TVS 3KP SERIES GPP TRANSIENT VOLTAGE SUPPRESSOR 3000 WATT PEAK POWER 8.0 WATTS STEADY STATE FEATURES * * * * * * Plastic package has underwriters laboratory Glass passivated chip construction 3000 watt surage capability at 1ms Excellent clamping capability Low zener impedance Fast response time R-6 1.0 (25.4) MIN. .052 (1.3) DIA. .048 (1.2) .360 (9.1) .340 (8.6) .360 (9.1) .340 (8.6) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. DIA. 1.0 (25.4) MIN. Dimensions in inches and (millimeters) DEVICES FOR BIPOLAR APPLICATIONS For Bidirectional use C or CA suffix for types 3KP5.0 thru 3KP110 Electrical characteristics apply in both direction MAXIMUM RATINGS (At T A = 25oC unless otherwise noted) SYMBOL VALUE UNITS Peak Pulse Power Dissipation with a 10/1000uS waveform (Note 1, FIG.1) P PPM Minimum 3000 Watts Peak Pulse Current with a 10/1000uS waveform (Note 1, Fig. 3) I PPM SEE TABLE 1 Amps PM(AV) 8.0 Watts I FSM 250 Amps T J , T STG -55 to + 175 RATINGS Steady State Power Dissipation at TL = 75 oC lead lengths 0.375” (9.5mm) (Note 2) Peak Forward Surge Current, 8.3ms single half sine wavesuperimposed on rated load( JEDEC METHOD ) (Note 3) Operating and Storage Temperature Range o NOTES : 1. Non-repetitive current pulse, per Fig.3 and derated above TA = 25 C per Fig.2. 2. Mounted on copper pad area of 0.8 X 0.8” ( 20 X 20mm ) per Fig. 5 3. Measured on 8.3mS single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum. 0 C 2009-02 REV: O RATING AND CHARACTERISTIC CURVES( 3KP5.0 THRU 3KP110A ) 10 1.0 0.1 0.1uS 1.0uS 10uS 100uS 1.0mS 10mS TP, PULSE WIDTH, sec 100 (IPP) DERATING IN PERCENTAGE,% Non-Repetitive Pulse Waveform Shown in Fig.3 TA = 25 FIG. 2 - PULSE DERATING CURVE PEAK PULSE POWER (PPP) OR CURRENT PPPM, PEAK PULSE POWER, kW FIG. 1 - PEAK PULSE POWER RATING CURVE 100 75 50 25 0 02 f = 1.0 MHz Vsig = 50mVp-p TJ = 25 Pulse Width (td) is Defined as the Point Where the Peak Current Decays to 50% of IPPM CJ, CAPACITANCE, pF IPPM, PEAK PULSE CURRENT,% 100 125 150 175 200 ) FIG. 4 - TYPICAL JUNCTION CAPACITANCE Peak Value IPPM 100 IPPM HALF VALUE 2 10/1000usec. Waveform as Defined by R.E.A. 50 1.0 2.0 t, TIME,mS 3.0 Measured at Stand off Voltage,VWM 1000 td 0 100 4.0 L = 0.375"(9.5mm) Lead Lengths 60Hz Resistive or Inductive Load 6 4 0.8X0.8X0.040" (20X20mm) Copper Heat Sinks 2 0 25 50 75 100 125 150 TL, LEAD TEMPERATURE ( 175 ) 200 IFSM, PEAK FORWARD SURGE CURRENT AMPERES 8 Measured at Zero Bias 10000 1.0 FIG. 5 - STEADY STATE POWER DERATING CURVE PM(AV), STEADY STATE POWER DISSIATION, WATTS 75 100000 tr = 10usec. 0 50 TA, AMBIENT TEMPERATURE,( FIG. 3 - PULSE WAVEFORM 150 0 5 10 100 200 V(BR), BREAKDOWN VOLTACE, VOLTS FIG. 6 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT UNIDIRECTIONAL 300 8.3ms Single Half Sine-Wave (JEDED Method) 250 200 150 100 50 0 1 10 NUMBER OF CYCLES AT 60 Hz 100 TRANSIENT VOLTAGE SUPPRESSORS 3000W SERIES TVS DIODES/R-6 ( CASE 12 ) 3000W TYPE 3KP5.0 3KP5.0A 3KP6.0 3KP6.0A 3KP6.5 3KP6.5A 3KP7.0 3KP7.0A 3KP7.5 3KP7.5A 3KP8.0 3KP8.0A 3KP8.5 3KP8.5A 3KP9.0 3KP9.0A 3KP10 3KP10A 3KP11 3KP11A 3KP12 3KP12A 3KP13 3KP13A 3KP14 3KP14A 3KP15 3KP15A 3KP16 3KP16A 3KP17 3KP17A 3KP18 3KP18A 3KP20 3KP20A 3KP22 3KP22A 3KP24 3KP24A 3KP26 3KP26A 3KP28 3KP28A 3KP30 3KP30A MIN. MAX. (mA) Reverse Stand off Voltage VWM (Volts) 6.40 6.40 6.67 6.67 7.22 7.22 7.78 7.78 8.33 8.33 8.89 8.89 9.44 9.44 10.0 10.0 11.1 11.1 12.2 12.2 13.3 13.3 14.4 14.4 15.6 15.6 16.7 16.7 17.8 17.8 18.9 18.9 20.0 20.0 22.2 22.2 24.4 24.4 26.7 26.7 28.9 28.9 31.1 31.1 33.3 33.3 7.30 7.00 8.15 7.37 8.82 7.98 9.51 8.60 10.2 9.21 10.9 9.83 11.5 10.4 12.2 11.1 13.6 12.3 14.9 13.5 16.3 14.7 17.6 15.9 19.1 17.2 20.4 18.5 21.8 19.7 23.1 20.9 24.4 22.1 27.1 24.5 29.8 26.9 32.6 29.5 35.3 31.9 38.0 34.4 40.7 36.8 50 50 50 50 50 50 50 50 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.5 6.5 7.0 7.0 7.5 7.5 8.0 8.0 8.5 8.5 9.0 9.0 10.0 10.0 11.0 11.0 12.0 12.0 13.0 13.0 14.0 14.0 15.0 15.0 16.0 16.0 17.0 17.0 18.0 18.0 20.0 20.0 22.0 22.0 24.0 24.0 26.0 26.0 28.0 28.0 30.0 30.0 Breakdown Voltage VBR @IT (Volts) Maximum Reverse Leakage at VWM ID(uA) Maximum Peak Pulse Current IPPM (Amps) Maximum Clamping Voltage at IPPM VC (Volts) 2000 2000 5000 5000 2000 2000 1000 1000 250 250 150 150 50 50 20 20 15 15 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 312.5 326 263 291 244 267.8 225.5 250 209.7 232.5 200 220.6 188.7 208.3 177.5 194.8 159.6 176.4 149.2 164.8 136.4 150.7 126 139.5 116.3 129.3 111.5 122.9 104.2 115.4 98.4 108.7 93.2 102.7 83.8 92.6 76.1 84.5 69.7 77.1 64.4 71.2 59.9 66.1 56 62 9.6 9.2 11.4 10.3 12.3 11.2 13.3 12.0 14.3 12.9 15.0 13.6 15.9 14.4 16.9 15.4 18.8 17.0 20.1 18.2 22.0 19.9 23.8 21.5 25.8 23.2 26.9 24.4 28.8 26.0 30.5 27.6 32.2 29.2 35.8 32.4 39.4 35.5 43.0 38.9 46.6 42.1 50.1 45.4 53.5 48.4 TRANSIENT VOLTAGE SUPPRESSORS 3000W SERIES TVS DIODES/R-6 ( CASE 12 ) 3000W TYPE 3KP33 3KP33A 3KP36 3KP36A 3KP40 3KP40A 3KP43 3KP43A 3KP45 3KP45A 3KP48 3KP48A 3KP51 3KP51A 3KP54 3KP54A 3KP58 3KP58A 3KP60 3KP60A 3KP64 3KP64A 3KP70 3KP70A 3KP75 3KP75A 3KP78 3KP78A 3KP85 3KP85A 3KP90 3KP90A 3KP100 3KP100A 3KP110 3KP110A Notes : Breakdown Voltage VBR @IT (Volts) MIN. MAX. (mA) Reverse Stand off Voltage VWM (Volts) 36.7 36.7 40.0 40.0 44.4 44.4 47.8 47.8 50.0 50.0 53.3 53.3 56.7 56.7 60.0 60.0 64.4 64.4 66.7 66.7 71.1 71.1 77.8 77.8 83.3 83.3 86.7 86.7 94.4 94.4 100 100 111 111 122 122 44.9 40.6 48.9 44.2 54.3 49.1 58.4 52.8 61.1 55.3 65.2 58.9 69.3 62.7 73.3 66.3 78.7 71.2 81.5 73.7 96.9 78.6 95.1 86.0 102 92.1 106 95.8 115 104 122 111 136 123 149 135 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 33.0 33.0 36.0 36.0 40.0 40.0 43.0 43.0 45.0 45.0 48.0 48.0 51.0 51.0 54.0 54.0 58.0 58.0 60.0 60.0 64.0 64.0 70.0 70.0 75.0 75.0 78.0 78.0 85.0 85.0 90.0 90.0 100 100 110 110 Maximum Reverse Leakage at VWM ID(uA) Maximum Peak Pulse Current IPPM (Amps) Maximum Clamping Voltage at IPPM VC (Volts) 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 50.8 56.3 46.6 51.6 42.0 46.5 39.1 43.2 37.3 41.3 35.1 38.7 32.9 36.4 31.2 34.4 29.1 31.9 28.0 30.9 26.3 29.1 24.0 26.5 22.4 24.8 21.6 23.8 19.8 21.9 18.7 20.5 16.7 18.5 15.3 16.9 59.0 53.3 64.3 58.1 71.4 64.5 76.7 69.4 80.3 72.7 85.5 77.4 91.1 82.4 96.3 87.1 103 94 107 97 114 103 125 113 134 121 139 126 151 137 160 146 179 162 196 177 1. VBR measured after IT applied for 300us. IT = square pulse or equivalent. 2. All devices UL listed under file# E211196. 3. For bidirectional use C or CA suffixs for all type (ex. 3KP5.0C,3KP110CA) electrical characteristics apply in both directions. 4. For bidirectional types having VWM of 10 volts and less, the ID limit is doubled. DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.