ETC P15460EJ1V0IF00

Information
TAPING SPECIFICATIONS AND PACKING
OUTLINE DRAWING OF 16/20-PIN PLASTIC
SSOP (5.72 mm (225)) FOR MICROWAVE
SEMICONDUCTORS
Document No. P15460EJ1V0IF00 (1st edition)
Date Published July 2001 N CP(K)
©
Printed in Japan
2001
[MEMO]
2
Information P15460EJ1V0IF
• The information in this document is current as of July, 2001. The information is subject to change
without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data
books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products
and/or types are available in every country. Please check with an NEC sales representative for
availability and additional information.
• No part of this document may be copied or reproduced in any form or by any means without prior
written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document.
• NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of
third parties by or arising from the use of NEC semiconductor products listed in this document or any other
liability arising from the use of such products. No license, express, implied or otherwise, is granted under any
patents, copyrights or other intellectual property rights of NEC or others.
• Descriptions of circuits, software and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these
circuits, software and information in the design of customer's equipment shall be done under the full
responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third
parties arising from the use of these circuits, software and information.
• While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers
agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize
risks of damage to property or injury (including death) to persons arising from defects in NEC
semiconductor products, customers must incorporate sufficient safety measures in their design, such as
redundancy, fire-containment, and anti-failure features.
• NEC semiconductor products are classified into the following three quality grades:
"Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products
developed based on a customer-designated "quality assurance program" for a specific application. The
recommended applications of a semiconductor product depend on its quality grade, as indicated below.
Customers must check the quality grade of each semiconductor product before using it in a particular
application.
"Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment
and industrial robots
"Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support)
"Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems and medical equipment for life support, etc.
The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's
data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not
intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness
to support a given application.
(Note)
(1) "NEC" as used in this statement means NEC Corporation and also includes its majority-owned subsidiaries.
(2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for
NEC (as defined above).
M8E 00. 4
Information P15460EJ1V0IF
3
CONTENTS
1. DESCRIPTION .........................................................................................................................................5
2. INDICATION OF PART NUMBER ........................................................................................................5
2.1 Indication of part number ..............................................................................................................................5
2.2 Device orientation in the carrier tape ...........................................................................................................5
2.3 An example of indication ...............................................................................................................................5
3. TAPE AND REEL SPECIFICATIONS ..................................................................................................6
3.1 Tape dimensions ............................................................................................................................................6
3.2 Reel dimensions.............................................................................................................................................8
3.3 Leader and trailer of carrier tape ..................................................................................................................9
3.4 Sealing strength between tapes..................................................................................................................10
4. PACKING ...............................................................................................................................................11
4.1 Quantity of packing ......................................................................................................................................11
4.2 Indication of part number and quantity to the reel....................................................................................11
4.3 Indication of part number and quantity to the packing case ...................................................................11
5. PACKING OUTLINE DRAWING..........................................................................................................12
5.1 Tape and reel ................................................................................................................................................12
5.2 Packing box specifications .........................................................................................................................12
4
Information P15460EJ1V0IF
1.
DESCRIPTION
This information sheet is intended to cover standards on tape and reel of the 16/20-pin plastic SSOP (5.72 mm
(225)) for high frequency semiconductors on NEC Corporation.
2.
INDICATION OF PART NUMBER
The part number of tape and reel packing device is following.
2.1
Indication of part number
Part number of device
Symbol of device orientation (cf. 2.2)
Indicating the embossed carrier tape
2.2
Device orientation in the carrier tape
“-E1” Orientation
Pin 1 of the device faces toward the open end of the tape, away from the reel
“-E2” Orientation
Pin 1 of the device faces away from the open end of the tape, toward the reel
Remark
Depending the part number, we can not provide both “-E1” and “-E2” type device.
Please check the availability of each part number of the device.
-E1
-E2
Tape drawout direction
Tape drawout direction
Pin 1 indication
2.3
An example of indication
µPC2798GR-E1 : The tape and reel packing µPC2798GR, in which pin 1 of the device faces toward open end of
the tape.
Information P15460EJ1V0IF
5
3.
TAPE AND REEL SPECIFICATIONS
3.1
Tape dimensions
16-pin SSOP (5.72 mm (225))
This carrier tape is applied treatment of electro static prevention.
P1
φ D0
P0
E
T
W
B0
F
P2
A0
T2
φ D1
Tape drawout direction
(Unit: mm)
Symbol
A0
B0
φD0
φD1
E
F
P0
P1
P2
T
T2
W
Specification
6.8
±0.1
5.75
±0.1
φ1.5
+0.1
−0
φ1.5
MIN.
1.75
±0.1
5.5
±0.05
4.0
±0.1
8.0
±0.1
2.0
±0.05
0.3
±0.05
2.1
±0.1
12.0
±0.3
The dimensions of the A0 and B0 are indicated inside of the bottom of the pocket.
6
Information P15460EJ1V0IF
20-pin SSOP (5.72 mm (225))
This carrier tape is applied treatment of electro static prevention.
P1
φ D0
P0
E
T
W
B0
F
P2
A0
T2
φ D1
Tape drawout direction
(Unit: mm)
Symbol
A0
B0
φD0
φD1
E
F
P0
P1
P2
T
T2
W
Specification
6.8
±0.1
7.2
±0.1
φ1.5
+0.1
−0
φ1.5
MIN.
1.75
±0.1
5.5
±0.05
4.0
±0.1
8.0
±0.1
2.0
±0.05
0.3
±0.05
2.1
±0.1
12.0
±0.3
The dimensions of the A0 and B0 are indicated inside of the bottom of the pocket.
Information P15460EJ1V0IF
7
3.2
Reel dimensions
16/20-pin SSOP (5.72 mm (225)) Common
A
C
B
This reel is applied treatment of electro static prevention
F
E
θ1
W1
W2
D
Magnification figure of F part
(Unless otherwise specified, Unit: mm)
8
Symbol
A
B
C
D
E
W1
W2
θ1
Specification
φ 330 ±2
φ 100
±1
φ 13.0
±0.2
φ 21.0
±0.8
2.0
±0.5
13.5
±1
17.5
±1
120°
Information P15460EJ1V0IF
3.3
Leader and trailer of carrier tape
Adhesive tape
Empty carrier tape
Trailer
Cover
tape only
Leader
Label
(Unit: mm)
Item
Leader
Cover tape
Empty carrier tape
Trailer
Empty carrier tape
Specification
−
Remarks
Tip taped to roll, and fixed by adhesive tape
100 MIN.
The winding direction is shown above
400 MIN.
Length of cover tape + empty carrier tape
160 MIN.
Information P15460EJ1V0IF
9
3.4
Sealing strength between tapes
Item
Data
Cover tape adhesion
0.1 to 1.3 N
Remarks
Peeling angle: 165° to 180° ,
Peeling speed: 300 ± 10 mm/min.
Cover tape
165° to 180°
F
Carrier tape
Direction of tape
10
Information P15460EJ1V0IF
4.
PACKING
4.1
Quantity of packing
2 500 pieces/reel
4.2
Indication of part number and quantity to the reel
Part number, quantity, class and lot number are indicated at the side of the reel.
4.3
Indication of part number and quantity to the packing case
Part number, quantity, class and lot number are indicated at the side of packing case.
Information P15460EJ1V0IF
11
5.
5.1
PACKING OUTLINE DRAWING
Tape and reel
-E1 type
-E2 type
Label
Direction of feed
5.2
Packing box specifications
L
H
Label
W
Contents of Label Indication
Tape and Reel
Applied Package
16-pin Plastic SSOP (5.72 mm (225))
Packing Box
Quantity
(pcs)
Dimension (mm)
(W × H × L)
Quantity
(reels)
2 500
343 × 53 × 343
2
20-pin Plastic SSOP (5.72 mm (225))
12
Part Number, Quantity, Lot Number, Class
Information P15460EJ1V0IF
[MEMO]
Information P15460EJ1V0IF
13
[MEMO]
14
Information P15460EJ1V0IF
Facsimile Message
From:
Name
Company
Tel.
Although NEC has taken all possible steps
to ensure that the documentation supplied
to our customers is complete, bug free
and up-to-date, we readily accept that
errors may occur. Despite all the care and
precautions we've taken, you may
encounter problems in the documentation.
Please complete this form whenever
you'd like to report errors or suggest
improvements to us.
FAX
Address
Thank you for your kind support.
North America
Hong Kong, Philippines, Oceania
NEC Electronics Inc.
NEC Electronics Hong Kong Ltd.
Corporate Communications Dept. Fax: +852-2886-9022/9044
Fax: +1-800-729-9288
+1-408-588-6130
Korea
Europe
NEC Electronics Hong Kong Ltd.
NEC Electronics (Europe) GmbH
Seoul Branch
Technical Documentation Dept.
Fax: +82-2-528-4411
Fax: +49-211-6503-274
South America
NEC do Brasil S.A.
Fax: +55-11-6462-6829
Asian Nations except Philippines
NEC Electronics Singapore Pte. Ltd.
Fax: +65-250-3583
Japan
NEC Semiconductor Technical Hotline
Fax: +81- 44-435-9608
Taiwan
NEC Electronics Taiwan Ltd.
Fax: +886-2-2719-5951
I would like to report the following error/make the following suggestion:
Document title:
Document number:
Page number:
If possible, please fax the referenced page or drawing.
Document Rating
Excellent
Good
Acceptable
Poor
Clarity
Technical Accuracy
Organization
CS 01.2