RT9711
80mΩ
Ω, 1.5A High-Side Power Switches with Flag
General Description
Features
The RT9711 is a low voltage, single N-MOSFET high-side
power switch, optimized for self-powered and bus- powered
Universal Serial Bus (USB) applications. The RT9711
equipped with a charge pump circuitry to drive the internal
MOSFET switch; the switch's low RDS(ON), 80mΩ, meets
z
Compliant to USB Specifications
z
Built-In N-MOSFET
Ω (SOT-23-5), 90mΩ
Ω (SOP-8)
` Typical RDS(ON) : 80mΩ
Output Can Be Forced Higher Than Input (Off-State)
Low Supply Current :
25μ
μA Typical at Switch On State
1μ
μA Typical at Switch Off State
Guaranteed 1.5A Continuous Load Current
Wide Input Voltage Ranges : 2.5V to 5.5V
Open-Drain Fault Flag Output
Hot Plug-In Application (Soft-Start)
1.7V Typical Under-Voltage Lockout (UVLO)
Current Limiting Protection
Thermal Shutdown Protection
Reverse Current Flow Blocking (no body diode)
UL Approved−E219878
RoHS Compliant and 100% Lead (Pb)-Free
USB voltage drop requirements; and a flag output is
available to indicate fault conditions to the local USB
controller.
Additional features include soft-start to limit inrush current
during plug-in, thermal shutdown to prevent catastrophic
switch failure from high-current loads, under-voltage
lockout (UVLO) to ensure that the device remains off
unless there is a valid input voltage present. The maximum
current is limited to typically 2.5A in dual ports in
accordance with the USB power requirements, lower
quiescent current as 25μA making this device ideal for
portable battery-operated equipment.
The RT9711 is available in SOT-23-5 and SOP-8 packages
requiring minimum board space and smallest components.
z
z
z
z
z
z
z
z
z
z
z
z
Applications
z
z
Ordering Information
z
RT9711
z
Package Type
B : SOT-23-5
S : SOP-8
Lead Plating System
P : Pb Free
G : Green (Halogen Free and Pb Free)
Note :
z
z
z
z
USB Bus/Self Powered Hubs
USB Peripherals
ACPI Power Distribution
PC Card Hot Swap
Notebook, Motherboard PCs
Battery-Powered Equipment
Hot-Plug Power Supplies
Battery-Charger Circuits
Pin Configurations
(TOP VIEW)
Richtek products are :
`
RoHS compliant and compatible with the current requirements of IPC/JEDEC J-STD-020.
`
VOUT
VIN
5
4
Suitable for use in SnPb or Pb-free soldering processes.
2
3
FLG GND EN
Marking Information
For marking information, contact our sales representative
directly or through a Richtek distributor located in your
area.
SOT-23-5
GND
8
VOUT
VIN
2
7
VOUT
VIN
3
6
VOUT
EN
4
5
FLG
SOP-8
DS9711-07 April 2011
www.richtek.com
1
RT9711
Test Circuits
Typical Application Circuit
Pull-Up Resistor (10K to 100K)
RFG
USB Controller
Supply
Voltage 5V
VIN
VIN
+
1µF
Over -Current
FLG
RT9711
VOUT
EN
GND
OFF
EN
ON
GND
Ferrite
Beads
RT9711
VBUS
D+
D-
150µF
10µF
VFLG
FLG
VOUT
VOUT
GND
+
ON
CIN
+
OFF
VIN
COUT
RL
IL
Data
Note: A low-ESR 150μF aluminum electrolytic or tantalum
between VOUT and GND is strongly recommended to meet
the 330mV maximum droop requirement in the hub VBUS.
(see Application Information Section for further details)
Functional Pin Description
Pin No.
Pin Name
Pin Function
RT9711□B RT9711□ S
1
5
FLG
Open-Drain Fault Flag Output
2
1
GND
Ground
3
4
EN
Chip Enable (Active Low)
4
2, 3
VIN
Power Input Voltage
5
6, 7, 8
VOUT
Output Voltage
Function Block Diagram
VIN
EN
Bias
UVLO
Oscillator
Charge
Pump
Thermal
Protection
Current
Limiting
Gate
Control
Output Voltage
Detection
VOUT
FLG
Delay
GND
www.richtek.com
2
DS9711-07 April 2011
RT9711
Absolute Maximum Ratings
z
z
z
z
z
z
z
z
z
(Note 1)
Supply Voltage --------------------------------------------------------------------------------------------------------- 6.5V
Chip Enable Input Voltage ------------------------------------------------------------------------------------------- −0.3V to 6.5V
Flag Voltage ------------------------------------------------------------------------------------------------------------ 6.5V
Power Dissipation, PD @ TA = 25°C
SOT-23-5 ---------------------------------------------------------------------------------------------------------------- 0.4W
SOP-8 -------------------------------------------------------------------------------------------------------------------- 0.625W
Package Thermal Resistance (Note 2)
SOT-23-5, θJA ---------------------------------------------------------------------------------------------------------- 250°C/W
SOP-8, θJA -------------------------------------------------------------------------------------------------------------- 160°C/W
Junction Temperature ------------------------------------------------------------------------------------------------- 125°C
Lead Temperature (Soldering, 10 sec.) --------------------------------------------------------------------------- 260°C
Storage Temperature Range ---------------------------------------------------------------------------------------- −65°C to 150°C
ESD Susceptibility (Note 3)
HBM (Human Body Mode) ------------------------------------------------------------------------------------------ 2kV
MM (Machine Mode) -------------------------------------------------------------------------------------------------- 200V
Recommended Operating Conditions
z
z
z
z
(Note 4)
Supply Input Voltage -------------------------------------------------------------------------------------------------- 2.5V to 5.5V
Chip Enable Input Voltage ------------------------------------------------------------------------------------------- 0V to 5.5V
Junction Temperature Range ---------------------------------------------------------------------------------------- −40°C to 125°C
Ambient Temperature Range ---------------------------------------------------------------------------------------- −40°C to 85°C
Electrical Characteristics
(VIN = 5V, CIN = COUT = 1μF, TA = 25°C, unless otherwise specified)
Parameter
Switch On Resistance
Symbol
SOT23-5
SOP-8
Supply Current
Test Conditions
Min
Typ
Max
--
80
100
--
90
110
R DS(ON)
VIN = 5V, IOUT = 1A
ISW_ON
Switch on, VOUT = Open
--
25
45
ISW_OFF
Switch off, VOUT = Open
--
0.1
1
Unit
mΩ
μA
Logic-Low Voltage
EN
Threshold Logic-High Voltage
V IL
VIN = 2V to 5.5V, switch on
--
--
0.8
V
V IH
VIN = 2V to 5.5V, switch off
2.0
--
--
V
EN Input Current
IEN
VEN = 0V to 5.5V
--
0.01
--
μA
Output Leakage Current
ILEAKAGE VEN = 5V, RLOAD = 0Ω
--
0.5
10
μA
Output Turn-On Rise Time
TON_RISE 10% to 90% of V OUT rising
Current Ramp (< 0.1A/ms) on
ILIM
VOUT
--
400
--
μs
1.6
2.5
3.2
A
Current Limit
Short Circuit Fold-Back Current
(Hysteresis)
ISC_FB
VOUT = 0V, measured prior to
thermal shutdown
--
1.0
--
A
FLAG Output Resistance
R FLG
ISINK = 1mA
--
20
400
Ω
FLAG Off Current
IFLG_OFF
VFLG = 5V
--
0.01
1
μA
To be continued
DS9711-07 April 2011
www.richtek.com
3
RT9711
Parameter
Test Conditions
Min
Typ
Max
Unit
tD
From fault condition to FLG assertion
5
12
20
ms
Under-Voltage Lockout
V UVLO
VIN increasing
1.3
1.7
--
V
Under-Voltage Hysteresis
ΔVUVLO
VIN decreasing
--
0.1
--
V
Thermal Shutdown Protection
T SD
--
130
--
°C
Thermal Shutdown Hysteresis
ΔT SD
--
20
--
°C
FLAG Delay Time
Symbol
(Note 5)
Note 1. Stresses listed as the above "Absolute Maximum Ratings" may cause permanent damage to the device. These are for
stress ratings. Functional operation of the device at these or any other conditions beyond those indicated in the
operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended
periods may remain possibility to affect device reliability.
Note 2. θJA is measured in the natural convection at TA = 25°C on a low effective single layer thermal conductivity test board of
JEDEC 51-3 thermal measurement standard.
Note 3. Devices are ESD sensitive. Handling precaution is recommended.
Note 4. The device is not guaranteed to function outside its operating conditions.
Note 5. The FLAG delay time is input voltage dependent, see“ Typical Operating Characteristics” graph for further details.
www.richtek.com
4
DS9711-07 April 2011
RT9711
Typical Operating Characteristics
Switch On Resistance vs. Temperature
Switch On Resistance vs. Temperature
0.25
SOP-8, VIN = 5V, ILOAD = 1.5A
CIN = 1μF/X7R, COUT = 10μF/X7R
Switch On Resistance (Ω)
Switch On Resistance (Ω)
0.25
0.2
0.15
0.1
0.05
SOT-23-5, VIN = 5V, ILOAD = 1.5A
CIN = 1μF/X7R, COUT = 10μF/X7R
0.2
0.15
0.1
0.05
0
0
-40
-20
0
20
40
60
80
100
-40
120
-20
0
20
Temperature (°C)
Supply Current (uA)
Switch on Resistance (mΩ)
35
100
80
60
40
120
SOT-23-5, VEN = 0V, RL = Open
CIN = COUT = 33μF/Electrolytic
30
25
20
15
10
0
2
2.5
3
3.5
4
4.5
5
2
5.5
2.5
3
Input Voltage (V)
3.5
4
4.5
5
5.5
Input Voltage (V)
Current Limit vs. Input Voltage
Supply Current vs. Temperature
30
3
25
2.5
Current Limit (A)
Supply Current (uA)
100
5
20
20
15
10
5
80
Supply Current vs. Input Voltage
40
SOT-23-5, ILOAD = 1.5A
CIN = COUT = 33μF/Electrolytic
120
60
Temperature (°C)
Switch on Resistance vs. Input Voltage
140
40
SOT-23-5
VIN = 5V, VEN = 0V, RL = Open
CIN = COUT = 33μF/Electrolytic
SOT-23-5
VIN = 5V, VEN = 0V, RL = 2.2Ω
CIN = 1μF/X7R, COUT = 10μF/X7R
2
1.5
1
0.5
0
0
-40
-20
0
20
40
60
Temperature (°C)
DS9711-07 April 2011
80
100
120
2
2.5
3
3.5
4
4.5
5
5.5
Input Voltage (V)
www.richtek.com
5
RT9711
EN PinThreshold Voltage vs. Input Voltage
Current Limit vs. Temperature
3.25
EN Threshold Voltage (V)
VIN = 5V, VEN = 0V, RL = 2.2Ω
CIN = 1μF/X7R, COUT = 10μF/X7R
3
Current Limit (A)
2
2.75
SOP-8
2.5
SOT-23-5
2.25
2
1.75
1.5
SOT-23-5, Switch Off
CIN = COUT = 33μF/Electrolytic
ILOAD = 100mA
1.6
1.2
0.8
0.4
0
-40
-20
0
20
40
60
80
100
120
2
2.5
3
Temperature (°C)
Turn-Off Leakage Current (uA)
EN Pin Threshold Voltage (V)
1.6
1.2
0.8
0.4
5
5.5
3.5
3
SOT-23-5, VIN = VEN = 5V
CIN = 33μF/Electrolytic
COUT = 1μF/X7R
RL = 0Ω
2.5
2
1.5
1
0.5
0
0
-40
-20
0
20
40
60
80
100
-40
120
-20
0
Temperature (°C)
40
60
80
100
120
Turn-Off Falling Time vs. Temperature
100
SOT-23-5, VIN = 5V, RL = 30Ω
CIN = 33μF/Electrolytic
COUT = 1μF/Electrolytic
Turn-Off Falling Time (us)
600
20
Temperature (°C)
Turn-On Rising Time vs. Temperature
700
Turn-On Rising Time (us)
4.5
Turn-Off Leakage Current vs. Temperature
4
SOT-23-5, VIN = 5V, ILOAD = 100mA
CIN = COUT = 33μF/Electrolytic
2
4
Input Voltage (V)
EN Pin Threshold Voltage vs. Temperature
2.4
3.5
500
400
300
200
100
80
SOT-23-5, VIN = 5V, RL = 30Ω
CIN = 33μF/Electrolytic
COUT = 1μF/Electrolytic
60
40
20
0
0
-40
-20
0
20
40
60
Temperature (°C)
www.richtek.com
6
80
100
120
-40
-20
0
20
40
60
80
100
120
Temperature (°C)
DS9711-07 April 2011
RT9711
Swith Off Supply Current vs. Temperature
UVLO Threshold vs. Temperature
2.4
SOT-23-5, VIN = VEN = 5V
CIN = COUT = 33μF/Electrolytic
RL = Open
0.8
0.6
2
UVLO Threshold (V)
Swith Off Supply Current (uA)
1
0.4
0.2
0
-0.2
-0.4
-0.6
1.6
1.2
0.8
SOT-23-5, VIN Increasing
VEN = 0V, ILOAD = 15mA
CIN = COUT = 33μF/Electrolytic
0.4
-0.8
0
-1
-40
-20
0
20
40
60
80
100
-40
120
-20
0
Temperature (°C)
20
40
60
80
100
120
Temperature (°C)
Flag Delay Time vs. Input Voltage
Flag Delay Time vs. Temperature
16
20
Flag Delay Time (ms)
Flag Delay Time (ms)
15
16
12
8
4
14
13
12
11
10
SOT-23-5, VEN = 0V
CIN = COUT = 33μF/Electrolytic
9
SOT-23-5, VIN = 5V, VEN = 0V
CIN = COUT = 33μF/Electrolytic
8
7
0
2
2.5
3
3.5
4
4.5
5
-40
5.5
-20
0
20
40
60
80
100
120
Temperature
Input Voltage (V)
Current Limit Transient Response
Load Transient Response
SOT-23-5, VIN = 5V
VEN = 0V, RL = 2Ω
CIN = COUT = 33μF/Electrolytic
4.8V
1.5A
VOUT
(1V/Div)
IOUT
(1A/Div)
IOUT
(1A/Div)
Time (50μs/Div)
DS9711-07 April 2011
SOT-23-5, VIN = 5V
VEN = 0V, COUT = 1μF
CIN = 33μF/Electrolytic
RL = 1kΩ ≥ 2.2Ω
Time (1ms/Div)
www.richtek.com
7
RT9711
Turn On Response
Turn Off Response
SOT-23-5, VIN = 5V, RL = 30Ω
CIN = 33μF/Electrolytic
COUT = 1μF/Electrolytic
SOT-23-5, VIN = 5V, RL = 30Ω
CIN = 33μF/Electrolytic
COUT = 1μF/Electrolytic
VEN
(5V/Div)
VEN
(5V/Div)
VOUT
(5V/Div)
VOUT
(5V/Div)
IOUT
(200mA/Div)
Time (100μs/Div)
Time (100μs/Div)
UVLO at Rising
UVLO at Falling
SOT-23-5, VIN = 5V, VEN = 0V
CIN = 33μF/Electrolytic, COUT = 1μF
RL = 30Ω
SOT-23-5, VIN = 5V, VEN = 0V
CIN = 33μF/Electrolytic, COUT = 1μF
RL = 30Ω
VIN
(1V/Div)
VIN
(1V/Div)
VOUT
(1V/Div)
VOUT
(1V/Div)
Time (1ms/Div)
Time (5ms/Div)
Flag Response during Short Circuit
Flag Response during Over Load
SOT-23-5, VIN = 5V, RL = 0Ω
CIN = COUT = 33μF/Electrolytic
VEN
(5V/Div)
VFLG
(5V/Div)
VOUT
(5V/Div)
10ms
IOUT
(1A/Div)
12ms
VFLG
(5V/Div)
IOUT
(1A/Div)
Time (5ms/Div)
www.richtek.com
8
SOT-23-5, VIN = 5V, RL = 2Ω
CIN = COUT = 33μF/Electrolytic
Time (5ms/Div)
DS9711-07 April 2011
RT9711
Flag Response with Ramped Load
SOT-23-5, VIN = 5V, VEN = 0V
CIN = COUT = 33μF/Electrolytic
VEN
(5V/Div)
VLAG
(5V/Div)
VOUT
(5V/Div)
IOUT
(1A/Div)
Time (2.5ms/Div)
DS9711-07 April 2011
www.richtek.com
9
RT9711
Applications Information
The RT9711 is a single N-MOSFET high-side power switch
with active-low enable input, optimized for self-powered
and bus-powered Universal Serial Bus (USB) applications.
The RT9711 equipped with a charge pump circuitry to drive
the internal N-MOSFET switch; the switch's low RDS(ON),
80mΩ, meets USB voltage drop requirements; and a flag
output is available to indicate fault conditions to the local
USB controller.
Input and Output
VIN (input) is the power source connection to the internal
circuitry and the drain of the MOSFET. VOUT (output) is
the source of the MOSFET. In a typical application, current
flows through the switch from VIN to VOUT toward the load.
If VOUT is greater than VIN, current will flow from VOUT to
VIN since the MOSFET is bidirectional when on.
Unlike a normal MOSFET, there is no a parasitic body
diode between drain and source of the MOSFET, the
RT9711 prevents reverse current flow if VOUT being
externally forced to a higher voltage than VIN when the
output disabled (VEN > 2V).
D
S
S
D
G
G
Normal MOSFET
RT9711
Chip Enable Input
The switch will be disabled when the EN pin is in a logic
high condition. During this condition, the internal circuitry
and MOSFET are turned off, reducing the supply current
to 0.1μA typical. The maximum guaranteed voltage for a
logic low at the EN pin is 0.8V. A minimum guaranteed
voltage of 2V at the EN pin will turn the RT9711 off. Floating
the input may cause unpredictable operation. EN should
not be allowed to go negative with respect to GND.
www.richtek.com
10
Soft Start for Hot Plug-In Applications
In order to eliminate the upstream voltage droop caused
by the large inrush current during hot-plug events, the
“soft-start” feature effectively isolates the power source
from extremely large capacitive loads, satisfying the USB
voltage droop requirements.
Fault Flag
The RT9711 provides a FLG signal pin which is an
N-Channel open drain MOSFET output. This open drain
output goes low when VOUT < VIN − 1V, current limit or
the die temperature exceeds 130°C approximately. The
FLG output is capable of sinking a 10mA load to typically
200mV above ground. The FLG pin requires a pull-up
resistor, this resistor should be large in value to reduce
energy drain. A 100kΩ pull-up resistor works well for most
applications. In the case of an over-current condition, FLG
will be asserted only after the flag response delay time,
tD, has elapsed. This ensures that FLG is asserted only
upon valid over-current conditions and that erroneous error
reporting is eliminated.
For example, false over-current conditions may occur
during hot-plug events when extremely large capacitive
loads are connected and causes a high transient inrush
current that exceeds the current limit threshold. The FLG
response delay time tD is typically 12ms.
Under-Voltage Lockout
Under-voltage lockout (UVLO) prevents the MOSFET
switch from turning on until input voltage exceeds
approximately 1.7V. If input voltage drops below
approximately 1.6V, UVLO turns off the MOSFET switch,
FLG will be asserted accordingly. Under-voltage detection
functions only when the switch is enabled.
Current Limiting and Short-Circuit Protection
The current limit circuitry prevents damage to the MOSFET
switch and the hub downstream port but can deliver load
current up to the current limit threshold of typically 2.5A
through the switch of RT9711. When a heavy load or short
circuit is applied to an enabled switch, a large transient
current may flow until the current limit circuitry responds.
DS9711-07 April 2011
RT9711
Thermal Shutdown
Thermal shutdown is employed to protect the device from
damage if the die temperature exceeds approximately
130°C. The power switch will auto-recover when the IC is
coolng down. The thermal hysteresis temperature is about
20°C.
Power Dissipation
The device’ s junction temperature depends on several
factors such as the load, PCB layout, ambient temperature
and package type. The output pin of RT9711 can deliver a
current up to 1.5A, respectively over the full operating
junction temperature range. However, the maximum output
current must be derated at higher ambient temperature to
ensure the junction temperature does not exceed 125°C.
With all possible conditions, the junction temperature must
be within the range specified under operating conditions.
Power dissipation can be calculated based on the output
current and the RDS(ON) of switch as below.
2
PD = RDS(ON) x (IOUT)
Although the devices are rated for 1.5A of output current,
but the application may limit the amount of output current
based on the total power dissipation and the ambient
temperature. The final operating junction temperature for
any set of conditions can be estimated by the following
thermal equation :
PD (MAX) = ( TJ(MAX) − TA ) / θJA
Where T J(MAX) is the maximum operation junction
temperature 125°C, TA is the ambient temperature and the
θJA is the junction to ambient thermal resistance.
The junction to ambient thermal resistance θJA is layout
dependent. For SOT-23-5 packages, the thermal
resistance θJA is 250°C/W on the standard JEDEC 51-3
single-layer thermal test board.
And for SOP-8 packages, the thermal resistance θJA is
160°C/W. The maximum power dissipation at TA = 25°C
can be calculated by following formula :
PD(MAX) = ( 125°C − 25°C) / 250°C/W = 0.4 W for
SOT-23-5 packages
DS9711-07 April 2011
PD(MAX) = ( 125°C − 25°C) / 160°C/W = 0.625 W for
SOP-8 packages
The maximum power dissipation depends on operating
ambient temperature for fixed T J(MAX) and thermal
resistance θJA. For RT9711 packages, the Figure 1 of
derating curves allows the designer to see the effect of
rising ambient temperature on the maximum power
allowed.
0.7
Maximum Power Dissipation (W)
Once this current limit threshold is exceeded the device
enters constant current mode until the thermal shutdown
occurs or the fault is removed.
Single Layer PCB
0.6
SOP-8
0.5
0.4
0.3
0.2
SOT-23-5
0.1
0
0
25
50
75
100
125
Ambient Temperature (°C)
Figure 1. Derating Curves for RT9711 Package
Universal Serial Bus (USB) & Power Distribution
The goal of USB is to enable devices from different vendors
to interoperate in an open architecture. USB features
include ease of use for the end user, a wide range of
workloads and applications, robustness, synergy with the
PC industry, and low-cost implement- ation. Benefits
include self-identifying peripherals, dynamically attachable
and reconfigurable peripherals, multiple connections
(support for concurrent operation of many devices), support
for as many as 127 physical devices, and compatibility
with PC Plug-and-Play architecture.
The Universal Serial Bus connects USB devices with a
USB host: each USB system has one USB host. USB
devices are classified either as hubs, which provide
additional attachment points to the USB, or as functions,
which provide capabilities to the system (for example, a
digital joystick). Hub devices are then classified as either
Bus-Power Hubs or Self-Powered Hubs.
www.richtek.com
11
RT9711
A Bus-Powered Hub draws all of the power to any internal
functions and downstream ports from the USB connector
power pins. The hub may draw up to 500mA from the
upstream device. External ports in a Bus-Powered Hub
can supply up to 100mA per port, with a maximum of four
external ports.
Self-Powered Hub power for the internal functions and
downstream ports does not come from the USB, although
the USB interface may draw up to 100mA from its
upstream connect, to allow the interface to function when
the remainder of the hub is powered down. The hub must
be able to supply up to 500mA on all of its external
downstream ports. Please refer to Universal Serial
Specification Revision 2.0 for more details on designing
compliant USB hub and host systems.
Over-Current protection devices such as fuses and PTC
resistors (also called polyfuse or polyswitch) have slow
trip times, high on-resistance, and lack the necessary
circuitry for USB-required fault reporting.
The faster trip time of the RT9711 power distribution allow
designers to design hubs that can operate through faults.
The RT9711 have low on-resistance and internal faultreporting circuitry that help the designer to meet voltage
regulation and fault notification requirements.
Because the devices are also power switches, the designer
of self-powered hubs has the flexibility to turn off power to
output ports. Unlike a normal MOSFET, the devices have
controlled rise and fall times to provide the needed inrush
current limiting required for the bus-powered hub power
switch.
Supply Filter/Bypass Capacitor
A 1μF low-ESR ceramic capacitor from VIN to GND,
located at the device is strongly recommended to prevent
the input voltage drooping during hot-plug events. However,
higher capacitor values will further reduce the voltage droop
on the input. Furthermore, without the bypass capacitor,
an output short may cause sufficient ringing on the input
(from source lead inductance) to destroy the internal
control circuitry. The input transient must not exceed 6.5V
of the absolute maximum supply voltage even for a short
duration.
www.richtek.com
12
Output Filter Capacitor
A low-ESR 150μF aluminum electrolytic or tantalum
between VOUT and GND is strongly recommended to meet
the 330mV maximum droop requirement in the hub VBUS
(Per USB 2.0, output ports must have a minimum 120μF
of low-ESR bulk capacitance per hub). Standard bypass
methods should be used to minimize inductance and
resistance between the bypass capacitor and the
downstream connector to reduce EMI and decouple voltage
droop caused when downstream cables are hot-insertion
transients. Ferrite beads in series with VBUS, the ground
line and the 0.1μF bypass capacitors at the power
connector pins are recommended for EMI and ESD
protection. The bypass capacitor itself should have a low
dissipation factor to allow decoupling at higher frequencies.
Voltage Drop
The USB specification states a minimum port-output
voltage in two locations on the bus, 4.75V out of a SelfPowered Hub port and 4.4V out of a Bus-Powered Hub
port. As with the Self-Powered Hub, all resistive voltage
drops for the Bus-Powered Hub must be accounted for to
guarantee voltage regulation (see Figure 7-47 of Universal
Serial Specification Revision 2.0 ).
The following calculation determines VOUT (MIN) for multiple ports (NPORTS) ganged together through one switch (if
using one switch per port, NPORTS is equal to 1) :
VOUT (MIN) = 4.75V
− [ II x ( 4 x RCONN + 2 x RCABLE ) ] −
(0.1A x NPORTS x RSWITCH )
− VPCB
Where
RCONN : Resistance of connector contacts
(two contacts per connector)
RCABLE : Resistance of upstream cable wires
(one 5V and one GND)
RSWITCH : Resistance of power switch
(80mΩ typical for RT9711)
VPCB : PCB voltage drop
DS9711-07 April 2011
RT9711
The USB specification defines the maximum resistance
per contact (RCONN) of the USB connector to be 30mΩ
and the drop across the PCB and switch to be 100mV.
This basically leaves two variables in the equation : the
resistance of the switch and the resistance of the cable.
If the hub consumes the maximum current (II) of 500mA,
the maximum resistance of the cable is 90mΩ.
The resistance of the switch is defined as follows :
RSWITCH = { 4.75V
− 4.4V − [ 0.5A x ( 4 x 30mΩ + 2 x
90mΩ) ]
− VPCB } ÷ ( 0.1A x NPORTS )
= (200mV − VPCB ) ÷ ( 0.1A x NPORTS )
If the voltage drop across the PCB is limited to 100mV,
the maximum resistance for the switch is 250mΩ for four
ports ganged together. The RT9711, with its maximum
100mΩ on-resistance over temperature, easily meets this
requirement.
Layout Considerations
For best performance of the RT9711, the following
guidelines muse be strictly followed :
` Input and output capacitors should be placed close to
the IC and connected to ground plane to reduce noise
coupling.
` The GND should be connected to a strong ground plane
for heat sink.
` Keep the main current traces as possible as short and
wide.
The input and output capacitors should be
placed as close as possible to the IC.
V IN
V OUT
GND
V IN
FLG
GND
EN
Figure 2. PCB Layout Guide
DS9711-07 April 2011
www.richtek.com
13
RT9711
Outline Dimension
H
D
L
B
C
b
A
A1
e
Symbol
Dimensions In Millimeters
Dimensions In Inches
Min
Max
Min
Max
A
0.889
1.295
0.035
0.051
A1
0.000
0.152
0.000
0.006
B
1.397
1.803
0.055
0.071
b
0.356
0.559
0.014
0.022
C
2.591
2.997
0.102
0.118
D
2.692
3.099
0.106
0.122
e
0.838
1.041
0.033
0.041
H
0.080
0.254
0.003
0.010
L
0.300
0.610
0.012
0.024
SOT-23-5 Surface Mount Package
www.richtek.com
14
DS9711-07 April 2011
RT9711
H
A
M
J
B
F
C
I
D
Dimensions In Millimeters
Dimensions In Inches
Symbol
Min
Max
Min
Max
A
4.801
5.004
0.189
0.197
B
3.810
3.988
0.150
0.157
C
1.346
1.753
0.053
0.069
D
0.330
0.508
0.013
0.020
F
1.194
1.346
0.047
0.053
H
0.170
0.254
0.007
0.010
I
0.050
0.254
0.002
0.010
J
5.791
6.200
0.228
0.244
M
0.400
1.270
0.016
0.050
8-Lead SOP Plastic Package
Richtek Technology Corporation
Richtek Technology Corporation
Headquarter
Taipei Office (Marketing)
5F, No. 20, Taiyuen Street, Chupei City
5F, No. 95, Minchiuan Road, Hsintien City
Hsinchu, Taiwan, R.O.C.
Taipei County, Taiwan, R.O.C.
Tel: (8863)5526789 Fax: (8863)5526611
Tel: (8862)86672399 Fax: (8862)86672377
Email: [email protected]
Information that is provided by Richtek Technology Corporation is believed to be accurate and reliable. Richtek reserves the right to make any change in circuit
design, specification or other related things if necessary without notice at any time. No third party intellectual property infringement of the applications should be
guaranteed by users when integrating Richtek products into any application. No legal responsibility for any said applications is assumed by Richtek.
DS9711-07 April 2011
www.richtek.com
15