LM3370 Dual Synchronous Step-Down DC-DC Converter with Dynamic Voltage Scaling Function General Description Features The LM3370 is a dual step-down DC-DC converter optimized for powering ultra-low voltage circuits from a single Li-Ion battery and input rail ranging from 2.7V to 5.5V. It provides two outputs with 600 mA load per channel. The output voltage range varies from 1V to 3.3V and can be dynamically controlled using the I2C compatible interface. This dynamic voltage scaling function allows processors to achieve maximum performance at the lowest power level. The I2C compatible interface can also be used to control auto PFM-PWM/PWM mode selection and other performance enhancing features. The LM3370 offers superior features and performance for portable systems with complex power management requirements. Automatic intelligent switching between PWM lownoise and PFM low-current mode offers improved system efficiency. Internal synchronous rectification enhances the converter efficiency without the use of further external devices. There is a power-on-reset function that monitors the level of the output voltage to avoid unexpected power losses. The independent enable pin for each output allows for simple and effective power sequencing. LM3370 is available in a 4 mm by 5 mm 16-lead non-pullback LLP and a 20-Bump micro SMD, 3.0 mm x 2.0 mm x 0.6 mm, package. A high switching frequency—2 MHz (typ)—allows use of tiny surface-mount components including a 2.2 µH inductor. Default fixed voltages for the 2 output voltages combination can be customized to fit system requirements by contacting National Semiconductor Corporation. ■ I2C compatible interface ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ — VOUT1 = 1V to 2V in 50 mV steps — VOUT2 = 1.8V to 3.3V in 100 mV steps — Automatic PFM/PWM mode switching & Forced PWM mode for low noise operation — Spread Spectrum capability using I2C 600 mA load per channel 2 MHz PWM fixed switching frequency (typ.) Internal synchronous rectification for high efficiency Internal soft start Power-on-reset function for both outputs 2.7V ≤ VIN ≤ 5.5V Operates from a single Li-Ion cell or 3 cell NiMH/NiCd batteries and 3.3V/5.5V fixed rails 2.2 µH Inductor, 4.7 µF Input and 10 µF Output Capacitor per channel 16-lead LLP Package (4 mm x 5 mm x 0.8 mm) 20-Bump micro SMD Package (3.0 mm x 2.0 mm x 0.6 mm) Applications ■ ■ ■ ■ Baseband Processors Application Processors (Video, Audio) I/O Power FPGA Power and CPLD Typical Performance Curve 20167379 Dimensions: 3.0 mm x 2.0 mm x 0.60 mm 20167381 Efficiency vs. Output Current, VOUT1= 1.2V © 2008 National Semiconductor Corporation 201673 www.national.com LM3370 Dual Synchronous Step-Down DC-DC Converter with Dynamic Voltage Scaling Function January 4, 2008 LM3370 Typical Application 20167301 FIGURE 1. Typical Application Circuit Functional Block Diagram 20167302 FIGURE 2. Functional Diagram www.national.com 2 LM3370 Package Marking Information 16-Lead LLP Package 20167343 FIGURE 3. Top Marking 20167342 FIGURE 4. Top View Pin Descriptions (LLP) Pin # Name 1 VIN2 Power supply voltage input to PFET and NFET switches for Buck 2 Description 2 SW2 Buck 2 Switch Pin 3 PGND2 4 VDD Buck 2 Power Ground Signal supply voltage input, VDD must be equal or greater of the two inputs (VIN1 & VIN2) 5 SGND Signal GND 6 PGND1 Buck 1 Power Ground 7 SW1 Buck 1 Switch Pin 8 VIN1 Power supply voltage input to PFET and NFET switches for Buck 1 9 FB1 Analog Feedback Input for Buck 1 10 SDA I2C Compatible Data, a 2 kΩ pull up resistor is required 11 SCL I2C Compatible Clock, a 2 kΩ pull up resistor is required 12 nPOR1 Power ON Reset for Buck 1, Open drain output Low when Buck 1 output is 92% of target output. A 100 kΩ pull up resistor is required 13 nPOR2 Power ON Reset for Buck 2, Open drain output Low when Buck 2 output is 92% of target output. A 100 kΩ pull up resistor is required 14 EN1 Buck 1 Enable 15 EN2 Buck 2 Enable 16 FB2 Analog feedback for Buck 2 3 www.national.com LM3370 Package Marking Information (micro SMD) micro SMD Marking 20167379 Top View XY = Date Code TT = Die Run Traceability S = Switcher Family PSB = LM3370TL-3013 20167377 Top View 20167378 Bottom View Pin Descriptions (micro SMD) Pin # Name A1 SW1 Buck 1 Switch Pin Description A2 VIN1 Power supply voltage input to PFET and NFET switches for Buck 1 A3 SGND A4 FB1 B1 PGND1 B2 PGND1_S B3 SDA I2C Compatible Data, a 2 kΩ pull up resistor is required B4 SCL I2C Compatible Clock, a 2 kΩ pull up resistor is required C1 VDD Signal supply voltage input, VDD must be equal or greater of the two inputs ( VIN1 & VIN2) Signal GND Analog Feedback Input for Buck 1 Buck 1 Power Ground Buck 1 Power Ground Sense C2 SGND Signal GND C3 nPOR1 Power ON Reset for Buck 1, Open drain output Low when Buck 1 output is 92% of target output. A 100 kΩ pull up resistor is required C4 nPOR2 Power ON Reset for Buck 2, Open drain output Low when Buck 2 output is 92% of target output. A 100 kΩ pull up resistor is required D1 PGND2 Buck 2 Power Ground D2 PGND2_S D3 EN2 Buck 2 Enable D4 EN1 Buck 1 Enable E1 SW2 Buck 2 Switch Pin E2 VIN2 Power supply voltage input to PFET and NFET switches for Buck 2 E3 SGND E4 FB2 www.national.com Buck 2 Power Ground Sense Signal GND Analog feedback for Buck 2 4 LM3370 I2C Controlled Features Features Parameter Comments Output Voltage VOUT1 & VOUT2 Output voltage is controlled via I2C compatible Modes Buck 1 & Buck 2 Mode can be controlled via I2C compatible by either forcing device in Auto mode or forced PWM mode Spread Spectrum Buck 1 & Buck 2 Spread Spectrum capability via I2C compatible for noise reduction Ordering Information (LLP) Order Number Voltage Option Package Marking Supplied As LM3370SD-3013 1.2V & 2.5V S0003UB 1000 units, Tape-and-Reel LM3370SDX-3013 LM3370SD-3021 1.2V & 3.3V LM3370SDX-3021 LM3370SD-3416 1.4V & 2.8V LM3370SDX-3416 LM3370SD-3621 1.5V & 3.3V LM3370SDX-3621 LM3370SD-3806 1.6V & 1.8V LM3370SDX-3806 LM3370SD-4221 1.8V & 3.3V LM3370SDX-4221 S0003UB 4500 units, Tape and Reel S0003TB 1000 units, Tape-and-Reel S0003TB 4500 units, Tape-and-Reel S0003VB 1000 units, Tape-and-Reel S0003VB 4500 units, Tape-and-Reel S0004AB 1000 units, Tape-and-Reel S0004AB 4500 units, Tape-and-Reel S0003XB 1000 units, Tape-and-Reel S0003XB 4500 units, Tape-and-Reel S0003YB 1000 units, Tape-and-Reel S0003YB 4500 units, Tape-and-Reel (micro SMD) Order Number Voltage Option Package Marking Supplied As LM3370TL-3607 NOPB 1.5V & 1.9V SPSB 1000 units, Tape-and-Reel SPSB 3000 units, Tape-and-Reel 1.2V & 2.0V SPTB 1000 units, Tape-and-Reel SPTB 3000 units, Tape-and-Reel 1.2V & 1.8V SPUB 1000 units, Tape-and-Reel SPUB 3000 units, Tape-and-Reel SPVB 1000 units, Tape-and-Reel SPVB 3000 units, Tape-and-Reel SPXB 1000 units, Tape-and-Reel SPXB 3000 units, Tape-and-Reel STHB 1000 units, Tape-and-Reel STHB 3000 units, Tape-and-Reel LM3370TLX-3607 NOPB LM3370TL-3008 NOPB LM3370TLX-3008 NOPB LM3370TL-3006 NOPB LM3370TLX-3006 NOPB LM3370TL-3806 NOPB 1.6V & 1.8V LM3370TLX-3806 NOPB LM3370TL-3206 NOPB 1.3V & 1.8V LM3370TLX-3206 NOPB LM3370TL-3022 NOPB 1.2V & 1.85V LM3370TLX-3022 NOPB Note the LM3370TL-3607 has the following default output voltages where VOUT1 = 1.5V & VOUT2 = 1.9V 5 www.national.com LM3370 ESD Ratings (Note 5) All Pins Absolute Maximum Ratings (Notes 1, 2) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. 2 kV HBM 200V MM Operating Ratings VIN1 , VIN2 VDD to PGND & SGND −0.2V to 6V PGND to SGND -0.2V to +0.2V SDA, SCL, EN, EN2, nPOR1, nPOR2, SW1, SW2, FB1 & FB2 (GND - 0.2) to (VIN + 0.2V) Maximum Continuous Power Dissipation (PD_MAX) (Note 3) Internally Limited Junction Temperature (TJ-MAX) 125°C Storage Temperature Range −65°C to +150°C Maximum Lead Temperature (Soldering) (Note 4) (Notes 1, 2) Input Voltage Range ((Note 10)) 2.7V to 5.5V Recommended Load Current Per 0 mA to 600 mA Channel Junction Temperature (TJ) Range −30°C to +125°C Ambient Temperature (TA) Range (Note −30°C to +85°C 6) Thermal Properties (Note 7) Junction-to-Ambient Thermal Resistance θJA (LLP-16) 26°C/W θJA (20-Bump micro SMD) 50°C/W Electrical Characteristics (Notes 2, 8, 10)Typical limits appearing in normal type apply for TJ = 25°C. Limits appearing in boldface type apply over the entire junction temperature range (TA = TJ = −30°C to +85°C). Unless otherwise noted, VIN1 = VIN2 = 3.6V. Symbol Parameter Conditions VFB Feedback Voltage (Note 11) VOUT Line Regulation Min Typ -3.5 Max +3.5 Units % 2.7V ≤ VIN ≤ 5.5V IO = 10 mA, VOUT = 1.8V 0.031 %/V Load Regulation 100 mA ≤ IO ≤ 600 mA VIN = 3.6V, VOUT = 1.8V 0.0013 %/mA IQ PFM Quiescent Current “On” PFM Mode, Both Bucks ON 34 µA IQ SD Quiescent Current “Off” EN1 = EN2 = 0V ILIM Peak Switching Current Limit VIN = 3.6V RDS_ON (LLP) PFET NFET RDS_ON PFET (micro SMD) NFET FOSC Internal Oscillator Frequency IEN Enable (EN) Input Current VIL Enable Logic Low VIH Enable Logic High 0.2 3 µA 1200 1400 mA VIN = 3.6V, ISW = 200 mA 390 500 VIN = 3.6V, ISW = 200 mA 240 350 VIN = 3.6V, ISW = 200 mA 350 400 VIN = 3.6V, ISW = 200 mA 170 210 2.0 2.4 MHz 0.01 1 µA 0.4 V 850 1.5 mΩ mΩ V 1.0 POWER ON RESET THRESHOLD/FUNCTION (POR) nPOR1 & nPOR2 Delay Time nPOR1 = Power ON Reset for Buck 1 nPOR2 = Power ON Reset for Buck 2 50 mS (default) POR Threshold Percentage of Target VOUT VOUT Rising 94 VOUT Falling, 85% (default), Can be pre-trimmed to 70% or 94% 85 www.national.com Can be pre-trimmd to 50 uS, 100 mS & 200 mS 6 50 mS % Note 2: All voltages are with respect to the potential at the GND pin. Note 3: Internal thermal shutdown circuitry protects the device from permanent damage. The thermal shutdown engages at TJ = 150°C (typ.) and disengages at TJ = 140°C(typ.). Note 4: For detailed soldering specifications and information, please refer to National Semiconductor Application Note 1187: Leadless Leadframe Package (LLP) (AN-1187). Note 5: The Human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. (MIL-STD-883 3015.7) The machine model is a 200 pF capacitor discharged directly into each pin. (EAIJ) Note 6: In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP = 125ºC), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to-ambient thermal resistance of the part/package in the application (θJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (θJA × PD-MAX). Note 7: Junction-to-ambient thermal resistance (θJA) is taken from a thermal modeling result, performed under the conditions and guidelines set forth in the JEDEC standard JESD51-7. The test board is a 4-layer FR-4 board measuring 102 mm x 76 mm x 1.6 mm with a 2 x 1 array of thermal vias. Thickness of copper layers are 2/1/1/2oz. Junction-to-ambient thermal resistance is highly application and board-layout dependent. In applications where high maximum power dissipation exists, special care must be paid to thermal dissipation issues in board design. The value of θJA of this product can vary significantly, depending on PCB material, layout, and environmental conditions. In applications where high maximum power dissipation exists (high VIN, high IOUT), special care must be paid to thermal dissipation issues. For more information on these topics, please refer to Application Note 1187: Leadless Leadframe Package (LLP) and the Power Efficiency and Power Dissipation section of this datasheet. Note 8: Min. and Max are guaranteed by design, test and/or statistical analysis. All electrical characteristics having room-temperature limits are tested during production with TJ = 25°C. All hot and cold limits are guaranteed by correlating the electrical characteristics to process and temperature variations and applying statistical process control. Note 9: Guaranteed by design. Note 10: Input voltage range for all voltage options is 2.7V to 5.5V. The voltage range recommended for the specified output voltages: VIN = 2.7V to 5.5V for 1V ≤ VOUT ≤ 1.7V and for VOUT = 1.8V or greater, VIN = VOUT + 1V or VIN,MIN = ILOAD * (RDSON_PFET + RDCR_INDUCTOR) + VOUT Note 11: Test condition: for VOUT less than 2.5V, VIN = 3.6V; for VOUT greater than or equal to 2.5V, VIN = VOUT + 1V. Dissipation Rating Table θJA TA = 60°C Power Rating 26°C/W (4-Layer Board) LLP-16 TA = 85°C Power Rating 1538 mW 50°C/W (4-Layer Board) 20-bump micro SMD 1300 mW 7 800 mW www.national.com LM3370 Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. LM3370 Typical Performance Characteristics LM3370SD/TL, Circuit of Figure 1, VIN = 3.6V, VOUT1 = 1.5V & VOUT2 = 2.5V, L = 2,2 µH (NR3015T2R2M), CIN = 4.7 µF (0805) and COUT = 10 µF (0805) & TA = 25°C, unless otherwise noted. IQ_PFM (Non Switching) Both Channels IQ_PWM (Non Switching) Both Channels 20167358 20167357 IQ_PWM (Switching) Both Channels IQ_SD (EN1 = EN2 = 0V) 20167349 20167359 RDS_ON (PFET) vs. Temperature VIN = 3.6V RDS_ON (NFET) vs. Temperature VIN = 3.6V 20167347 20167346 www.national.com 8 LM3370 RDS_ON (LLP) vs. VIN Current Limit vs. VIN 20167348 20167353 Switching Frequency vs. VIN Output Voltage vs. Output Current VIN = 3.6V (Forced PWM) 20167360 20167370 Efficiency vs. Output Current Forced PWM Mode, VOUT1 = 1.2V Efficiency vs. Output Current Forced PWM Mode, VOUT1 = 1.8V 20167362 20167363 9 www.national.com LM3370 Efficiency vs. Output Current Auto Mode, VOUT1 = 1.5V Efficiency vs. Output Current Auto Mode, VOUT2 = 1.9V 20167380 20167381 Efficiency vs. Output Current Auto Mode, VOUT2 = 3.3V Efficiency vs. Output Current Forced PWM Mode, VOUT2 = 3.3V 20167367 20167366 Typical Operation Waveform VIN = 3.6V, VOUT1 = 1.8V & VOUT2 = 1.8V Load = 400 mA Typical Operation Waveform VIN = 4.8V, VOUT1 = 1V & VOUT2 = 3.3V Load = 400 mA 20167321 20167320 www.national.com 10 LM3370 Typical Operation Waveform VIN = 3.6V, VOUT1 = 1.5V, VOUT2 = 2.5V, Load = 600 mA Each Start-up at PWM for BUCK1 ( VIN = 3.6V, VOUT = 1.5V, Load = 200 mA ) 20167327 20167322 Start-up at PWM for BUCK2 ( VIN = 3.6V, VOUT = 2.5V, Load = 200 mA ) Line Transient ( VOUT1 = 1.2V ) 20167330 20167325 Line Transient ( VOUT2 = 1.8V ) Load Transient in PFM MODE ( VOUT1 = 1.5V ) 20167331 20167332 11 www.national.com LM3370 Load Transient in PFM MODE ( VOUT1 = 1.5V ) Load Transient in PFM MODE ( VOUT1 = 1.8V ) 20167333 20167334 Load Transient in PFM MODE ( VOUT1 = 1.8V ) Load Transient in PWM MODE ( VIN = 3.6V, VOUT1 = 1.2V ) 20167335 20167338 Load Transient in PWM MODE ( VIN = 3.6V, VOUT1 = 1.5V ) Load Transient in PWM MODE ( VIN = 3.6V, VOUT2 = 2.5V ) 20167339 www.national.com 20167341 12 LM3370 Spread Spectrum Enabling ( VOUT Signal at 2 MHz) VOUT Stepping ( From 1.8V to 3.3V ) 20167371 20167375 VOUT Stepping ( From 3.3V to 1.8V ) 20167372 13 www.national.com LM3370 CURRENT LIMITING A current limit feature allows the LM3370 to protect itself and external components during overload conditions. PWM mode implements cycle-by-cycle current limiting using an internal comparator that trips at 1200 mA (typ.). If the outputs are shorted to ground the device enters a timed current limit mode where the NFET is turned on for a longer duration until the inductor current falls below a low threshold, ensuring inductor has more time to decay, thereby preventing runaway. Operation Description DEVICE INFORMATION The LM3370, a dual high efficiency step down DC-DC converter, delivers regulated voltages from input rails between 2.7V to 5.5V. Using voltage mode architecture with synchronous rectification, the LM3370 has the ability to deliver up to 600 mA per channel. The performance is optimized for systems where efficiency and space are critical. There are three modes of operation depending on the current required—PWM, PFM, and shutdown. PWM mode handles loads of approximately 70 mA or higher with 90% efficiency or better. Lighter loads cause the device to automatically switch into PFM mode to maintain high efficiency with low supply current (IQ = 20 µA typ.) per channel. The LM3370 can operate up to a 100% duty cycle (PFET switch always on) for low drop out control of the output voltage. In this way the output voltage will be controlled down to the lowest possible input voltage. Additional features include soft-start, under voltage lock out, current overload protection, and thermal overload protection. PFM OPERATION At very light loads, the converter enters PFM mode and operates with reduced switching frequency and supply current to maintain high efficiency. The part will automatically transition into PFM mode when either of two conditions are true, for a duration of 32 or more clock cycles: 1. The NFET current reaches zero. 2. The peak PFET switch current drops below the IMODE level . CIRCUIT OPERATION During the first portion of each switching cycle, the control block in the LM3370 turns on the internal PFET switch. This allows current to flow from the input through the inductor to the output filter capacitor and load. The inductor limits the current to a ramp with a slope of Supply current during this PFM mode is less than 20 µA per channel, which allows the part to achieve high efficiency under extremely light load conditions. When the output drops below the ‘low’ PFM threshold, the cycle repeats to restore the output voltage to ∼1.2% above the nominal PWM output voltage. If the load current should increase during PFM mode (see Figure 5) causing the output voltage to fall below the ‘low2’ PFM threshold, the part will automatically transition into fixedfrequency PWM mode. During PFM operation, the converter positions the output voltage slightly higher than the nominal output voltage during PWM operation, allowing additional headroom for voltage drop during a load transient from light to heavy load. The PFM comparators sense the output voltage via the feedback pin and control the switching of the output FETs such that the output voltage ramps between 0.8% and 1.6% (typical) above the nominal PWM output voltage. If the output voltage is below the ‘high’ PFM comparator threshold, the PFET power switch is turned on. It remains on until the output voltage exceeds the ‘high’ PFM threshold or the peak current exceeds the I PFM level set for PFM mode. The typical peak current in PFM mode is: by storing energy in a magnetic field. During the second portion of each cycle, the controller turns the PFET switch off, blocking current flow from the input, and then turns the NFET synchronous rectifier on. The inductor draws current from ground through the NFET to the output filter capacitor and load, which ramps the inductor current down with a slope of The output filter stores charge when the inductor current is high, and releases it when low, smoothing the voltage across the load. PWM OPERATION During PWM operation the converter operates as a voltagemode controller with input voltage feed forward. This allows the converter to achieve excellent load and line regulation. The DC gain of the power stage is proportional to the input voltage. To eliminate this dependence, feed forward inversely proportional to the input voltage is introduced. IPFM = 115 mA + VIN/57Ω Once the PFET power switch is turned off, the NFET power switch is turned on until the inductor current ramps to zero. When the NFET zero-current condition is detected, the NFET power switch is turned off. If the output voltage is below the ‘high’ PFM comparator threshold (see Figure 5), the PFET switch is again turned on and the cycle is repeated until the output reaches the desired level. Once the output reaches the ‘high’ PFM threshold, the NFET switch is turned on briefly to ramp the inductor current to zero and then both output switches are turned off and the part enters an extremely low power mode. INTERNAL SYNCHRONOUS RECTIFICATION While in PWM mode, the LM3370 uses an internal NFET as a synchronous rectifier to reduce rectifier forward voltage drop and associated power loss. Synchronous rectification provides a significant improvement in efficiency whenever the output voltage is relatively low compared to the voltage drop across an ordinary rectifier diode. www.national.com 14 SOFT-START The LM3370 has a soft start circuit that limits in-rush current during start up. Soft start is activated only if EN goes from logic low to logic high after VIN reaches 2.7V. LDO - LOW DROP OUT OPERATION The LM3370 can operate at 100% duty cycle (no switching, PFET switch completely on) for low drop out support of the 20167303 FIGURE 5. Operation in PFM Mode and Transfer to PWM Mode 15 www.national.com LM3370 output voltage. In this way the output voltage will be controlled down to the lowest possible input voltage. The minimum input voltage needed to support the output voltage is VIN,MIN = ILOAD*(RDSON,PFET + RINDUCTOR) + VOUT • ILOAD load current • RDSON/PFET drain to source resistance of PFET switch in the triode region • RINDUCTOR inductor resistance FORCED PWM MODE The LM3370 auto mode can be bypassed by forcing the device to operate in PWM mode, this can be implemented through the I2C compatible interface, see Table 1. LM3370 I2C Compatible Interface Electrical Specifications Unless otherwise noted, VBATT = 2.7V to 5.5V. Typical values and limits appearing in normal type apply for TJ = 25°C. Limits appearing in boldface type apply over the entire junction temperature range for operation, −30°C to +125°C. (Notes 2, 8, 9) Symbol Parameter Conditions Min Typ Max Units 400 kHz FCLK Clock Frequency tBF Bus-Free Time between Start and Stop (Note 10) 1.3 µS tHOLD Hold Time Repeated Start Condition (Note 10) 0.6 µS tCLKLP CLK Low Period (Note 10) 1.3 µS tCLKHP CLK High Period (Note 10) 0.6 µS tSU Set Up Time Repeated Start Condition (Note 10) 0.6 µS tDATAHLD Data Hold Time (Note 10) 200 nS tCLKSU Data Set Up Time (Note 10) 200 nS TSU Set Up Time for Start Condition (Note 10) 0.6 µS TTRANS Maximum Pulse Width of Spikes that Must be Suppressed by the Input Filter of Both DATA & CLK signals. (Note 10) VDD_I2C I2C Logic High Level 50 1 nS VIN V I2C Compatible Interface according to the I2C bus specification. Maximum frequency is 400 kHz. In I2C compatible mode, the SCL pin is used for the I2C clock and the SDA pin is used for the I2C data. Both these signals need a pull-up resistor according to I2C specification. The values of the pull-up resistor are determined by the capacitance of the bus (typ. ∼1.8k). Signal timing specifications are I2C COMPATIBLE DATA VALIDITY The data on SDA line must be stable during the HIGH period of the clock signal (SCL). In other words, state of the data line can only be changed when CLK is LOW. 20167306 START and STOP bits. The I2C bus is considered to be busy after START condition and free after STOP condition. During data transmission, I2C master can generate repeated START conditions. First START and repeated START conditions are equivalent, function-wise. I2C COMPATIBLE START AND STOP CONDITIONS START and STOP bits classify the beginning and the end of the I2C session. START condition is defined as SDA signal transitioning from HIGH to LOW while SCL line is HIGH. STOP condition is defined as the SDA transitioning from LOW to HIGH while SCL is HIGH. The I2C master always generates 20167307 www.national.com 16 I2C Compatible Write Cycle 20167309 W = write (SDA = “0”) r = read (SDA = “1”) ack = acknowledge (SDA pulled down by either master or slave) rs = repeated startxx=36h However, if a READ function is to be accomplished, a WRITE function must precede the READ function, as shown in the read cycle waveform. I2C Compatible Read Cycle 20167310 17 www.national.com LM3370 acknowledge. A receiver which has been addressed must generate an acknowledge after each byte has been received. After the START condition, I2C master sends a chip address. This address is seven bits long followed by an eighth bit which is a data direction bit (R/W). For the eighth bit, a “0” indicates a WRITE and a “1” indicates a READ. The second byte selects the register to which the data will be written. The third byte contains data to write to the selected register. TRANSFERRING DATA Every byte put on the SDA line must be eight bits long, with the most significant bit (MSB) being transferred first. The number of bytes that can be transmitted per transfer is unrestricted. Each byte of data has to be followed by an acknowledge bit. The acknowledge related clock pulse is generated by the master. The transmitter releases the SDA line (HIGH) during the acknowledge clock pulse. The receiver must pull down the SDA line during the 9th clock pulse, signifying an LM3370 Device Register Information Register Information Register Name Location Type Function Control 00 R/W Control signal for Buck 1 and Buck 2 Buck 1 01 R/W Output setting & Mode selection for Buck 1 Buck 2 02 R/W Output setting & Mode selection for Buck 2 and POR disable I2C CHIP ADDRESS INFORMATION 20167308 REGISTER 00 20167311 www.national.com 18 LM3370 REGISTER 01 20167312 REGISTER 02 20167313 19 www.national.com LM3370 TABLE 1. Output Selection Table via I2C Programing Buck Output Voltage Selection Codes Data Code Buck_1 (V) 00000 NA NA 00001 NA 1.8 00010 NA 1.85 or 1.9* 00011 NA 2.0 00100 NA 2.1 00101 1.00 2.2 00110 1.05 2.3 00111 1.10 2.4 01000 1.15 2.5 01001 1.20 2.6 01010 1.25 2.7 01011 1.30 2.8 01100 1.35 2.9 01101 1.40 3.0 01110 1.45 3.1 01111 1.50 3.2 10000 1.55 3.3 10001 1.60 NA 10010 1.65 NA 10011 1.70 NA 10100 1.75 NA 10101 1.80 NA 10110 1.85 NA 10111 1.90 NA 11000 1.95 NA 11001 2.00 NA * Can be trimmed at the factory at 1.85V or 1.9V using the same trim code. www.national.com 20 Buck_2 (V) SETTING OUTPUT VOLTAGE VIA I2C Compatible The outputs of the LM3370 can be programmed through Buck 1 & Buck 2 registers via I2C. Buck 1 output voltage can be dynamically adjusted between 1V to 2V in 50 mV steps and Buck 2 output voltage can be adjusted between 1.8V to 3.3V in 100 mV steps. Finer adjustments to the output of Buck 2 can be achieved with the placement of a resistor betweeen VOUT2 and the FB2 pin. Typically by placing a 20KΩ resistor, R, between these nodes will result in the programmed Output Voltage increasing by approximately 45mV,ΔVTYP . A 2.2 µH inductor with a saturation current rating of at least 1400 mA is recommended for most applications. The inductor’s resistance should be less than around 0.2Ω for good efficiency. Table 2 lists suggested inductors and suppliers. For low-cost applications, an unshielded bobbin inductor is suggested. For noise critical applications, a toroidal or shielded-bobbin inductor should be used. A good practice is to lay out the board with overlapping footprints of both types for design flexibility. This allows substitution of a low-noise toroidal inductor, in the event that noise from low-cost bobbin models is unacceptable. Below are some suggested inductor manufacturers include but are not limited to: ΔVTYP= R × 500mV / 234KΩ Please refer to for programming the desire output voltage. If the I2C compatible feature is not used, the default output voltage will be the pre-trimmed voltage. For example, LM3370SD-3021 refers to 1.2V for Buck 1 and 3.3V for Buck 2. VDD Pin VDD is the power supply to the internal control circuit, if VDD pin is not tied to VIN during normal operating condition, VDD must be set equal or greater of the two inputs ( VIN1 or VIN2 ). An optional capacitor can be used for better noise immunity at VDD pin or when VDD is not tied to either VIN pins. Additionally, for reasons of noise suppression, it is advisable to tie the EN1/EN2 pins to VDD rather than VIN . SDA, SCL Pins When not using I2C the SDA and SCL pins should be tied directly to the VDD pin. Micro-Stepping: The Micro-Stepping feature minimizes output voltage overshoot/undershoot during large output transients. If Microstepping is enabled through I2C, the output voltage automatically ramps at 50 mV per step for Buck 1 and 100 mV per step for Buck 2. The steps are summarized as follow: Buck 1: 50 mV/step and 32 µs/step Buck 2: 100 mV/step and 32 µs/step For example if changing Buck 1 voltage from 1V to 1.8V yields 20 steps [(1.8 - 1)/ 0.05 = 20]. This translates to 640μs [(20 x 32 µs) = 640 µs] needed to reach the final target voltage. TABLE 2. Suggested Inductors and Suppliers Vendor Dimensions (mm) ISAT DO3314-222 Coilcraft 3.3 x 3.3 x 1.4 1.6A LPO3310-222 SD3114-2R2 Cooper 3.3 x 3.3 x 1.0 1.1A 3.1 x 3.1 x 1.4 1.48A NR3010T2R2M Taiyo Yuden 3.0 x 3.0 x 1.0 1.1A NR3015T2R2M 3.0 x 3.0 x 1.5 1.48A 2.6 x 2.8 x 1.0 1.0A VLF3010AT2R2M1R0 TDK INPUT CAPACITOR SELECTION A ceramic input capacitor of 4.7 μF, 6.3V is sufficient for most applications. A larger value may be used for improved input voltage filtering. The input filter capacitor supplies current to the PFET switch of the LM3370 in the first half of each cycle and reduces voltage ripple imposed on the input power source. A ceramic capacitor's low ESR provides the best noise filtering of the input voltage spikes due to this rapidly changing current. Select an input filter capacitor with a surge current rating sufficient for the power-up surge from the input power source. The power-up surge current is approximately the capacitor’s value (µF) times the voltage rise rate (V/µs). The input current ripple can be calculated as: INDUCTOR SELECTION There are two main considerations when choosing an inductor; the inductor should not saturate, and the inductor current ripple is small enough to achieve the desired output voltage ripple. There are two methods to choose the inductor current rating. method 1: The total current is the sum of the load and the inductor ripple current. This can be written as • • • • Model ILOAD load current VIN input voltage L inductor f switching frequency OUTPUT CAPACITOR SELECTION DC bias characteristics of ceramic capacitors must be considered when selecting case sizes like 0805 and 0603. DC 21 www.national.com LM3370 method 2: A more conservative approach is to choose an inductor that can handle the maximum current limit of 1400 mA. Given a peak-to-peak current ripple (IPP) the inductor needs to be at least Application Information LM3370 bias characteristics vary from manufacturer to manufacturer and dc bias curves should be requested from them as part of the capacitor selection process. The output filter capacitor smoothes out current flow from the inductor to the load, helps maintain a steady output voltage during transient load changes and reduces output voltage ripple. These capacitors must be selected with sufficient capacitance and sufficiently low ESR to perform these functions. The output ripple voltage can be calculated as: Voltage peak-to-peak ripple due to capacitance = VOUT) or 85% (falling VOUT) of the desire output. The inherent delay between the output (at 94% of VOUT) to the time at which the nPOR is enabled is about 50 ms. A pull up resistor of 100 kΩ at nPOR pin is required. Please refer to the electrical specification table for other timing options. The diagram below illustrates the timing response of the POR function. Voltage peak-to-peak ripple due to ESR = VPP-ESR = IPP*RESR Voltage peak-to-peak ripple, root mean squared = 20167319 SPREAD SPECTRUM (SS) The LM3370 features Spread Spectrum capability, via I2C, to reduce the noise amplitude of the switching frequency during data transmission. The feature can be enabled by activating the appropriate control register bit (see register information section for detail). The main clock of the LM3370 features spread spectrum at FOSC = 2 MHz ± 22 kHz ( peak frequency deviation) with the modulation frequency of either 1 kHz(default) or 2 kHz via I2C. This help reduce noise caused by the harmonics present in the waveforms at the switch pins of the buck regulators. It is controlled by I2C in the following manner: Note that the output ripple is dependent on the current ripple and the equivalent series resistance of the output capacitor (RESR). The RESR is frequency dependent (as well as temperature dependent); make sure that the frequency of the RESR given is the same order of magnitude as the switching frequency. TABLE 3. Suggested Capacitors and Their Suppliers Model Description Case Size Vendor 4.7 µF for CIN C1608X5R0J475 Ceramic, X5R, 6.3V Rating 0603 TDK C2012X5R0J475 Ceramic, X5R, 6.3V Rating 0805 JMK212BJ475 Ceramic, X5R, 6.3V Rating 0805 GRM21BR60J475 Ceramic, X5R, 6.3V Rating 0805 GRM219R60J475KE19D Ceramic, X5R, 6.3V Rating 0805 (Thin) <1mm Height C2012X5R0J106 Ceramic, X5R, 6.3V Rating 0805 TDK JMK212BJ106 Ceramic, X5R, 6.3V Rating 0805 Taiyo Yuden GRM21BR60J106 Ceramic, X5R, 6.3V Rating 0805 GRM219R60J106KE19D Ceramic, X5R, 6.3V Rating 0805 (Thin) < 1mm Height Modulation Frequency SS_fmod = 1 (default) 1 kHz SS_fmod = 0 2 kHz BOARD LAYOUT CONSIDERATIONS PC board layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance of a DCDC converter and surrounding circuitry by contributing to EMI, ground bounce, and resistive voltage loss in the traces. These can send erroneous signals to the DC-DC converter IC, resulting in poor regulation or instability. Good layout for the LM3370 can be implemented by following a few simple design rules: 1. Place the LM3370, inductor and filter capacitors close together and make the traces short. The traces between these components carry relatively high switching currents and act as antennas. Following this rule reduces radiated noise. Place the capacitors and inductor within 0.2 in. (5mm) of the LM3370. 2. Arrange the components so that the switching current loops curl in the same direction. During the first half of each cycle, current flows from the input filter capacitor, through the LM3370 and inductor to the output filter capacitor and back through ground, forming a current loop. In the second half of each cycle, current is pulled up from ground, through the LM3370 by the inductor, to the output filter capacitor and then back through ground, forming a second current loop. Routing these loops so the current curls in the same direction prevents magnetic field reversal between the two half-cycles and reduces radiated noise. 3. Connect the ground pins of the LM3370, and filter capacitors together using generous component-side Taiyo Yuden muRata 10µF COUT muRata POR (POWER ON RESET) The LM3370 has an independent POR functions (nPOR) for each buck converter. The nPOR1 and nPOR2 are open drain circuits which pull low when the outputs are below 94% (rising www.national.com I2C bit 22 Refer to the section "Surface Mount Technology (SMD) Assembly Considerations". For best results in assembly, alignment ordinals on the PC board should be used to facilitate placement of the device. The pad style used with Micro SMD package must be the NSMD (non-solder mask defined) type. This means that the solder-mask opening is larger than the pad size. This prevents a lip that otherwise forms if the soldermask and pad overlap, from holding the device off the surface of the board and interfering with mounting. See Application Note 1112 for specific instructions how to do this. The 20Bump package used for LM3370TL has 300 micron solder balls and requires 10.82 mils pads for mounting on the circuit board. The trace to each pad should enter the pad with a 90° entry angle to prevent debris from being caught in deep corners. Initially, the trace to each pad should be 7 mil wide, for a section approximately 7 mil long or longer, as a thermal relief. Then each trace should neck up or down to its optimal width. The important criteria is symmetry. This ensures the solder bumps on the LM3370TL re-flow evenly and that the device solders level to the board. In particular, special attention must be paid to the pads for bumps A2/B1 of VOUT1, and E2/D1 of VOUT2, because VIN and PGND are typically connected to large copper planes, inadequate thermal relief can result in late or inadequate re-flow of these bumps. The Micro SMD package is optimized for the smallest possible size in applications with red or infrared opaque cases. Because the Micro SMD package lacks the plastic encapsulation characteristic of larger devices, it is vulnerable to light. Backside metallization and/or epoxy coating, along with frontside shading by the printed circuit board, reduce this sensitivity. However, the package has exposed die edges. In particular, Micro SMD devices are sensitive to light, in the red and infrared range, shining on the package’s exposed die edges. Micro SMD PACKAGE ASSEMBLY AND USE Use of the Micro SMD package requires specialized board layout, precision mounting and careful re-flow techniques, as detailed in National Semiconductor Application Note 1112. 23 www.national.com LM3370 copper fill as a pseudo-ground plane. Then, connect this to the ground-plane (if one is used) with several vias. This reduces ground-plane noise by preventing the switching currents from circulating through the ground plane. It also reduces ground bounce at the LM3370 by giving it a lowimpedance ground connection. 4. Use wide traces between the power components and for power connections to the DC-DC converter circuit. This reduces voltage errors caused by resistive losses across the traces. 5. Route noise sensitive traces, such as the voltage feedback path, away from noisy traces between the power components. The voltage feedback trace must remain close to the LM3370 circuit and should be direct but should be routed opposite to noisy components. This reduces EMI radiated onto the DC-DC converter’s own voltage feedback trace. 6. Place noise sensitive circuitry, such as radio IF blocks, away from the DC-DC converter, CMOS digital blocks and other noisy circuitry. Interference with noisesensitive circuitry in the system can be reduced through distance. In mobile phones, for example, a common practice is to place the DC-DC converter on one corner of the board, arrange the CMOS digital circuitry around it (since this also generates noise), and then place sensitive preamplifiers and IF stages on the diagonally opposing corner. Often, the sensitive circuitry is shielded with a metal pan and power to it is postregulated to reduce conducted noise, using low-dropout linear regulators. LM3370 Physical Dimensions inches (millimeters) unless otherwise noted NOTES: UNLESS OTHERWISE SPECIFIED 1. For solder thickness and composition, see “Solder Information” in the packaging section of the National Semiconductor Web Page (www.national.com) 2. 3. Maximum allowable metal burn on lead tips at the package edges is 76 microns. No JEDEC registration as of December 2004. 16-Lead LLP Package NS Package Number SDA16B 4 mm x 5 mm x 0.75 mm www.national.com 24 LM3370 NOTE: UNLESS OTHERWISE SPECIFIED 1. EPOXY COATING 2. FOR SOLDER BUMP COMPOSITION, SEE “SOLDER INFORMATION” IN THE PACKAGE SECTION OF THE NATIONAL SEMICONDUCTOR WEB PAGE (www.national.com) 3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD. 4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION. 5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT. 6. REFERENCE JEDEC REGISTRATION MO-211, VARIATION DG. 20-Bump micro SMD Package, 0.5mm Pitch NS Package Number TLA20CWA X1 = 2.047 mm ± 0.030 mm X2 = 3.000 mm ± 0.030 mm X3 = 0.600 mm ± 0.075 mm 25 www.national.com LM3370 Dual Synchronous Step-Down DC-DC Converter with Dynamic Voltage Scaling Function Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: [email protected] German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: [email protected] National Semiconductor Japan Technical Support Center Email: [email protected]