Preliminary SF2206E • No Matching Network Required for 50 Ω Operation • Surface-mount 3.0 x 3.0 mm Package • Complies with Directive 2002/95/EC (RoHS) Pb 2655 MHz SAW Filter Absolute Maximum Ratings Value Units Input Power Level Rating 10 dBm DC Voltage on any Non-ground Terminal 0 V Operating Temperature Range -40 to +85 °C Storage Temperature Range in Tape and Reel -40 to +85 °C 260 °C Solder Reflow Temperature, 10 seconds, 5 cycles maximum SM3030-6 Electrical Characteristics Characteristic Sym Notes Min Typ Max Center Frequency fC 2655 Insertion Loss, 2620.0 to 2690.0 MHz IL 2.0 3.0 0.9 2.0 Amplitude Ripple, 2620.0 to 2690.0 MHz Input/Output Return Loss, 2620.0 to 2690.0 MHz 8 13 2322.0 to 2402.0 MHz 33 36 2480.0 to to 2500.0 MHz 35 37 2500.0 to 2550.0 MHz 10 20 Units MHz dB dB Attenuation, 0 dB Reference: 3000.0 to 3600.0 MHz 30 36 Source Impedance ZS 50 Load Impedance ZL 50 Case Style Ω SM3030-6 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator Standard Reel Quantity dB 938, YWWS Reel Size 7 Inch 500 Pieces/Reel Reel Size 13 Inch 3000 Pieces/Reel Electrical Connections Connection Terminals Input 5 Output 2 Case Ground All others 1 6 5 0 o h m S o u rc e 5 4 (b o tto m 5 0 o h m L o a d 2 3 v ie w ) CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. 7. 8. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc., are registered trademarks of RF Monolithics, Inc. www.RFM.com E-mail: [email protected] ©2009-2011 by RF Monolithics, Inc. Page 1 of 6 SF2206E - 3/10/11 Filter Passband Response, 2400 to 2900 MHz Filter Response, 700 to 4600 MHz www.RFM.com E-mail: [email protected] ©2009-2011 by RF Monolithics, Inc. Page 2 of 6 SF2206E - 3/10/11 Filter Input Return Loss, 2400 to 2900 MHz Filter Output Return Loss, 2400 to 2900 MHz www.RFM.com E-mail: [email protected] ©2009-2011 by RF Monolithics, Inc. Page 3 of 6 SF2206E - 3/10/11 Filter Input Smith Chart, 2400 to 2900 MHz Filter Output Smith Chart, 2400 to 2900 MHz www.RFM.com E-mail: [email protected] ©2009-2011 by RF Monolithics, Inc. Page 4 of 6 SF2206E - 3/10/11 SM3030-6 Case 6-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint Case and PCB Footprint Dimensions Dimension A B C D E F G H I J K L M N O K L N K N mm Nom 3.00 3.00 1.25 0.90 2.80 1.60 0.85 1.50 0.60 1.30 3.20 1.70 1.05 0.81 0.38 Min 2.87 2.87 1.12 0.77 2.67 1.47 0.72 1.37 0.47 1.17 Max 3.13 3.13 1.38 1.03 2.93 1.73 0.98 1.63 0.73 1.43 Inches Nom 0.118 0.118 0.049 0.035 0.110 0.063 0.033 0.059 0.024 0.051 0.126 0.067 0.041 0.032 0.015 Min 0.113 0.113 0.044 0.030 0.105 0.058 0.028 0.054 0.019 0.046 Max 0.123 0.123 0.054 0.040 0.115 0.068 0.038 0.064 0.029 0.056 Case Materials O Materials N M M PCB Footprint Top View Solder Pad Plating 0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel Lid Plating 2.0 to 3.0 µm Nickel Body Al2O3 Ceramic Pb Free TOP VIEW BOTTOM VIEW B 1 3 6 938 YWWS A 2 5 E 4 D www.RFM.com E-mail: [email protected] ©2009-2011 by RF Monolithics, Inc. G C F H 6 1 5 2 4 3 I J Page 5 of 6 SF2206E - 3/10/11 Tape and Reel Specifications Quantity Per Reel Inches millimeters 7 178 500 13 330 3000 "B" REF. 100 REF. “B” See Detail "A" 13. 0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao Bo Ko Pitch W 2.0 4.0 PIN #1 A 1.50 1.75 0.3 ± 0.05 3.35 mm 3.35 mm 1.40 mm 8.0 mm 12.0 mm Bo B Ao 12.0 5.5 RO.3 (MAX.) B Pitch A Ko R0.5 (MAX.) 1.5 SECTION A-A SECTION B-B www.RFM.com E-mail: [email protected] ©2009-2011 by RF Monolithics, Inc. USER DIRECTION OF FEED Page 6 of 6 SF2206E - 3/10/11