UVTOP355 v 2.1 20.09.2013 Description UVTOP355 is a series of AlGaN based deep UV-LEDs with a typical peak wavelength of 365nm and optical output power of 480-800 µW. It comes in hermetically sealed TO39 or TO18 metal can package with ball lens, hemispherical lens, or flat glass window configuration. UVTOP355 is widely used for UV curing, optical sensing, and imaging of dyes, inks and markers. Maximum Ratings (T CASE = 25°C) Parameter Values Symbol Power Dissipation, DC Forward Current, DC Pulsed Current (1% duty cycle, 1kHz) Reverse Voltage Operating Temperature Storage Temperature Soldering Temperature (max. 5s) General Characteristics (T Parameter PD IF IFP UR Topr Tstg Tsol CASE = -6 -30 -30 Max. 180 30 200 +55 +100 +190 Unit mW mA mA V °C °C °C 25°C, IF = 20mA) Symbol Min.* 355 λP ∆λ UF Peak Wavelength Half Width (FWHM) Forward Voltage Min. Values Typ.* 365 15 4.5 Max.* 370 20 6.5 Unit nm nm V *wavelength measurement tolerance: ± 2 nm, forward voltage measurement tolerance: ± 2 % Electro-Optical Characteristics (T Part Number UVTOP355-FW-TO39 UVTOP355-TFW-TO39 UVTOP355-TFWR-TO39 UVTOP355-HL-TO39 UVTOP355-BL-TO39 UVTOP355-FW-TO18 UVTOP355-BL-TO18 Package TO-39 TO-18 CASE = Window Flat Window Flat Window Flat Window Hemisph. Lens Ball Lens Flat Window Ball Lens 25°C, IF = 20mA) Optical Power POUT (µW) Min.* Typ.* 480 800 195 325 390 650 330 550 480 800 480 800 480 800 View. Angle 2Ө1/2 (°) Typ. 120 120 120 7 7 120 10 *output power measurement tolerance: ± 10 % Open Can version (TO18 or TO39, no cap, no window) available on request www.roithner-laser.com 1 Performance Characteristics Normalized output power vs. Wavelength Peak Wavelength vs. Forward Current Forward Voltage vs. Forward Current Output Power vs. Forward Current Normalized Output Power vs. Temperature Normalized Forward Voltage vs. Temperature www.roithner-laser.com 2 Outline Dimensions TO-39 Flat Window All dimensions in mm TO-39 Hemispherical Lens All dimensions in mm TO-39 Ball Lens All dimensions in mm www.roithner-laser.com 3 Outline Dimensions TO-39 Tall Flat Window & Tall Flat Window w. Reflector All dimensions in mm TO-18 Flat Window All dimensions in mm TO-18 Ball Lens All dimensions in mm www.roithner-laser.com 4 Device Materials Part Header Leads Lens Bonding Wires Material Fe-Ni alloy, plated Ni-Au Fe-Ni alloy, plated Ni-Au SiO2 Au Emission Characteristics Flat Window Hemispherical Lens Ball Lens www.roithner-laser.com 5 Precautions Soldering: • • • • • • • • • • Do avoid overheating of the LED Do avoid electrostatic discharge (ESD) Do avoid mechanical stress, shock, and vibration Do only use non-corrosive flux. Do only solder the leads. Soldering of header or cap will damage the LED Do only cut the leads at room temperature with an ESD protected tool Do not solder closer than 3 mm from base of the header Do form leads prior to soldering Do not impose mechanical stress on the header when forming the leads Do not apply current to the LED until it has cooled down to room temperature after soldering Recommended soldering conditions: dip soldering pre-heat time dipping time solder bath temperature hand soldering max 30 s max 5 s max 190 °C soldering time solder temperature max 5 s max 190 °C Above table specifies the maximum allowed duration and temperature during soldering. It is strongly advised to perform soldering at the shortest time and lowest temperature possible. Cleaning: Cleaning with isopropyl alcohol, propanol, or ethyl alcohol is recommended DO NOT USE acetone, chloroseen, trichloroethylene, or MKS DO NOT USE ultrasonic cleaners Static Electricity: UVTOP are sensitive to electrostatic discharge (ESD). Precautions against ESD must be taken when handling or operating these LEDs. Surge voltage or electrostatic discharge can result in complete failure of the device. UV-Radiation: During operation these LEDs do emit high intensity ultraviolet light, which is hazardous to skin and eyes, and may cause cancer. Do avoid exposure to the emitted UV light. Protective glasses are recommended. It is further advised to attach a warning label on products/systems that do utilize UV-LEDs: Class 1 Operation: Do only operate UVTOP LEDs with a current source. Running these LEDs from a voltage source will result in complete failure of the device. Current of a LED is an exponential function of the voltage across it. Usage of current regulated drive circuits is mandatory © All Rights Reserved The above specifications are for reference purpose only and subjected to change without prior notice www.roithner-laser.com 6