low ESR electrolytic capacitors are recommended. Low ESR capacitors are preferred to keep the output voltage ripple low. The output voltage ripple can be estimated by: ΔVOUT = VOUT ⎛ V × ⎜1 − OUT f S × L1 ⎜⎝ VIN ⎞ ⎞ ⎛ 1 ⎟ ⎟⎟ × ⎜ R ESR + ⎜ 8 × f S × C2 ⎟⎠ ⎠ ⎝ Where L is the inductor value, CO is the output capacitance value, and RESR is the equivalent series resistance (ESR) value of the output capacitor. In the case of ceramic capacitors, the impedance at the switching frequency is dominated by the capacitance. The output voltage ripple is mainly caused by the capacitance. For simplification, the output voltage ripple can be estimated by: ΔVOUT = ⎞ ⎛ V × ⎜⎜1 − OUT ⎟⎟ VIN ⎠ × L1 × C2 ⎝ VOUT 8 × fS 2 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 11 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER In the case of tantalum or electrolytic capacitors, the ESR dominates the impedance at the switching frequency. For simplification, the output ripple can be approximated to: ΔVOUT = VOUT ⎛ V ⎞ × ⎜1 − OUT ⎟ × RESR fS × L1 ⎝ VIN ⎠ The characteristics of the output capacitor also affect the stability of the regulation system. The MP4458 can be optimized for a wide range of capacitance and ESR values. Compensation Components MP4458 employs current mode control for easy compensation and fast transient response. The system stability and transient response are controlled through the COMP pin. COMP pin is the output of the internal error amplifier. A series capacitor-resistor combination sets a pole-zero combination to control the characteristics of the control system. The DC gain of the voltage feedback loop is given by: A VDC = R LOAD × G CS × A VEA × VFB VOUT Where AVEA is the error amplifier voltage gain, GCS is the current sense transconductance, and RLOAD is the load resistor value. The system has two poles of importance. One is due to the compensation capacitor (C3), the output resistor of error amplifier. The other is due to the output capacitor and the load resistor. These poles are located at: fP1 = GEA 2π × C3 × A VEA fP2 = 1 2π × C2 × R LOAD and MP4458 Rev. 1.02 3/4/2013 The system has one zero of importance, due to the compensation capacitor (C3) and the compensation resistor (R3). This zero is located at: f Z1 = 1 2π × C3 × R3 The system may have another zero of importance, if the output capacitor has a large capacitance and/or a high ESR value. The zero, due to the ESR and capacitance of the output capacitor, is located at: fESR = 1 2π × C2 × R ESR In this case (as shown in Figure 2), a third pole set by the compensation capacitor (C6) and the compensation resistor (R3) is used to compensate the effect of the ESR zero on the loop gain. This pole is located at: f P3 = 1 2π × C6 × R3 The goal of compensation design is to shape the converter transfer function to get a desired loop gain. The system crossover frequency where the feedback loop has the unity gain is important. Lower crossover frequencies result in slower line and load transient responses, while higher crossover frequencies could cause system unstable. A good rule of thumb is to set the crossover frequency to approximately onetenth of the switching frequency or lower. The Table 4 lists the typical values of compensation components for some standard output voltages with various output capacitors and inductors. The values of the compensation components have been optimized for fast transient responses and good stability at given conditions. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 12 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER VOUT L CO R3 C3 C6 1.8V 4.7µH 47µF ceramic 105k 100pF None 2.5V 4.7µH6.8µH 22µF ceramic 54.9k 220pF None 6.8µH10µH 15µH22µH 22µH33µH 22µF ceramic 22µF ceramic 22µF ceramic 68.1k 220pF None 100k 150pF None 147k 150pF None 3.3V 5V 12V Note: The selection of L is based on fs = 500KHz. Please refer to “Inductor section” on page7 to select proper inductor if fs is higher than that. To optimize the compensation components for conditions not listed in Table 3, the following procedure can be used. 1. Choose the compensation resistor (R3) to set the desired crossover frequency. Determine the R3 value by the following equation: R3 = 2π × C2 × f C VOUT × G EA × G CS VFB Where fC is the desired crossover frequency (which typically has a value no higher than 1/10th of switching frequency). 2. Choose the compensation capacitor (C3) to achieve the desired phase margin. For applications with typical inductor values, setting the compensation zero, fZ1, below one forth of the crossover frequency provides sufficient phase margin. Determine the C3 value by the following equation: C3 > If this is the case, then add the second compensation capacitor (C6) to set the pole fP3 at the location of the ESR zero. Determine the C6 value by the equation: C6 = C2 × R ESR R3 High Frequency Operation The switching frequency of MP4458 can be programmed up to 4MHz by an external resistor. Please pay attention to the following if the switching frequency is above 2MHz. The minimum on time of MP4458 is about 80ns (typ). Pulse skipping operation can be seen more easily at higher switching frequency due to the minimum on time. Recommended operating voltage at 4MHz is 12V or below, and 24V or below at 2MHz. Input Max vs Switching Frequency 30 MAX INPUT VOLTAGE (V) Table 4—Compensation Values for Typical Output Voltage/Capacitor Combinations 25 20 VO=3.3V 15 10 5 1.5 VO=2.5V 2.0 2.5 3.0 fS (MHz) 3.5 4.0 Figure 2—Recommended Input vs. fS 4 2π × R3 × f C Where R3 is the compensation resistor value. 3. Determine if the second compensation capacitor (C6) is required. It is required if the ESR zero of the output capacitor is located at less than half of the switching frequency, or the following relationship is valid: f 1 < S 2π × C2 × R ESR 2 MP4458 Rev. 1.02 3/4/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 13 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER Since the internal bootstrap circuitry has higher impedance, which may not be adequate to charge the bootstrap capacitor during each charging period, an external bootstrap charging diode is strongly recommended if the switching frequency is above 2MHz (see External Bootstrap Diode section for detailed implementation information). With higher switching frequencies, the inductive reactance (XL) of a capacitor dominates, such that the ESL of the input/output capacitor determines the input/output ripple voltage at higher switching frequencies. As a result, high frequency ceramic capacitors are strongly recommended as input decoupling capacitors and output filtering capacitors. Layout becomes more important when the device switches at higher frequency. It is essential to place the input decoupling capacitor, catch diode and the MP4458 as close together as possible, with traces that are very short and fairly wide. This can help to greatly reduce the voltage spikes on SW and also lower the EMI noise level. Try to run the feedback trace as far from the inductor and noisy power traces as possible. It is a good idea to run the feedback trace on the side of the PCB opposite of the inductor with a ground plane separating the two. The compensation components should be placed close to the MP4458. Do not place the compensation components close to or under the high dv/dt SW node, or inside the high di/dt power loop. If you have to do so, the proper ground plane must be in place to isolate these nodes. Switching losses are expected to increase at high switching frequencies. To help improve the thermal conduction, a grid of thermal vias can be created right under the exposed pad. It is recommended that they be small (15mil barrel diameter) so that the hole is essentially filled up during the plating process, thus aiding conduction to the other side. Too large a hole can cause solder wicking problems during the reflow soldering process. The pitch (distance between the centers) of several such thermal vias in an area is typically 40mil. MP4458 Rev. 1.02 3/4/2013 PC Board Layout The high current paths (GND, IN and SW) should be placed very close to the device with short, direct and wide traces. The input capacitor needs to be as close as possible to the IN and GND pins. The external feedback resistors should be placed next to the FB pin. Keep the switch node traces short and away from the feedback resistor divider and compensation network. External Bootstrap Diode An external bootstrap diode may enhance the efficiency of the regulator, the applicable conditions of external BST diode are: z VOUT=5V or 3.3V; and z Duty cycle is high: D= VOUT >65% VIN In these cases, an external BST diode is recommended from the output of the voltage regulator to BST pin, as shown in Figure 3 External BST Diode IN4148 BST MP4458 SW CBST L + COUT 5V or 3.3V Figure 3—Add Optional External Bootstrap Diode to Enhance Efficiency The recommended external BST diode is IN4148, and the BST cap is 0.1~1µF. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 14 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER PCB LAYOUT GUIDE PCB layout is very important to achieve stable operation. It is highly recommended to duplicate EVB layout for optimum performance. 2) Bypass ceramic capacitors are suggested to be put close to the VIN Pin. 3) Ensure all feedback connections are short and direct. Place the feedback resistors and compensation components as close to the chip as possible. 4) Route SW away from sensitive analog areas such as FB. 5) Connect IN, SW, and especially GND respectively to a large copper area to cool the chip to improve thermal performance and long-term reliability. If change is necessary, please follow these guidelines and take Figure 4 for reference. 1) Keep the path of switching current short and minimize the loop area formed by Input cap, high-side MOSFET and external switching diode. C4 VIN VIN C1 BST L1 VOUT SW D1 R5 EN EN MP4458 C2 FB R1 R2 R4 COMP FREQ GND R6 C3 R3 MP4458 Typical Application Circuit GND Top Layer Bottom Layer Figure 4―MP4458 Typical Application Circuit and PCB Layout Guide MP4458 Rev. 1.02 3/4/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 15 MP4458 – 1A, 4MHz, 36V STEP-DOWN CONVERTER PACKAGE INFORMATION 3mm x 3mm TQFN10 2.90 3.10 0.30 0.50 PIN 1 ID MARKING 0.18 0.30 2.90 3.10 PIN 1 ID INDEX AREA 1.45 1.75 PIN 1 ID SEE DETAIL A 10 1 2.25 2.55 0.50 BSC 5 6 TOP VIEW BOTTOM VIEW PIN 1 ID OPTION A R0.20 TYP. PIN 1 ID OPTION B R0.20 TYP. 0.70 0.80 0.20 REF 0.00 0.05 SIDE VIEW DETAIL A NOTE: 2.90 0.70 1) ALL DIMENSIONS ARE IN MILLIMETERS. 2) EXPOSED PADDLE SIZE DOES NOT INCLUDE MOLD FLASH. 3) LEAD COPLANARITY SHALL BE 0.10 MILLIMETER MAX. 4) DRAWING CONFORMS TO JEDEC MO-229, VARIATION VEED-5. 5) DRAWING IS NOT TO SCALE. 1.70 0.25 2.50 0.50 RECOMMENDED LAND PATTERN NOTICE: The information in this document is subject to change without notice. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP4458 Rev. 1.02 www.MonolithicPower.com 3/4/2013 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. 16