FEBRUARY 2000 SC14404 Complete Baseband Processor for DECT Handsets General Description n n n n The SC14404 is a CMOS chip optimized to handle all the audio, signal and data processing needed within a DECT handset. An ADPCM transcoder, a very low power CODEC and Analog Frontend is integrated. Direct connections towards microphone and a (dynamical) loudspeaker are provided. Duplex quality handsfree operation is integrated. n n n n n n n n n n n The SC14404 is designed to fit to any radio design. A dedicated TDMA controller handles all physical layer slot formats and radio control. National Semiconductors standard CompactRISCTM CR16B 16 bit microcontroller takes care of all the higher protocol stack. 4 kilobyte F lash is integrated for parameter and number storage. n Features n Integrated DECT Baseband transceiver optimized for GAP handsets according to ETS 300 175-2, 175-3 & 175-8. n Two on board low drop voltage regulators with 2.85V and 3.0- 3.8V (with external resistors the voltage can be determined) output. n 2V upto 3.6V battery input with onboard step up converter. n n n n n 3V upto 5.0V battery monitor input. Advanced battery management unit Very low power in active and paging mode. Embedded 16 bit CompactRISCT M Micro Controller. (CR16B) with programmable clock speeds. 4k byte memory mapped Flash 320 kbyte Flash or factory programmed ROM FLASH. ACCESSBUSTM or MICROWIRE T M interfaces 5,5 kilobyte on-chip Data Memory. One full duplex ADPCM transcoder. On-chip 14-bit linear CODEC. 14 upto 44 dB gain differential microphone input buffer. 100 Ω loudspeaker driver. Software controlled gain on audio input and output. Peak hold ADC for RSSI measurement. Five general purpose inputs can be multiplexed on an 8 bit ADC with selectable ranges. On-chip dedicated TDMA instruction co-processor which supports 1.152 MHz, 0.576 MHz and 0.288 MHz bit rates. Seven programmable control signals for radio front end. Full and double slot, protected and unprotected Bfields. Duplex quality handsfree operation. Tone generator. Tones consisting of 3 frequencies can be programmed Linear PCM interface for external codec. ________________________________________________________________________________________________ System Diagram Note: ACCESSBUST M, MICROWIRET M and CompactRISCT M are trademarks of National Semiconductor Corporation. Copyright 2000 National Semiconductor Corp. 1 www.national.com SC14404 Complete Baseband Processor for DECT Handsets PRELIMINARY AD4 AD5 AD6 AD7 AD12 AD15 AD16 WRn AD17 AD14 AD13 AD8 AD9 AD11 RDn AD10 RCSn DAB7 DAB6 DAB5 VSS VDD DAB4 DAB3 DAB2 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 SC14404 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 DAB1 DAB0 AD0 AD1 AD2 AD3 RSTN AVS2 AVD2 LRS+ LRSVREFMICAGND MIC+ VREF+ VBAT1 VBAT2 DC_DIS VBAT3 DC_stab DC_I P2[6] DC_Sense LDO_Sense LDO2_CTRL LDO1_CTRL P0[0] P0[1] P0[2] P0[3] P0[4] P0[5] P0[6] P0[7] INT0n P1[0] INT1n P1[1] INT2n P1[2] INT3n P1[3] INT4n P1[4] INT5n P1[5] PON P1[6] CHARGE P1[7] VDD VSS PWM0 P2[0] PCM_DI PWM1 P2[1] ADC0 P2[2] PCM_D0 ADC1 P2[3] SCL P2[4] SDA P2[5] DC_CTRL P2[7] 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 AD18 PD7 PD1 PD5 PD4 PD3 PD2 VDD VSS RFCLK VDDRF DAC Xtal1 CAP AVS AVD RSSI RDI CMPREF TDO LE SO SK PCM_FSC/PD6/ADC3 PCM_CLK /DAC2/ADC2 UTX URX SC14404 Complete Baseband Processor for DECT Handsets 1.0 CONNECTION DIAGRAMS Order Number SC14404BFLAG (320kbyte Full FLASH, Boot mode A, 100 pins TQFP, Order Number SC14404BFLBG (320kbyte Full FLASH, Boot mode B, 100 pins TQFP Order Number SC14404BxxAG (320kbyte ROM FLASH, Boot mode A , 100 pins TQFP) Order Number SC14404BxxBG (320kbyte ROM FLASH, Boot mode B, 100 pins TQFP) See NS Package Number VJG100A Copyright 2000 National Semiconductor Corp. 2 www.national.com 1 2 3 4 5 6 7 8 9 10 A B C D E F G H J K Order Number SC14404BFLBC (320kbyte Full FLASH, Boot mode B, 100 pins CSP Order Number SC14404BxxBC (320kbyte ROM FLASH, Boot mode B, 100 pins CSP Table 1: Note 1: TQFP pin mapping onto CSP package (See table 2 for TQFP pin description) 1 2 3 4 5 6 7 8 9 10 A 1 99 96 93 89 88 86 85 83 76 B 8 2 98 95 92 90 87 80 77 74 C 10 5 3 97 94 84 82 78 73 71 D 11 12 7 6 100 79 81 72 70 68 E 13 15 9 4 16 91 75 69 67 64 F 14 17 19 25 41 66 54 59 65 63 G 18 20 22 31 29 50 56 57 62 61 H 21 23 28 32 34 44 47 53 55 60 J 24 27 30 37 40 42 45 48 52 58 K 26 33 35 36 38 39 43 46 49 51 All digital outputs can sink/source 2 mA unless otherwise specified. All digital inputs are Schmitt trigger types. After reset all I/Os are set to input and all pull-up or pull-down resistors are enabled unless otherwise specified. PU = Pull-up resistor enabled, PD = Pull-down resistor enabled, I = input A-I, B-I = In Boot mode A or B input and pull-up or pull-down resistor disabled, A-PD, B-PU = In Boot mode A, Pull-down resistor enabled. In Boot mode B, pull-up resistor enabled. Note 2: Reset state of address and data bus and WRn, RDn pins: If SC14404: Hi-Z/1 means Hi-Z if RSTn is LOW, if RSTn goes HIGH i t t akes 32 SCLK cycles = 25 usec before these pin drives a ‘1’. Copyright 2000 National Semiconductor Corp. 3 www.national.com SC14404 Complete Baseband Processor for DECT Handsets SC14404 CSP pin diagram (TOP View) SC14404 Complete Baseband Processor for DECT Handsets BLOCK DIAGRAM FIGURE 1. SC14404 Block diagram Copyright 2000 National Semiconductor Corp. 4 www.national.com SC14404 Complete Baseband Processor for DECT Handsets 2.0 Package information FIGURE 2. 100 pins TP Quad Flat Pack. NS Package Number VJG100A 0.1 N A1 BALL PAD CORNER M 1.4 +-0.1 A1 BALL PAD CORNER Note 3 (7.2 TYP) (1.4 TYP) 0.36 +- 0.05 TYP 0.8 TYP A B C D E F G H J K SEATING PLANE Note 3 10 +- 0.2 L 10 +- 0.2 10 9 8 7 6 5 4 3 2 1 0.46 TYP Note 2 Top view Bottom view 0.15 M N L S M S NOTES: UNLESS OTHERWISE SPECIFIED 0.08 M N 1. SOLDER BALL COMPOSITION: Sn 63%, Pb 37% 2. DIMENSIONS MEASURED AT MAXIMUM SOLDER BALL DIAMETER, PARALLEL TO PRIMARY DATUM N 3. PRIMARY DATUM N AND SEATING PLANE ARE DEFINED BY THE SPHERICAL CROWNS OF THE SOLDER BALLS 4. NO JEDEC REGISTRATION AS OF JUNE 1998 Dimensions are in milimeters FIGURE 3. 100 pins Chip Scaled Package. NS package SLC100A Copyright 2000 National Semiconductor Corp. 5 www.national.com SC14404 Complete Baseband Processor for DECT Handsets 3.0 Product status definitions Definition of Terms Data Sheet Identification Product Status Definition Advance Information Formative or In Design Preliminary First Production This data sheet contains the design specifications for product development. Specifications may change in any manner without notice. This data sheet contains preliminary data. Supplementary data will be published at a later date. National Semiconductor Corporation reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. No Identification Noted Full Production This data sheet contains final specifications. National Semiconductor Corporation reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Obsolete Not In Production This data sheet contains specifications on a product that has been discontinued by National Semiconductor Corporation. The datasheet is printed for reference information only. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: [email protected] Copyright 2000 National Semiconductor Corp. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Europe Fax: (+49) 0-180-530 85 86 Email: [email protected] Deutsch Tel: (+49) 0-180-530 85 85 English Tel: (+49) 0-180-532 78 32 6 National Semiconductor Asia Pacific Customer Response Group Tel: 65-254-4466 Fax: 65-250-4466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5620-6175 Fax: 81-3-5620-6179 www.national.com