RICHMOND 8300 SERIES Specifications: Electrical Properties Surface Resistance: Outer Surface Aluminum Layer Inner Surface Typical Values Test Procedures/Method <1011 ohms <102 ohms <1011 ohms Static Shielding Charge Generation (nC/in2) Capacitance Probe (to dissipate 1 KV) <20 nJ Teflon: -0.03 Quartz: +0.10 <30V ANSI/ESD S11.11 ANSI/ESD S11.11 ANSI/ESD S11.11 ANSI/ESD S11.31 Modified Incline Plane Modified Incline Plane ANSI/EIA 541/Appendix E, 1kV Discharge Physical Properties: Bag Thickness: Polyester Layer 0.5 Mils Static Dissipative PET film ASTM D-2103 Aluminum Layer 10-25 Angstroms Polyethylene Layer 2.5 Mils Static Dissipative PE film ASTM D-2103 Total Thickness 3.0 to 3.1 Mils ASTM D-2103 Light Transmission (%) 40% (Tobias) ASTM D-1003 Seam Strength Pass ANSI/ESD S541 Tear Strength (lbs) >25 ASTM D-1004 Puncture Resistance (lbs) >10 ASTM D-2065 MVTR (gms / 100 in2 / 24 hrs, 100°F) 0.40 ASTM F-1249 Burst Strength (psi) >50 psi FTMS 101C, 2065.1 Heat Seal >10 lbs/in. 375°F, 1/2 sec 60 psi Abrasion Resistance >30 cycles Sutherland Abr. (.0000 Steel Wool) Outgassing Pass ASTM E595 Non-corrosive Pass MIL-STD-3010, M3005 Side Weld Seals 3/8 in. Item No. Size (in.) W x L Item No. Size (in.) WxL 48500 4 x 4 48509 10 x 14 48501 4 x 6 48510 11 x 15 48502 5 x 8 48511 12 x 16 48503 6 x 8 48512 12 x 18 48504 6 x 10 48513 14 x 16 48505 8 x 8 48514 14 x 18 48506 8 x 10 48515 14 x 24 48507 8 x 12 48516 18 x 24 48508 10 x 12 Packaged 100 per package Chemical Properties Corrosion Polycarbonate Capability, No Amines N-Octanoic Acid No effect on aluminum, copper, silver, Sn-Pb coated foil, stainless steel, low carbon steel High Performance Yes Static Dissipative Not present Abrasion Resistant Coating Mixed Unsortable Plastic Scrap 7 Mixed unsortable plastic scrap shall contain assorted plastics of multiple grades that are co-extruded, bonded or laminated together which are unsortable into individual grades. Protektive Pak’s bags are recyclable Employee Owned Polyester Layer Static Dissipative Inner Polyethylene Layer A fundamental ESD control principle (see ANSI/ESD S20.20 Foreword): ESD susceptible items should be transported and stored outside an Electrostatic protected Area enclosed in low charging, static shielding protective packaging. The bag’s material meets the performance specification requirements of ANSI/ESD S541. Bag is free of amines, N-octanoic acid, and heavy metals. Made in the United States of America RICHMOND 8300, TRANSPARENT STATIC SHIELDING BAG (METAL OUT) PROTEKTIVE PAK 13520 MONTE VISTA AVENUE, CHINO, CA 91710 PHONE (909) 627-2578, FAX (909) 363-7331 www.ProtektivePak.com © 2012 DESCO INDUSTRIES INC. Aluminum Shielding Layer DRAWING NUMBER 48500 DATE: December 2012