ETC AD8023AR-14

a
FEATURES
Drives 13 V Output
Drives Unlimited Capacitive Load
High Current Output Drive: 70 mA
Excellent Video Specifications (R L = 150 )
Gain Flatness 0.1 dB to 10 MHz
0.06% Differential Gain Error
0.02 Differential Phase Error
Power
Operates on 2.5 V to 7.5 V Supply
10.0 mA/Amplifier Max Power Supply Current
High Speed
250 MHz Unity Gain Bandwidth (3 dB)
1200 V/s Slew Rate
Fast Settling Time of 35 ns (0.1%)
High Speed Disable Function
Turn-Off Time 30 ns
Easy to Use
200 mA Short Circuit Current
Output Swing to 1 V of Rails
APPLICATIONS
LCD Displays
Video Line Driver
Broadcast and Professional Video
Computer Video Plug-In Boards
Consumer Video
RGB Amplifier in Component Systems
PRODUCT DESCRIPTION
The AD8023 is a high current output drive, high voltage output
drive, triple video amplifier. Each amplifier has 70 mA of output
current and is optimized for driving large capacitive loads. The
amplifiers are current feedback amplifiers and feature gain
flatness of 0.1 dB to 10 MHz while offering differential gain and
phase error of 0.06% and 0.02°.
VIN
VO
Figure 1. Pulse Response Driving a Large Load Capacitor,
CL = 300 pF, G = +3, RF = 750 Ω, RS = 16.9 Ω, RL = 10 kΩ
High Current Output,
Triple Video Amplifier
AD8023
PIN CONFIGURATION
14-Lead SOIC
DISABLE 1 1
14 OUT 2
DISABLE 2 2
13 –IN 2
DISABLE 3 3
+VS 4
12 +IN 2
AD8023
11 –VS
+IN 1 5
10 +IN 3
–IN 1 6
9 –IN 3
OUT 1 7
8 OUT 3
The AD8023 uses maximum supply current of 10.0 mA per
amplifier and runs on ± 2.5 V to ± 7.5 V power supply. The
outputs of each amplifier swing to within one volt of either
supply rail to easily accommodate video signals. The AD8023
is unique among current feedback op amps by virtue of its large
capacitive load drive with a small series resistor, while still
achieving rapid settling time. For instance, it can settle to 0.1% in
35 ns while driving 300 pF capacitance.
The bandwidth of 250 MHz along with a 1200 V/µs slew rate
make the AD8023 useful in high speed applications requiring
a single +5 V or dual power supplies up to ± 7.5 V. Furthermore, the AD8023 contains a high speed disable function for
each amplifier in order to power down the amplifier or high
impedance the output. This can then be used in video multiplexing applications. The AD8023 is available in the industrial temperature range of –40°C to +85°C.
VIN
VO
Figure 2. Output Swing Voltage,
RL = 150 Ω; VS = ± 7.5 V, G = +10
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2000
AD8023–SPECIFICATIONS (@ T = +25C, V = 7.5, C
A
S
LOAD
= 10 pF, RLOAD = 150 , unless otherwise noted)
Model
Conditions
DYNAMIC PERFORMANCE
Bandwidth (3 dB)
Bandwidth (0.1 dB)
Slew Rate
Settling Time to 0.1%
NOISE/HARMONIC PERFORMANCE
Total Harmonic Distortion
Input Voltage Noise
Input Current Noise
Differential Gain (RL = 150 Ω)
Differential Phase (RL = 150 Ω)
DC PERFORMANCE
Input Offset Voltage
Offset Drift
Input Bias Current (–)
Input Bias Current (+)
Open-Loop Transresistance
VS
OUTPUT CHARACTERISTICS
Output Voltage Swing
RL = 1 kΩ
RL = 150 Ω
POWER SUPPLY
Operating Range
Units
125
7
1200
MHz
MHz
V/µs
30
ns
fC = 5 MHz, RL = 150 Ω, VO = 2 p-p
f = 10 kHz
f = 10 kHz (–IIN)
f = 3.58 MHz, G = +2, RFB = 750 Ω
f = 3.58 MHz, G = +2, RFB = 750 Ω
–72
2.0
14
0.06
0.02
dBc
nV/√Hz
pA/√Hz
%
Degrees
TMIN to TMAX
–5
TMIN to TMAX
TMIN to TMAX
–45
–25
67
50
TMIN to TMAX
TMIN to TMAX
50
VOL–VEE
VCC–VOH
VOL–VEE
VCC–VOH
Output Current
Short-Circuit Current
Capacitive Load Drive
MATCHING CHARACTERISTICS
Dynamic
Crosstalk
DC
Input Offset Voltage
–Input Bias Current
AD8023A
Typ
Max
RFB = 750 Ω No Peaking, G = +3
No Peaking, G = +3
5 V Step
0 V to ± 6 V (6 V Step)
CLOAD = 300 pF
RLOAD > 1 kΩ, RFB = 750 Ω
TA = +25°C to +70°C, RS = 16.9 Ω
TMIN to TMAX
INPUT CHARACTERISTICS
Input Resistance
+Input
–Input
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
Input Offset Voltage
–Input Current
+Input Current
Min
50
G = +2, f = 5 MHz
5
45
25
Single Supply
Dual Supply
kΩ
Ω
pF
V
56
0.2
5
dB
µA/V
µA/V
0.8
0.8
1.0
1.0
70
300
1000
0.3
3
+4.2
± 2.1
Quiescent Current/Amplifier
TMIN to TMAX
Power-Down
–2–
mV
µV/°C
µA
µA
kΩ
kΩ
100
75
2
± 6.0
1.0
1.0
1.3
1.3
70
–5
–10
Powered by ICminer.com Electronic-Library Service CopyRight 2003
2
2
15
5
111
111
V
V
V
V
mA
mA
pF
dB
5
10
mV
µA
+15
± 7.5
6.2
7.0
10.0
V
V
mA
mA
1.3
4.0
mA
REV. A
AD8023
Model
Conditions
POWER SUPPLY (Continued)
Power Supply Rejection Ratio
Input Offset Voltage
–Input Current
+Input Current
VS
Min
AD8023A
Typ
Max
VS = ± 2.5 V to ± 7.5 V
54
DISABLE CHARACTERISTICS
Off Isolation
Off Output Capacitance
Turn-On Time
Turn-Off Time
Switching Threshold
f = 6 MHz
G = +1
RL = 150 Ω
VTH – VEE
Units
76
0.03
0.07
dB
dB
µA/V
µA/V
–70
12
50
30
1.6
dB
pF
ns
ns
V
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS *
Maximum Power Dissipation
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 15.5 V Total
Internal Power Dissipation
Small Outline (R) . . . . 1.0 Watts (Observe Derating Curves)
Input Voltage (Common Mode) . . . . . . . . . . . . . . . . . . . . ± VS
Differential Input Voltage . . . . . . . . . . . . . . . . ± 3 V (Clamped)
Output Voltage Limit
Maximum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +VS
Minimum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –VS
Output Short Circuit Duration
. . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves
Storage Temperature Range
R Package . . . . . . . . . . . . . . . . . . . . . . . . –65°C to +125°C
Operating Temperature Range
AD8023A . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300°C
The maximum power that can be safely dissipated by the AD8023
is limited by the associated rise in junction temperature. The
maximum safe junction temperature for the plastic encapsulated
parts is determined by the glass transition temperature of the
plastic, about 150°C. Temporarily exceeding this limit may
cause a shift in parametric performance due to a change in the
stresses exerted on the die by the package. Exceeding a junction
temperature of 175°C for an extended period can result in
device failure.
While the AD8023 is internally short circuit protected, this may
not be enough to guarantee that the maximum junction temperature is not exceeded under all conditions. To ensure proper
operation, it is important to observe the derating curves.
It must also be noted that in (noninverting) gain configurations
(with low values of gain resistor), a high level of input overdrive
can result in a large input error current, which may result in a
significant power dissipation in the input stage. This power
must be included when computing the junction temperature rise
due to total internal power.
*Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
ORDERING GUIDE
AD8023AR
AD8023ARREEL
AD8023ARREEL7
AD8023ACHIPS
Package
Description
MAXIMUM POWER DISSIPATION – Watts
Model
Temperature
Range
2.5
Package
Option
–40°C to +85°C 14-Lead Plastic SOIC R-14
–40°C to +85°C 13" Tape and Reel
R-14
–40°C to +85°C 7" Tape and Reel
R-14
–40°C to +85°C Die
TJ = +150C
2.0
1.5
14-LEAD SOIC
1.0
0.5
–50 –40 –30 –20 –10 0 10 20 30 40 50 60 70
AMBIENT TEMPERATURE – C
80 90
Figure 3. Maximum Power Dissipation vs. Ambient
Temperature
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD8023 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
REV. A Electronic-Library Service CopyRight 2003
Powered by ICminer.com
–3–
WARNING!
ESD SENSITIVE DEVICE
AD8023
METALIZATION PHOTO
Contact factory for latest dimensions.
Dimensions shown in inches and (mm).
–IN1
6
+IN
5
+VS
4
DISABLE 3
3
DISABLE 2
2
DISABLE 1
1
7
OUT 1
0.0634
(1.61)
14
OUT 2
8
OUT 3
–IN 2
13
–IN3
9
+IN 3
10
–VS
11
+IN 2
12
0.0713
(1.81)
8
14
7
13
VS = 7.5V
OUTPUT VOLTAGE SWING – V p-p
COMMON-MODE VOLTAGE RANGE – Volts
Typical Performance Characteristics
6
5
4
3
2
1
0
2
3
4
5
6
SUPPLY VOLTAGE – Volts
7
11
10
9
8
7
6
10
8
Figure 4. Input Common-Mode Voltage Range vs.
Supply Voltage
Powered by ICminer.com Electronic-Library Service CopyRight 2003
12
100
1k
LOAD RESISTANCE – 10k
Figure 5. Output Voltage Swing vs. Load Resistance
–4–
REV. A
AD8023
35
25
TA = +25C
INPUT BIAS CURRENT – A
TOTAL SUPPLY CURRENT – mA
30
20
15
10
25
20
–IB
15
10
+IB
5
0
5
1
2
3
4
6
5
7
SUPPLY VOLTAGE – Volts
8
0
–50 –40 –30 –20 –10
9
0 10 20 30 40 50 60 70 80 90 100
TEMPERATURE – C
Figure 9. Input Bias Current vs. Temperature
Figure 6. Total Supply Current vs. Supply Voltage
1
16
14
INPUT OFFSET VOLTAGE – mV
OUTPUT VOLTAGE SWING – Vp-p
TA = +25C
12
SWING
NO LOAD
10
8
SWING
RL = 150
6
VS = 2.5V
0
VS = 7.5V
–1
4
2
2
3
4
5
6
SUPPLY VOLTAGE – Volts
7
–2
–40 –30 –20 –10
8
0
10 20 30 40 50
TEMPERATURE – C
60
70
80
90
Figure 10. Input Offset Voltage vs. Temperature
Figure 7. Output Voltage Swing vs. Supply Voltage
CLOSED-LOOP OUTPUT RESISTANCE – V
24
TOTAL SUPPLY CURRENT – mA
VS = 7.5V
22
20
18
16
VS = 2.5V
14
12
10
–50 –40 –30 –20 –10 0 10 20 30 40 50 60 70 80 90 100
TEMPERATURE – C
G = +2
31
VS = 2.5V
10
VS = 7.5V
3.1
1
0.31
0.1
1
10
FREQUENCY – MHz
100
300
Figure 11. Closed-Loop Output Resistance vs. Frequency
Figure 8. Total Supply Current vs. Temperature
REV. A Electronic-Library Service CopyRight 2003
Powered by ICminer.com
100
–5–
AD8023
200
90
200
100
COMMON-MODE REJECTION – dB
100
+I NOISE
10
10
CURRENT NOISE – pAHz
VOLTAGE NOISE – nVHz
– I NOISE
V NOISE
R
80
R
VCM
70
R
VS = 7.5V
60
R
50
40
VS = 2.5V
30
20
10
1
0.1
1
0
1
0
100
10
FREQUENCY – kHz
Figure 12. Input Current and Voltage Noise vs. Frequency
10
FREQUENCY – MHz
100
200
Figure 15. Common-Mode Rejection vs. Frequency
70
450
POWER SUPPLY REJECTION – dB
SHORT CIRCUIT CURRENT – mA
VS = 7.5V
400
SOURCE
350
SINK
300
250
–50 –40 –30 –20 –10 0 10 20 30 40 50 60 70 80 90 100
TEMPERATURE – C
60
VS = 2.5V (+PSRR)
50
40
30
20
VS = 2.5V (–PSRR)
VS = 7.5V (–PSRR)
10
0
1
10
FREQUENCY – MHz
100
Figure 16. Power Supply Rejection Ratio vs. Frequency
Figure 13. Short Circuit Current vs. Temperature
10k
0
–10
G = +1
VS = 7.5V
1k
HARMONIC DISTORTION – dBc
OUTPUT RESISTANCE – VS = 7.5V (+PSRR)
100
10
–20
–30
–40
–50
–60
–70
–80
1
10
FREQUENCY – Hz
100
–90
1
200
2ND
3RD
10
FREQUENCY – MHz
100
Figure 17. Harmonic Distortion vs. Frequency, RL = 150 Ω
Figure 14. Output Resistance vs. Frequency,
Disabled State
Powered by ICminer.com Electronic-Library Service CopyRight 2003
G = +1
VS = 7.5V
VO = 2V p-p
–6–
REV. A
AD8023
TRANSIMPEDANCE – 100k
10k
VIN
1k
100
VO
10
1k
10k
100k
1M
10M
FREQUENCY – Hz
100M
1G
Figure 21. Small Signal Pulse Response, Gain = +1,
(RF = 2 kΩ, RL = 150 Ω, VS = ± 7.5 V)
Figure 18. Open-Loop Transimpedance vs. Frequency
1600
1600
G = –1
G = +2
1400
1400
G = –1
G = +2
1200
SLEW RATE – V/s
SLEW RATE V/s
1200
G = +1
1000
G = +10
800
600
1000
800
G = +1
600
G = +10
400
400
200
200
0
2
0
0
1
2
3
4
5
6
3
4
5
6
SUPPLY VOLTAGE – V
7
8
OUTPUT VOLTAGE STEP – V p-p
Figure 22. Maximum Slew Rate vs. Supply Voltage
Figure 19. Slew Rate vs. Output Step Size
VIN
VIN
VO
VO
Figure 20. Large Signal Pulse Response,
Gain = +1, (RF = 2 kΩ, RL = 150 Ω, VS = ± 7.5 V)
REV. A Electronic-Library Service CopyRight 2003
Powered by ICminer.com
Figure 23. Large Signal Pulse Response,
Gain = +10, (RF = 274 Ω, RL = 150 Ω, VS = ± 7.5 V)
–7–
AD8023
+1
VS = 7.5V
GAIN
0
–1
VS = 2.5V
–2
PHASE
–3
VS = 7.5V
0
–4
VS = 2.5V
–5
–90
G = +10
RL = 150
–6
–7
–180
–8
1
10
FREQUENCY – MHz
100
0
Figure 24. Closed-Loop Gain and Phase vs. Frequency,
G = +10, RL = 150 Ω
VS = 7.5V
–1
–2
VS = 2.5V
–3
–4
PHASE
VS = 7.5V
0
–5
VS = 2.5V
–6
–7
–90
G = +1
RL = 150
–8
–9
1
500
GAIN
–180
10
FREQUENCY – MHz
100
PHASE SHIFT – Degrees
CLOSED-LOOP GAIN (NORMALIZED) – dB
+1
PHASE SHIFT – Degrees
CLOSED-LOOP GAIN (NORMALIZED) – dB
+2
500
Figure 27. Closed-Loop Gain and Phase vs. Frequency,
G = –1, RL = 150 Ω
0
GAIN
–1
–2
VS = 2.5V
–3
VIN
VS = 7.5V 0
–4
PHASE
–5
–90
–6
–7
–180
–8
–9
1
10
FREQUENCY – MHz
100
PHASE SHIFT – Degrees
CLOSED-LOOP GAIN (NORMALIZED) – dB
+1
VO
400
Figure 25. Closed-Loop Gain and Phase vs. Frequency,
G = +1, RL = 150 Ω
Figure 28. Small Signal Pulse Response,
Gain = +10, (RF = 274 Ω, RL = 150 Ω, VS = ± 7.5 V)
VIN
V IN
VO
VO
Figure 26. Large Signal Pulse Response,
Gain = –1, (RF = 750 Ω, RL = 150 Ω, VS = ± 7.5 V)
Powered by ICminer.com Electronic-Library Service CopyRight 2003
Figure 29. Small Signal Pulse Response,
Gain = –1, (RF = 750 Ω, RL = 150 Ω, VS = ± 7.5 V)
–8–
REV. A
AD8023
where:
–1
VS = 7.5V
–2
–3
PHASE
–4
VS = 2.5V
0
–5
–6
–90
G = –10
RL = 150
–7
VS = 2.5V
–180
–8
–9
1
G
1+ SCT (RF + Gn rin )
CT = transcapacitance 1 pF
RF = feedback resistor
G = ideal closed loop gain

RF 
Gn = 1 + R  = noise gain

G
rin = inverting input resistance 150 Ω
ACL = closed loop gain
ACL GAIN
0
10
FREQUENCY – MHz
100
PHASE SHIFT – Degrees
CLOSED-LOOP GAIN (NORMALIZED) – dB
+1
The –3 dB bandwidth is determined from this model as:
1
f3 2 π C (R + Gn rin )
T
F
500
This model will predict –3 dB bandwidth to within about
10% to 15% of the correct value when the load is 150 Ω and
VS = ±7.5 V. For lower supply voltages there will be a slight
decrease in bandwidth. The model is not accurate enough to
predict either the phase behavior or the frequency response
peaking of the AD8023.
Figure 30. Closed-Loop Gain and Phase vs. Frequency,
G = –10, RL = 150 Ω
General
The AD8023 is a wide bandwidth, triple video amplifier that
offers a high level of performance on less than 9.0 mA per
amplifier of quiescent supply current. The AD8023 achieves
bandwidth in excess of 200 MHz, with low differential gain and
phase errors and high output current making it an efficient video
amplifier.
It should be noted that the bandwidth is affected by attenuation
due to the finite input resistance. Also, the open-loop output
resistance of about 6 Ω reduces the bandwidth somewhat when
driving load resistors less than about 150 Ω. (Bandwidths will
be about 10% greater for load resistances above a couple
hundred ohms.)
The AD8023’s wide phase margin coupled with a high output
short circuit current make it an excellent choice when driving
any capacitive load up to 300 pF.
It is designed to offer outstanding functionality and performance
at closed-loop inverting or noninverting gains of one or greater.
Table I. –3 dB Bandwidth vs. Closed-Loop Gain and Feedback
Resistor, RL = 150 (SOIC)
Choice of Feedback and Gain Resistors
VS – Volts
± 7.5
Because it is a current feedback amplifier, the closed-loop bandwidth of the AD8023 may be customized using different values
of the feedback resistor. Table I shows typical bandwidths at
different supply voltages for some useful closed-loop gains when
driving a load of 150 Ω.
± 2.5
The choice of feedback resistor is not critical unless it is desired
to maintain the widest, flattest frequency response. The resistors
recommended in the table (chip resistors) are those that will
result in the widest 0.1 dB bandwidth without peaking. In
applications requiring the best control of bandwidth, 1%
resistors are adequate. Resistor values and widest bandwidth
figures are shown. Wider bandwidths than those in the table can
be attained by reducing the magnitude of the feedback resistor
(at the expense of increased peaking), while peaking can be
reduced by increasing the magnitude of the feedback resistor.
RF – Ohms
2000
750
300
750
250
2000
1000
300
750
250
BW – MHz
460
240
50
150
60
250
90
30
95
50
Driving Capacitive Loads
When used in combination with the appropriate feedback
resistor, the AD8023 will drive any load capacitance without
oscillation. The general rule for current feedback amplifiers is
that the higher the load capacitance, the higher the feedback
resistor required for stable operation. Due to the high open-loop
transresistance and low inverting input current of the AD8023,
the use of a large feedback resistor does not result in large closedloop gain errors. Additionally, its high output short circuit current
makes possible rapid voltage slewing on large load capacitors.
Increasing the feedback resistor is especially useful when driving
large capacitive loads as it will increase the phase margin of the
closed-loop circuit. (Refer to the Driving Capacitive Loads
section for more information.)
For the best combination of wide bandwidth and clean pulse
response, a small output series resistor is also recommended.
Table II contains values of feedback and series resistors which
result in the best pulse responses. Figure 28 shows the AD8023
driving a 300 pF capacitor through a large voltage step with
virtually no overshoot. (In this case, the large and small signal
pulse responses are quite similar in appearance.)
To estimate the –3 dB bandwidth for closed-loop gains of 2 or
greater, for feedback resistors not listed in the following table,
the following single pole model for the AD8023 may be used:
REV. A Electronic-Library Service CopyRight 2003
Powered by ICminer.com
Gain
+1
+2
+10
–1
–10
+1
+2
+10
–1
–10
–9–
AD8023
RF
+VS
1.0F
0.1F
RG
VIN
4
AD8023
11
VIN
15
1.0F
RS
VO
CL
0.1F
RT
–VS
VO
Figure 31. Circuit for Driving a Capacitive Load
Table II. Recommended Feedback and Series Resistors vs.
Capacitive Load and Gain
CL – pF
RF – Ohms
RS – Ohms
G=2
G≥3
20
50
100
200
300
≥500
2k
2k
2k
3k
3k
3k
0
10
15
10
10
10
0
10
15
10
10
10
VIN
VO
Figure 32. Pulse Response Driving a Large Load Capacitor.
CL = 300 pF, G = +3, RF = 750 Ω, RS = 16.9 Ω, RL = 10 kΩ
Overload Recovery
Figure 33. 50% Overload Recovery, Gain = +10,
(RF = 300 Ω, RL = 1 kΩ, VS = ± 7.5 V)
As noted in the warning under Maximum Power Dissipation, a
high level of input overdrive in a high noninverting gain circuit
can result in a large current flow in the input stage. Though this
current is internally limited to about 30 mA, its effect on the
total power dissipation may be significant.
Disable Mode Operation
Pulling the voltage on any one of the Disable pins about 1.6 V up
from the negative supply will put the corresponding amplifier
into a disabled, powered down, state. In this condition, the
amplifier’s quiescent current drops to about 1.3 mA, its output
becomes a high impedance, and there is a high level of isolation
from input to output. In the case of a gain of two line driver for
example, the impedance at the output node will be about the
same as for a 1.5 kΩ resistor (the feedback plus gain resistors)
in parallel with a 12 pF capacitor.
Leaving the Disable pin disconnected (floating) will leave the
corresponding amplifier operational, in the enabled state. The
input impedance of the disable pin is about 25 kΩ in parallel
with a few picofarads. When driven to 0 V, with the negative
supply at –7.5 V, about 100 µA flows into the disable pin.
When the disable pins are driven by complementary output
CMOS logic, on a single 5 V supply, the disable and enable
times are about 50 ns. When operated on dual supplies, level
shifting will be required from standard logic outputs to the
Disable pins. Figure 33 shows one possible method, which
results in a negligible increase in switching time.
The three important overload conditions are: input commonmode voltage overdrive, output voltage overdrive, and input
current overdrive. When configured for a low closed-loop gain,
this amplifier will quickly recover from an input common-mode
voltage overdrive; typically in under 25 ns. When configured for
a higher gain, and overloaded at the output, the recovery time
will also be short. For example, in a gain of +10, with 50%
overdrive, the recovery time of the AD8023 is about 20 ns (see
Figure 31). For higher overdrive, the response is somewhat
slower. For 100% overdrive, (in a gain of +10), the recovery
time is about 80 ns.
+5
VI
+7.5V
15k
TO DISABLE PIN
4k
10k
–7.5V
V I HIGH => AMPLIFIER ENABLED
V I LOW => AMPLIFIER DISABLED
Figure 34. Level Shifting to Drive Disable Pins on Dual
Supplies
The AD8023’s input stages include protection from the large
differential input voltages that may be applied when disabled.
Internal clamps limit this voltage to about ±3 V. The high input to
output isolation will be maintained for voltages below this limit.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
–10–
REV. A
AD8023
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
0.3444 (8.75)
0.3367 (8.55)
0.1574 (4.00)
0.1497 (3.80)
14
8
1
7
PIN 1
0.0098 (0.25)
0.0040 (0.10)
0.0500
(1.27)
BSC
0.0688 (1.75)
0.0532 (1.35)
0.0192 (0.49)
0.0138 (0.35)
0.0099 (0.25)
0.0075 (0.19)
0.0196 (0.50)
x 45°
0.0099 (0.25)
8°
0°
0.0500 (1.27)
0.0160 (0.41)
PRINTED IN U.S.A.
SEATING
PLANE
0.2440 (6.20)
0.2284 (5.80)
C3137–0–3/00 (rev. A)
14-Lead Plastic SOIC
(R-14)
REV. A Electronic-Library Service CopyRight 2003
Powered by ICminer.com
–11–