ASW135 5-4000 MHz MMIC Amplifier Features Description ·16.5 dB Gain at 2000 MHz The ASW135, a power amplifier MMIC, has a high linearity, high gain, and high efficiency over a wide range of frequency, being suitable for use in both receiver and transmitter of telecommunication systems up to 4 GHz. The amplifier is available in an SOT-363 package and passes through the stringent DC, RF, and reliability tests. ·18.5 dBm P1dB at 2000 MHz ·29 dBm Output IP3 at 2000 MHz ·1.8 dB NF at 2000 MHz ·MTTF > 100 Years ·Single Supply Package Style: SOT-363 Package Style: SOT-363 Typical Performance Parameters Frequency Units Application Circuit Typical MHz 150 900 2000 2400 2700 Gain dB 19.6 18.5 16.5 15.7 15 ·500 ~ 3500 MHz S11 dB -10 -14 -14 -15 -16 ·IF ( 50 ~ 450 MHz ) S22 dB -15 -15 -15 -14 -13 Output IP31) dBm 27.5 28.5 29 31 32.5 Noise Figure dB 1.9 1.8 1.8 1.8 1.9 Output P1dB dBm 17.5 17.5 18.5 17 17 Current mA 60 60 60 60 60 V 3.3 3.3 3.3 3.3 3.3 Device Voltage (V) 1) OIP3 is measured with two tones at an output power of +5 dBm/tone separated by 1 MHz. Product Specifications Parameters Testing Frequency Units Min Typ MHz 2000 Gain dB 16.5 S11 dB -14 dB -15 dBm 29 S22 Output IP3 Noise Figure dB 1.8 Output P1dB dBm 18.5 Current mA 60 V 3.3 Device Voltage (V) Max Pin Configuration Absolute Maximum Ratings Parameters Rating Pin No. Function -40 to +150°C 1 RF OUT / Bias Device Voltage (V) +4.3 V 4 RF IN Operating Junction Temperature +150°C 2,3,5,6 GND Input RF Power (CW, 50 ohm matched)* 20 dBm Operating Case Temperature -40 to +85°C Storage Temperature * Please find the max. input power data from http://www.asb.co.kr/pdf/Maximum_Input_Power_Analysis.pdf 1/5 ASB Inc. · [email protected] · Tel: +82-42-528-7223 July 2011 ASW135 5-4000 MHz MMIC Amplifier Outline Drawing Symbols A A1 A2 b C D F E1 e e1 L Dimensions (In mm) MIN NOM MAX 0.90 1.00 1.10 0.025 0.062 0.10 0.875 0.937 1.00 0.20 0.30 0.40 0.10 0.125 0.15 1.90 2.00 2.10 1.15 1.25 1.35 2.00 2.10 2.20 -0.65BSC --1.30BSC --0.425REF -- Pin NO. Function Pin NO. Function. 1 RF OUT / Bias 4 RF IN 2 GND 5 GND 3 GND 6 GND Mounting Recommendation (in mm) Note: 1. The number and size of ground via holes in a circuit board is critical for thermal and RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of lead pin 2 for better RF and thermal performance, as shown in the drawing at the left side. ESD Classification & Moisture Sensitivity Level ESD Classification HBM Class 1A Voltage Level: 400 V MM Class A Voltage Level: 50 V CAUTION: ESD-sensitive device! Moisture Sensitivity Level (MSL) Level 3 at 260°C reflow 2/5 ASB Inc. · [email protected] · Tel: +82-42-528-7223 July 2011 ASW135 5-4000 MHz MMIC Amplifier APPLICATION CIRCUIT Frequency (MHz) 900 2000 2400 2700 Magnitude S21 (dB) 18.5 16.5 15.7 15 Magnitude S11 (dB) -14 -14 -15 -16 Magnitude S22 (dB) -15 -15 -14 -13 Output P1dB (dBm) 17.5 18.5 17 17 500 ~ 3500 MHz Output IP31) (dBm) 28.5 29 31 32.5 +3.3 V Noise Figure (dB) 1.8 1.8 1.8 1.9 Device Voltage (V) 3.3 3.3 3.3 3.3 Current (mA) 60 60 60 60 1) OIP3 is measured with two tones at an output power of +5 dBm/tone separated by 1MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vs=3.3 V C4=1 mF C3=100 pF C1=56 pF RF IN L1=33 nH ASW135 C2=56 pF RF OUT L2=33 nH 25 0 20 -5 15 -10 S11 (dB) Gain (dB) S-parameters & K-factor 10 5 0 -15 -20 0 500 1000 1500 2000 2500 3000 3500 -25 0 500 1000 Frequency (MHz) 5 -5 4 Stability Factor 0 S22 (dB) -10 -15 -20 -25 2000 2500 3000 3500 2500 3000 3500 3 2 1 0 500 1000 1500 2000 2500 3000 3500 0 0 500 Frequency (MHz) 3/5 1500 Frequency (MHz) 1000 1500 2000 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 July 2011 ASW135 5-4000 MHz MMIC Amplifier Frequency (MHz) 70 150 300 450 20.5 19.6 19.2 19 Magnitude S11 (dB) -6 -10 -12 -12 Magnitude S22 (dB) -15 -15 -17 -18 Output P1dB (dBm) 17 17.5 17.5 17.5 Output IP31) (dBm) 27.5 27.5 28.5 28.5 Noise Figure (dB) 2.1 1.9 1.8 1.7 Device Voltage (V) 3.3 3.3 3.3 3.3 Current (mA) 60 60 60 60 Magnitude S21 (dB) APPLICATION CIRCUIT IF 50 ~ 450 MHz +3.3 V 1) OIP3 is measured with two tones at an output power of +5 dBm/tone separated by 1MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vs=3.3 V C4=1 mF C3=100 pF C1=10 nF RF IN L1=180 nH ASW135 C2=100 pF RF OUT L2=180 nH S-parameters & K-factor 25 0 20 15 S11 (dB) Gain (dB) -5 10 -10 -15 5 0 0 100 200 300 400 500 -20 0 100 200 Frequency (MHz) 5 -5 4 Stability Factor 0 S22 (dB) -10 -15 -20 -25 400 500 3 2 1 0 100 200 300 400 500 0 0 500 Frequency (MHz) 4/5 300 Frequency (MHz) 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 July 2011 ASW135 5-4000 MHz MMIC Amplifier APPLICATION CIRCUIT SMATV 950 ~ 2150 MHz +3.3 V Frequency (MHz) 950 1600 2150 Magnitude S21 (dB) 18 17.3 16 Magnitude S11 (dB) -8 -13 -17 Magnitude S22 (dB) -9 -14 -12 Output P1dB (dBm) 16 18 18 Output IP31) (dBm) 32 32 32 Noise Figure (dB) 2.7 2.2 2.4 Device Voltage (V) 3.3 3.3 3.3 Current (mA) 60 60 60 1) OIP3 is measured with two tones at an output power of +5 dBm/tone separated by 1MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic 25 0 20 -5 15 -10 S11 (dB) Gain (dB) S-parameters & K-factor 10 5 0 -15 -20 0 500 1000 1500 2000 2500 3000 3500 -25 0 500 1000 Frequency (MHz) 5 -5 4 Stability Factor 0 S22 (dB) -10 -15 2500 3000 3500 2500 3000 3500 3 2 0 0 500 1000 1500 2000 2500 3000 3500 0 500 Frequency (MHz) 5/5 2000 1 -20 -25 1500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 1000 1500 2000 Frequency (MHz) July 2011