ASL210 5-3000 MHz High Linearity LNA MMIC Features Description ·18.5 dB Gain at 900 MHz The ASL210, a wideband linear low noise amplifier MMIC, has a low noise and high linearity at low bias current, being suitable for use in both receiver and transmitter of telecommunication systems up to 3 GHz. The amplifier is available in an SOT-89 package and passes through the stringent DC, RF, and reliability tests. ·20 dBm P1dB at 900 MHz ·36 dBm Output IP3 at 900 MHz ·0.8 dB NF at 900 MHz ·MTTF > 100 Years ·Single Supply ASL210 Package Style: SOT-89 Typical Performance Parameters Frequency Units Application Circuit Typical MHz 50 450 900 2000 2700 Gain dB 24.5 22.5 18.5 12 10 ·IF ( 50 ~ 200 MHz ) ·IF ( 470 ~ 510 MHz ) S11 dB -12 -15 -20 -18 -14 ·CDMA S22 dB -18 -15 -18 -12 -10 ·GSM dBm 351) 352) 363) 374) 384) ·PCS & DCS Noise Figure dB 2.5 0.8 0.8 0.9 1.2 ·WCDMA Output P1dB dBm 18.5 20 20 20.5 20.5 ·2300 ~ 2700 MHz Current mA 80 67 67 67 67 V 3 3.3 3.3 3.3 3.3 Output IP3 Device Voltage 1) OIP3 is measured with two tones at an output power of +7 dBm/tone separated by 1 MHz. 2) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. 3) OIP3 is measured with two tones at an output power of +12 dBm/tone separated by 1 MHz. 4) OIP3 is measured with two tones at an output power of +11 dBm/tone separated by 1 MHz. Product Specifications Parameters Testing Frequency Units Min Typ MHz 900 Gain dB 18.5 S11 dB -20 S22 dB -18 Output IP3 dBm 36 Noise Figure dB 0.8 Output P1dB dBm 20 Current mA 67 V 3.3 Device Voltage Max Pin Configuration Absolute Maximum Ratings Parameters Rating Operating Case Temperature -40 to +85°C Storage Temperature -40 to +150°C Pin No. Function +5 V 1 RF IN Operating Junction Temperature +150°C 2 GND Input RF Power (CW, 50ohm matched)* 22 dBm 3 RF OUT / Bias Device Voltage * Please find the max. input power data from http://www.asb.co.kr/pdf/Maximum_Input_Power_Analysis.pdf 1/8 ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2011 ASL210 5-3000 MHz High Linearity LNA MMIC Outline Drawing Part No. Lot No. Symbols A L b b1 C D D1 E E1 e1 H S e ASL210 Pxxxx Dimensions (In mm) MIN NOM MAX 1.40 1.50 1.60 0.89 1.04 1.20 0.36 0.42 0.48 0.41 0.47 0.53 0.38 0.40 0.43 4.40 4.50 4.60 1.40 1.60 1.75 3.64 --4.25 2.40 2.50 2.60 2.90 3.00 3.10 0.35 0.40 0.45 0.65 0.75 0.85 1.40 1.50 1.60 Pin No. Function 1 RF IN 2 GND 3 RF OUT / Bias Mounting Recommendation (in mm) Note: 1. The number and size of ground via holes in a circuit board is critical for thermal and RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of the lead pin 2 and exposed pad of the device for better RF and thermal performance, as shown in the drawing at the left side. ESD Classification & Moisture Sensitivity Level ESD Classification HBM Class 1B Voltage Level: 550 V MM Class A Voltage Level: 50 V CAUTION: ESD-sensitive device! Moisture Sensitivity Level (MSL) Level 3 at 260°C reflow 2/8 ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2011 ASL210 5-3000 MHz High Linearity LNA MMIC Frequency (MHz) APPLICATION CIRCUIT IF 50 ~ 200 MHz +3 V 50 100 200 Magnitude S21 (dB) 24.5 24 23 Magnitude S11 (dB) -12 -12 -11 Magnitude S22 (dB) -18 -20 -20 Output P1dB (dBm) 18.5 18.5 18.5 Output IP31) (dBm) 35 35 35 Noise Figure (dB) 2.5 2.4 2.4 Device Voltage (V) 3 3 3 Current (mA) 80 80 80 1) OIP3 is measured with two tones at an output power of +7 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vs=3 V C4=10 mF C3=100 pF L1=1.2 mH C1=1 mF RF IN C2=1 mF RF OUT ASL210 R1=9.1 kW R2=100 W S-parameters & K-factor 30 0 25 S11 (dB) Gain (dB) -5 20 15 10 -10 -15 5 0 0 50 100 150 200 250 300 -20 0 50 100 Frequency (MHz) 150 200 250 300 Frequency (MHz) 5 0 -5 4 Stability Factor S22 (dB) -10 -15 -20 2 1 -25 -30 3 0 0 50 100 150 200 250 300 0 500 3/8 1000 1500 2000 2500 3000 3500 Frequency (MHz) Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2011 ASL210 5-3000 MHz High Linearity LNA MMIC Frequency (MHz) 470 510 Magnitude S21 (dB) 22.5 22 Magnitude S11 (dB) -15 -17 Magnitude S22 (dB) -15 -15 IF Output P1dB (dBm) 20 20 470 ~ 510 MHz Output IP31) (dBm) 35 35 Noise Figure (dB) 0.8 0.9 Device Voltage (V) 3.3 3.3 Current (mA) 67 67 APPLICATION CIRCUIT +3.3 V 1) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vs=3.3 V C5=0.1 mF C4=100 pF L1=220 nH C1=100 pF L2=12 nH RF IN C3=100 pF RF OUT ASL210 L3=47 nH R1=7.5 kW C2=5 pF S-parameters & K-factor 30 0 25 S11 (dB) Gain (dB) -5 20 15 -10 10 -15 5 0 200 300 400 500 600 700 800 -20 200 300 400 Frequency (MHz) 500 600 700 800 Frequency (MHz) 5 0 4 Stability Factor S22 (dB) -5 -10 3 2 -15 1 -20 200 0 300 400 500 600 700 800 0 500 4/8 1000 1500 2000 2500 3000 3500 Frequency (MHz) Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2011 ASL210 5-3000 MHz High Linearity LNA MMIC APPLICATION CIRCUIT CDMA & GSM 824 ~ 960 MHz +3.3 V Frequency (MHz) 824 894 960 Magnitude S21 (dB) 19.5 18.5 18 Magnitude S11 (dB) -15 -20 -15 Magnitude S22 (dB) -20 -18 -15 Output P1dB (dBm) 20 20 19.5 Output IP31) (dBm) 35 35 35.5 Noise Figure (dB) 0.7 0.8 0.8 Device Voltage (V) 3.3 3.3 3.3 Current (mA) 67 67 67 1) OIP3 is measured with two tones at an output power of +12 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=3.3 V C5=0.1 mF C4=100 pF L1=39 nH C1=100 pF L2=6.8 nH RF IN C3=100 pF RF OUT ASL210 L3=47 nH C2=3.3 pF R1=7.5 kW 25 0 20 -5 -10 15 S11 (dB) Gain (dB) S-parameters & K-factor 10 -15 -20 5 -25 0 600 700 800 900 1000 1100 1200 -30 600 700 800 Frequency (MHz) 900 1000 1100 1200 Frequency (MHz) 0 5 -5 4 Stability Factor S22 (dB) -10 -15 -20 2 1 -25 -30 600 3 700 800 900 1000 1100 1200 0 0 500 Frequency (MHz) 5/8 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2011 ASL210 5-3000 MHz High Linearity LNA MMIC Frequency (MHz) 1710 1990 Magnitude S21 (dB) 14 13 Magnitude S11 (dB) -18 -16 Magnitude S22 (dB) -16 -14 PCS & DCS Output P1dB (dBm) 19.5 19.5 1710 ~ 1990 MHz Output IP31) (dBm) 37 37.5 Noise Figure (dB) 0.7 0.8 Device Voltage (V) 3.3 3.3 Current (mA) 67 67 APPLICATION CIRCUIT +3.3 V 1) OIP3 is measured with two tones at an output power of +11 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=3.3 V C5=0.1 mF C4=100 pF L1=39 nH C1=100 pF L2=2.2 nH RF IN C3=100 pF RF OUT ASL210 L3=39 nH C2=1.2 pF R1=7.5 kW S-parameters & K-factor 20 0 -5 -10 S11 (dB) Gain (dB) 15 10 -15 -20 5 -25 0 1500 1600 1700 1800 1900 2000 2100 -30 1500 1600 1700 Frequency (MHz) 5 -5 4 Stability Factor 0 S22 (dB) -10 -15 -20 -25 1500 1900 2000 2100 3 2 1 0 1600 1700 1800 1900 2000 2100 0 500 Frequency (MHz) 6/8 1800 Frequency (MHz) 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2011 ASL210 5-3000 MHz High Linearity LNA MMIC Frequency (MHz) 1920 2170 Magnitude S21 (dB) 13 12 Magnitude S11 (dB) -15 -18 Magnitude S22 (dB) -14 -12 WCDMA Output P1dB (dBm) 20 20.5 1920 ~ 2170 MHz Output IP31) (dBm) 37 37 Noise Figure (dB) 0.8 0.9 Device Voltage (V) 3.3 3.3 Current (mA) 67 67 APPLICATION CIRCUIT +3.3 V 1) OIP3 is measured with two tones at an output power of +11 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=3.3 V C5=0.1 mF C4=100 pF L1=39 nH RF IN C1=100 pF 4 mm C3=100 pF RF OUT ASL210 L3=39 nH C2=1.2 pF R1=7.5 kW S-parameters & K-factor 20 0 -5 -10 S11 (dB) Gain (dB) 15 10 -15 5 -20 0 1700 1800 1900 2000 2100 2200 2300 2400 -25 1700 1800 1900 Frequency (MHz) 5 -5 4 Stability Factor 0 S22 (dB) -10 -15 -20 -25 1700 2100 2200 2300 2400 2500 3000 3500 3 2 1 0 1800 1900 2000 2100 2200 2300 2400 0 500 Frequency (MHz) 7/8 2000 Frequency (MHz) 1000 1500 2000 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2011 ASL210 5-3000 MHz High Linearity LNA MMIC APPLICATION CIRCUIT 2300 ~ 2700 MHz +3.3 V Frequency (MHz) 2300 2500 2700 Magnitude S21 (dB) 11.5 10.5 10 Magnitude S11 (dB) -14 -15 -14 Magnitude S22 (dB) -14 -12 -10 Output P1dB (dBm) 20.5 21 20.5 Output IP31) (dBm) 38 38 38 Noise Figure (dB) 1.0 1.1 1.2 Device Voltage (V) 3.3 3.3 3.3 Current (mA) 67 67 67 1) OIP3 is measured with two tones at an output power of +11 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=3.3 V C5=0.1 mF C4=100 pF L1=39 nH RF IN C1=100 pF 1.5 mm C3=100 pF RF OUT ASL210 L3=39 nH R1=7.5 kW C2=1 pF 20 0 15 -5 S11 (dB) Gain (dB) S-parameters & K-factor 10 5 0 2000 -10 -15 2200 2400 2600 2800 3000 -20 2000 2200 2400 Frequency (MHz) 5 -5 4 Stability Factor 0 S22 (dB) -10 -15 -20 -25 2000 2800 3000 3 2 1 0 2200 2400 2600 2800 3000 0 500 Frequency (MHz) 8/8 2600 Frequency (MHz) 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 February 2011