Ordering number: EN5150B Monolithic Linear IC LA7845N Vertical Deflection Output Circuit Overview Package Dimensions The LA7845N is a vertical deflection output IC for TVs and CRT displays with excellent image quality that use a BUS control system signal processing IC. This IC can drive the direct (even including a DC component) deflection yoke with the sawtooth wave output from the BUS control system signal processing IC. When used in conjunction with Sanyo’s LA7615 series of BUS control system signal processing ICs for TVs, this IC can process all color television signal system functions through the BUS system. Because the maximum deflection current is 2.2 Ap-p, the LA7845N is suited for large screen sets, being capable of driving screens ranging from 33 inches to 37 inches. unit : mm 3075-SIP7H [LA7845N] Features . Low power dissipation due to built-in pump-up circuit . Vertical output circuit . Thermal protection circuit built in . Excellent crossover characteristics . DC coupling possible SANYO : SIP7H Specifications Maximum Ratings at Ta = 25 °C Parameter Symbol Conditions Ratings Maximum supply voltage VCC6 max 40 Output block supply voltage VCC3 max 85 Deflection output current Thermal resistance Allowable power dissipation I 2 max –1.5 to +1.5 θj-c Pd max With arbitrarily large heat sink fins Unit V V Ap-o 4.0 °C/W 11 W Operating temperature Topr –20 to +85 °C Storage temperature Tstg –40 to +150 °C Ratings Unit Operating Conditions at Ta = 25 °C Parameter Symbol Recommended supply voltage VCC6 Operating supply voltage range VCC6 op Recommended deflection output current I 2 p-p Conditions 24 16 to 38 to 2.2 V V Ap-p SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN D1096HA(II)/N3095HA(II)/61595HA(II) No.5150-1/4 LA7845N Operating Characteristics at Ta = 25 °C, VCC6 = 24 V Parameter Pump-up charge saturation voltage Pump-up discharge saturation voltage Deflection output saturation voltage (lower) Deflection output saturation voltage (upper) Idling current Midpoint voltage Symbol Conditions min typ max Unit VS7-1 I 7 = 20 mA 1.8 V VS6-7 I 7 = –1.1 A 3.2 V VS2-1 I 2 = 1.1 A 1.5 V VS3-2 I 2 = –1.1 A 3.5 V 70 13.0 mA V IDL VMID 35 11.0 12.0 Block Diagram Sample Application Circuit (Single power supply) No.5150-2/4 LA7845N Sample Application Circuit (Double power supply) Sample Application Circuit Unit (resistance: Ω, capacitance: F) No.5150-3/4 LA7845N No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. Anyone purchasing any products described or contained herein for an above-mentioned use shall: 1 Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: 2 Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of December, 1996. Specifications and information herein are subject to change without notice. No.5150-4/4