LITE-ON TECHNOLOGY CORP. Property of Lite-on Only 6N137 – High Speed 10MBd Optocouplers Aug 2008 DESCRIPTION FEATURES These diode-transistor photocouplers consist of an AlGaAs LED optically coupled to a high speed photodetector. The output features is an open collector and coupler parameters are guaranteed over the temperature range from -40℃~85℃. The internal shield * High speed – 10MBd provides a guaranteed Common Mode Transient Immunity (typical) 10KV/μs * Tape and reel packaging- * Common mode rejection - 10KV/μs * UL, CSA, IEC/EN/DIN EN60747-5-2 – Pending * Dual-in-line package- 6N137 * Wide lead spacing package- 6N137M * Surface mounting package- 6N137S 6N137S-TA/6N137S-TA1 APPLICATIONS * High Voltage Isolation * Line receivers * Feedback Element in Switching Mode Power Supplies * High Speed Logic Ground Isolation – TTL/TTL, TTL/CMOS, TTL/LSTTL * Pulse transformer replacement * Power transistor isolation in motor drives * Microprocessor system interfaces * Ground loop elimination Schematic Pin Define 1. NC 2. Anode 3. Cathode 4. NC 5. GND 6. Vo 7. VE 8. Vcc Truth Table (Positive Logic) Input ON OFF ON OFF ON OFF EN H H L L NC NC Output L H H H L H A 0.1uF bypass capacitor must be connected between pin8 and pin5. Part No. : 6N137 Series (Preliminary Date Sheet) BNS-OD-C131/A4 Page : 1 of 10 LITE-ON TECHNOLOGY CORP. Property of Lite-on Only OUTLINE DIMENSIONS 6N137: 6N137M Part No. : 6N137 Series (Preliminary Date Sheet) BNS-OD-C131/A4 Page : 2 of 10 LITE-ON TECHNOLOGY CORP. Property of Lite-on Only OUTLINE DIMENSIONS 6N137S *1. Year date code. *2. 2-digit work week. *3. Factory identification mark shall be marked (Z: Taiwan, Y: Thailand). Part No. : 6N137 Series (Preliminary Date Sheet) BNS-OD-C131/A4 Page : 3 of 10 LITE-ON TECHNOLOGY CORP. Property of Lite-on Only TAPING DIMENSIONS 6N137S-TA 6N137S-TA1 Description Tape wide Pitch of sprocket holes Distance of compartment Distance of compartment to compartment Part No. : 6N137 Series (Preliminary Date Sheet) BNS-OD-C131/A4 Symbol W P0 F P2 P1 Dimensions in mm ( inches ) 16 ± 0.3 ( .63 ) 4 ± 0.1 ( .15 ) 7.5 ± 0.1 ( .295 ) 2 ± 0.1 ( .079 ) 12 ± 0.1 ( .472 ) Page : 4 of 10 LITE-ON TECHNOLOGY CORP. Property of Lite-on Only ABSOLUTE MAXIMUM RATING ( Ta = 25°C unless otherwise specified) PARAMETER SYMBOL RATING UNIT Forward Current IF 25 mA Reverse Voltage VR 5 V Power Dissipation P 40 mW Supply Voltage (1minute max) VCC 7 V Output Voltage VO 7 V Output Current IO 50 mA Power Dissipation PO 85 mW Isolation Voltage Viso 5000 Vrms Operating Temperature Topr -40 ~ +85 °C Storage Temperature Tstg -55 ~ +125 °C Soldering Temperature Tsol 260 for 10 sec °C INPUT OUTPUT Note 1. AC For 1 Minute, R.H. = 40 ~ 60% Isolation voltage shall be measured using the following method. (1) Short Pin 1 to Pin4 on the primary side and Pin 5 to Pin 8 on the secondary side. (2) The isolation voltage tester with zero-cross circuit shall be used. (3) The waveform of applied voltage shall be a sine wave. 2. For 10 sec. Part No. : 6N137 Series (Preliminary Date Sheet) BNS-OD-C131/A4 Page : 5 of 10 LITE-ON TECHNOLOGY CORP. Property of Lite-on Only ELECTRICAL - OPTICAL CHARACTERISTICS ( TA = 0~70°C, unless otherwise specified ) PARAMETER SYMBOL MIN. TYP.** MAX. UNIT CONDITIONS Input Input Forward Voltage VF — 1.45 1.7 ΔVF/ΔTa — -1.6 — BVR 5.0 — — V High Level Supply Current ICCH — 7 10 mA Low Level Supply Current ICCL — 9 13 mA Low Level Enable Current IEL — -0.8 -1.6 mA High Level Enable Current IEH — -0.6 -1.6 mA High Level Enable Voltage VEH 2.0 Low Level Enable Voltage VEL Input Forward Voltage Temperature Coefficient Input Reverse Voltage V Ta=25℃, IF =10mA mV/℃ IF =10mA Ta=25℃, IR=10μA Output 0.8 IF=0mA, VE=0.5V VCC=5.5V IF=10mA, VE=0.5V VCC=5.5V VCC=5.5V, VE=0.5V VCC=5.5V, VE=2.0V V IF=10mA,VCC=5.5V V IF=10mA,VCC=5.5V ** All typical at TA = 25℃ Part No. : 6N137 Series (Preliminary Date Sheet) BNS-OD-C131/A4 Page : 6 of 10 LITE-ON TECHNOLOGY CORP. Property of Lite-on Only SWITCHING SPECIFICATIONS (AC) ( TA = -40~85°C, VCC = 5V, IF =7.5mA unless otherwise specified ) PARAMETER Propagation Delay time to Logic Low Output (1)→(0) SYM. MIN. TYP** MAX. 25 30 75 tPHL UNIT ns RL =350Ω CL = 15pF ns RL =350Ω CL = 15pF 100 Propagation Delay time to Logic High Output (0)→(1) 25 40 75 tPLH 100 Pulse Width Distortion ∣tPHL- tPLH∣ 10 ns Output Rise Time (10%~90%) tr 50 ns Output Fall time (90%~10%) tf 12 ns Enable Propagation Delay Time at high level output(1) tELH 20 ns Enable Propagation Delay Time at low level output(0) tEHL 20 ns Instantaneous common mode rejection at high logic output (1) Instantaneous common mode rejection at low logic output (0) ｜CMH｜ ｜CML｜ 1 1 10 10 — — CONDITIONS KV / μs KV / μs RL =350Ω CL = 15pF RL =350Ω CL = 15pF RL =350Ω CL = 15pF IF=7.5mA VEH =3.5V RL =350Ω CL = 15pF IF=7.5mA VEH =3.5V RL =350Ω CL = 15pF IF=0mA VOH(Min)=2.0V ｜VCM｜=50VP-P, RL=350Ω IF=7.5mA VOH(Max)=0.8V ｜VCM｜=50VP-P, RL=350Ω ** All typical at TA = 25℃ Part No. : 6N137 Series (Preliminary Date Sheet) BNS-OD-C131/A4 Page : 7 of 10 LITE-ON TECHNOLOGY CORP. Property of Lite-on Only SWITCHING TEST CIRCUITS (AC) Switching Time Test Circuit ( tPHL tPLH, tr and tf ) Switching Time Test Circuit ( tEHL tELH) Common Mode Immunity Test Circuit Part No. : 6N137 Series (Preliminary Date Sheet) BNS-OD-C131/A4 Page : 8 of 10 LITE-ON TECHNOLOGY CORP. Property of Lite-on Only ISOLATION CHARACTERISTICS ( TA = -40~85°C, VCC = 5V, IF =7.5mA unless otherwise specified) PARAMETER SYMBOL MIN. TYP.** MAX. Isolation Resistance (Input-output) Note4. RI-O — 1012 — Capacitance (Input-output) Note4. CI-O — 0.6 — UNIT CONDITIONS Ta=25℃, RH<45%, VI-O=500V DC pF f=1MHz TRANSFER CHARACTERISTICS(DC) ( TA = -40~85°C, VCC = 5V, IF =7.5mA unless otherwise specified) PARAMETER High Level Output Current Low Level Output Voltage Input Threshold Current SYMBOL MIN. TYP.** MAX. IOH VOL IFTH 100 0.35 3 0.6 5 UNIT CONDITIONS uA VCC=5.5V, Vo=0.5V IF=250μA, VE=2.0V V VCC=5.5V, IF=5mA, VE=2.0V IOL=13mA mA VCC=5.5V, Vo=0.5V IOL=13mA, VE=2.0V ** All typical at Vcc=5V,TA = 25℃ Note: 1. AC For 1 Minute, R.H. = 40 ~ 60% Isolation voltage shall be measured using the following method. (1) Considered a two-terminal device: Pin 1,2,3,4 shorted together and Pin 5,6,7,8 shorted together. (2) The isolation voltage tester with zero-cross circuit shall be used. (3) The waveform of applied voltage shall be a sine wave. 2. For 10 sec. 3. Pin5 and Pin8 must connect a bypass 0.1uF capacitor. Part No. : 6N137 Series (Preliminary Date Sheet) BNS-OD-C131/A4 Page : 9 of 10 LITE-ON TECHNOLOGY CORP. Property of Lite-on Only Notes: - Lite-On is continually improving the quality, reliability, function or design and Lite-On reserves the right to make changes without further notices. - The products shown in this publication are designed for the general use in electronic applications such as office automation equipment, communications devices, audio / visual equipment, electrical application and instrumentation. - For equipment/devices where high reliability or safety is required, such as space applications, nuclear power control equipment, medical equipment, etc, please contact our sales representatives. - When requiring a device for any”specific” application, please contact our sales in advice. - If there are any questions about the contents of this publication, please contact us at your convenience. - The contents described herein are subject to change without prior notice. - Do not immerse unit’s body in solder paste. Part No. : 6N137 Series (Preliminary Date Sheet) BNS-OD-C131/A4 Page : 10 of 10