ETC ENH150X1-200

ENH150X1-200/300
Panelview
Enhancing the Vision
ENH150X1-200/300 Color TFT-LCD Module Features
GENERAL DESCRIPTION
It is a wide viewing-angle-module (Vertical viewing angle:
120° Horizontal viewing angle: 140°).
Panelview provides optically enhanced solutions to the
standard Sharp LQ150X1DG16 color active matrix LCD
module. The first enhancement is an index matching
(IM) film lamination to the front surface of the display
polarizer. The IM film is available in two surface
treatments - IM/Clear and IM/110 (a 10% diffusion). The
second enhancement is the incorporation of a reflective
polarizer (RP) to improve brightness by up to 40%.
Input signal timing conforms with 75Hz mode of VESA
standard.
Panelview assumes no responsibility for any damage
resulting from the use of the device which does not
comply with the instructions and the precautions
specified in these specification sheets. Panelview does
assume the responsibility for the warranty of the
enhanced product.
The module is composed of a color TFT-LCD panel,
driver ICs, control circuit and power supply circuit and
a backlight unit. Graphics and text can be displayed on
a 1024x3x768 dot panel with 262,144 colors by
supplying 36 bit data signals (6bit x 2 pixel x RGB), four
timing signals, +5V DC supply voltage for TFT-LCD
panel driving and supply voltage for backlight.
MECHANICAL SPECIFICATIONS
Parameter
Display Size
Active Area
Pixel Format
Pixel Pitch
Pixel Configuration
Display Mode
Unit Outline Dimensions (1)
Mass
Surface Treatment
Specifications
38 (Diagonal)
15.0 (Diagonal)
304.1(H) x 228.1(V)
1024(H) x 768(V)
(1 pixel=R+G+B dots)
0.297(H) X 0.297(V)
RGB vertical stripe
Normally white
335(W)x257.9(H)x15.9(D)
1400 (max.)
IM/Clear (glossy) or IM/110 and
hardcoat 3H
Units
cm
inch
mm
pixel
–
mm
–
–
mm
g
–
Note:
1. Excludes backlight cables.
The thickness of module (D) does not contain the projection
2. Outline dimension shown in fig. 1
Original specifications created by Sharp.
August 2003 Rev. 0
ENH150X1-200/300
1
Panelview • (503) 690-2460 • www.whiteedc.com
Panelview is a subsidiary of White Electronic Designs Corporation
ENH150X1-200/300
Panelview
Enhancing the Vision
INPUT TEMINALS
TFT-LCD panel driving
CN1
The module-side connector
:FX8-60S-SV (Hirose Electric Co., Ltd.)
The user-side connector
:FX8-60P-SV (Hirose Electric Co., Ltd.)
Pin No.
Symbol
Function
1
GND
GND
2
RB0
RED even data signal (LSB)
3
RB1
RED even data signal
4
RB2
RED even data signal
5
RB3
RED even data signal
6
RB4
RED even data signal
7
RB5
RED even data signal (MSB)
8
GND
GND
9
GB0
GREEN even data signal (LSB)
10
GB1
GREEN even data signal
11
GB2
GREEN even data signal
12
GB3
GREEN even data signal
13
GB4
GREEN even data signal
14
GB5
GREEN even data signal (MSB)
15
GND
GND
16
BB0
BLUE even data signal (LSB)
17
BB1
BLUE even data signal
18
BB2
BLUE even data signal
19
BB3
BLUE even data signal
20
BB4
BLUE even data signal
21
BB5
BLUE even data signal (MSB)
22
GND
GND
23
RA0
RED odd data signal (LSB)
24
RA1
RED odd data signal
25
RA2
RED odd data signal
26
RA3
RED odd data signal
27
RA4
RED odd data signal
28
RA5
RED odd data signal (MSB)
29
GND
GND
30
GA0
GREEN odd data signal (LSB)
31
GA1
GREEN odd data signal
32
GA2
GREEN odd data signal
33
GA3
GREEN odd data signal
34
GA4
GREEN odd data signal
35
GA5
GREEN odd data signal (MSB)
36
GND
GND
37
BA0
BLUE odd data signal (LSB)
38
BA1
BLUE odd data signal
39
BA2
BLUE odd data signal
40
BA3
BLUE odd data signal
Original specifications created by Sharp.
Panelview • Hillsboro, OR • (503) 690-2460
Panelview is a subsidiary of White Electronic Designs Corporation
2
ENH150X1-200/300
Panelview
Enhancing the Vision
continued
Pin No.
Symbol
41
BA4
Function
BLUE odd data signal
42
BA5
BLUE odd data signal (MSB)
43
GND
GND
44
GND
GND
45
GND
GND
46
Vsync
Vertical synchronous signal
47
Hsync
Horizontal synchronous signal
48
ENAB
Data enable signal (Signal to settle the display position) (1)
49
GND
GND
50
GND
GND
51
CKB
Clock B signal for sampling even data signal
52
CKA
Clock A signal for sampling odd data signal
53
GND
GND
54
GND
GND (Reserve)
55
GND
56
MODE
57
Vcc
+5V power supply
58
Vcc
+5V power supply
59
Vcc
+5V power supply
60
Vcc
+5V power supply
GND (Reserve)
Timing signal select (1)
Shielding case is connected with GND in the module .
Note 1) In case MODE is fixed "Low", the display start timing is determined by Vsync and ENAB.
The vertical display start position and horizontal display start position are determined as described
on page 6. Do not keep ENAB "high" during operation.
In case MODE is fixed "High" or "Open", the display start timing is determined by only ENAB.
BACKLIGHT DRIVING
CN2,CN3
The module-side connector connector :BHR-03VS-1(JST)
The user-side connector
Pin no.
Symbol
1
VHIGH
2
NC
3
VLOW
:SM02(8.0)B-BHS-1(JST)
Function
Power supply for lamp
(High voltage side)
This is electronically opened
Power supply for lamp
(Low voltage side)
A BSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Condition
Rating
Unit
VI
Ta=25°C
–0.3 ~ +5.5
V
+5.0V Supply Voltage
VCC
Ta=25°C
0 ~ +6
V
Storage Temperature (2)
TSTG
–
–25 ~ +60
°C
Operation Temperature (Ambient) (2)
TOPA
–
0 ~ +50
°C
Input Voltage (1)
Note
1. CKA,CKB,RA0~RA5, GA0~GA5, BA0~BA5, RB0~RB5, GB0~GB5, BB0~BB5,Hsync, Vsync, ENAB,MODE
2. Humidity: 95%RH Max. (Ta ≤ 40°C). Maximum wet-bulb temperature at 39°C or less at (Ta>40°C). No
condensation.
Original specifications created by Sharp.
3
Panelview • (503) 690-2460 • www.whiteedc.com
Panelview is a subsidiary of White Electronic Designs Corporation
ENH150X1-200/300
Panelview
Enhancing the Vision
ELECTRICAL CHARACTERISTICS
TFT-LCD panel driving
Parameter
Ta=25°C
Symbol
Min.
Typ.
Max
Unit
Supply Voltage
VCC
+4.5
+5.0
+5.5
V
(1)
Current dissipation
I CC
–
300
450
mA
(2)
Permissive input ripple voltage
VRF
–
–
100
mVp-p
Vcc= +5.0V
Input voltage (Low)
VIL
GND
–
0.6
V
(3)
Input voltage (High)
VIH
2.6
–
Vcc
V
(3)
Input current (Low)
I IL
–
–
10
µA
VI =GND (3)
–
–
400
µA
VI =GND (4)
Input current (High)
I IH
–
–
10
µA
VI =VCC (3)
–
–
600
µA
VI =VCC (4)
Vcc
3.3(v) logic is recommended as input signals.
Notes:
1. On-off conditions for supply voltage
VCC
4.5V
Data
2.7V
0 < t1 ≤ 10ms
t4 ≥ 1s
VCC
Data
2.7V
t4
t1
VCC
2.7V
1) 2.7V ≤ VCC < 4.5V
td ≤ 10ms
2) VCC < 2.7V
VCC-dip conditions should also follow the
on-off conditions
4.5V
VCC-dip conditions
td
2. Typical current situation: 16-gray-bar pattern.
Vcc= +5.0V,
Gray scale : GS(4n)
n=0~15
The explanation of each gray scale, GS(4n), is described
on page 10.
RGB RGB RGB
RGB
RGB
GS0
GS56
GS60
GS4
GS8
3. CKA,CKB, RA0~RA5, GA0~GA5, BA0~BA5, RB0~RB5, GB0~GB5, BB0~BB5,
Hsync, Vsync, ENAB
4) MODE
Input circuit of MODE is
shown in right figure.
Vcc
Internal Power Supply (3.3V)
20kΩ
3.3kΩ
To control ASIC
MODE
10kΩ
Original specifications created by Sharp.
Panelview • Hillsboro, OR • (503) 690-2460
Panelview is a subsidiary of White Electronic Designs Corporation
4
Remark
ENH150X1-200/300
Panelview
Enhancing the Vision
BACKLIGHT DRIVING
The backlight system is an edge-lighting type with two CCFTs (Cold Cathode Fluorescent Tube).
The characteristics of the lamp are shown in the following table.
The value mentioned below is at the case of one CCFT.
Parameter
Symbol
Min.
Typ.
Max
Unit
Lamp current range
IL
2.5
6.0
6.5
mArms
Remark
(1)
Lamp voltage
VL
–
690
–
Vrms
Ta=25°C
(2)
Lamp power consumption
PL
–
4.1
–
W
Lamp frequency
FL
20
60
70
KHz
(3)
Kick-off voltage
VS
–
–
850
Vrms
Ta=25°C (4)
–
–
1450
Vrms
Ta=0°C (4)
Lamp life time
LL
50000
–
–
hour
(5)
Notes:
1. A lamp can be lit in the range of the lamp current shown above.
Maximum rating for current is measured by high frequency current measurement equipment connected
to VLOW at circuit shown below. (Note: To keep enough kick-off voltage and necessary steady
voltage for CCFT.)
Lamp frequency: 20~60kHz
1
Ambient temperature: 0~50°C
Module
3
A
Inverter
~
* 3pin is VLOW
2. Referential data per one CCFT by calculation (IL x VL).
The data does not include loss at inverter.
3. Lamp frequency of inverter may produce interference with horizontal synchronous frequency, and this
may cause horizontal beat on the display. Therefore, adjust lamp frequency and keep inverter far
from module or use electronic shielding between inverter and module to avoid interference.
4. The voltage above this value should be applied to the lamp for more than 1 second to startup. Otherwise,
the lamp may not turn on.
5. Lamp life time is defined as the time when either (1) or (2) occurs in the continuous operation under
the condition of Ta=25°C and IL = 6.0 ± 0.5mArms.
(1) Brightness becomes 50% of the original value under standard conditions.
(2) Kick-off voltage at Ta=0°C exceeds maximum value, 1450Vrms.
The performance of the backlight, for example life time or brightness, is influenced by the characteristics of the DC-AC inverter for the lamp.
When designing or ordering the inverter, make sure that poor lighting caused by the mismatch of the backlight and the inverter (miss-lighting,
flicker, etc.) do not occur. Once this is confirmed, the module should be operated in the same condition as it is installed in the instrument.
Original specifications created by Sharp.
5
Panelview • (503) 690-2460 • www.whiteedc.com
Panelview is a subsidiary of White Electronic Designs Corporation
ENH150X1-200/300
Panelview
Enhancing the Vision
TIMING CHARACTERISTICS OF INPUT SIGNALS
H-V mode (MODE = "Low")
Timing diagrams of input signal are shown in Fig. 2.
TIMING CHARACTERISTICS
Parameter
Min.
Typ.
Max.
Unit
Clock A
Frequency
1/Tc
25
32.5
40
MHz
Clock B
High time
TCH
9
–
–
ns
Low time
TCL
9
–
–
ns
Duty ratio
TCH/TCL
0.67
1.00
1.50
–
Setup time
TDS
8
–
–
ns
Hold time
TDH
8
–
–
ns
Cycle
TH
16.6
20.7
–
µs
528
672
860
clock
Pulse width
THP
2
68
–
clock
clock
Data
Horizontal
Symbol
sync. signal
Horizontal display start
TH BP
–
148
–
Hsync-Clock phase difference
TFC
5
–
–
ns
Vertical sync. signal
Cycle
TV
–
16.7
–
ms (1)
773
806
990
line
Pulse width
TVP
1
6
–
line
Vertical data start
TVBP
35
35
35
line
Hsync-Vsync phase difference
TVH
1
–
TH-THP
clock
Note 1): In case of lower frequency; the deterioration of display quality, flicker, etc. may occur.
HORIZONTAL DISPLAY POSITION
The horizontal display position is determined by ENAB signal and the input data corresponding to the rising edge
of ENAB signal is displayed at the left end of the active area.
Parameter
Enable signal
Symbol
Min.
Typ.
Max.
Setup time
TES
8
–
TC-10
ns
Pulse width
TEP
10
512
512
clock
TH E
THP + 1
148
TH-512
clock
Hsync-ENAB phase difference
Do not keep ENAB "Low" during operation.
Vertical Display Position
The vertical display start position is the 35th line from the falling edge of Vsync. (Fig. 2).
Original specifications created by Sharp.
Panelview • Hillsboro, OR • (503) 690-2460
Panelview is a subsidiary of White Electronic Designs Corporation
6
Unit
0.6V
7
TVh
0.6V
0.6V
0 line
0.6V
2.6V
DB3
DA3
2.6V
0.6V
2.6V
0.6V
Tep
Tds Tdh
35 line
DB512
DA512
0.6V
DH1
DH2
(Number of Horizontal sync)
34 line
DB511
DA511
Number of data
Fig 2 Input Signal Waveforms (H-V Mode)
TVbp
DB2
DA2
2.6V
Tes
DB1
DA1
2.6V
INVALID
1 line
TVp
THbp
0.6V
Tc
Tch Tcl
TH
DH3
TVd
INVALID
INVALID
TV
DH765
DH768
Number of data
INVALID
DB1
DA1
DB2
DA2
0.6V
DB3
DA3
Panelview
Data signal
(RA0~RA5, GA0~GA5,
BA0~BA5)
(RB0~RB5, GB0~GB5,
BB0~BB5)
Horizontal
sync. signal
(Hsync)
Vertical
sync. signal
(Vsync)
VENAB signal
THe
INVALID
Data B
(RB0~RB5, GB0~GB5,
BB0~BB5)
0.6V
0.6V
C1*
C0*
2.6V
INVALID
THc
Data A
(RA0~RA5, GA0~GA5,
BA0~BA5)
Clock signal A
Clock signal B
Horizontal
sync. signal
(Hsync)
THp
Enhancing the Vision
ENH150X1-200/300
Original specifications created by Sharp.
Panelview • (503) 690-2460 • www.whiteedc.com
Panelview is a subsidiary of White Electronic Designs Corporation
ENH150X1-200/300
Panelview
Enhancing the Vision
ENAB mode (MODE = "High" or "Open")
Timing diagrams of input signal are shown in Fig. 3.
TIMING CHARACTERISTICS
Parameter
Symbol
Min.
Typ.
Max.
Unit
Clock A
Frequency
1/TC
25
32.5
40
MHz
Clock B
High time
TCH
9
–
–
ns
Low time
TCL
9
–
–
ns
Duty ratio
TCH/TCL
0.67
1.00
1.50
–
–
ns
Data
Set-up time
TDS
8
–
Hold time
TDH
8
–
–
ns
Data enable
Set-up time
T ES
8
–
Tc-10
ns
signal
Horizontal period
TH
16.6
20.7
–
µs
528
672
860
clock
clock
Horizontal period (high)
THP
10
512
512
Vertical period
TV
770
806
990
line
Vertical blanking width
TVB
2
38
222
line
Note: If using an extended vertical period, the deterioration of display quality, flicker, etc. may occur.
Input Data Signals and Display Position on the Screen
Graphics and text can be displayed at 1024 x 3 x 768 dots on a panel with 262,144 colors by supplying 36 bit data
signal (6bit/color [64 gray scale] x 3 x 2 pixels).
RA GA BA RB GB BB
( 1, 1 )
Two pixel-data are sampled at the same time.
(1,1)
*DA : RA0~RA5, GA0~GA5, BA0~BA5
*DB : RB0~RB5, GB0~GB5, BB0~BB5
DA(1,1)
DB (1,1)
DA(1,2)
DB(1,2)
DA(2,1)
DB (512,1)
DA(1,3)
DB(512, 768)
DA(1,768)
Display position of Input data (H,Y)
Sleep Mode
This LCD module stops operation, and the picture of the LCD module becomes completely white, if ENAB signal
stays "Low” for over 0.5 sec. Follow the above input signal timing for normal operation.
Over 0.5s
0.6V
ENAB Signal
Original specifications created by Sharp.
Panelview • Hillsboro, OR • (503) 690-2460
Panelview is a subsidiary of White Electronic Designs Corporation
8
2.6 V
INVALID
9
DH1
2.6V
2.6V
0.6V
THp
0.6V
2.6V
0.6V
2.6V
TH
DB511
DA511
DH767
TV
DB512
DA512
DH768
0.6V
INVALID
TVb
Number of data
INVALID
INVALID
0.6V
Number of data
Fig 3 Input Signal Waveforms (ENAB Mode)
DH3
(1 line)
DB3
DA3
Tds Tdh
DH2
DB2
DA2
2.6V
Tes
DB1
DA1
0.6V
2.6V
DH1
2.6V
(2 line)
DH2
DH3
Panelview
Data signal
(RA0~RA5, GA0~GA5,
BA0~BA5)
(RB0~RB5, GB0~GB5,
BB0~BB5)
ENAB signal
INVALID
Data B
(RB0~RB5, GB0~GB5,
BB0~BB5)
ENAB signal
INVALID
DATA A
(RA0~RA5, GA0~GA5,
BA0~BA5)
Clock signal A
Clock signal B
Tc
Tch Tcl
Enhancing the Vision
ENH150X1-200/300
Original specifications created by Sharp.
Panelview • (503) 690-2460 • www.whiteedc.com
Panelview is a subsidiary of White Electronic Designs Corporation
ENH150X1-200/300
Panelview
Enhancing the Vision
INPUT SIGNALS, BASIC DISPLAY COLORS AND GRAY SCALE OF EACH COLOR
Colors &
Gray scale
Data Signal
Basic Colors
Gray
RA0 RA1 RA2 RA3 RA4 RA5 GA0 GA1 GA2 GA3 GA4 GA5 BA0 BA1 BA2 BA3 BA4 BA5
Scale
RB0 RB1 RB2 RB3 RB4 RB5 GB0 GB1 GB2 GB3 GB4 GB5 BB0 BB1 BB2 BB3 BB4 BB5
Black
-
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Blue
-
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
Green
-
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
Cyan
-
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
Red
-
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Magenta
-
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
Yellow
-
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
White
-
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Black
GS0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Gray Scale
of Red
↑
GS1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Darker
GS2
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
↑
↓
↓
↓
↓
↓
↓
↓
Brighter
GS61
1
0
1
1
1
1
0
0
0
↓
0
0
0
0
0
0
↓
0
0
0
↓
GS62
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Red
GS63
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Black
GS0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Gray Scale
of Green
↑
GS1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
Darker
GS2
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
↑
↓
↓
↓
↓
↓
↓
↓
Brighter
GS61
0
0
0
0
0
0
1
0
1
↓
1
1
1
0
0
0
↓
0
0
0
↓
GS62
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
Green
GS63
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
Black
GS0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Gray Scale
of Blue
↑
GS1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
Darker
GS2
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
↑
↓
↓
↓
↓
↓
↓
↓
Brighter
GS61
0
0
0
0
0
0
0
0
0
↓
0
0
0
1
0
1
↓
1
1
1
↓
GS62
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
Blue
GS63
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0: Low level voltage 1: High level voltage
Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit data signals, the
262,144-color display can be achieved on the screen.
Original specifications created by Sharp.
Panelview • Hillsboro, OR • (503) 690-2460
Panelview is a subsidiary of White Electronic Designs Corporation
10
ENH150X1-200/300
Panelview
Enhancing the Vision
OPTICAL CHARACTERISTICS
TA=25°C, VCC=+5V
Symbol
Condition
Min.
Typ.
Max.
Unit
Remark
Viewing
Parameter
Horizontal
θ 21,θ 22
CR>5
60
70
–
Deg.
(1,4)
angle
Vertical
θ 11
45
60
–
Deg.
Deg.
θ 12
range
Contrast ratio
CRn
Response
time
Rise
tr
Decay
θ = 0°
50
60
–
200
300
–
–
(2,4)
–
10
25
ms
(3,4)
td
–
35
50
ms
Chromaticity of
x
0.283
0.313
0.343
–
white
y
0.299
0.329
0.359
–
Chromaticity of
x
0.548
0.578
0.608
–
red
y
0.302
0.332
0.362
–
Chromaticity of
x
0.280
0.310
0.340
–
green
y
0.520
0.550
0.580
–
Chromaticity of
x
0.123
0.153
0.183
–
blue
y
0.100
0.130
0.160
–
Luminance of white
IM film
IM, RP
YLI
150
200
200
300
–
–
cd/m2
I L=6.0mArms
(4)
White Uniformity
δw
–
–
1.35
–
(5)
(4)
(4)
(4)
(4)
The measurement shall be executed 30 minutes after lighting at rating. (typical condition: IL=6mArms)
The optical characteristics shall be measured in a dark room or equivalent state with the method shown in Fig.4 below.
Photodetector
(BM-5A: TOPCON)
Field=2°
400mm
TFT-LCD Module
LCD Panel
Center of the screen
Original specifications created by Sharp.
11
Panelview • (503) 690-2460 • www.whiteedc.com
Panelview is a subsidiary of White Electronic Designs Corporation
ENH150X1-200/300
Panelview
Enhancing the Vision
Normal line
Notes:
θ22
1) Definitions of viewing angle range:
θ11
θ12
θ21
6 o'clock direction
2) Definition of contrast ratio:
Contrast Ratio (CR) =
Luminance (brightness) with all pixels white
Luminance (brightness) with all pixels black
black
white
Photodetector output
(Relative Value)
3) Definition of response time:
The response time is defined as the following figure and shall be
measured by switching the input signal for “black” and “white”.
white
100%
90%
10%
0%
td
tr
time
4) This shall be measured at the center of the screen.
5) Definition of white uniformity:
White uniformity is defined as the
following with five measurements
(A~E).
256
512
768 pixel
D
A
384
C
B
δw =
Maximum Luminance of five points (brightness)
Minimum Luminance of five points (brightness)
Original specifications created by Sharp.
Panelview • Hillsboro, OR • (503) 690-2460
Panelview is a subsidiary of White Electronic Designs Corporation
12
192
E
576
pixel
ENH150X1-200/300
Panelview
Enhancing the Vision
HANDLING PRECAUTIONS
a) Be sure to turn off the power supply when inserting
or disconnecting the cable.
b) Be sure to design the cabinet so that the module
can be installed without any extra stress such as
warp or twist.
c) Since the front polarizer is easily damaged, pay
attention not to scratch it.
d) Since prolonged contact with water may cause
discoloration or spots, wipe off water drops
immediately.
e) When the panel surface is soiled, wipe it with
absorbent cotton or other soft cloth.
f)
Since the panel is made of glass, it may break
or crack if dropped or bumped on hard surface.
Handle with care.
g) Since CMOS LSI is used in this module, take
care of static electricity and make sure that one is
grounded when handling.
h) This module has its circuitry PCBs on the rear
side and should be carefully handled in order
not to be stressed.
i)
When desinging the cabinet, take into consideration
the access to the backlight assembly.
j)
When some pressure is added onto the module
from rear side constantly, it causes display nonuniformity issues, functional defect, etc. Such a
design should be avoided.
PACKING FORM
a) Piling number of cartons
: 5 cartons
b) Packing quantity in one carton
: 5 modules
c) Carton size
: 410mm(W) X 500mm(D) X 225mm(H)
d) Total weight of one carton filled with full modules
: 8850g
Original specifications created by Sharp.
13
Panelview • (503) 690-2460 • www.whiteedc.com
Panelview is a subsidiary of White Electronic Designs Corporation
ENH150X1-200/300
Panelview
Enhancing the Vision
RELIABLITY TEST ITEMS
No.
Test item
Conditions
1
High temperature storage test
Ta=60°C
2
Low temperature storage test
Ta=25°C
3
High temperature
240h
Ta=40°C ;
& high humidity operation test
4
240h
95%RH
240h
(No condensation)
High temperature operation test
Ta=50°C
240h
(The panel temp. must be less than 60°C)
5
Low temperature operation test
6
Vibration test
Ta=0°C
240h
Frequency : 10~57Hz/Vibration width (one side): 0.075mm
(non operating)
: 58~500Hz/Gravity: 9.8m/s2
Sweep time : 11 minutes
Test period : 3 hours
(1 hour for each direction of X,Y,Z)
7
Shock test
Max. gravity: 490m/s2
(non operating)
Pulse width : 11 ms, sine wave
Direction: ±X, ±Y, ±Z
once for each direction.
(Result Evaluation Criteria)
Under the display quality test conditions with normal operation state, there shall be no change
which may affect practical display function.
OTHERS
1) Disassembling the module can cause permanent
damage and should be strictly avoided.
2) Image retention may occur when a fixed pattern is
displayed for a long period of time.
Original specifications created by Sharp.
Panelview • Hillsboro, OR • (503) 690-2460
Panelview is a subsidiary of White Electronic Designs Corporation
14
ENH150X1-200/300
Panelview
Enhancing the Vision
8.5
COVER
CCFT CONNECTOR
7
7
8.5
13.2
Fig. 1 Outline Dimensions
5.9
CN2 : BHR-03VS-1 (JST)
PIN LAYOUT
347
4
HC
GND
4
172.5
90
165.8
(162.5)
165.5
7
4.3
M 2.5 SCREW
(4 POINTS)
High
1
2
3
+10
-10
CN2
3
1
M 2.5 SCREW
(4 POINTS)
ACTIVE AREA
4.4
308.2 x 232.1
127.9
88
32
210
47
13
4.4
2 - ∅4.4
4- R 0.5
CN2
6.6
1
4.3
3
172.5
7
14.6
TAPE
8.5
331.3
347
7
14.5
7
8.5
13.2
112.5
210
257.9
32
47
88
105
105
6.6
130
112.5
BEZEL OPENING
13
304.1 x 228.1
Rear View
Notes:
1) Unspecified tolerance to be ±0.5
2) Warp and floating for PCB and chassis are excluded from thickness
and dimensions of the unit.
CN1
1
Original specifications created by Sharp.
15
Panelview • (503) 690-2460 • www.whiteedc.com
Panelview is a subsidiary of White Electronic Designs Corporation