RFM SF2214E

Preliminary
SF2214E
• Low-loss 815 MHz Filter
• Complies with Directive 2002/95/EC (RoHS)
Pb
815.00 MHz
SAW Filter
Absolute Maximum Ratings
Rating
Value
Units
+10
dBm
5
V
Operating Temperature Range
-30 to +80
°C
Storage Temperature Range in Tape and Reel
-40 to +85
°C
265
°C
Input Power Level
DC Voltage on any Non-ground Terminal
Maximum Soldering Profile, 5 cycles/10 seconds maximum
SM3030-6
Electrical Characteristics
Characteristic
Sym
Notes
Min
Typ
Max
Units
Center Frequency
fC
815.00
Insertion Loss, 805 to 825 MHz
IL
2.8
3.5
dB
1.0
2.0
dB
1.9:1
2.5:1
Peak-to-Peak Amplitude Ripple, 805 to 825 MHz
Input/Output VSWR, 805 to 825 MHz
SWR
MHz
Attenuation, Referenced to 0 dB:
10 to 780 MHz
40
63
851 to 856 MHz
28
50
856 to 869 MHz
40
47
869 to 896 MHz
52
45
896 to 941MHz
40
62
960 to 2200 MHz
40
46
2200 to 2600 MHz
30
35
dB
Source Impedance
ZS
50
Ω
Load Impedance
ZL
50
Ω
Case Style
SM3030-6 3.0 x 3.0 mm Nominal Footprint
Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator
Standard Reel Quantity
950, YWWS
Reel Size 7 inch
500 Pieces/Reel
Reel Size 13 inch
3000 Pieces/Reel
Electrical Connections
Connection
Input
Terminals
2
Output
5
Case Ground
All others
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 Ω and measured with 50 Ω network analyzer.
Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
"LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
The design, manufacturing process, and specifications of this filter are subject to change.
Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
US and international patents may apply.
RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
www.RFM.com E-mail: [email protected]
©2009-2010 by RF Monolithics, Inc.
Page 1 of 5
SF2214E - 7/19/10
Filter Passband Response
Filter Broadband Response
www.RFM.com E-mail: [email protected]
©2009-2010 by RF Monolithics, Inc.
Page 2 of 5
SF2214E - 7/19/10
Filter Input VSWR Plot
Filter Output VSWR Plot
www.RFM.com E-mail: [email protected]
©2009-2010 by RF Monolithics, Inc.
Page 3 of 5
SF2214E - 7/19/10
SM3030-6 Case
6-Terminal Ceramic Surface-Mount Case
3.0 X 3.0 mm Nominal Footprint
Case and PCB Footprint Dimensions
Dimension
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
K
L
N
K
N
mm
Nom
3.00
3.00
1.25
0.90
2.80
1.60
0.85
1.50
0.60
1.30
3.20
1.70
1.05
0.81
0.38
Min
2.87
2.87
1.12
0.77
2.67
1.47
0.72
1.37
0.47
1.17
Max
3.13
3.13
1.38
1.03
2.93
1.73
0.98
1.63
0.73
1.43
Inches
Nom
0.118
0.118
0.049
0.035
0.110
0.063
0.033
0.059
0.024
0.051
0.126
0.067
0.041
0.032
0.015
Min
0.113
0.113
0.044
0.030
0.105
0.058
0.028
0.054
0.019
0.046
Max
0.123
0.123
0.054
0.040
0.115
0.068
0.038
0.064
0.029
0.056
Case Materials
O
Materials
N
M
M
PCB Footprint Top View
Solder Pad
Plating
0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel
Lid Plating
2.0 to 3.0 µm Nickel
Body
Al2O3 Ceramic
Pb Free
TOP VIEW
BOTTOM VIEW
B
1
3
6
950
YWWS
A 2
5
E
4
D
www.RFM.com E-mail: [email protected]
©2009-2010 by RF Monolithics, Inc.
G
C
F
H
6
1
5
2
4
3
I
J
Page 4 of 5
SF2214E - 7/19/10
Tape and Reel Specifications
“B”
millimeters
Quantity Per Reel
7
178
500
13
330
3000
"B" REF.
100 REF.
Inches
See Detail "A"
13.
0
12.0
20
.2
2.0
COMPONENT ORIENTATION and DIMENSIONS
Carrier Tape Dimensions
Ao
Bo
Ko
Pitch
W
2.0
4.0
PIN #1
A
1.50
1.75
0.3 ± 0.05
3.35 mm
3.35 mm
1.40 mm
8.0 mm
12.0 mm
Bo
B
Ao
12.0
5.5
RO.3
(MAX.)
B
Pitch
A
Ko
R0.5
(MAX.)
1.5
SECTION A-A
SECTION B-B
www.RFM.com E-mail: [email protected]
©2009-2010 by RF Monolithics, Inc.
USER DIRECTION OF FEED
Page 5 of 5
SF2214E - 7/19/10