MW174KB Universal 40-65 Watt Series Medical / Switch Mode Power Supply 3 Year Warranty •100-240 VAC Universal Input •Desktop Style •Single Output to 65W •Four Models Available; 12V to 24V •Regulated Output with Low Ripple •Impact Resistant Polycarbonate Enclosure •Modified and Custom Designs •Designed to Meet EISA Requirements — see reverse side for details International Safety Standard Approvals Specifications General Specifications Line and Load Regulation (Excluding cord) Line Voltage +/-1% Load Voltage +/-5% Topology Ripple 1% Vp-p max. Efficiency Transient Response 0.5ms for 50% Load change Typical Protection Over-current Protection (Hiccup) Short Circuit Protection Hold-up Time @120VAC 18ms min. Dielectric Withstand Input Specifications ,000VAC or 5,656VDC 4 Primary-Secondary; 1,500VAC or 2,150VDC Primary-F.G; 500VDC Secondary-F.G Input Voltage Range Universal input 100-240VAC -10%, +10% Storage Temp -30° C to 85° C Line Frequency 47-63Hz Input Current 90VAC Input 1.5A max. Protection Internal Primary Current Fuse, Inrush Limiting Approvals and Safety Standards Australian, Japanese certification available - extra fees apply. UL60601-1, IEC/EN60601-1 EMC : EN60601-1-2 EN55024 MTBF 100,000 Calculated Hours Case and Dimension Desktop Style 4.20L x 2.60W x 1.46H (in) 107.0L x 66.0W x 37.0H (mm) Case Material Black 94V0 Polycarbonate Cord and Connectors Output Specifications Environmental Specifications Thermal Performance Operating temperature full load, no derating convectional cooling Non vented case Relative Humidity Non-condensing 5% to 95% Altitude 0-10,000 feet 0° C to 40° C Switching-Fixed Frequency Flyback Designed to Meet EISA Requirements — see reverse side 8 AWG 1,500mm 1 2 Conductor. Ault #3 Connector. Other connectors are also available. SL Power Electronics Corp • 6050 King Drive • Ventura, CA 93003 • Phone:805.486.4565 • Fax:858.712.2040 • Email:[email protected] • www.slpower.com MW174KB Universal 40-65 Watt Series Medical / Switch Mode Power Supply For the most current data and application support visit www.slpower.com Output Current Output Voltage Max Ault Part Number Max Watts Ripple Vp-p max. MW174KB12XX 12 V 5.00 A 60.0 W 120 mV MW174KB15XX 15 V 4.00 A 60.0 W 150 mV MW174KB18XX 18 V 3.40 A 61.2 W 180 mV MW174KB24XX 24 V 2.70 A 64.8 W 240 mV Ault Part Number Key MW174 K B 12 XX Pin Connections Product Family Name Manufacturing Location Design Revision Changes Voltage DC Connector Number Input Configuration IEC320 w/ground C14 (F) IEC320 w/o ground C18 (Q) N. America/ Japan (B) Europe (M) United Kingdom (G) Australian (E) Shaver C8 (N) Pinout Code Center contact: positive Description Switchcraft 760 plug or equivalent Suggested Mating Switchcraft 712A jack or equivalent Other Connectors are available by special order 2007 Energy Independence and Security Act – EISA he Energy Independence and Security Act of 2007 was passed in December T of 2007 and addresses minimum efficiency standards and standby levels for Class A external power supplies that are 250 watts and under. This law stipulates that external power supplies manufactured on July 1, 2008 and beyond meet certain minimum efficiency and standby criteria as defined below. Minimum Efficiency Criteria ctive mode is defined as when a power supply’s input is connected to line A voltage AC and its output is connected to a DC or AC load drawing a portion of the product’s power output. Depending on the power rating for the power supply, it must meet the minimum efficiency criteria outlined below. Energy-Efficiency Criteria for Active Mode: output power on minimum average adapter label efficiency percentage ≥ 0.50 * output power on adapter label 0 to ≤ less than 1 watt ≥ [0.09 * Ln (output power on adapter > 1 to ≤ 51 watts label )] + 0.50 ≥ 0.85 > 51 watts he power supply must also meet a requirement for when its input is T connected to a line voltage AC but its output is not connected to a load. Depending on the power output of the supply, it must keep its energy consumption below the following values. Energy Consumption Criteria for No Load Mode: output power on maximum power consumption adapter label in no-load mode ≤ 0.5 watts 0 to < 250 watts SL Power Electronics Corp • 6050 King Drive • Ventura, CA 93003 • Phone:805.486.4565 • Fax:858.712.2040 • Email:[email protected] • www.slpower.com Data Sheet © 2008 SL Power Electronics Corp. The information and specifications contained in this data sheet are believed to be correct at time of publication. However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice. Rev.6/9/08