TI TC210

TC210
192- × 165-PIXEL CCD IMAGE SENSOR
SOCS009B – OCTOBER 1986 – REVISED MAY 1990
•
•
•
•
•
•
•
•
•
•
Full-Frame Operation
Antiblooming Capability
Single-Phase Clocking for Horizontal and
Vertical Transfers
Fast Clear Capability
Dynamic Range . . . 60 dB Typical
High Blue Response
High Photoresponse Uniformity
Solid-State Reliability With No Image
Burn-In, Residual Imaging, Image
Distortion, Image Lag, or Microphonics
6-Pin Dual-In-Line Ceramic Package
Square Image Area:
– 2640 µm by 2640 µm
– 192 Pixels (H) by 165 Pixels (V)
– Each Pixel 13.75 µm (H) by 16 µm (V)
DUAL-IN-LINE PACKAGE
(TOP VIEW)
ABG 1
VSS 2
ADB 3
ÉÉÉÉ
ÉÉÉÉ
ÉÉÉÉ
ÉÉÉÉ
ÉÉÉÉ
6 IAG
5 SRG
4 OUT
description
The TC210 is a full-frame charge-coupled device (CCD) image sensor designed specifically for medical and
industrial applications requiring ruggedness and small size. The image-sensing area is configured into 165
horizontal lines each containing 192 pixels. Twelve additional pixels are provided at the end of each line to
establish a dark reference and line clamp. The antiblooming feature is activated by supplying clock pulses to
the antiblooming gate, an integral part of each image-sensing element. The charge is converted to signal voltage
at 4 µV per electron by a high-performance structure with built-in automatic reset and a voltage-reference
generator. The signal is further buffered by a low-noise two-stage source-follower amplifier to provide high
output-drive capability.
The TC210 is supplied in a 5-mm (0.20-in) diameter ceramic and clear plastic molded package with a glass
window. The glass window can be cleaned using any standard method for cleaning optical assemblies or by
wiping the surface with a cotton swab soaked in alcohol.
The TC210 is characterized for operation from – 10°C to 45°C.
This MOS device contains limited built-in gate protection. During storage or handling, the device leads should be shorted together
or the device should be placed in conductive foam. In a circuit, unused inputs should always be connected to VSS. Under no
circumstances should pin voltages exceed absolute maximum ratings. Avoid shorting OUT to VSS during operation to prevent
damage to the amplifier. The device can also be damaged if the output terminals are reverse-biased and an excessive current is
allowed to flow. Specific guidelines for handling devices of this type are contained in the publication Guidelines for Handling
Electrostatic-Discharge-Sensitive (ESDS) Devices and Assemblies available from Texas Instruments.
Copyright  1990, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2-3
TC210
192- × 165-PIXEL CCD IMAGE SENSOR
SOCS009B – OCTOBER 1986 – REVISED MAY 1990
functional block diagram
165
1
ABG
6
IAG
3
ADB
ÇÇÇÇÇÇÇÇÇÇÇÇ
ÇÇÇÇÇÇÇÇÇÇÇÇ
1
192
1
4
Serial Register
OUT
5
SRG
Clear Gate
12 Dark Pixels
2
192 Image Pixels
VSS
6 Dummy Pixels
Terminal Functions
TERMINAL
I/O
DESCRIPTION
NAME
NO.
ABG
1
VSS
ADB
2
3
I
Supply voltage for amplifier drain bias
OUT
4
O
Output signal
SRG
5
I
Serial-register gate
IAG
6
I
Image-area gate
I
Antiblooming gate
Amplifier ground
functional description
The image-sensing area consists of 165 horizontal image lines each containing 192 photosensitive elements
(pixels). Each pixel is 13.75 µm (horizontal) by 16.00 µm (vertical). As light enters the silicon in the
image-sensing area, free electrons are generated and collected in potential wells (see Figure 1). During this
time, the antiblooming gate is activated by applying a burst of pulses. This prevents blooming caused by the
spilling of charge from overexposed elements into neighboring elements. The antiblooming gate is typically held
at a midlevel voltage during readout. The quantity of charge collected in each pixel is a linear function of the
incident light and the exposure time. After exposure and under dark conditions, the charge packets are
transferred from the image-area to the serial register at the rate of one image line per each clock pulse applied
to the image-area gate. Once an image line has been transferred into the serial register, the serial-register gate
can be clocked until all of the charge packets are moved out of the serial register to the charge detection node
at the amplifier input.
There are 12 dark pixels to the right of the 192 image pixels on each image line. These dark pixels are shielded
from incident light and the signal derived from them can be used to generate a dark reference for restoration
of the video black level on the next image line.
2-4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TC210
192- × 165-PIXEL CCD IMAGE SENSOR
SOCS009B – OCTOBER 1986 – REVISED MAY 1990
functional description (continued)
Each clock pulse applied to the image-area gate causes an automatic fast clear of the 192 image pixels and
12 dark pixels of the serial register before the next image line is transferred into the serial register. (Note that
the six dummy pixels at the front of the serial register, which are used to transport charge packets from the serial
register to the amplifier input, are not cleared by the image-area gate clock.) The automatic fast-clear feature
can be used to initialize the image area by transferring all 165 image lines to the serial-register gate under dark
conditions without clocking the serial-register gate.
Potential Wells
Vertical
16 µm
Barriers
Antiblooming Gate
Horizonal
13.75 µm
Representative
Top View of
Pixels
Channel Stop
Virtual
Phase
Cross Section
of Pixels
Clocked
Phase
(imagearea
gate)
Virtual
Phase
Clocked
Phase
(imagearea
gate)
Virtual
Phase
Clocked
Phase
(imagearea
gate)
ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ
ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ
ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ
1 Pixel
IAG Low
Etched
Polysilicon
Insulating Oxide
Silicon
ABG
Low
ABG
Intermediate
Cross Section
of Potentials
in Silicon
IAG High
ABG High
Direction of Vertical Charge Transfer
Figure 1. Charge Accumulation and Transfer Process
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2-5
TC210
192- × 165-PIXEL CCD IMAGE SENSOR
SOCS009B – OCTOBER 1986 – REVISED MAY 1990
Readout
Integration
ABG
165 Cycles
IAG
210 Cycles
SRG
IAG
tw1
t3
t2
SRG
tw2
t1
t4
Figure 2. Timing Diagram, Noninterlace Mode
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range for ADB (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to 15 V
Input voltage range for IAG, SRG, ABG, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –15 V to 5 V
Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 30°C to 85°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 30°C to 85°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to VSS.
2-6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TC210
192- × 165-PIXEL CCD IMAGE SENSOR
SOCS009B – OCTOBER 1986 – REVISED MAY 1990
recommended operating conditions
Supply voltage at ADB
MIN
NOM
MAX
11
12
13
Substrate bias voltage
0
IAG
voltage VI†
Input voltage,
SRG
1.5
Intermediate level‡
–10
–5
2
Low level
–11
– 10
–9
1.5
2
2.5
Low level
–11
– 10
–9
Low level
Clock frequency, fclock
2.5
High level
Intermediate level‡
4
4.5
5
–3
–2.5
–2
– 7.5
–7
– 6.5
IAG
1.5
SRG
10
ABG
2
t1
Time interval, SRG↓ to IAG↑
t2
Time interval, IAG↑ to SRG transfer pulse ↑ (see Note 2)
tw1
tw2
V
V
High level
High level
ABG
2
UNIT
V
MHz
70
ns
0
ns
Pulse duration, IAG high
350
ns
Pulse duration, SRG transfer pulse high
350
ns
t3
Time interval, IAG↓ to SRG transfer pulse ↓
350
ns
t4
Time interval, SRG transfer pulse ↓ to SRG clock pulse ↑
Capacitive load
OUT
70
ns
12
pF
Operating free-air temperature, TA
–10
45
°C
† The algebraic convention, in which the least-positive (most negative) value is designated minimum, is used in this data sheet for clock voltage
levels.
‡ Adjustment is required for optimal performance.
NOTE 2: If t2 = 0, then t3 must be 700 ns minimum.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2-7
TC210
192- × 165-PIXEL CCD IMAGE SENSOR
SOCS009B – OCTOBER 1986 – REVISED MAY 1990
electrical characteristics over recommended operating range of supply voltage, TA = –10°C to 45°C
PARAMETER
Dynamic range (see Note 3)
MIN
Antiblooming disabled (see Note 4)
60
Antiblooming enabled
57
Charge conversion factor
TYP†
MAX
dB
µV/e
4.0
Charge transfer efficiency (see Note 5)
0.99990
0.99998
0.97
0.98
0.99
700
800
Signal response delay time, τ (see Note 6 and Figure 5)
25
Gamma (see Note 7)
Output resistance
1/f noise (5 kHz)
Noise voltage
ns
370
Random noise, f = 100 kHz
150
Rejection ratio at 7.16
7 16 MHz
From ADB to OUT (see Note 8)
19
From SRG to OUT (see Note 9)
37
Supply current
5
IAG
Input capacitance, Ci
Ω
nV/√Hz
70
Noise equivalent signal
UNIT
electrons
dB
10
mA
1600
SRG
25
ABG
780
pF
† All typical values are at TA = 25°C
NOTES: 3. Dynamic range is – 20 times the logarithm of the mean noise signal divided by the saturation output signal.
4. For this test, the antiblooming gate must be biased at the intermediate level.
5. Charge transfer efficiency is one minus the charge loss per transfer in the output register. The test is performed in the dark using
an electrical input signal.
6. Signal response delay time is the time between the falling edge of the SRG clock pulse and the output signal valid state.
7. Gamma (γ) is the value of the exponent in the equation below for two points on the linear portion of the transfer function curve (this
value represents points near saturation):
ǒ
Ǔ +ǒ
Exposure (2)
Exposure (1)
g
Ǔ
Output signal (2)
Output signal (1)
8. ADB rejection ratio is – 20 times the logarithm of the ac amplitude at the OUT divided by the ac amplitude at ADB.
9. SRG rejection ratio is – 20 times the logarithm of the ac amplitude at the OUT divided by the ac amplitude at SRG.
2-8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TC210
192- × 165-PIXEL CCD IMAGE SENSOR
SOCS009B – OCTOBER 1986 – REVISED MAY 1990
optical characteristics, TA = 25°C (unless otherwise noted)
PARAMETER
No IR filter
Sensitivity (see Note 10)
With IR filter
Saturation signal (see Note 12)
MIN
MAX
260
Measured at VU (see Note 11)
400
600
Antiblooming enabled
350
450
mV
5
Shuttered light
100
Output signal nonuniformity (1/2 saturation) (see Note 14)
10%
20%
1.5 × 105
Image-area well capacity
Dark current
TA = 21°C
electrons
nA/cm2
0.027
Dark signal (see Note 15)
Dark signal nonuniformity for entire field (see Note 16)
Modulation transfer function
UNIT
mV/lx
33
Antiblooming disabled
Strobe
Blooming overload ratio (see Note 13)
TYP
10
15
mV
4
15
mV
Horizontal
50%
Vertical
70%
NOTES: 10.
11.
12.
13.
14.
Sensitivity is measured at an integration time of 16.667 ms and a source temperature of 2856 K. A CM-500 filter is used.
VU is the output voltage that represents the threshold of operation of antiblooming. VU ≈ 1/2 saturation signal.
Saturation is the condition in which further increase in exposure does not lead to further increase in output signal.
Blooming overload ratio is the ratio of blooming exposure to saturation exposure.
Output signal nonuniformity is the ratio of the maximum pixel-to-pixel difference in output signal to the mean output signal for
exposure adjusted to give 1/2 the saturation output signal.
15. Dark-signal level is measured from the dummy pixels.
16. Dark-signal nonuniformity is the maximum pixel-to-pixel difference in a dark condition.
PARAMETER MEASUREMENT INFORMATION
VIH min
100%
90%
Intermediate Level
10%
VIL max
0%
tr
tf
tr = 220 ns, tf = 330 ns for IAG
tr = 115 ns, tf = 135 ns for ABG
Figure 3. Typical Clock Waveform for IAG and ABG
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2-9
TC210
192- × 165-PIXEL CCD IMAGE SENSOR
SOCS009B – OCTOBER 1986 – REVISED MAY 1990
PARAMETER MEASUREMENT INFORMATION
VIH min
100%
90%
10%
VIL max
0%
tr
tf
tr = 25 ns, tf = 30 ns
Figure 4. Typical Clock Waveform for SRG
1.5 V to 2.5 V
SRG
– 8.5 V
– 8.5 V to – 10 V
0%
OUT
90%
100%
CCD Delay
τ
10 ns
15 ns
Sample
and
Hold
Figure 5. SRG and OUT Waveforms
2-10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TC210
192- × 165-PIXEL CCD IMAGE SENSOR
SOCS009B – OCTOBER 1986 – REVISED MAY 1990
TYPICAL CHARACTERISTICS
VERTICAL MODULATION
TRANSFER FUNCTION
(BARS PARALLEL TO SERIAL REGISTER)
HORIZONTAL MODULATION
TRANSFER FUNCTION
(BARS PERPENDICULAR TO SERIAL REGISTER)
1
MTF – Modulation Transfer Function
MTF – Modulation Transfer Function
1
0.8
0.6
0.4
0.2
λ = 400 to 700-nm Monochromatic Light
VADB = 12 V
TA = 25°C
0
0.8
0.6
0.4
0.2
λ = 400 to 700-nm Monochromatic Light
VADB = 12 V
TA = 25°C
0
0
0.2
0.4
0.6
0.8
1
0
0.2
Normalized Spatial Frequency
0
6.3
12.5
18.8
25.0
0
31.3
7.3
0.8
1
14.6
21.8
29.1
36.4
Spatial Frequency – Cycles/mm
Figure 6
Figure 7
CCD SPECTRAL RESPONSIVITY
NOISE SPECTRUM OF OUTPUT AMPLIFIER
1
1000
100%
VADB = 12 V
TA = 25°C
Responsivity – A/W
VADB = 12 V
TA = 25°C
Hz
0.6
Normalized Spatial Frequency
Spatial Frequency – Cycles/mm
Noise – nV/
0.4
100
10
50%
20%
0.1
10%
5%
3%
2%
1
103
104
105
f – Frequency – Hz
106
107
0.01
300
500
700
900
1100
1300
Incident Wavelength – nm
Figure 8
Figure 9
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2-11
TC210
192- × 165-PIXEL CCD IMAGE SENSOR
SOCS009B – OCTOBER 1986 – REVISED MAY 1990
APPLICATION INFORMATION
1
7
GND
VCC
GND
CK
14
DC VOLTAGES
12 V
ADB
5V
VCC
– 10 V
VSS
2V
V
– 2.5 V
ABLVL
–5 V
IALVL
4V
VABG +
–6 V
VABG –
VCC
8
Master Oscillator
V
VSS
22 kΩ
TMS3473B
1
2
3
4
5
6
VCC 7
8
9
10
IALVL1
CLK
IAG
CMP
ABG
CBNK
GT1
CSYNC S/H
SRG
TRIG
S/H
User-Defined Timer
VABG+
IALVL
I/N
IAIN
ABIN
MIDSEL
SAIN
PD
GND
VABG+
VSS
ADB
VSS
IASR
ABSR
VCC
ABLVL
IAOUT
ABOUT
SAOUT
VCC
VABG–
20
19
18
17
16
15
14
13
12
11
47 kΩ
2.2 kΩ
ABLVL
TC210
1
ABG
IAG
5 kΩ
6
ADB
2
VSS
SRG
5
ADB
VABG–
Parallel Driver
ADB
3
ADB
OUT
4
2N3904
Image Sensor
4
500
SEL0OUT
VSS
GND
SEL0
PD
NC
SRG3IN
VCC
SRG2IN SRG3OUT
SRG1IN SRG2OUT
TRGIN SRG1OUT
NC
TRGOUT
SEL1OUT
VCC
VSS
SEL1
20
19
18
17
16
15
14
13
12
11
7 EL2020
6
2
SN28846
1
2
VCC 3
4
5
6
7
8
9
10
3
1 kΩ
VDD
VCC
TL1591
1
2
3
4
Serial Driver
ANLG VCC
ANLG IN
ANLG GND
ANLG OUT
DGTL VCC
DGTL IN
DGTL GND
SUB GND
Sample-and-Hold
OUT
SUPPORT CIRCUITS
DEVICE
PACKAGE
APPLICATION
FUNCTION
SN28846DW
20 pin small outline
Serial driver
Driver for SRG
TMS3473BDW
20 pin small outline
Parallel driver
Driver for IAG, ABG
TL1591CPS
8 pin small outline (EIAJ)
Sample and hold
Single-channel sample-and-hold IC
Figure 10. Typical Application Circuit Diagram
2-12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
8
7
6
5
S/H
TC210
192- × 165-PIXEL CCD IMAGE SENSOR
SOCS009B – OCTOBER 1986 – REVISED MAY 1990
MECHANICAL DATA
The TC210 package consists of a 5-mm (0.20-in) diameter ceramic and clear plastic molded base, glass window, and
a 6-lead frame. The glass window is sealed to the package by an epoxy adhesive. The package leads are configured
in a dual-in-line organization and fit into mounting holes with 1,27 mm (0.050 inch) center-to-center spacings.
2,64 (0.104)
25°
ÇÇÇÇ
ÇÇÇÇ
ÇÇÇÇ
ACTIVE
AREA
CL
25°
0,178 (0.007)
2,64 (0.104)
3
4
2
5
1
6
0,175 (0.007)
5,08 (0.200)
4,93 (0.194)
3,45 (0.136)
0,610 (0.24)
0,457 (0.018)
2,06 (0.081)
1,90 (0.075)
3,30 (0.130)
0,30 (0.012)
2,54 (0.100)
1,27 (0.050)
TYP
0,45 (0.018)
2,54 (0.100)
ALL LINEAR DIMENSIONS ARE IN MILLIMETERS AND PARENTHETICALLY IN INCHES
7/94
NOTES: A. Single dimensions are nominal.
B. The center of the package and the center of the image area are not coincident.
C. The distance from the top of the glass to the image sensor surface is typically 9 mm (0.035 inch). The glass is typically 0.020 inch
thick and has an index of refraction of 1.52.
D. Pin 2 is index pin.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2-13
SOCS009B – OCTOBER 1986 – REVISED MAY 1990
2-14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1998, Texas Instruments Incorporated