ENH104V2-380/450/600 Panelview Enhancing the Vision ENH104V2-380/450/600 Color TFT-LCD Module Features SPECIFICATIONS GENERAL DESCRIPTION ITEM Panelview provides optically enhanced solutions to the standard Optrex AA104VB05 color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module. The first enhancement is an index matching (IM) film lamination to the front surface of the display polarizer. The IM film is a contrast enhancement benefit and is available in two surface treatments IM/Clear and IM/110 (a 10% diffusion). The second enhancement is the incorporation of a reflective polarizer (RP) to improve brightness by up to 40%. The third enhancement is the incorporation of an enhanced light guide (ELG) to improve brightness by up to 35%. The resultant brightness levels are shown in the Specifications below. SPECIFICATION Display Area (mm) 211.2 (H) x 158.4 (V) (10.39-inch diagonal) Number of Dots 640 x 3 (H) x 480 (V) Pixel Pitch (mm) 0.33 (H) x 0.33 (V) Color Pixel Arrangement RGB vertical stripe Display Mode normally white Number of Color 260 K Wide Viewing Angle Technology Optical compensation film Optimum Viewing Angle (Contrast ratio) 12 oclock Brightness (cd/m2) ENH104V2-380 (IM only) ENH104V2-450 (IM, RP) ENH104V2-600 (IM, RP, ELG) The module is composed of an LCD panel, driver ICs, control circuit, and backlight unit. Module Size (mm) 380 450 600 243.0 (W) x 181.6 (H) x 12.2 (D) By applying 6 bit digital data 640 x 480, 260K-color images are displayed on the 10.4" diagonal screen. Module Mass (g) Backlight Unit CCFL, 2-tubes, replaceable Input power voltage is single 3.3 / 5.0V for LCD driving. Both 3.3V-CMOS and 5.0V-CMOS level voltage are acceptable for logic input voltage. Surface Treatment IM/Clear (glossy) or IM/110 and hardcoat 3H 530 Characteristic value without any note is typical value. The LCD product described in this specification is designed and manufactured for the standard use in office automation equipment, instrumentation, communication equipment, automation, point of sale, etc. Inverter for backlight is not included in this module. General specifications are summarized in the following table: Panelview assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. Panelview does assume the responsibility for the warranty of the enhanced product. ABSOLUTE MAXIMUM RATINGS ITEM SYMBOL MIN. MAX. Power Supply Voltage for LCD VCC -0.3 6.5 UNIT V Logic Input Voltage VI 0 6.5 V Lamp Voltage Lamp Current VL IL 0 0 2000 10.0 Vrms mArms Lamp Frequency FL 80 kHz Operation Temperature (1) TOP 0 50 °C Storage Temperature (1) TSTG -20 60 °C £ Note 1. TOP,TSTG 40°C : 90%RH max. without condensation TOP,TSTG > 40°C : Absolute humidity shall be less than the value of 90%RH at 40°C without condensation. Original specifications created by Sharp. August 2003 Rev. 0 ENH104V2-380/450/600 1 Panelview (503) 690-2460 www.whiteedc.com Panelview is a subsidiary of White Electronic Designs Corporation ENH104V2-380/450/600 Panelview Enhancing the Vision ELECTRICAL CHARACTERISTICS TFT- LCD A MBIENT TEMPERATURE : TA = 25°C ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks Power Supply 3.3 V powered VCC 3.0 3.3 3.6 V (A), (D) Voltage for LCD 5.0 V powered VCC 4.75 5.0 5.25 V (A), (D) Power Supply 3.3 V powered I CC 220 380 mA VCC=3.3 V (B) Current for LCD 5.0 V powered Permissive Input Ripple Voltage I CC 150 280 mA VCC=5.0 V (B) V RP 100 mVp-p VCC=+3.3 V/5.0 V Logic Input High VIH 2.0 5.25 V Voltage Low VIL 0 0.8 V BACKLIGHT TA=25°C ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks Lamp Voltage VL 580 Vrms IL=6.0mArms Lamp Current IL 3.0 6.0 7.0 mArms (1) Lamp Frequency FL 40 80 kHz (2) 810 Vrms Starting Lamp Voltage Ta=25°C Ta=0°C VS IL=3.0mArms Lamp Life Time IL=6.0mArms LT IL=7.0mArms 1000 Vrms 50000 50000 h 40000 50000 h 30000 40000 h (3), (4) Notes: 1. Lamp Current measurement method (The current meter is inserted in low voltage line.) A CTL CTH LCD Module A CTL Inverter Power Supply CTH 2. Lamp frequency of inverter may produce interference with horizontal synchronous frequency, and this may cause horizontal beat on the display. Therefore, please adjust lamp frequency, and keep inverter as far from module as possible or use electronic shielding between inverter and module to avoid the interference. 3. Lamp life time is defined as the time either when the brightness becomes 50% of the initial value, or when the starting lamp voltage does not meet the value specified in this table. 4. The life time of the backlight depends on the ambient temperature. The life time will decrease under low/high temperature. Original specifications created by Sharp. Panelview Hillsboro, OR (503) 690-2460 Panelview is a subsidiary of White Electronic Designs Corporation 2 ENH104V2-380/450/600 Panelview Enhancing the Vision Notes: A. Power and signals sequence: t1 10 ms 400 ms 0 < t2 50 ms 200 ms 0 < t3 50 ms 0 t7 0 < t4 50 ms £ £ £ £ £ £ t5 £ t6 VCC 0.9VCC 0.9VCC Data 0.1VCC 0.1VCC 0.1VCC t1 t2 t4 t3 t5 Backlight t6 t7 Data: RGB DATA, DCLK, HD, VD, DENA VCC-dip conditions: (a) 3.3 V powered 1. When 2.4 V VCC < 3.0 V, td 10 ms 2. When VCC < 2.4 V VCC-dip conditions should also follow the power and signals sequence. £ 3.0 V VCC 2.4 V £ td Original specifications created by Sharp. 3 Panelview (503) 690-2460 www.whiteedc.com Panelview is a subsidiary of White Electronic Designs Corporation ENH104V2-380/450/600 Panelview Enhancing the Vision (b) 5.0 V powered 1. When 3.6 V VCC < 4.5 V, td 10 ms 2. When VCC < 3.6 V VCC-dip conditions should also follow the power and signals sequence. £ £ td B) Typical current condition: 64- gray- bar-pattern 480 line mode VCC = + 3.3/5.0 V, fH=31.6kHz, fV=60HZ, fCLK= 25MHz Original specifications created by Sharp. Panelview Hillsboro, OR (503) 690-2460 Panelview is a subsidiary of White Electronic Designs Corporation 4 4.5 V 3.6 V VCC ENH104V2-380/450/600 Panelview Enhancing the Vision INTERFACE PIN CONNECTION CN 1(INTERFACE SIGNAL) USED CONNECTOR: DF9B-31P-1V(HIROSE)/CORRESPONDING CONNECTOR: DF9B-31S-1V(HIROSE) Pin No. Symbol 1 GND Function 2 DCLK 3 HD Horizontal sync signal 4 VD Vertical sync signal 5 GND 6 R0 Red data signal (LSB) 7 R1 Red data signal 8 R2 Red data signal 9 R3 Red data signal 10 R4 Red data signal 11 R5 Red data signal (MSB) 12 GND Clock signal for sampling catch data signal 13 G0 Green data signal (LSB) 14 G1 Green data signal 15 G2 Green data signal 16 G3 Green data signal 17 G4 Green data signal 18 G5 Green data signal (MSB) 19 GND 20 B0 Blue data signal (LSB) 21 B1 Blue data signal 22 B2 Blue data signal 23 B3 Blue data signal 24 B4 Blue data signal 25 B5 Blue data signal (MSB) 26 GND 27 DENA 28 VCC 29 VCC 3.3 / 5.0 V Power Supply 30 TEST This pin should be open. Test signal output for only internal test use. 31 SC Data enable signal(to settle the viewing area) 3.3 / 5.0 V Power Supply Scan direction Control. (GND or Open:Normal, High:Reverse) Notes: 1. The shielding case is connected with GND 2. See; Timing Chart (p. 7) CN 2 , CN 3 (BACKLIGHT) BACKLIGHT-SIDE CONNECTOR: BHR-02(8.0)VS-1N(JST)/INVERTER-SIDE CONNECTOR: SM02(8.0)B-BHS(JST) Pin No. Symbol Function 1 CTH VBLH High Voltage 3 CTL VBLL Low Voltage Note VBLH-VBLL=VL Original specifications created by Sharp. 5 Panelview (503) 690-2460 www.whiteedc.com Panelview is a subsidiary of White Electronic Designs Corporation ENH104V2-380/450/600 Panelview Enhancing the Vision INTERFACE TIMING TIMING SPECIFICATIONS ITEM SYMBOL MIN. TYP. MAX. UNIT Frequency fCLK 25 29 MHz DCLK Period t CLK 34.5 40 ns (1) (4) Low Width tWCL 12 ns High Width tWCH 12 ns DATA (1) (R,G, Set up time tDS 5 ns Hold time tDH 5 ns Horizontal Active Time tHA 640 640 640 tCLK Horizontal Front Porch tHFP 10 16 tCLK Horizontal Back Porch t HBP 2 144 tCLK B,DENA HD, VD) DENA (3) HD (2) (4) Vertical Active Time tVA 480 480 480 tH Vertical Front Porch t VFP 1 12 tH Vertical Back Porch tVBP 2 33 tH fH 27 31.6 38 kHz Frequency tH 26.3 31.6 37.0 ms Low Width Period t WHL 5 96 tCLK VD Frequency fV 55 60 70 Hz (2) Period tV 14.3 16.7 18.2 ms t WVL 3 tH Low Width Note: 1. DATA is latched at fall edge of DCLK in this specification. 2. Polarities of HD and VD are negative in this specification. 3. DENA (Data Enable) should always be positive polarity as shown in the timing specification. 4. DCLK should appear during all invalid period, and HD should appear during invalid period of frame cycle. PIXEL TIMING CHART t CLK t WCH t WCL DCLK 2.0V 0.8V t DS t DH DATA (RGB), 2.0V DENA, HD, VD 0.8V Original specifications created by Sharp. Panelview Hillsboro, OR (503) 690-2460 Panelview is a subsidiary of White Electronic Designs Corporation 6 ENH104V2-380/450/600 Panelview Enhancing the Vision HORIZONTAL TIMING CHART DCLK First Data DATA (RGB) Invalid Data 1 2 3 639 640 Invalid Data Last Data t HFP t HBP t HA DENA t H =1/f H t WHL HD VERTICAL TIMING CHART HD LINE DATA Invalid Data t VFP 1 2 3 t VBP 479 480 Invalid Data t VA DENA t V=1/f V t WVL VD Original specifications created by Sharp. 7 Panelview (503) 690-2460 www.whiteedc.com Panelview is a subsidiary of White Electronic Designs Corporation ENH104V2-380/450/600 Panelview Enhancing the Vision COLOR DATA ASSIGNMENT R DATA COLOR INPUT DATA R5 R4 R3 R2 G DATA R1 MSB R0 G5 G4 G3 G2 B DATA G1 LSB MSB G0 B5 B4 B3 B2 B1 LSB MSB B0 LSB BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RED (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 GREEN (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 BASIC BLUE (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 COLOR CYAN 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 MAGENTA 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 YELLOW 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 WHITE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 RED (0) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RED (1) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 RED (2) 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 RED (62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 RED (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 GREEN (0) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GREEN (1) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 RED (2) 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 GREEN (62) 1 1 1 1 1 0 1 1 1 1 1 0 0 0 0 0 0 0 GREEN (63) 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 BLUE (0) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 BLUE (1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 BLUE (2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 BLUE (62) 1 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 1 0 BLUE (63) 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 RED GREEN BLUE Notes: 1. Definition of gray scale Color (n) n indicates gray scale level. 2. Data 1: High , 0: Low Higher n means brighter level. Original specifications created by Sharp. Panelview Hillsboro, OR (503) 690-2460 Panelview is a subsidiary of White Electronic Designs Corporation 8 ENH104V2-380/450/600 Panelview Enhancing the Vision BLOCK DIAGRAM Timing signal Display data Timing G1 I/F Connector G2 TFT-LCD S1920 S1919 Power Supply Circuit S2 G480 S1 Power Driver (gate) Converter Driver(source) BACKLIGHT CCFL CN2, 3 1 3 Original specifications created by Sharp. 9 Panelview (503) 690-2460 www.whiteedc.com Panelview is a subsidiary of White Electronic Designs Corporation ENH104V2-380/450/600 Panelview Enhancing the Vision MECHANICAL SPECIFICATIONS FRONT VIEW 243 ±0.5 8 5 ±0.3 BHR-02(8.0)VS-1N 235 ±0.3 4.2 12.4 215.4 (Bezel Opening) 14.5 211.2 (Display Area) 10 5 7.5 2.5 ±0.2 60 ±10 2 - Ø 3.5 90.8 17 ±0.3 4 2-R 1.75 2.5 ±0.2 2.9 60 8.6 161.8 (Bezel Opening) 132.6 ±03 Display Center 158.4 (Display Area) 181.6 ±0.5 166.6 ±0.3 5 ±0.3 DF9B-31P-1V 10 5 55 2.9 4 60 ±10 90 12.2 ±0.5 124.3 BHR-02(8.0)VS-1N REAR VIEW 12 2.35 Note: Tolerance is ±0.5mm unless noted. Original specifications created by Sharp. Panelview Hillsboro, OR (503) 690-2460 Panelview is a subsidiary of White Electronic Designs Corporation 10 ENH104V2-380/450/600 Panelview Enhancing the Vision SCANNING DIRECTION SC : High D(1,1) D(640,1) CN2 D(640,480) D(1,480) CN3 SC : GND or Open D(1,1) D(640,1) CN3 CN2 D(1,480) D(640,480) Original specifications created by Sharp. 11 Panelview (503) 690-2460 www.whiteedc.com Panelview is a subsidiary of White Electronic Designs Corporation ENH104V2-380/450/600 Panelview Enhancing the Vision OPTICAL CHARACTERISTICS TA=25°C, VCC=3.3 / 5.0 V, INPUT SIGNALS: TYP. VALUES SHOWN IN SECTION 5 ITEM SYMBOL CONDITION MIN. TYP. MAX. UNIT Remarks CR q = f = 0° 150 300 1, 3 Lw q = f = 0° cd/m2 2, 3 Contrast Ratio Luminance ENH104V2-380 (IM only) ENH104V2-450 (IM, RP) ENH104V2-600 (IM, RP, ELG) Response Time 380 450 600 tr q = f = 0° 15 ms 3, 4 tf q = f = 0° 35 ms 3, 4 CR ³ 10 ° ° 3 3 Viewing Horizontal f -60~60 Angle Vertical q -45~55 Rx 0.54 0.57 0.60 Ry 0.30 0.33 0.36 Gx 0.30 0.33 0.36 0.49 0.52 0.55 Red Color Green Coordinates Gy q = f = 0° Blue Bx 0.14 0.17 0.20 By 0.15 0.18 0.21 White Wx 0.29 0.32 0.35 Wy 0.31 0.34 0.37 Notes: These items are measured using BM-5A(TOPCON) or LCD-7000(Otsuka Electronic) under the dark room condition (no ambient light). Condition: IL=6.0mArms, FL=55 kHz 1. Definition of Contrast Ratio CR=ON (White) Luminance / OFF(Black) Luminance: average of 5 points 2. Definition of Luminance Lw= ON (White) Luminance: average of 5 points (1,1) 120 160 320 1 2 5 240 360 480 3 4 (640,480) Measurement Point Original specifications created by Sharp. Panelview Hillsboro, OR (503) 690-2460 Panelview is a subsidiary of White Electronic Designs Corporation 12 3 ENH104V2-380/450/600 Panelview Enhancing the Vision 3. Definition of Viewing Angle ( q, f) Upper (+) φ θ Left (-) Right (+) LCD panel Lower (-) 4. Definition of Response Time Whi te 90% 90% L uminance 10% tr Black 10% tf Original specifications created by Sharp. 13 Panelview (503) 690-2460 www.whiteedc.com Panelview is a subsidiary of White Electronic Designs Corporation ENH104V2-380/450/600 Panelview Enhancing the Vision RELIABILITY TEST CONDITION TEMPERATURE AND HUMIDITY TEST ITEM CONDITIONS HIGH TEMPERATURE HIGH HUMIDITY OPERATION 40°C, 90%RH, 240 h HIGH TEMPERATURE STORAGE 60°C, 96 h LOW TEMPERATURE STORAGE -20°C, 96 h THERMAL SHOCK(NON-OPERATION) BETWEEN -20°C (1h) and 60°C(1h), 5 CYCLES SHOCK & VIBRATION ITEM CONDITIONS Shock level: 1470m/s2 (150G) SHOCK Waveform: half sinusoidal wave, 2ms (NON-OPERATION) Number of shocks: one shock input in each direction of three mutually perpendicular axis for a total of six shock inputs Vibration level: 9.8m/s2 (1.0G) Waveform: sinusoidal VIBRATION Frequency range: 5 to 500Hz (NON-OPERATION) Frequency sweep rate: 0.5 octave /min Duration: one sweep from 5 to 500 to 5Hz in each of three mutually perpendicular axis(total 3 hours) JUDGMENT STANDARD The judgment of the above tests should be made as follow: Pass: Normal display image with no obvious non-uniformity and no line defect. Partial transformation of the module parts should be ignored. Fail: No display image, obvious non-uniformity, or line defects. Original specifications created by Sharp. Panelview Hillsboro, OR (503) 690-2460 Panelview is a subsidiary of White Electronic Designs Corporation 14 ENH104V2-380/450/600 Panelview Enhancing the Vision HANDLING PRECAUTIONS FOR TFT-LCD MODULE ASSEMBLY PRECAUTION variation and color change. a. Use the mounting hole on the module when installing and do not bend or wrench the LCD during assembly. Do not drop, bend or twist LCD module while handling. g. Do not take the LCD module apart and reconstruct it, as this may affect the performance of the module. b. Design display housing in accordance with the following guide lines: i. Take care when handling the lead wire of the backlight so that it is not pulled on when connecting to the inverter. j. Connect the metal frame of LCD module to GND to minimize the effect of external noise and EMI. h. Avoid handling the metal frames with bare hands or soiled gloves. (a) Housing case must be designed carefully so as not to put stress on all 4 LCD sides and not to twist the module. (b) Keep sufficient clearance between the LCD module back surface and housing when the LCD module is mounted. Approximately 1.0mm of the clearance in the design is recommended taking into account the tolerance of the LCD module thickness and mounting structure height on the housing. OPERATING PRECAUTIONS a. Shut down the power supply before connecting and disconnecting signal input cable. b. Do not change variable resistance settings in LCD module. They are adjusted to the most suitable value. If changed, the LCD may not satisfy the characteristics specification. (c) When some parts, such as, FPC cable and ferrite plate, are installed underneath the LCD module, sufficient clearance is still required, such as 0.5mm. This clearance is especially to be considered when the additional parts are implemented for EMI countermeasure. c. d. Condensation might occur on the surface and inside of LCD module if there is a sudden change of ambient temperature. (d) Design the inverter location and connector position carefully so as not to cause stress to the lamp cable, or interface the LCD module by the lamp cable. e. Do not display the same pattern for a long period of time as image retention may occur. (e) Keep sufficient clearance between the LCD module and the others parts, such as the inverter so as not to interfere with the LCD module. Approximately 1.0mm of the clearance in the design is recommended. c. The LCD backlight takes longer to become stable of radiation characteristics in low temperatures than in room temperature. PRECAUTIONS WITH ELECTROSTATICS Do not push or scratch LCD panel surface with anything hard. Avoid touching the LCD surface with bare hands. (the Polarizer film surface of the LCD panel can be easily damaged.) a. Care should be exercised by making sure that one is grounded when handling. b. Remove the protective film slowly from the LCD module surface to prevent the occurrence of electrostatic. d. Do not allow contact between any parts with the rear side such as source TCP, gate TCP, control circuit board and FPCs when handling the LCD module. If contact with the rear side is unavoidable, handle the LCD module with care not to damage them. e. Use absorbent cotton or soft cloth for cleansing the LCD panel if soiled. f. Avoid liquid contact on the LCD panel surface, because damage could occur such as panel surface Original specifications created by Sharp. 15 Panelview (503) 690-2460 www.whiteedc.com Panelview is a subsidiary of White Electronic Designs Corporation ENH104V2-380/450/600 Panelview Enhancing the Vision STORAGE PRECAUTIONS a. Do not store LCDs in a high humidity and high temperature environment such as 60°C 90%RH. b. Do not store the LCDs in a low temperature environment below -20°C. SAFETY PRECAUTIONS a. When disposing of damaged or unnecessary LCDs, it is recommended to crush the LCDs rinse the pieces with solvents such as acetone and ethanol, which should later be burned. b. Wash hands off thoroughly with soap and water if they come in contact with the liquid from a leaking glass cell. c. Be sure to turn off the power supply when inserting or disconnecting the cable. d. Inverter should be designed carefully so as not to keep working in case of detecting over current or open circuit on the lamp. OTHERS a. A strong incident light into LCD panel might cause display characteristics changing inferior because of polarizer film, color filter, and other materials becoming inferior. Do not expose LCD module to direct sunlight and strong UV rays. b. Pay attention to a panel side of LCD module not to contact with other materials in preserving it alone. c. Use the following packing instructions; (a) The packing box and inner case for the LCD are designed to protect the LCDs from damage and scratching during transportation. Do not open the LCD boxes before use. (b) Do pile more than 5 boxes high, and do not store upside-down. (c) Keep the LCD boxes from being vibrated or thrown. (d) The packing box and inner case for the LCDs are made of cardboard, therefore avoid contact with water or high humidity. Original specifications created by Sharp. Panelview Hillsboro, OR (503) 690-2460 Panelview is a subsidiary of White Electronic Designs Corporation 16