P6KE510A GPP TRANSIENT VOLTAGE SUPPRESSOR 600 WATT PEAK POWER 5.0 WATTS STEADY STATE FEATURES * * * * * * Plastic package has underwriters laboratory Glass passivated chip construction 600 watt surage capability at 1ms Excellent clamping capability Low zener impedance Fast response time DO-15 .034 (0.9) 1.0 (25.4) .028 (0.7) DIA. MIN. .300 (7.6) .230 (5.8) .140 (3.6) .104 (2.6) DIA. 1.0 (25.4) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS MIN. Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load, For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted) SYMBOL VALUE UNITS Peak Power Dissipation at TA = 25OC,TP = 1mS (Note 1) P PPM Minimum 600 W Steady State Power Dissipation at TL = 75OC lead length, .375" (9.5 mm) (Note 2) P M(AV) 5.0 W I FSM 100 A RATINGS Peak forward surge current, 8.3ms single half sine wave superimpose on rated load (JEDEC METHOD) (Note 3) Maximum instantaneous forward voltage at 50A for unidirectional only Operating and Storage Temperature Range VF 5.0 T J, T STG -55 to + 150 NOTES : 1. Non-repetitive current pulse, per Fig.3 and derated above TA = 25o C per Fig.2. 2. Mounted on 0.2 X 0.2” (5.0 X 5.0mm) copper pad to each terminal. 3. Measured on 8.3ms single half sine-wave or equivalent square wave duty cycle=4 pulses per minute maximum. 4. "Fully ROHS compliant", "100% Sn plating (Pb-free)". V 0 C 2007-6 PPPM, PEAK PULSE POWER, (KW) 100 Non-Repetitive Pulse Waveform Shown in Fig.3 TA= 25 OC 10 1.0 0.1 0.1uS 1.0uS 10uS 1.0uS 100uS 10uS PEAK PULSE POWER (PPP) OR CURRENT (IPP) DERATING IN PERCENTAGE, (%) RATING AND CHARACTERISTICS CURVES ( P6KE510A ) 100 75 50 25 0 0 25 Pulse Width (td) is Defined as the Point Where the Peak Current Decays to 50% of IPPM Peak Value IPPM 100 HALF VALUE 0 IPPM 2 10/1000usec. Waveform as Defined by R.E.A. 50 td 0 1.0 2.0 3.0 t, TIME, (mS) FIG.3 PULSE WAVEFORM 100 125 150 175 200 4.0 FIG.2 PULSE DERATING CURVE 10000 CJ, JUNCTION CAPACITANCE, (pF) IPPM, PEAK PULSE CURRENT, (%) tr = 10usec. 75 O FIG.1 PEAK PULSE POWER RATING CURVE 150 50 TA, AMBIENT TEMPERATURE, ( C) TP, PULSE WIDTH, (sec) f = 1MHz Vsig = 50mVp-p TJ= 25 OC Measured at Zero Bias 1000 100 10 1.0 Measured at Stand off Voltage,VWM 10 100 200 V(BR), BREAKDOWN VOLTAGE, (V) FIG.4 TYPICAL JUNCTION CAPACITANCE BIDIRECTIONAL TRANSIENT VOLTAGE SUPPRESSORS 600W SERIES TVS DIODES / DO-15 ( CASE 8 ) 600W TYPE Breakdown Voltage VBR @IT (Volts) MIN. P6KE510A MAX. 484.5 535.5 (mA) Reverse Stand off Voltage VWM (Volts) Maximum Reverse Leakage at VWM ID(uA) Maximum Peak Pulse Current IPPM (Amps) Maximum Clamping Voltage at IPPM VC (Volts) 10 433.5 5 0.84 714 DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.