DS16EV5110 Video Equalizer for DVI, HDMI, and Cat5 Cables General Description Features The DS16EV5110 is a 2.25 Gbps multi-channel equalizer optimized for video cable extension applications. It contains three Transition-Minimized Differential Signaling (TMDS) data channels and one clock channel as commonly found in DVI and HDMI cables. It provides compensation for skin-effect and dielectric losses, a common phenomenon when transmitting video on commercially available high definition video cables. The inputs and outputs fully support DVI and HDMI requirements and features programmable levels of input equalization. The programmable levels of equalization provide optimal signal boost and reduces inter-symbol interference. The device supports DC-coupled data paths providing a wider input common-mode voltage range. The wide input common-mode voltage range eliminates the need for external coupling capacitors, thereby reducing solution size and cost. The clock channel is optimized for clock rates of up to 225 MHz and features a signal detect circuit. To maximize noise immunity, the DS16EV5110 features a programmable loss of signal threshold. The threshold is adjustable through a Serial Management Bus (SMBus) interface. The DS16EV5110 also provides support for system power management via output enable controls. Additional controls are provided via the SMBus enabling customization and optimization for specific applications requirements. These controls include programmable features such as output amplitude and boost controls as well as system level diagnostics. ■ 8 levels of equalization settable by 3 pins or through the SMBus interface ■ DC-Coupled inputs and outputs ■ Optimized for operation from 250 Mbps to 2.25 Gbps in ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ support of UXGA, 480 I/P, 720 I/P, 1080 I, and 1080 P with 8, 10, and 12–bit Color Depth Resolutions Two DS16EV5110 devices support DVI/HDMI Dual Link DVI 1.0, HDMI 1.2a, and HDMI 1.3 Compatible TMDS Interface Clock channel signal detect (LOS) Enable for power savings standby mode Serial Management Bus (SMBus) provides control of boost, output amplitude, enable, and clock channel signal detect threshold Low power consumption: 475mW (Typical) 0.13 UI total jitter at 1.65 Gbps including cable Single 3.3V power supply Small 7mm x 7mm, 48-pin leadless LLP package -40°C to +85°C operating temperature range Extends TMDS cable reach over: 1. > 40 meters 24 AWG DVI Cable 2. > 20 meters 28 AWG DVI Cable 3. > 20 meters Cat5/Cat5e/Cat6 cables 4. > 20 meters at 2.25 Gbps over 28 AWG HDMI cables Applications ■ ■ ■ ■ DVI/HDMI Cable Extenders / Switchers Digital Routers and Switches Projectors High Definition Displays Typical Application 20216224 © 2007 National Semiconductor Corporation 202162 www.national.com DS16EV5110 Video Equalizer for DVI, HDMI, and Cat5 Cables June 2007 DS16EV5110 Pin Descriptions Pin Name Pin Number I/O, Type Description HIGH SPEED DIFFERENTIAL I/O C_IN− C_IN+ 1 2 I, CML Inverting and non-inverting TMDS Clock inputs to the equalizer. An on-chip 50Ω terminating resistor connects C_IN+ to VDD and C_IN- to VDD. D_IN0− D_IN0+ 4 5 I, CML Inverting and non-inverting TMDS Data inputs to the equalizer. An on-chip 50Ω terminating resistor connects D_IN0+ to VDD and D_IN0- to VDD. D_IN1− D_IN1+ 8 9 I, CML Inverting and non-inverting TMDS Data inputs to the equalizer. An on-chip 50Ω terminating resistor connects D_IN1+ to VDD and D_IN1- to VDD. D_IN2− D_IN2+ 11 12 I, CML Inverting and non-inverting TMDS Data inputs to the equalizer. An on-chip 50Ω terminating resistor connects D_IN2+ to VDD and D_IN2- to VDD. C_OUTC_OUT+ 36 35 O, CML Inverting and non-inverting TMDS outputs from the equalizer. Open collector. D_OUT0− D_OUT0+ 33 32 O, CML Inverting and non-inverting TMDS outputs from the equalizer. Open collector. D_OUT1– D_OUT1+ 29 28 O, CML Inverting and non-inverting TMDS outputs from the equalizer. Open collector. D_OUT2− D_OUT2+ 26 25 O, CML Inverting and non-inverting TMDS outputs from the equalizer. Open collector. 23 14 37 I, CMOS BST_0, BST_1, and BST_2 select the equalizer boost level for EQ channels. BST_0, BST_1, and BST_2 are internally pulled Low. EN 44 I, CMOS Enable Equalizer inputs. When held High, normal operation is selected. When held Low, standby mode is selected. EN is internally pulled High. FEB 21 I, CMOS Force External Boost. When held High, the equalizer boost setting is controlled by the BST_ [0:2] pins. When held Low, the equalizer boost level is controlled through the SMBus (see Table 1) control pins. FEB is internally pulled High. SD 45 O, CMOS Equalizer Clock Channel Signal Detect Output. Produces a High when signal is detected. VDD 3, 6, 7, 10, 13, 15, 46 I, Power VDD pins should be tied to the VDD plane through a low inductance path. A 0.01µF bypass capacitor should be connected between each VDD pin to the GND planes. GND 22, 24, 27, 30, 31, 34 I, Power Ground reference. GND should be tied to a solid ground plane through a low impedance path. PAD I, Power The exposed pad at the center of the package must be connected to the ground plane. Equalization Control BST_0 BST_1 BST_2 Device Control POWER Exposed Pad Serial Management Bus (SMBus) Interface Control Pins SDA SDC CS 18 17 16 I, CMOS I, CMOS I, CMOS Data Input. Internally pulled High. Clock Input. Internally pulled High. Chip select. When held High, the equalizer SMBus register is enabled. When held Low, the equalizer SMBus register is disabled. CS is internally pulled Low. CS is internally gated with SDC. Other Reserv 19, 20, 38, 39, 40,41, 42, 43, 47, 48 Reserved. Do not connect. Note: I = Input O = Output www.national.com 2 DS16EV5110 Connection Diagram 20216226 3 www.national.com DS16EV5110 Absolute Maximum Ratings (Note 1) ESD Rating If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. HBM, 1.5 kΩ, 100 pF CML Inputs Thermal Resistance θJA, No Airflow Supply Voltage (VDD) CMOS Input Voltage CMOS Output Voltage CML Input/Output Voltage Junction Temperature Storage Temperature Lead Temp. (Soldering, 5 sec.) −0.5V to +4.0V −0.5V + 4.0V −0.5V to 4.0V -0.5V to 4.0V +150°C −65°C to +150°C +260°C >8 kV >10 kV 30°C/W Recommended Operating Conditions (Notes 2, 3) Supply Voltage (VDD to GND) Ambient Temperature Min 3.0 Typ 3.3 −40 25 Max Units 3.6 V +85 °C Electrical Characteristics Over recommended operating supply and temperature ranges unless other specified. (Notes 2, 3) Symbol Parameter Conditions Min Typ Max Units —10 +10 μA 80 105 μA LVCMOS DC SPECIFICATIONS IIH-PU High Level Input Leakage Current CMOS pins with internal pull-up resistors IIH-PD High Level Input Leakage Current CMOS pins with internal pull-down resistors IIL-PU Low Level Input Leakage Current CMOS pins with internal pull-up resistors —20 —10 μA IIL-PD Low Level Input Leakage Current CMOS pins with internal pull-down resistors —10 +10 μA VIH High Level Input Voltage 2.0 VDD V VIL Low Level Input Voltage 0 0.8 V VOH High Level Output Voltage SD Pin VOL Low Level Output Voltage SD Pin Power Supply Consumption EN = High, Device Enabled 2.4 V 0.4 V 700 mW POWER P 475 EN = Low, Power Down Mode N 70 Supply Noise Tolerance (Note 4) 50 Hz – 100 Hz 100 Hz – 10 MHz 10 MHz – 825 MHz VIN Input Voltage Swing Measured differentially at TPA (Figure 1) VICMDC Input Common-Mode Voltage DC-Coupled Requirement Measured at TPB (Figure 1) RLI Differential Input Return Loss 100 MHz– 825 MHz, with fixture's effect de-embedded RIN Input Resistance IN+ to VDD and IN− to VDD 45 Measured differentially with OUT+ and OUT− terminated by 50Ω to VDD mW mVP-P mVP-P mVP-P 100 40 10 CML INPUTS 800 1200 mVP-P VDD-0.3 VDD-0.2 V 10 dB 55 Ω 800 1200 mVP-P VDD-0.3 VDD-0.2 V 75 240 ps 50 CML OUTPUTS VO Output Voltage Swing VOCM Output common-mode Voltage Measured Single-ended tR, tF Transition Time 20% to 80% of differential output voltage, measured within 1" from output pins. tCCSK www.national.com Inter Pair Channel-to-Channel Skew (all 4 Channels) Difference in 50% crossing between shortest and longest channels 4 25 ps tD Parameter Conditions Min Latency Typ Max 350 Units ps OUTPUT JITTER TJ1 TJ2 TJ3 TJ4 RJ Total Jitter at 1.65 Gbps Total Jitter at 2.25 Gbps Total Jitter at 165 MHz Total Jitter at 225 MHz 20m 28 AWG STP DVI Cable Data Paths EQ Setting 0x04 PRBS7 (Notes 5, 6, 7) 0.13 20m 28 AWG STP DVI Cable Data Paths EQ Setting 0x04 PRBS7 (Notes 5, 6, 7) 0.2 Clock Paths Clock Pattern (Notes 5, 6, 7) 0.17 UIP-P 0.165 Clock Paths Clock Pattern (Notes 5, 6, 7) UIP-P UIP-P 0.165 UIP-P 3 psrms Random Jitter (Notes 7, 8) FCLK Clock Frequency Clock Path (Note 5) 25 225 MHz BR Bit Rate Data Path (Note 5) 0.25 2.25 Gbps BIT RATE Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. Absolute Maximum Numbers are guaranteed for a junction temperature range of –40°C to +125°C. Models are validated to Maximum Operating Voltages only. Note 2: Typical values represent most likely parametric norms at VDD = 3.3V, TA = 25°C., and at the Recommended Operation Conditions at the time of product characterization and are not guaranteed. Note 3: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed. Note 4: Allowed supply noise (mVP-P sine wave) under typical conditions. Note 5: Specification is guaranteed by characterization and is not tested in production. Note 6: Deterministic jitter is measured at the differential outputs (TPC of Figure 1), minus the deterministic jitter before the test channel (TPA of Figure 1). Random jitter is removed through the use of averaging or similar means. Note 7: Total Jitter is defined as peak-to-peak deterministic jitter from (Note 8) + 14.2 times random jitter. Note 8: Random jitter contributed by the equalizer is defined as sq rt (JOUT2 − JIN2). JOUT is the random jitter at equalizer outputs in ps-rms, see TPC of Figure 1; JIN is the random jitter at the input of the equalizer in ps-rms, see TPA of Figure 1. 5 www.national.com DS16EV5110 Symbol DS16EV5110 Electrical Characteristics — Serial Management Bus Interface (Notes 2, 3) Over recommended operating supply and temperature ranges unless other specified. Symbol Parameter Conditions Min Typ Max Units 0.8 V VDD V Serial Bus Interface — DC Specifications VIL Data, Clock Input Low Voltage VIH Data, Clock Input High Voltage IPULLUP Current through pull-up resistor or VOL = 0.4V current source VDD Nominal Bus Voltage ILEAK-Bus Input Leakage per bus segment ILEAK-Pin Input Leakage per device pin CI Capacitance for SDA and SDC (Notes 9, 10) RTERM Termination Resistance VDD3.3 (Notes 9, 10, 11) 2000 Ω VDD2.5 (Notes 9, 10, 11) 1000 Ω 2.8 10 (Note 9) mA 3.0 3.6 V —200 +200 µA —15 µA 10 pF Serial Bus Interface Timing Specification FSMB Bus Operating Frequency TBUF Bus Free Time Between Stop and Start Condition THD:STA Hold Time After (Repeated) Start Condition. First CLK generated after this period. (Note 12) 10 100 kHz 4.7 µs 4.0 µs At IPULLUP, Max TSU:STA Repeated Start Condition Setup Time 4.7 µs TSU:STO Stop Condition Setup Time 4.0 µs THD:DAT Data Hold Time 300 ns TSU:DAT Data Setup Time 250 TTIMEOUT Detect Clock Low Timeout TLOW Clock Low Period THIGH Clock High Period (Note 12) TLOW:SEXT Cumulative Clock Low Extend Time (Slave Device) (Note 12) tF Clock/Data Fall Time tR Clock/Data Rise Time tPOR Time in which a device must be operational after power-on reset (Note 12) (Note 12) 25 ns 35 4.7 4.0 ms µs 50 µs 2 ms (Note 12) 300 ns (Note 12) 1000 ns 500 ms Note 9: Recommended value. Parameter not tested in production. Note 10: Recommended maximum capacitance load per bus segment is 400pF. Note 11: Maximum termination voltage should be identical to the device supply voltage. Note 12: Compliant to SMBus 2.0 physical layer specification. See System Management Bus (SMBus) Specification Version 2.0, section 3.1.1 SMBus common AC specifications for details. www.national.com 6 The Serial Management Bus interface is compatible to SMBus 2.0 physical layer specification, except for bus termination voltages. Holding the CS pin High enables the SMBus TABLE 1. SMBus Register Address Name Address Default Type Bit 7 Status 0x00 0x00 RO ID Revision Reserved Reserved Reserved SD Status 0x01 0x00 RO Reserved Boost 1 EN Status 0x02 0x00 RO Reserved Boost 3 Reserved Boost 2 Internal Enable/ Individual Channel Boost Control for C_IN±, D_IN0± 0x03 0x77 RW EN (Int.) 0:Enable 1:Disable (D_IN0±) Boost Control (BC for CH0) 000 (Min Boost) 001 010 011 100 101 110 111 (Max Boost) EN (Int.) Reserved 0:Enable 1:Disable (C_IN±) Individual Channel Boost Control for D_IN1±, D_IN2± 0x04 0x77 RW EN (Int.) 0:Enable 1:Disable (D_IN2±) Boost Control (BC for CH2) 000 (Min Boost) 001 010 011 100 101 110 111 (Max Boost) EN (Int.) 0:Enable 1:Disable (D_IN1±) Signal Detect ON (SD_ON) 0x05 0x00 RW Reserved Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reserved Boost Control (BC for CH1) 000 (Min Boost) 001 010 011 100 101 110 111 (Max Boost) Threshold (mV) 00: 70 (Default) 01: 55 10: 90 11: 75 Signal 0x06 Detect OFF (SD_OFF) 0x00 SMBus or 0x07 CMOS Control for EN 0x00 RW Reserved 0x08 0x78 RW Reserved Output Level Bit 6 RW Reserved Threshold (mV) 00: 40 (Default) 01: 30 10: 55 11: 45 SMBus Enable 0: Disable 1: Enable Output Level: 00: 540 mVp-p 01: 770 mVp-p 10: 1000 mVp-p 11: 1200 mVp-p Reserved Note: RO = Read Only, RW = Read/Write 7 www.national.com DS16EV5110 port allowing access to the SMBus registers. The configuration registers can be read and written using SMBus through the SDA and SDC pins. In the STANDBY state, the Serial Management Bus remains active. Please see Table 1 for more information. Serial Management Bus (SMBus) Configuration Registers DS16EV5110 20216227 FIGURE 1. Test Setup Diagram www.national.com 8 The DS16EV5110 video equalizer comprises three data channels, a clock channel, and a control interface including a Serial Management Bus (SMBus) port. DATA CHANNELS The DS16EV5110 provides three data channels. Each data channel consists of an equalizer stage, a limiting amplifier, a 20216237 FIGURE 2. DS16EV5110 Data Channel EQUALIZER BOOST CONTROL The data channel equalizers support eight programmable levels of equalization boost. The state of the FEB pin determines how the boost settings are controlled. If the FEB pin is held High, then the equalizer boost setting is controlled by the Boost Set pins (BST_[0:2]) in accordance with Table 2. If this programming method is chosen, then the boost setting selected on the Boost Set pins is applied to all three data channels. When the FEB pin is held Low, the equalizer boost level is controlled through the SMBus. This programming method is accessed via the appropriate SMBus registers (see Table 1). Using this approach, equalizer boost settings can be programmed for each channel individually. FEB is internally pulled High (default setting); therefore if left unconnected, the boost settings are controlled by the Boost Set pins (BST_[0:2]). The range of boost settings provided enables the DS16EV5110 to address a wide range of transmission line path loss scenarios, enabling support for a variety of data rates and formats. TABLE 2. EQ Boost Control Table Control Via SMBus BC_2, BC_1, BC_0 (FEB = 0) 9 Control Via Pins EQ Boost Setting BST_2, BST_1, at 825 MHz (dB) BST_0 (FEB = 1) 000 000 9 001 001 14 010 010 18 011 011 21 100 100 24 101 101 26 110 110 28 111 111 30 www.national.com DS16EV5110 DC offset correction block, and a TMDS driver as shown in Figure 2. DS16EV5110 Device Description DS16EV5110 CLOCK CHANNEL SIGNAL DETECT The DS16EV5110 features a signal detect circuit on the clock channel. The status of the clock signal can be determined by either reading the Signal Detect bit (SD) in the SMBus registers (see Table 1) or by the state of the SD pin. A logic High indicates the presence of a signal that has exceeded a specified maximum threshold value (called SD_ON). A logic Low means that the clock signal has fallen below a minimum threshold value (called SD_OFF). These values are programmed via the SMBus (Table 1). If not programmed via the SMBus, the minimum and maximum thresholds take on the default values for the minimum and maximum values as indicated in Table 4. The Signal Detect threshold values can be changed through the SMBus. All threshold values specified are DC peak-to-peak differential signals (positive signal minus negative signal) at the input of the device. DEVICE STATE AND ENABLE CONTROL The DS16EV5110 has an Enable feature which provides the ability to control device power consumption. This feature can be controlled either via the Enable Pin (EN Pin) or via the Enable Control Bit which is accessed through the SMBus port (see Table 1 and Table 3). If Enable is activated, the data channels and clock channel are placed in the ACTIVE state and all device blocks function as described. The DS16EV5110 can also be placed in STANDBY mode to save power. In this mode only the control interface including the SMBus port as well as the clock channel signal detection circuit remain active. TABLE 3. Enable and Device State Control Register 07[0] EN Pin Register 03[3] (SMBus) (CMOS) (EN Control) (SMBus) Device State TABLE 4. Clock Channel Signal Detect Threshold Values 0 : Disable 1 X ACTIVE 0 : Disable 0 X STANDBY 1 : Enable X 0 ACTIVE 0 0 40 (Default) 70 (Default) 1 : Enable X 1 STANDBY 0 1 30 55 1 0 55 90 1 1 45 75 Bit 1 Bit 0 Minimum Threshold Maximum Threshold Register 06 (mV) Register 05 (mV) CLOCK CHANNEL The clock channel incorporates a limiting amplifier, a DC offset correction, and a TMDS driver (Figure 3). 20216238 FIGURE 3. DS16EV5110 Clock Channel www.national.com 10 TABLE 5. Output Level Control Settings Bit 3 Bit 2 Output Level (mV) 0 0 540 0 1 770 1 0 1000 (default) 1 1 1200 AUTOMATIC ENABLE FEATURE It may be desired for the DS16EV5110 to be configured to automatically enter STANDBY mode if no clock signal is 11 www.national.com DS16EV5110 present. STANDBY mode can be implemented by connecting the Signal Detect (SD) pin to the external (CMOS) Enable (EN) pin. In order for this option to function properly, the FEB pin must be either tied High or not connected (the FEB pin is internally pulled High by default). If the clock signal applied to the clock channel input swings above the maximum level specified in the threshold register via the SMBus, then the SD pin is asserted High. If the SD pin is connected to the EN pin, this will enable the equalizer, limiting amplifier, and output buffer on the data channels and the limiting amplifier and output buffer on the clock channel (provided that the FEB pin is High); thus the DS16EV5110 will automatically enter the ACTIVE state. If the clock signal present falls below the minimum level specified in the threshold register, then the SD pin will be asserted Low, causing the aforementioned blocks to be placed in the STANDBY state. OUTPUT LEVEL CONTROL The output amplitude of the TMDS drivers for both the data channels and the clock channel can be controlled via the SMBus (see Table 1). The default output level is 1000mV p-p. The following Table presents the output level values supported: DS16EV5110 signal loss and degradation due to transmission through a length of shielded or unshielded cable. Application Information The DS16EV5110 is used to recondition DVI/HDMI video signals or differential signals with similar characteristics after 20216239 FIGURE 4. DS16EV5110 Typical Use high resolution for DVI applications (e.g., QXGA and WQXGA), a “dual link” TMDS interface is required. This is easily configured by using two DS16EV5110 devices as shown in Figure 5. DVI 1.0 AND HDMI V1.2a APPLICATIONS A single DS16EV5110 can be used to implement cable extension solutions with various resolutions and screen refresh rates. The range of digital serial rates supported is between 250 Mbps and 1.65 Gbps. For applications requiring ultra- 20216228 FIGURE 5. Connection in Dual Link Application ed termination resistors (50Ω), pulled up to VDD at the input stage, and open collector outputs for DVI / HDMI compliance. HDMI V1.3 APPLICATION The DS16EV5110 can reliably extend operation to distances greater than 20 meters of 28 AWG HDMI cable at 2.25 Gbps, thereby supporting HDMI v1.3 for 1080p HDTV resolution with 12-bit color depth. Please note that the Electrical Characteristics specified in this document have not been tested for and are not guaranteed for 2.25 Gbps operation. 28 AWG STP DVI / HDMI CABLES RECOMMENDED BOOST SETTINGS The following table presents the recommended boost control settings for various data rates and cable lengths for 28 AWG DVI/HDMI compliant configurations: DC COUPLED DATA PATHS AND DVI/HDMI COMPLIANCE The DS16EV5110 is designed to support TMDS differential pairs with DC coupled transmission lines. It contains integrat- www.national.com 12 Data Rate 28 AWG DVI / HDMI 0x04 750 Mbps 0–25m 0x04 1.65 Gbps 0–20m 0x06 750 Mbps 25m to greater than 30m 0x06 1.65 Gbps 20m to greater than 25m 0x03 2.25 Gbps 0–15m 0x06 2.25 Gbps 15m to greater than 20m General Recommendations UTP (UNSHIELDED TWIST PAIRS) CABLES The DS16EV5110 can be used to extend the length of UTP cables, such as Cat5, Cat5e and Cat6 to distances greater than 20 meters at 1.65 Gbps with < 0.13 UI of jitter. Please note that for non-standard DVI/HDMI cables, the user must ensure the clock-to-data channel skew requirements are met. Table 7 presents the recommended boost control settings for various data rates and cable lengths for UTP configurations: The DS16EV5110 is a high performance circuit capable of delivering excellent performance. Careful attention must be paid to the details associated with high-speed design as well as providing a clean power supply. Refer to the LVDS Owner’s Manual for more detailed information on high-speed design tips as well as many other available resources available addressing signal integrity design issues. POWER SUPPLY BYPASSING Two approaches are recommended to ensure that the DS16EV5110 is provided with an adequate power supply. First, the supply (VDD) and ground (GND) pins should be connected to power planes routed on adjacent layers of the printed circuit board. The layer thickness of the dielectric should be minimized so that the VDD and GND planes create a low inductance supply with distributed capacitance. Second, careful attention to supply bypassing through the proper use of bypass capacitors is required. A 0.01µF bypass capacitor should be connected to each VDD pin such that the capacitor is placed as close as possible to the DS16EV5110. Smaller body size capacitors can help facilitate proper component placement. Additionally, three capacitors with capacitance in the range of 2.2µF to 10µF should be incorporated in the power supply bypassing design as well. These capacitors can be either tantalum or an ultra-low ESR ceramic and should be placed as close as possible to the DS16EV5110. TABLE 7. Boost Control Setting for UTP Cables Setting Data Rate Cat5 Cable 0x03 750 Mbps 0–25m 0x06 750 Mbps 25–45m 0x03 1.65 Gbps Greater than 20m CABLE SELECTION At higher frequencies, longer cable lengths produce greater losses due to the skin effect. The quality of the cable with respect to conductor wire gauge and shielding heavily influences performance. Thicker conductors have lower signal degradation per unit length. In nearly all applications, the DS16EV5110 equalization can be set to 0x04, and equalize up to 22 dB skin effect loss for all input cable configurations at all data rates, without degrading signal integrity. PCB LAYOUT CONSIDERATIONS FOR DIFFERENTIAL PAIRS The TMDS differential inputs and outputs must have a controlled differential impedance of 100Ω. It is preferable to route 13 www.national.com DS16EV5110 TMDS lines exclusively on one layer of the board, particularly for the input traces. The use of vias should be avoided if possible. If vias must be used, they should be used sparingly and must be placed symmetrically for each side of a given differential pair. Route the TMDS signals away from other signals and noise sources on the printed circuit board. All traces of TMDS differential inputs and outputs must be equal in length to minimize intra-pair skew. See AN-1187 for additional information on LLP packages. TABLE 6. Boost Control Setting for STP Cables Setting DS16EV5110 Typical Performance Characteristics 20216229 20216230 FIGURE 6. Un-equalized vs. Equalized Signal after 25m of 28 AWG DVI Cable at 1.65 Gbps (0x06 Setting) 20216231 FIGURE 7. Output Signal after 20m of Cat5 Cable at 1.65 Gbps (0x06 Setting) 20216232 FIGURE 8. Output Signal after 30m of 28 AWG DVI Cable at 750 Mbps (0x06 Setting) www.national.com 14 DS16EV5110 20216233 FIGURE 9. Output Signal after 0.3m of 28 AWG DVI Cable at 1.65 Gbps (0x04 Setting) 20216234 FIGURE 10. Output Signal after 20m of 28 AWG HDMI Cable at 2.25 Gbps (0x06 Setting) 20216242 FIGURE 11. Equalized vs. Unequalized Jitter Performance Over 28 AWG DVI/HDMI Cable 15 www.national.com DS16EV5110 20216243 FIGURE 12. Equalized vs. Unequalized Jitter Performance Over Cat5 Cable Equivalent I/O Structures 20216240 FIGURE 13. Equivalent Output Structure 20216241 FIGURE 14. Equivalent Input Structure www.national.com 16 DS16EV5110 Physical Dimensions inches (millimeters) unless otherwise noted 7mm x 7mm 48-pin LLP Package Order Number DS16EV5110 Package Number SQA48D To order lead-free products, call your National Semiconductor distributors. They can order products for you with an "NOPB" specification. For more information on our Lead-free program, please check out our Lead-Free Status page. 17 www.national.com DS16EV5110 Video Equalizer for DVI, HDMI, and Cat5 Cables Notes THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2007 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560