T4ARBU405M THRU T4ARBU407M TRANSIENT VOLTAGE SUPPRESSORS GPP BRIDGE RECTIFIER VOLTAGE RANGE 600 to 1000 Volts CURRENT 4.0 Amperes FEATURES * Ideal for printed circuit board * Surge overload rating: 130 amperes peak * Mounting position: Any RBU .880 (22.3) .860 (21.8) MECHANICAL DATA .140 (3.56) .130 (3.30) .740 (18.8) .720 (18.3) .512 (13.0) .080 (2.03) .060 (1.52) .160 (4.1) .140 (3.5) * Epoxy: Device has UL flammability classification 94V-O .710 (18.0) .690 (17.5) .085 (2.16) .075 (1.90) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. .210 (5.33) .190 (4.83) Single phase, half wave, 60 Hz, resistive or inductive load. .080 (2.03) .065 (1.65) .050 (1.27) .040 (1.02) .100 (2.54) .085 (2.16) .022 (0.56) .018 (0.46) For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted) SYMBOL T4ARBU405M T4ARBU406M T4ARBU407M UNITS Maximum Recurrent Peak Reverse Voltage RATINGS VRRM 600 800 1000 Volts Maximum RMS Voltage VRMS 420 560 700 Volts VDC 600 800 1000 Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 50 o C (With Heat-sink) Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Current Squarad Time Volts IO 4.0 Amps I FSM 130 Amps I2 t 70 A2/Sec Peak Power Dissipation at T A =25 OC,T P =1mS (Note 1) PPPM Maximum 400 Watts Breakdown Voltage Range at I T =1mA VBR 380~ 420 Volts Maximum Peak Pulse Current IPPM 0.73 Amps Maximum Clamping Voltage at IPPM =0.73A VC 548 Volts Typical Junction Capacitance (Note 3) CJ 40 T J, T STG -55 to + 150 Operating and Storage Temperature Range pF 0 C ELECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 4.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage @T A = 25 o C @T A = 125 o C SYMBOL T4ARBU405M VF IR NOTES : 1. Non-repetitive current pulse, per Fig.8 and derated above TA=25OC per Fig.7. 2. "Fully ROHS compliant", "100% Sn plating (Pb-free)". 3. Measured at 1MHz and applied reverse voltage of 4.0 voltage. 4. Available in Halogen-free epoxy by adding suffix -HF after the part nbr. T4ARBU406M 1.1 T4ARBU407M UNITS Volts 5.0 500 uAmps 2010-05 REV:O 4.0 Heatsink Mounting, TC 1.6x1.6x0.06" Thk (4.0x4.0x.15cm) AL.Plate 3.0 2.0 P.C.B. Mounted,TA 0.47x0.47" (12x12mm) Copper Pads 0.375" (9.5mm) Lead Length 60Hz Resistive or Inductive Load 1.0 0 0 50 100 150 INSTANTANEOUS FORWARD CURRENT, (A) AVERAGE FORWARD OUTPUT CURRENT, (A) RATING AND CHARACTERISTICS CURVES ( T4ARBU405M THRU T4ARBU407M ) 40 10 4.0 1.0 0.4 0.1 0 O TEMPERATURE, ( C) 10 TA = 25 OC 1.0 50~400V 600~1000V 20 40 60 80 100 120 PEAK FORWARD SURGE CURRENT, (A) INSTANTANEOUS REVERSE CURRENT, (uA) TA = 100 OC 0 140 TRANSIENT THERMAL IMPEDANCE, (OC/W) JUNCTION CAPACITANCE, (pF) 1000 100 1 2.0 2.5 3.0 3.5 10 REVERSE VOLTAGE, (V) FIG.5 TYPICAL JUNCTION CAPACITANCE PER LEG 8.3mS Single Half Sine-Wave JEDEC Method 200 160 120 80 40 0 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.3 TYPICAL REVERSE CHARACTERISTICS 0.1 1.5 240 PERCENT RATED PEAK REVERSE VOLTAGE, (%) 10 1.0 FIG.2 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1000 0.1 0.5 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG.1 DERATING CURVE OUTPUT RECTIFIED CURRENT 100 T A = 25 OC Pulse Width = 300mS 1% Duty Cycle 100 FIG.4 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 100 10 1 0.1 0.01 0.1 1 10 t, HEATING TIME (sec.) FIG.6 TYPICAL TRANSIENT THERMA IMPEDANCE 100 RATING AND CHARACTERISTICS CURVES ( T4ARBU405M THRU T4ARBU407M ) 100 10 1.0 0.1 0.1u 1.0u 10u 100u 1m 75 50 25 0 0 10u 75 100 125 150 175 FIG.7 PEAK PULSE POWER RATING CURVE FIG.8 PULSE DERATING CURVE 100000 Pulse Width (td) is Defined as the Point Where the Peak Current Decays to 50% of I PPM Peak Value IPPM 100 HALF VALUE - IPPM 2 10/1000usec. Waveform as Defined by R.E.A. 50 1.0 2.0 3.0 1000 4.0 200 f = 1MHz Vsig = 50mVp-p TJ= 25 OC 10000 td 0 50 AMBIENT TEMPERATURE, (OC) tr = 10usec. 0 25 PULSE WIDTH,(S) 150 PEAK PULSE CURRENT, (%) PEAK PULSE POWER OR CURRETN DERATING IN PERCENTAGE, (%) Non-Repetitive Pulse Waveform Shown in Fig.3 TA=25OC CJ, CAPACITANCE, (pF) PEAK PULSE POWER, (KW) 100 100 1.0 Measured at Zero Bias Measured at Stand off Voltage,VWM 10 100 200 V(BR), BREAKDOWN VOLTAGE, (V) TIME, (mS) FIG.10 TYPICAL JUNCTION CAPACITANCE FIG.9 PULSE WAVEFORM Schematic DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.