ASW101 5-3000 MHz MMIC Amplifier Features Description ·18 dB Gain at 900 MHz The ASW101, a power amplifier MMIC, has a high linearity, high gain, and high efficiency over a wide range of frequency, being suitable for use in both receiver and transmitter of telecommunication systems up to 3 GHz. The amplifier is available in an SOT-89 package and passes through the stringent DC, RF, and reliability tests. ·17 dBm P1dB at 900 MHz ·30 dBm Output IP3 at 900 MHz ·3.8 dB NF at 900 MHz ·MTTF > 100 Years ·Single Supply ASW101 Package Style: SOT-89 Typical Performance Parameters Frequency Units Application Circuit Typical MHz 900 2000 Gain dB 18 11 ·IF ·IF (Low Current) S11 dB -10 -10 ·500 ~ 2500 MHz S22 dB -18 -18 Output IP31) dBm 30 31 Noise Figure dB 3.8 4.0 Output P1dB dBm 17 18 Current mA 40 40 V 3.3 3.3 Device Voltage 1) OIP3 is measured with two tones at an output power of +3 dBm/tone separated by 1 MHz. Product Specifications Parameters Testing Frequency Units Gain dB S11 dB S22 Min MHz 17 dBm dB Output P1dB dBm 16 Current mA 35 V 18 -18 29 Noise Figure Device Voltage Max -10 dB Output IP3 Typ 900 30 3.8 4.5 17 40 45 3.3 Pin Configuration Absolute Maximum Ratings Parameters Rating Operating Case Temperature -40 to +85°C Storage Temperature -40 to +150°C Device Voltage +6 V Operating Junction Temperature +150°C Pin No. Function Input RF Power (CW, 50ohm matched)* 25 dBm 1 RF IN 2 GND 3 RF OUT / Bias * Please find the max. input power data from http://www.asb.co.kr/pdf/Maximum_Input_Power_Analysis.pdf 1/6 ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2010 ASW101 5-3000 MHz MMIC Amplifier Outline Drawing Part No. Lot No. Symbols A L b b1 C D D1 E E1 e1 H S e ASW101 Pxxxx Dimensions (In mm) MIN NOM MAX 1.40 1.50 1.60 0.89 1.04 1.20 0.36 0.42 0.48 0.41 0.47 0.53 0.38 0.40 0.43 4.40 4.50 4.60 1.40 1.60 1.75 3.64 --4.25 2.40 2.50 2.60 2.90 3.00 3.10 0.35 0.40 0.45 0.65 0.75 0.85 1.40 1.50 1.60 Pin No. Function 1 RF IN 2 GND 3 RF OUT / Bias Mounting Recommendation (in mm) Note: 1. The number and size of ground via holes in a circuit board is critical for thermal and RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of the lead pin 2 and exposed pad of the device for better RF and thermal performance, as shown in the drawing at the left side. Ordering Information Part Number 2/6 Description ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2010 ASW101 5-3000 MHz MMIC Amplifier Frequency (MHz) APPLICATION CIRCUIT IF 5 150 300 450 Magnitude S21 (dB) 25 24.5 23.5 21.5 Magnitude S11 (dB) -15 -15 -14 -12 Magnitude S22 (dB) -12 -15 -14 -12 Output P1dB (dBm) 17 17 17 17 1) 5 ~ 450 MHz +3.3 V Output IP3 (dBm) 28 29 30 30 Noise Figure (dB) 3.6 3.8 4.0 3.8 Device Voltage (V) 3.3 Current (mA) 40 1) OIP3 is measured with two tones at an output power of +3 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=3.3 V D1=5.6V Zener Diode C4=1 mF C3=100 pF L1=1 mH R1=2.4 kW RF IN C1=1 mF C2=1 mF RF OUT ASW101 S-parameters & K-factor 30 0 25 S11 (dB) Gain (dB) -5 20 15 -10 10 -15 5 0 0 100 200 300 400 500 -20 0 100 200 Frequency (MHz) 300 400 500 Frequency (MHz) 5 0 4 Stability Factor S22 (dB) -5 -10 3 2 -15 1 -20 0 100 200 300 400 500 0 0 500 Frequency (MHz) 3/6 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2010 ASW101 5-3000 MHz MMIC Amplifier APPLICATION CIRCUIT R Bias 3.9 kohm 3.6 kohm Frequency (MHz) 60~110 60~110 20 20.5 Magnitude S21 (dB) Gain Flatness (dB) 0.4 0.4 Magnitude S11 (dB) -9.5 -10 Low Current Magnitude S22 (dB) -9 -11 60 ~ 110 MHz Output P1dB (dBm) 4.5 4.5 Output IP31) (dBm) 12 12 Noise Figure (dB) 2.4 2.4 Device Voltage (V) 3 3 Current (mA) 8 10 IF +3 V 1) OIP3 is measured with two tones at an output power of -5 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=3 V D1=5.6V Zener Diode C4=1 mF C3=1000 pF R Bias= 3.9 kW or 3.6 kW L1=390 nH RF IN RF OUT ASW101 C2=1000 pF C1=1000 pF R1=620 W 25 5 20 0 15 -5 S11 (dB) Gain (dB) S-parameters (R Bias=3.9 kohm) & K-factor 10 5 0 -10 -15 0 50 100 150 200 250 300 -20 0 50 100 Frequency (MHz) 5 0 4 Stability Factor 5 S22 (dB) -5 -10 -15 -20 200 250 300 3 2 1 0 50 100 150 200 250 300 0 0 500 Frequency (MHz) 4/6 150 Frequency (MHz) 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2010 ASW101 5-3000 MHz MMIC Amplifier Frequency (MHz) APPLICATION CIRCUIT 500 900 1750 2000 2400 Magnitude S21 (dB) 21 18 12.5 11 9.5 Magnitude S11 (dB) -10 -10 -11 -10 -8.5 Magnitude S22 (dB) -22 -18 -18 -18 -15 Output P1dB (dBm) 17 17 18 18 18 500 ~ 2500 MHz Output IP3 (dBm) 30 30 31 31 31 +3.3 V Noise Figure (dB) 4.2 3.8 3.9 4.0 4.5 1) Device Voltage (V) 3.3 Current (mA) 40 1) OIP3 is measured with two tones at an output power of +3 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=3.3 V D1=5.6V Zener Diode C4=1 mF C3=100 pF L1=56 nH R1=2.4 kW C1=100 pF RF IN C2=100 pF RF OUT ASW101 S-parameters & K-factor 30 5 25 -40oc 25oc 85oc -5 S11 (dB) 20 Gain (dB) 0 -40oc 25oc 85oc 15 -10 10 -15 5 0 0 500 1000 1500 2000 2500 3000 3500 -20 0 500 1000 Frequency (MHz) -40oc 25oc 85oc -5 2500 3000 3500 4 Stability Factor S22 (dB) -10 -15 -20 3 2 1 -25 0 500 1000 1500 2000 2500 3000 3500 0 0 500 Frequency (MHz) 5/6 2000 5 0 -30 1500 Frequency (MHz) 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2010 ASW101 5-3000 MHz MMIC Amplifier Gain vs. Temperature 60 22 50 20 40 18 Gain (dB) Current (mA) Current vs. Temperature 30 16 Frequency = 900 MHz 14 20 10 -60 -40 -20 0 20 40 60 80 12 -60 100 -40 -20 Temperature ( C) 34 20 32 Output IP3 (dBm) P1dB (dBm) 22 18 16 -40oc 25oc 85oc 14 0 500 1000 1500 2000 28 2500 24 3000 5 30 4 NF (dB) Output IP3 (dBm) 35 25 20 0 500 1000 15 6 8 2000 2500 3000 10 12 3 Frequency = 850 MHz 1 14 0 -60 -40 -20 0 20 40 60 80 100 Temperature (oC) Pout per Tone (dBm) 6/6 1500 2 -40oc 25oc 85oc 4 100 NF vs. Temperature (Frequency = 850MHz) 6 2 80 Frequency (MHz) 40 0 60 -40oc 25oc 85oc 26 Output IP3 vs. Tone Power (Frequency = 2000MHz) -2 40 30 Frequency (MHz) 10 20 Output IP3 vs. Frequency P1dB vs. Frequency 12 0 Temperature (oC) o ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2010