RT9718 Over Voltage Protection IC General Description Features The RT9718 is an integrated circuit optimized to protect low voltage system from abnormal high input voltage (up to 28V). The IC monitors the input voltage, battery voltage and the charging current to make sure all three parameters are operated in normal range. When the input voltage exceeds a certain OVP threshold voltage level, the IC will turn off the power MOSFET within 1μs to remove the power before any damage occurs. The RT9718 also can provide a voltage output without the existence of battery. z The IC also monitors the battery voltage, Once the battery voltage exceeds 4.35V and last for more then 180us blinking time, the RT9718 will turn off the MOSFET. The internal logic control will turn off the power MOSFET permanently when the battery over-voltage event occurs for consecutive 16 times. Ordering Information RT9718 Note : Programmable OCP ` Input OVP ` Battery OVP Withstand High Input Voltage Up to 28V Over Voltage Turn Off Time Less Than 1us High Accuracy Protection Thresholds Over Temperature Protection High Immunity of False Triggering Under Transients Warning Indication Output Enable Input Thermal Enhanced WDFN Package RoHS Compliant and Halogen Free ` z z z z z z z z z Applications z z z z Cellular Phones Digital Cameras PDAs and Smart Phones Portable Instruments Pin Configurations (TOP VIEW) VIN GND NC WRN 1 2 3 4 GND The current in the power MOSFET is also limited to prevent charging the battery with an excessive current. The current limit can be programmed by an external resistor between ILIM and GND. The OCP function also has a 4-bit binary counter that accumulates during an OCP event. When the total count reaches consecutive 16 times, the power MOSFET is turned off permanently unless the input power is recycled. Fully Integrated Protection Function 9 8 7 6 5 VOUT ILIM VB EN WDFN-8L 2x2 Package Type QW : WDFN-8L 2x2 (W-Type) Lead Plating System G : Green (Halogen Free and Pb Free) Z : ECO (Ecological Element with Halogen Free and Pb free) OVP A : 6.80V B : 5.85V C : 6.25V D : 7.20V Marking Information For marking information, contact our sales representative directly or through a Richtek distributor located in your area. Richtek products are : ` RoHS compliant and compatible with the current requirements of IPC/JEDEC J-STD-020. ` Suitable for use in SnPb or Pb-free soldering processes. DS9718-02 May 2011 www.richtek.com 1 RT9718 Typical Application Circuit RT9718 1 VIN VIN VOUT 8 CIN 1µF 5 Chip Enable VB 6 7 ILIM 4 WRN EN 2 GND Charger IC (RT9502) COUT 1µF To System RVB 200k + RILIM 25k Battery Functional Pin Description Pin No. Pin Name Pin Function 1 VIN The input power source. The VIN can withstand up to 28V input. 2 GND Analog Ground. 3 NC No Internal Connection. 4 WRN This is an open-drain logic output that turns LOW when any protection event occurs. 5 EN 6 VB Battery voltage monitoring input. This pin is connected to the battery pack positive terminal via an isolation resistor. 7 ILIM Over current protection threshold setting pin. Connect a resistor between this pin and GND to set the OCP threshold. 8 VOUT Output through the power MOSFET. Chip Enable (Active Low). Pull this pin to low or leave it floating to enable the IC and force it to high to disable the IC. The exposed pad must be soldered to a large PCB and connected to GND for maximum thermal dissipation. 9 (Expose Pad) GND Function Block Diagram VIN VOUT VREF Ibias BASE Driver OCP VDD INOVP UVLO EN Control Logic ILIM Buffer BATOVP VB WRN EN Logic OTP www.richtek.com 2 OCP Seting GND DS9718-02 May 2011 RT9718 Absolute Maximum Ratings z z z z z z z z z (Note 1) Supply Input Voltage, VIN -------------------------------------------------------------------------------------------- −0.3V to 28V VOUT, VB --------------------------------------------------------------------------------------------------------------- −0.3V to 7V Other Pins --------------------------------------------------------------------------------------------------------------- −0.3V to 6V Power Dissipation, PD @ TA = 25°C WDFN-8L 2x2 ---------------------------------------------------------------------------------------------------------- 0.606W Package Thermal Resistance (Note 2) WDFN-8L 2x2, θJA ----------------------------------------------------------------------------------------------------- 165°C/W WDFN-8L 2x2, θJC ---------------------------------------------------------------------------------------------------- 20°C/W Junction Temperature ------------------------------------------------------------------------------------------------- 150°C Lead Temperature (Soldering, 10 sec.) --------------------------------------------------------------------------- 260°C Storage Temperature Range ---------------------------------------------------------------------------------------- −65°C to 150°C ESD Susceptibility (Note 3) HBM (Human Body Mode) ------------------------------------------------------------------------------------------ 2kV MM (Machine Mode) -------------------------------------------------------------------------------------------------- 200V Recommended Operating Conditions z z (Note 4) Junction Temperature Range ---------------------------------------------------------------------------------------- −40°C to 125°C Ambient Temperature Range ---------------------------------------------------------------------------------------- −40°C to 85°C Electrical Characteristics (VIN = 5V, TA = 25°C, unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max 4 -- 6.5 Unit Power On Reset RT9718A Operation Voltage RT9718B RT9718C VIN RT9718D Supply Voltage POR Threshold VPOR VPOR Rising Deglitch Time of POR 4 -- 5.5 4 -- 5.9 4 -- 6.9 2.5 2.7 2.9 V -- 8 -- ms 2.45 -- 2.75 V Under Voltage Lockout Threshold VUVLO VUVLO Falling Input Quiescent Current IQ EN = 0V -- 500 600 Input Shutdown Current ISHDN EN = 5V -- 65 95 V μA Protections RT9718A 6.6 6.8 7 Input OVP RT9718B 5.6 5.85 6 Threshold Voltage RT9718C 6.05 6.25 6.45 7 7.2 7.4 -- 60 100 mV -- -- 1 μs -- 8 -- ms VIN_OVP RT9718D Input OVP Hysteresis Input OVP Propagation Delay Input OVP Recovery Delay VOUT = VIN x 80% V To be continued DS9718-02 May 2011 www.richtek.com 3 RT9718 Parameter Symbol Over Current Protection IOCP Over Current Protection Blanking Time Over Current Recover Delay Battery Over Voltage Protection Test Conditions Min Typ Max Unit 0.93 1 1.07 A -- 180 -- μs -- 64 -- ms 4.3 4.35 4.4 V -4.225 30 -- --- mV V --- 180 8 --- μs ms VVB = 4.4V -- -- 20 nA Rising -- 140 -- °C Hysteresis -- 20 -- °C --- 8 8 --- ms ms 1.5 -- --- -0.4 V V 100 200 400 kΩ -- 0.35 0.8 V -- -- 1 μA -- 200 300 mΩ As RILIM = 25k TOC Threshold Rising VBOVP Hysteresis Battery OVP Falling Threshold Battery OVP Blanking Time Battery OVP Recover Delay TVBOV VB Pin Leakage Current OTP Threshold TSD OTP Recover Delay Soft-Start Time Logic EN Threshold Voltage Logic-High VIH Logic-Low VIL EN Internal Pull Down Resistor WRN Output Logic Low Sink 5mA WRN Output Logic High Leakage Current Power MOSFET On Resistance RON I OUT = 500mA, 4.3V < VIN < 6.5V Note 1. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Note 2. θJA is measured in the natural convection at TA = 25°C on a low effective single layer thermal conductivity test board of JEDEC 51-3 thermal measurement standard. The case position of θJC is on the exposed pad of the packages. Note 3. Devices are ESD sensitive. Handling precaution is recommended. Note 4. The device is not guaranteed to function outside its operating conditions. www.richtek.com 4 DS9718-02 May 2011 RT9718 Typical Operating Characteristics OCP Threshold vs. Input Voltage Input OVP vs. Temperature 1.10 6.80 OCP Threshold (A) Input OVP (V) 6.78 6.76 6.74 6.72 6.70 1.07 1.04 1.01 0.98 6.68 CIN = COUT = 1μF, RILIM = 25kΩ CIN = COUT = 1μF 0.95 6.66 -50 -25 0 25 50 75 100 4.4 125 4.7 5 5.3 Temperature (°C) Battery OVP vs. Input Voltage 6.2 6.5 6.8 Battery OVP vs. Temperature 4.370 4.365 4.365 4.360 4.360 Battery OVP (V) Battery OVP (V) 5.9 Input Voltage (V) 4.370 4.355 4.350 4.345 4.355 4.350 4.345 4.340 4.340 4.335 4.335 CIN = COUT = 1μF CIN = COUT = 1μF, VIN = 5.5V 4.330 4.330 4.5 4.8 5.1 5.4 5.7 6 6.3 -50 6.6 -25 0 Input Voltage (V) 25 50 75 100 125 Temperature (°C) Quiescent Current vs. Input Voltage Quiescent Current vs. Temperature 600 600 500 500 Quiescent Current (µA) Quiescent Current (µA) 1 5.6 400 300 200 400 300 200 100 100 CIN = COUT = 1μF, VIN = 5.5V CIN = COUT = 1μF 0 0 2.8 3.45 4.1 4.75 5.4 Input Voltage (V) DS9718-02 May 2011 6.05 6.7 -50 -25 0 25 50 75 100 125 Temperature (°C) www.richtek.com 5 RT9718 Shutdown Current vs. Temperature 200 175 175 Shutdown Current (µA)1 Shutdown Current (µA)1 Shutdown Current vs. Input Voltage 200 150 125 100 75 50 150 125 100 75 50 25 25 CIN = COUT = 1μF 0 2.8 3.45 4.1 4.75 5.4 6.05 CIN = COUT = 1μF, VIN = 5.5V 0 -50 6.7 -25 0 25 50 75 Input Voltage (V) Temperature (°C) EN Threshold Voltage vs. Input Voltage Power On 100 125 EN Threshold Voltage (V) 1.20 Logic High 1.16 VIN (5V/Div) 1.12 VOUT (5V/Div) Logic Low 1.08 1.04 CIN = COUT = 1μF WRN (5V/Div) I IN (500mA/Div) CIN = COUT = 1μF 1.00 4.5 4.8 5.1 5.4 5.7 6 6.3 6.6 Time (2.5ms/Div) 6.9 Input Voltage (V) Input OVP Power Off VIN (5V/Div) VIN (10V/Div) VOUT (10V/Div) VOUT (5V/Div) WRN (10V/Div) WRN (5V/Div) IOUT (500mA/Div) IOUT (500mA/Div) CIN = COUT = 1μF Time (1ms/Div) www.richtek.com 6 CIN = COUT = 1μF Time (2.5ms/Div) DS9718-02 May 2011 RT9718 OCP Battery OVP VBATT VIN (5V/Div) VOUT (10V/Div) VBATT (2V/Div) VOUT (5V/Div) WRN (5V/Div) WRN (10V/Div) IOUT (1A/Div) IOUT (500mA/Div) CIN = COUT = 1μF, VIN = 5.5V Time (100ms/Div) DS9718-02 May 2011 CIN = COUT = 1μF, VIN = 5.5V Time (1ms/Div) www.richtek.com 7 RT9718 Applications Information Power Up Battery Over Voltage Protection The RT9718 has a threshold of 2.7V power on reset (POR) with a built-in hysteresis of 100mV. Before the input voltage reaches the POR threshold, the RT9718 is off. When the input voltage is over the POR threshold; the RT9718 will delay for 8ms and the soft-start will be activated after the 8ms delay. The 8ms delay allows any transients at the input during a hot insertion of the power supply to settle down before the IC starts to operate. The battery OVP threshold voltage is set at 4.35V in typical and the RT9718 has a built-in 180us blanking time to prevent any transient voltage from triggering the battery OVP. If the OVP situation still exists after 180us, the internal MOSFET will be turned off and the WRN pin indicates a LOW signal. The battery OVP threshold has a 30mV builtin hysteresis. The control logic contains a 4-bit binary counter. If the battery over voltage event occurs for consecutive 16 times, the MOSFET will be turned off permanently unless the input power or the enable pin is reset. During the soft-start transition, the RT9718 slowly turns on the internal MOSFET to reduce the inrush current. Enable Control The RT9718 offers an enable (EN) input. When the EN pin is pulled to logic high (>1.5V), the RT9718 will be shut down. When the EN pin is pulled to logic low (<0.4V), the RT9718 will be powered on. The EN pin has an internal pull-down resistor. Leaving the EN pin floating can enable the IC. Warning Indication Output The WRN pin is an open-drain output that indicates a LOW signal when any protection event occurs (Input OVP, Output OCP and Battery OVP). When the protection events are released and then the WRN pin indicates a HIGH signal. Over Temperature Protection (OTP) The RT9718 monitors its own internal temperature to prevent thermal failures. The chip turns off the MOSFET when the internal temperature reaches 140°C. The IC will resume after the internal temperature is cooled down 20°C. Input Over Voltage Protection The RT9718 monitors input voltage to prevent the input voltage lead to output system failures. The RT9718 input OVP threshold is set by the internal resistor. When the input voltage exceeds the threshold, the RT9718 outputs a logic signal to turn off the internal MOSFET within 1us to prevent the high input voltage from damaging the electronics in the handheld system. The hysteresis of the input OVP threshold is 100mV. When the input voltage returns to normal operation voltage rage, the RT9718 reenables the MOSFET. www.richtek.com 8 Selecting RVB The RT9718 monitors the battery voltage by the VB pin. The RT9718 will be turned off when the battery voltage exceeds the 4.35V battery OVP threshold. The VB pin is connected to the battery pack positive terminal via an isolation resistor (RVB) and the resistor is an important component. The RVB determines some parameters such as battery OVP threshold error and VB pin leakage current. Generally, it is necessary to decrease the RVB for reducing the battery OVP threshold error. However, this will increase the VB pin leakage current. So, it is an important issue to get a trade-off between the battery OVP threshold error and the VB pin leakage current. The resistance of 200kΩ to 1MΩ is allowed for RVB. Over Current Protection (OCP) The RT9718 monitors the output current to prevent the output short or the charging of the battery with an excessive current. The OCP (Over Current protection) threshold can be set by the ILIM pin. The RT9718 has a built-in 180us delay time to prevent any transient noise from triggering the OCP. If the OCP situation exists for 180us, the internal MOSFET will be turned off and the WRN pin indicates a LOW signal. When the OCP happens for consecutive 16 times, the internal MOSFET will be turned off permanently unless the input power is recycled or the enable pin is toggled. DS9718-02 May 2011 RT9718 To get the better performance of the RT9718, it is very important to select peripherally appropriate capacitors. These capacitors determine some parameters such as input inrush current and input over shoot voltage. Generally, it is necessary to increase the input capacitance CIN for reducing the input over shoot voltage. However, this will increase the inrush current of input. There are two scenarios that can cause the input over shoot voltage. The first one is that when the AC adapter is hot-plugged and the second one is when the RT9718 has a step-down change. The cable between the AC adapter output and the handheld system input has a parasitic inductance causing the input over shoot voltage. Generally, the input over shoot voltage range is 1.5 to 2 times of the input voltage. It is recommended to use 1μF capacitance for CIN and COUT and the rated voltage should be higher than at 1.5 to 2 times of the operation voltage. formula : PD(MAX) = (125°C − 25°C) / (165°C/W) = 0.606W for WDFN8L 2x2 packages The maximum power dissipation depends on operating ambient temperature for fixed TJ(MAX) and thermal resistance θJA. For RT9718 packages, the Figure 1 of derating curves allows the designer to see the effect of rising ambient temperature on the maximum power allowed. 0.8 The maximum power dissipation depends on the thermal resistance of IC package, PCB layout, the rate of surroundings airflow and temperature difference between junction to ambient. The maximum power dissipation can be calculated by following formula : PD(MAX) = ( TJ(MAX) − TA ) / θJA Where T J(MAX) is the maximum operation junction temperature, TA is the ambient temperature and the θJA is the junction to ambient thermal resistance. For recommended operating conditions specification of RT9718, the maximum operating junction temperature is 125°C. The junction to ambient thermal resistance θJA for WDFN-8L 2x2 package is 165°C/W on the standard JEDEC 0.6 0.5 0.4 0.3 0.2 0.1 0 0 25 50 75 100 125 Ambient Temperature (°C) Figure 1. Derating Curves for RT9718 Packages Thermal Considerations Thermal protection limits power dissipation in RT9718. When the operation junction temperature exceeds 140°C, the OTP circuit starts the thermal shutdown function and turns the pass element off. The pass elements turn on again after the junction temperature cools by 20°C. Single Layers PCB 0.7 Layout Consideration For best performance of the RT9718 series, the following guidelines must be strictly followed. ` Input and output capacitors should be placed close to the IC and connected to ground plane to reduce noise coupling. ` The GND and exposed pad should be connected to a strong ground plane for heat sink. ` Keep the main current traces as possible as short and wide. The input and output capacitors should be placed as close as possible to the IC. The main current trace should be as short and wide as possible. C IN VIN GND NC WRN 1 2 3 4 GND Selecting Capacitors 51-3 single-layer thermal test board. The maximum power dissipation at TA =25°C can be calculated by following Power Dissipation (W) The OCP threshold can be set by the resistor connected between the ILIM pin and GND. The OCP threshold can be calculated by the following equation : IOCP = 25000 RILIM 9 8 7 6 5 VOUT ILIM VB EN C OUT V OUT R VB R ILIM GND The exposed pad and GND should be connected to a strong ground plane for heat sinking and noise prevention. Figure 2. PCB Layout Guide DS9718-02 May 2011 www.richtek.com 9 RT9718 Outline Dimension D2 D L E E2 1 SEE DETAIL A 2 e A A1 1 2 1 b DETAIL A Pin #1 ID and Tie Bar Mark Options A3 Note : The configuration of the Pin #1 identifier is optional, but must be located within the zone indicated. Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max A 0.700 0.800 0.028 0.031 A1 0.000 0.050 0.000 0.002 A3 0.175 0.250 0.007 0.010 b 0.200 0.300 0.008 0.012 D 1.950 2.050 0.077 0.081 D2 1.000 1.250 0.039 0.049 E 1.950 2.050 0.077 0.081 E2 0.400 0.650 0.016 0.026 e L 0.500 0.300 0.020 0.400 0.012 0.016 W-Type 8L DFN 2x2 Package Richtek Technology Corporation Richtek Technology Corporation Headquarter Taipei Office (Marketing) 5F, No. 20, Taiyuen Street, Chupei City 5F, No. 95, Minchiuan Road, Hsintien City Hsinchu, Taiwan, R.O.C. Taipei County, Taiwan, R.O.C. Tel: (8863)5526789 Fax: (8863)5526611 Tel: (8862)86672399 Fax: (8862)86672377 Email: [email protected] Information that is provided by Richtek Technology Corporation is believed to be accurate and reliable. Richtek reserves the right to make any change in circuit design, specification or other related things if necessary without notice at any time. No third party intellectual property infringement of the applications should be guaranteed by users when integrating Richtek products into any application. No legal responsibility for any said applications is assumed by Richtek. www.richtek.com 10 DS9718-02 May 2011