PRELIMINARY ® ® Cree XLamp XP-E2 Color LEDs Product Description FEATURES Table of Contents The XLamp XP-E2 color LEDs build • Available in royal blue, blue, Characteristics........................... 2 on the unprecedented performance of the original XP-E by increasing lumen output up to 10% while providing a single die LED point source for precise optical control. green, & red • Maximum drive current: up to 1 A • Low thermal resistance: as low as 5 °C/W Flux Characteristics..................... 3 Relative Spectral Power Distribution............................... 5 Relative Flux vs. Junction Temperature.............................. 6 The XP‑E2 color LEDs share the •Wide viewing angle: 130°‑135° Electrical Characteristics.............. 7 same footprint as the original XP‑E, • Unlimited floor life at Thermal Design.......................... 8 providing a path more to seamless upgrade lumens and/or greater efficiency while shortening the design cycle for existing XP customers. ≤ 30 °C/85% RH Relative Flux vs. Current............. 9 • Reflow solderable - JEDEC Typical Spatial Distribution..........10 J‑STD‑020C compatible Reflow Soldering Characteristics..11 • Electrically neutral thermal path Notes.......................................12 Mechanical Dimensions..............13 Tape and Reel...........................14 XLamp XP-E2 color LEDs are the Packaging.................................15 ideal choice for lighting applications Bin and Order-Code Format........16 where high light output, maximum Performance Groups – efficacy and precise optical control Brightness................................17 are required, such as LED retrofit Performance Groups – Radiant lamps, outdoor lighting, portable Flux.........................................17 lighting, Performance Groups – Dominant www.cree.com/Xlamp lighting. or indoor directional Wavelength..............................18 Performance Groups – Forward Voltage....................................18 Standard Order Codes and Bins...19 Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 CLD-DSXX Rev 0 Product family data sheet xlamp xp-e2 Color leds Characteristics PRELIMINARY Characteristics Unit Thermal resistance, junction to solder point - royal blue, blue °C/W 9 Thermal resistance, junction to solder point - green °C/W 15 Thermal resistance, junction to solder point - red °C/W 5 Viewing angle (FWHM) - royal blue, blue, green degrees 135 Viewing angle (FWHM) - red degrees 130 Temperature coefficient of voltage - royal blue, blue mV/°C -3.3 Temperature coefficient of voltage - green mV/°C -3.8 Temperature coefficient of voltage - red mV/°C -1.8 ESD classification (HBM per Mil-Std-883D) Minimum Typical Maximum Class 2 DC forward current - royal blue, blue, green mA 1000 DC forward current - red mA 700 V 5 Reverse voltage Forward voltage (@ 350 mA) - royal blue, blue V 3.1 3.25 Forward voltage (@ 350 mA) - green V 3.3 3.5 Forward voltage (@ 350 mA) - red V 2.2 2.5 Forward voltage (@ 1000 mA) - royal blue, blue V 3.4 Forward voltage (@ 1000 mA) - green V 3.8 Forward voltage (@ 1000 mA) - red V 2.65 LED junction temperature °C 150 Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 2 xlamp xp-e2 Color leds PRELIMINARY Flux Characteristics (TJ = 25 °C) - Color The following table provides several base order codes for XLamp XP-E2 color LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult “Bin and Order-Code Format” on page 16. Minimum Radiant Flux @ 350 mA Dominant Wavelength Range Color Flux (mW) Group 30 450 31 475 32 500 Royal Blue 33 525 34 550 35 575 Min. Group DWL (nm) Group DWL (nm) D3 450 D5 465 XPEBRY-L1-0000-00J01 D3 450 D4 460 XPEBRY-L1-0000-00J02 D4 455 D5 465 XPEBRY-L1-0000-00J03 D3 450 D5 455 XPEBRY-L1-0000-00K01 D3 450 D4 460 XPEBRY-L1-0000-00K02 D4 455 D5 465 XPEBRY-L1-0000-00K03 D3 450 D5 455 XPEBRY-L1-0000-00L01 D3 450 D4 460 XPEBRY-L1-0000-00L02 D4 455 D5 465 XPEBRY-L1-0000-00L03 D3 450 D5 455 XPEBRY-L1-0000-00M01 D3 450 D4 460 XPEBRY-L1-0000-00M02 D4 455 D5 465 XPEBRY-L1-0000-00M03 D3 450 D5 455 XPEBRY-L1-0000-00N01 D3 450 D4 460 XPEBRY-L1-0000-00N02 D4 455 D5 465 XPEBRY-L1-0000-00N03 D3 450 D5 465 XPEBRY-L1-0000-00P01 D3 450 D4 460 XPEBRY-L1-0000-00P02 Dominant Wavelength Range Min. Color Group Blue B3 Max. DWL (nm) 465 Order Codes, Max. Group B6 DWL (nm) 485 Base Order Codes Min. Luminous Flux (lm) @ 350 mA Order Code Group Flux (lm) K2 30.6 XPEBBL-L1-0000-00Y01 K3 35.2 XPEBBL-L1-0000-00Z01 M2 39.8 XPEBBL-L1-0000-00201 M3 45.7 XPEBBL-L1-0000-00301 Note: Cree maintains a tolerance of ± 7% on flux and power measurements and ± 1 nm on dominant wavelength measurements. Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 3 xlamp xp-e2 Color leds PRELIMINARY Flux Characteristics (TJ = 25 °C) - Color (continued) Dominant Wavelength Range Min. Color Group Green Max. DWL (nm) G2 520 Group DWL (nm) G4 535 Dominant Wavelength Range Min. Color Group Red R2 Max. DWL (nm) 620 Group R3 DWL (nm) 630 Base Order Codes Min. Luminous Flux (lm) @ 350 mA Order Code Group Flux (lm) Q2 87.4 Q3 93.9 XPEBGR-L1-0000-00B01 Q4 100 XPEBGR-L1-0000-00C01 Q5 107 XPEBGR-L1-0000-00D01 R2 114 XPEBGR-L1-0000-00E01 R3 122 XPEBGR-L1-0000-00F01 Base Order Codes Min. Luminous Flux (lm) @ 350 mA XPEBGR-L1-0000-00A01 Order Code Group Flux (lm) N3 56.8 XPEBRD-L1-0000-00501 N4 62.0 XPEBRD-L1-0000-00601 P2 67.2 XPEBRD-L1-0000-00701 P3 73.9 XPEBRD-L1-0000-00801 Note: Cree maintains a tolerance of ± 7% on flux and power measurements and ± 1 nm on dominant wavelength measurements. Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 4 xlamp xp-e2 Color leds PRELIMINARY Relative Spectral Power Relative Spectral Power Distribution Relative Radiant Power (%) 100 80 60 Blue Green Red 40 20 0 380 430 480 530 580 630 680 730 780 Wavelength (nm) Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 5 xlamp xp-e2 Color leds PRELIMINARY Relative Flux Output vs. Junction Temperature Relative Flux vs. Junction Temperature (IF = 350 mA) 100 Relative Radiant Flux (%) 90 80 70 60 50 Royal Blue 40 30 20 10 0 25 50 75 100 125 150 Relative Flux Output Junction vs. Junction Temperature Temperature (ºC) 100 Relative Luminous Flux (%) 90 80 70 60 Blue Green Red 50 40 30 20 10 0 25 50 75 100 Junction Temperature (°C) Junction Temperature (ºC) 125 150 Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 6 xlamp xp-e2 Color leds PRELIMINARY Electrical Characteristics (Tj = 85ºC) Electrical Characteristics (TJ = 25 °C) 1000 Forward Current (mA) 900 800 700 600 Royal Blue, Blue 500 Green 400 Red 300 200 100 0 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00 Forward Voltage (V) Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 7 xlamp xp-e2 Color leds PRELIMINARY Thermal Design Thermal Design - green The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to Thermal Design - royal blue - same as blue 1200 1200 1000 1000 Maximum Current (mA) Maximum Current (mA) ambient in order to optimize lamp life and optical characteristics. 800 600 Rj-a = 10°C/W Rj-a = 15°C/W Rj-a = 20°C/W Rj-a = 25°C/W 400 200 0 0 20 40 Thermal 60 80Design 100 - red 120 800 600 Rj-a = 20°C/W Rj-a = 25°C/W Rj-a = 30°C/W Rj-a = 35°C/W 400 200 0 0 140 20 40 60 80 100 120 140 Ambient Temperature (ºC) Ambient Temperature (ºC) Royal Blue, Blue Green 800 Maximum Current (mA) 700 600 500 400 Rj-a = 10°C/W Rj-a = 15°C/W Rj-a = 20°C/W Rj-a = 25°C/W 300 200 100 0 0 20 40 60 80 100 120 140 Ambient Temperature (ºC) Red Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 8 xlamp xp-e2 Color leds PRELIMINARY Relative Flux vs. Current (TJ = 25 °C) Relative Intensity vs. Current (Tj = 85ºC) Relative Radiant Flux (%) 250 200 150 Royal Blue 100 50 0 0 100 200 300 400 500 600 700 800 900 1000 Relative Intensity vs. Current (Tj = 85ºC) Forward Current (mA) Relative Luminous Flux (%) 300 250 200 Blue Green 150 Red 100 50 0 0 100 200 300 400 500 600 700 800 900 1000 Forward Current (mA) Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 9 xlamp xp-e2 Color leds PRELIMINARY Typical Spatial Radiation Pattern Typical Spatial Distribution Relative Luminous Intensity (%) 100 80 60 Royal Blue, Blue, Green Red 40 20 0 -90 -70 -50 -30 -10 10 30 50 70 90 Angle (º) Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 10 xlamp xp-e2 Color leds PRELIMINARY Reflow Soldering Characteristics In testing, Cree has found XLamp XP-E2 color LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. Profile Feature Lead-Based Solder Lead-Free Solder 3 °C/second max. 3 °C/second max. Preheat: Temperature Min (Tsmin) 100 °C 150 °C Preheat: Temperature Max (Tsmax) 150 °C 200 °C 60-120 seconds 60-180 seconds 183 °C 217 °C 60-150 seconds 60-150 seconds 215 °C 260 °C 10-30 seconds 20-40 seconds 6 °C/second max. 6 °C/second max. 6 minutes max. 8 minutes max. Average Ramp-Up Rate (Tsmax to Tp) Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) Time Within 5 °C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25 °C to Peak Temperature Note: All temperatures refer to topside of the package, measured on the package body surface. Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 11 xlamp xp-e2 Color leds Notes PRELIMINARY Lumen Maintenance Projections Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document at www.cree.com/xlamp_app_notes/LM80_results. Please read the XLamp Long-Term Lumen Maintenance application note at www.cree.com/xlamp_app_notes/lumen_ maintenance for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note at www.cree.com/xlamp_app_notes/thermal_management for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture Sensitivity In testing, Cree has found XLamp XP-E2 color LEDs to have unlimited floor life in conditions ≤ 30 ºC/85% relative humidity (RH). Moisture testing included a 168-hour soak at 85 ºC/85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. Cree recommends keeping XLamp LEDs in their sealed moisture-barrier packaging until immediately prior to use. Cree also recommends returning any unused LEDS to the resealable moisture-barrier bag and closing the bag immediately after use. Vision Advisory Claim WARNING: Do not look at exposed lamp in operation. Eye injury can result. See LED Eye Safety at www.cree.com/ xlamp_app_notes/led_eye_safety. Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 12 C .65 PRELIMINARY Mechanical Dimensions (TA = 25 °C) 6 All measurements are ±.13 mm unless otherwise indicated. 5 4 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC. 3 Anode B .60 6 5 6 5 1.20 TICE NOTICE D OT THE INFORMATION HISAND PLOT AND THE INFORMATION TIAL. THIS PLOT AND THE INFORMATION PROPRIETARY AND EINTHE PROPRIETARY AND AND ARE THE PROPRIETARY OF CREE, INC. THIS PLOT ATION OF CREE, INC. THIS FORMATION OF CREE, INC.PLOT THIS PLOT DUCED OR DISCLOSED ANYTO ANY EPRODUCED OR DISCLOSED IED, REPRODUCED OR TO DISCLOSED TO ANY HOUT THEWITHOUT WRITTEN CONSENT N WITHOUT THE WRITTEN CONSENT PERSON THE WRITTEN CONSENT 4 5 4 3 4 3 2 3 2.36 3.45 2 2 REVISONS REVISONS REVISO REV REV REV DESCRIPTION DESCRIPTION DESCRIPTION .83 3.20 2.36 2.36 2.36 1.60 3.45 3.45 3.45 3.45 .40 .83 3.20 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° NDED STENCIL PATTERN AREA IS OPENING) C 3.45 3.45 3.45 THIRD ANGLE PROJECTION FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° 2.30 2.30 2.30 .50 .50 .50 .83 .83 D. CRONIN 4600 Silicon Drive Durham, N.C 27703 07/19/12 DATE APPROVED DATE Phone (919) 313-5300 R1.53Fax (919) 313-5558 A TITLE OUTLINE DRAWING XPE G2 MATERIAL SIZE C FINAL PROTECTIVE FINISH SCALE 3 3.30 3.30 3.30 DATE DRAWN BY CHECK SURFACE FINISH: 1.6 2610-00029 SHEET 2 .65 A OF 1 /1 1 R1.53 R1.53R1.53 .65 .65 .65 1.30 1.30 1.30 Side View Top View 3.30 3.30 3.30 REV. DRAWING NO. 22.000 Anode Bottom View 1.15 .60 .65 B 1.20 .50 .60 1.15 1.15 1.15 65 0 xlamp xp-e2 Color leds 1.30 .65 .65 .60 .60 .60 3.30 .50 .50 .50 .60 1.20 1.20 1.20 1.65 .60 .60 A 3.30 .50 3.30 3.30 3.30 .40 .40 .40 1.30 1.30 1.30 3.30 3.30 3.30 1.60 .40 1.30 3.20 3.20 3.20 .40 .40 1.65 1.65 1.65 RECOMMENDED PCB SOLDER PADPad Recommended PCB Solder 50 .50 .40 .40 .40 .50 3.20 .40 .40 .40 1.60 1.60 1.60 RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) Recommended Stencil Pattern .40 .40 3.20 3.20 3.20 6 Copyright © 2013 Cree, Inc. All rights reserved. The COMMENDED PCB Inc. SOLDER RECOMMENDED PCB SOLDER PAD PAD RECOMMENDED PCBPAD SOLDER of Cree, 3.20 Hatched Area is Opening THIRD ANGLE PROJECTION DATE BY DATE DRAWN BY DRAWN BY DRAWN UNLESS OTHERWISE SP DIMENSIONS ARE IN MILLIMETERS AND AFTER TOLERANCE UNLESS SP .XX ± .25 .XXX ± .12 X° ± .5 FOR SHEET METAL PART .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 DATE UNLESS OTHERWISE SPECIFIED UNLESSUNLESS OTHERWISE SPECIFIED OTHERWISE SPECIFIED D. CRONIN 07/19/12 D. CRONIN 07/19/1207/19/12 D. CRONIN SURFACE FINISH: 1.6 DIMENSIONS AREDIMENSIONS IN ARE IN ARE DIMENSIONS IN CHECK DATE CHECK DATE CHECK DATE AND AFTER FINISH. MILLIMETERS AND AFTER MILLIMETERS ANDFINISH. AFTER FINISH. 5 4 MILLIMETERS 3 TOLERANCE UNLESS SPECIFIED: UNLESSUNLESS TOLERANCE SPECIFIED: ® ® RECOMMENDED STENCIL PATTERN RECOMMENDED RECOMMENDED STENCIL PATTERN information in this document isSTENCIL subject toPATTERN change without notice. Cree , theTOLERANCE Cree logo and SPECIFIED: XLamp are registered trademarks .XX ± .XX.25 ± .XX .25± APPROVED DATE .25 APPROVEDAPPROVED DATE DATE (HATCHED AREAAREA IS OPENING) (HATCHED IS OPENING) (HATCHED AREA IS OPENING) TITLE .XXX ± .XXX .125 ±.XXX.125± TITLE TITLE .125 X° ± X° .5 °± X° .5 ±° .5 ° THIRD ANGLE PROJECTION THIRD THIRD ANGLEANGLE PROJECTION PROJECTION MATERIAL MATERIALMATERIAL FOR SHEET METAL PARTS ONLY FOR SHEET METAL PARTS FOR SHEET METALONLY PARTS ONLY .X ± .X 1.5± .X 1.5 ± 1.5 DRAWING NO. SIZE DRAW SIZE SIZE .XX ± .XX.75 ± .XX .75± .75 .XXX ± .XXX .25 ±.XXX.25 ±FINAL .25 PROTECTIVE FINALFINISH PROTECTIVE FINISH FINAL PROTECTIVE FINISH OUTLINE DRA OUTLINE OUT 13 C C C261 DETAIL B SCALE 2 : 1 xlamp xp-e2 Color leds 1.50 2.00 [.079] P2 +.10 +.0039 4.00 [.157] Po -.00[.0591-.0000]Do PRELIMINARY 1.75 [.069] E1 Tape and Reel 4.39 [.173] 3.7 +/-0.1mm Bo All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard. 12.00 [.472] 5.50 [.217]F NOMINAL 12.30 [.484] MAX 2.00 [.079] W P2 10.25 [.404] E2 1.50 4.00 [.157] Po 1.50 [.059] D1 8.00 [.315] P 4.0±.1 +.10 -.00[ .096 +.0039 -.0000] Ko 1.75 [.069] E1 +.10 +.0039 +.10 +.0039 1.50 -.00[.0591-.0000]Do -.00[.0591-.0000]Do 3.7 +/-0.1mm Ao Cathode Side 3.7mm8.00 +/-0.1mm [.315] Bo - P 2.46mm +0.1/-0mm Ko - +.3 12.0 .0 5.50 [.217]F 5.50 [.217]F 8.0±.1 3.7mm +/-0.1mm 4.39 [.173] 8.00 [.315]8.00 [.315] P P 7.3 ° 7.3 ° Anode Side (denoted by + and circle) 3.7 +/-0.1mm Ao 7.3 ° .30 [.012] T Ko .30 [.012] .30 [.012] T T +.10+.0039 +.0039 +.10 2.46.096 .096 Ko -.00[-.0000] -.0000] -.00[ 2.46 4.39 [.173] 3.7 +/-0.1mm 3.7 +/-0.1mm Bo Bo 2.5±.1 +.10 +.0039 2.46 .096 -.00[ -.0000] 1.50 [.059]1.50 [.059] D1 D1 4.39 [.173]4.39 [.173] 3.7 +/-0.1mm Bo 12.30 [.484] 10.2512.30 [.484] MAX [.404] MAX W W E2 10.25 [.404] E2 1.50 [.059] D1 4.39 [.173] 12.30 [.484] MAX W 12.00 [.472] 12.00 [.472] NOMINALNOMINAL 10.25 [.404] E2 1.5±.1 POCKET SIZE Ao - All dimensions in mm. 1.75 [.069]1.75 [.069] E1 E1 12.00 [.472] 5.50 [.217]F NOMINAL 7.3 ° 1.75±.10 -.00[.0591-.0000]Do 4.39 [.173] .30 [.012] T 4.00 [.157]4.00 [.157] Po Po 2.46 4.39 [.173] 1.50 2.00 [.079]2.00 [.079] P2 P2 +.10 +.0039 Ko POCKET SIZE Ao - 3.7mm +/-0.1mm Bo - 3.7mm +/-0.1mm 2.46mm +0.1/-0mm POCKET POCKET SIZE SIZE Ko - - 3.7mm +/-0.1mm Ao - Ao 3.7mm +/-0.1mm END - 3.7mm +/-0.1mm Bo - Bo 3.7mm +/-0.1mm START +0.1/-0mm 2.46mm +0.1/-0mm - 2.46mm Ko - Ko 6 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE, INC. 5 4 6 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT 190 OF CREE, INC. 3 2 ÓÉ Foxit PDF Editor ±à¼°æȨËùÓÐ (c) by Foxit Software Company, 2004 ½öÓÃÓÚÆÀ¹À¡£ Loaded Pockets (1,000 Lamps) Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) D User Feed Direction 3.7 +/-0.1mm 3.7 +/-0.1mm Ao Ao 5 4 3 ÓÉ Foxit PDF Editor ±à¼°æȨËùÓÐ (c) by Foxit Software Company, 2004 ½öÓÃÓÚÆÀ¹À¡£ 16.40 1 Leader 400mm (min) of empty pockets with at least 100mm sealed by tape (50 empty pockets min.) 2 D 1 User Feed Direction Cover Tape D C D C 16.40 190 61 +/-0.5 Pocket Tape OD 7.5 C +2.00 12.40 0 MEASURED AT HUB '' C B B 13mm 13 7" OD 61 +/-0.5 12.40 7.5 '' MEASURED AT INSIDE EDGE +2.00 12.40 0 MEASURED AT HUB Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. B B A 13 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS & BEFORE FINISH. TOLERANCE UNLESS SPECIFIED: .X ± 0.3 .XX ± .13 DRAWN BY LIUDEZHI 14 DATE 2012/5/25 CHECK DATE APPROVED DATE 4600 Silicon Drive Durham, N.C 27703 Phone (919) 361-4770 TITLE A xlamp xp-e2 Color leds Packaging PRELIMINARY Unpackaged Reel Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Label CREE Binwith Code Cree Bin & Barcode LabelLot # Code, Qty, Label with Cree Bin Code, Qty, Reel ID Label with Cree Bin Label with Customer P/N, Qty,Qty, Lot #, Lot PO # # Code, Packaged Reel Patent Label Label with Customer Order Label with Cree Order Code, Code, Qty, Reel ID, PO # Qty, Reel ID, PO # Label with Cree Bin Code, Qty, Reel ID Boxed Reel Label with Cree Order Code, Qty, Reel ID, PO # Label with Cree Bin Code, Qty, Reel ID Patent Label (on bottom of box) Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 15 xlamp xp-e2 Color leds PRELIMINARY Bin and Order-Code Format This document describes the product nomenclature required to select and order Cree’s XLamp XP-E2 color LEDs. XLamp XP-E2 color LEDs are tested and sorted into bins which are then combined into orderable kits identified by an order code. All XLamp LEDs are tested and sorted by color and brightness into a unique bin. Each bin contains LEDs from only one color and brightness group and is uniquely identified by a bin code. Color XLamp LEDs are sorted by dominant wavelength (color) and luminous or radiant flux (brightness). Amber, red-orange and red LEDs are additionally binned into forward voltage bins. LEDs are shipped on reels containing LEDs from one bin and are always labeled with the appropriate bin code. Kits contain LEDs from a number of similar bins and are fully defined by their order codes. A full explanation of the order codes for XLamp XP-E2 color LEDs, as well as a list of standard order codes, is provided in this document. Bin codes and order codes are configured in the following manner: Order Code Bin Code Series XPC = XP-C XPE = XP-E XPG = XP-G Series XPC = XP-C XPE = XP-E XPG = XP-G Color specification 01 = Outdoor White L1 = Standard CRI H1 = 80 CRI Minimum P1 = 85 CRI Minimum U1 = 90 CRI Minimum Color specification 01 = Outdoor White L1 = Standard CRI H1 = 80 CRI Minimum P1 = 85 CRI Minimum U1 = 90 CRI Minimum Luminous or radiant flux group Kit Number Internal code SSSCCC-BD-HHHH-NNNNN Internal code Color WHT = White HEW = High Efficiency White BWT = Gen 2 White ROY = Royal Blue BRY = Gen 2 Royal Blue BLU = Blue BBL = Gen 2 Blue GRN = Green BGR = Gen 2 Green AMB = Amber RDO = Red-Orange RED = Red BRD = Gen 2 Red SSSCCC-BD-WWW-FF-G-AA Forward voltage group (amber, red-orange, red, high-efficiency white) Chromaticity bin or dominant-wavelength group Color WHT = White HEW = High Efficiency White BWT = Gen 2 White ROY = Royal Blue BRY = Gen 2 Royal Blue BLU = Blue BBL = Gen 2 Blue GRN = Green BGR = Gen 2 Green AMB = Amber RDO = Red-Orange RED = Red BRD = Gen 2 Red Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 16 xlamp xp-e2 Color leds PRELIMINARY Performance Groups – Brightness XLamp XP-E2 color LEDs (except Royal Blue) are tested for luminous flux and placed into one of the following luminousflux groups: Group Code Min. Luminous Flux @ 350 mA (lm) Max. Luminous Flux @ 350 mA (lm) J 23.5 30.6 K2 30.6 35.2 K3 35.2 39.8 M2 39.8 45.7 M3 45.7 51.7 N2 51.7 56.8 N3 56.8 62.0 N4 62.0 67.2 P2 67.2 73.9 P3 73.9 80.6 P4 80.6 87.4 Q2 87.4 93.9 Q3 93.9 100 Q4 100 107 Q5 107 114 R2 114 122 R3 122 130 R4 130 139 R5 139 148 S2 148 156 S3 156 164 Performance Groups – Radiant Flux (TJ = 25 °C) XLamp XT-E2 Royal Blue LEDs are tested for radiant flux and placed into one the following bins. Group Code Minimum Radiant Flux (mW) Maximum Radiant Flux (mW) 31 (K) 475 500 525 32 (L) 500 33 (M) 525 550 34 (N) 550 575 35 (P) 575 600 36 (Q) 600 625 Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 17 xlamp xp-e2 Color leds PRELIMINARY Performance Groups – Dominant Wavelength Color XLamp LEDs are tested for dominant wavelength (DWL) and sorted into one of the DWL bins defined below. Color DWL Group Min. DWL (nm) @ 350 mA Max. DWL (nm) @ 350 mA D3 450 455 D4 455 460 D5 460 465 B3 465 470 B4 470 475 B5 475 480 Royal Blue Blue Green Amber Red-Orange Red B6 480 485 G2 520 525 G3 525 530 G4 530 535 A2 585 590 A3 590 595 O3 610 615 O4 615 620 R2 620 625 R3 625 630 Performance Groups – Forward Voltage Amber, red-orange and red XLamp LEDs are tested for forward voltage and sorted into one of the forward voltage bins defined below. Forward Voltage Group Min. Forward Voltage @ 350 mA Max. Forward Voltage @ 350 mA B 1.75 2.0 C 2.0 2.25 D 2.25 2.5 E 2.5 2.75 F 2.75 3.0 G 3.0 3.25 H 3.25 3.5 J 3.5 3.75 Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 18 xlamp xp-e2 Color leds PRELIMINARY Standard Order Codes and Bins (XP-E2 Color, TJ = 25 °C) XLamp XP-E2 LED Standard Order Codes - Royal Blue Color Minimum Radiant Flux @ 350 mA Group 30 31 32 Flux (mW) 450 475 500 Royal Blue 33 34 35 525 550 575 Dominant Wavelength (nm) Min. Max. Order Codes Group DWL (nm) Group DWL (nm) D3 450 D5 465 XPEBRY-L1-0000-00J01 D3 450 D4 460 XPEBRY-L1-0000-00J02 D4 455 D5 465 XPEBRY-L1-0000-00J03 D3 450 D5 455 XPEBRY-L1-0000-00K01 D3 450 D4 460 XPEBRY-L1-0000-00K02 D4 455 D5 465 XPEBRY-L1-0000-00K03 D3 450 D5 455 XPEBRY-L1-0000-00L01 D3 450 D4 460 XPEBRY-L1-0000-00L02 D4 455 D5 465 XPEBRY-L1-0000-00L03 D3 450 D5 455 XPEBRY-L1-0000-00M01 D3 450 D4 460 XPEBRY-L1-0000-00M02 D4 455 D5 465 XPEBRY-L1-0000-00M03 D3 450 D5 455 XPEBRY-L1-0000-00N01 D3 450 D4 460 XPEBRY-L1-0000-00N02 D4 455 D5 465 XPEBRY-L1-0000-00N03 D3 450 D5 465 XPEBRY-L1-0000-00P01 D3 450 D4 460 XPEBRY-L1-0000-00P02 * Cree XLamp XP Family order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity or DWL bin restrictions specified by the order code. Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 19 xlamp xp-e2 Color leds PRELIMINARY Standard Order Codes and Bins (XP-E2 Color, TJ = 25 °C) - Continued XLamp XP-E2 LED Standard Order Codes - Color Color Min. Luminous Flux (lm) @ 350 mA* Group Flux (lm) K2 30.6 K3 35.2 Blue M2 M3 Q2 Q3 Q4 39.8 45.7 87.4 93.9 100 Green Q5 R2 R3 N3 N4 107 114 122 56.8 62 Red P2 67.2 P3 73.9 Dominant Wavelength (nm) Min. Max. Order Codes Group DWL (nm) Group DWL (nm) B3 465 B6 485 XPEBBL-L1-0000-00Y01 B3 465 B5 480 XPEBBL-L1-0000-00Y02 B4 470 B5 480 XPEBBL-L1-0000-00Y05 B3 465 B6 485 XPEBBL-L1-0000-00Z01 B3 465 B5 480 XPEBBL-L1-0000-00Z02 B4 470 B5 480 XPEBBL-L1-0000-00Z05 B3 465 B6 485 XPEBBL-L1-0000-00201 B3 465 B5 480 XPEBBL-L1-0000-00202 B4 470 B5 480 XPEBBL-L1-0000-00205 B3 465 B6 485 XPEBBL-L1-0000-00301 B3 465 B5 480 XPEBBL-L1-0000-00302 B4 470 B5 480 XPEBLU-L1-0000-00305 G2 520 G4 535 XPEBGR-L1-0000-00A01 G2 520 G3 530 XPEBGR-L1-0000-00A02 G3 525 G4 535 XPEBGR-L1-0000-00A03 G2 520 G4 535 XPEBGR-L1-0000-00B01 G2 520 G3 530 XPEBGR-L1-0000-00B02 G3 525 G4 535 XPEBGR-L1-0000-00B03 G2 520 G4 535 XPEBGR-L1-0000-00C01 G2 520 G3 530 XPEBGR-L1-0000-00C02 G3 525 G4 535 XPEBGR-L1-0000-00C03 G2 520 G4 535 XPEBGR-L1-0000-00D01 G2 520 G3 530 XPEBGR-L1-0000-00D02 G3 525 G4 535 XPEBGR-L1-0000-00D03 G2 520 G4 535 XPEBGR-L1-0000-00E01 G2 520 G3 530 XPEBGR-L1-0000-00E02 G3 525 G4 535 XPEBGR-L1-0000-00E03 G2 520 G4 535 XPEBGR-L1-0000-00F01 XPEBGR-L1-0000-00F02 G2 520 G3 530 G3 525 G4 535 XPEBGR-L1-0000-00F03 R2 620 R3 630 XPEBRD-L1-0000-00501 R2 620 R2 625 XPEBRD-L1-0000-00502 R2 620 R3 630 XPEBRD-L1-0000-00601 R2 620 R2 625 XPEBRD-L1-0000-00602 R2 620 R3 630 XPEBRD-L1-0000-00701 R2 620 R2 625 XPEBRD-L1-0000-00702 R2 620 R3 630 XPEBRD-L1-0000-00801 R2 620 R2 625 XPEBRD-L1-0000-00802 * Cree XLamp XP Family order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity or DWL bin restrictions specified by the order code. Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. 20