Features • EE Programmable 65,536 x 1-, 131,072 x 1-, and 262,144 x 1-bit Serial Memories • • • • • • • • • • Designed to Store Configuration Programs for Field Programmable Gate Arrays (FPGAs) In-System Programmable (ISP) via 2-wire Bus Simple Interface to SRAM FPGAs Compatible with Atmel AT6000, AT40K and AT94K Devices, Altera FLEX®, APEX™ Devices, Lucent ORCA® FPGAs, Xilinx XC3000™, XC4000™, XC5200™, Spartan®, Virtex™ FPGAs, Motorola MPA1000 FPGAs Cascadable Read-back to Support Additional Configurations or Higher-density Arrays Low-power CMOS EEPROM Process Programmable Reset Polarity Available in 6 mm x 6 mm x 1 mm 8-lead LAP (Pin-compatible with 8-lead SOIC/VOIC Packages), 8-lead PDIP, 8-lead SOIC and 20-lead PLCC Packages (Pin Compatible Across Product Family) Emulation of Atmel’s AT24CXXX Serial EEPROMs Available in 3.3V ± 10% LV and 5V ± 5% C Versions Low-power Standby Mode Description The AT17C65/128/256 and AT17LV65/128/256 (low-density AT17 Series) FPGA configuration EEPROMs (Configurators) provide an easy-to-use, cost-effective configuration memory for Field Programmable Gate Arrays. The low-density AT17 Series is packaged in the 8-lead LAP, the 8-lead PDIP, the 8-lead SOIC and the popular 20-lead PLCC. The AT17 Series uses a simple serial-access procedure to configure one or more FPGA devices. The user can select the polarity of the reset function by programming four EEPROM bytes. These devices also support a write-protection mechanism within its programming mode. The AT17 Series Configurators can be programmed with industry-standard programmers, Atmel’s ATDH2200E Programming Kit or Atmel’s ATDH2225 ISP Cable. FPGA Configuration EEPROM Memory 64-kilobit, 128-kilobit and 256-kilobit AT17C65 AT17LV65 AT17C128 AT17LV128 AT17C256 AT17LC256 Rev. 1636E–12/01 1 Pin Configurations 8-lead LAP 8 7 6 5 VCC SER_EN CEO (A2) GND DATA CLK (WP) RESET/OE CE 1 2 3 4 VCC SER_EN CEO (A2) GND 20-lead PLCC 8 7 6 5 VCC SER_EN CEO (A2) GND CLK NC (WP) RESET/OE NC CE 4 5 6 7 8 18 17 16 15 14 NC SER_EN NC NC CEO (A2) NC GND NC NC NC DATA CLK (WP) RESET/OE CE 8 7 6 5 NC DATA NC VCC NC 8-lead SOIC 1 2 3 4 3 2 1 20 19 1 2 3 4 9 10 11 12 13 DATA CLK RESET/OE CE 8-lead PDIP 2 AT17C/LV65/128/256 1636E–12/01 AT17C/LV65/128/256 Block Diagram POWER ON RESET Device Description The control signals for the configuration EEPROM (CE, RESET/OE and CCLK) interface directly with the FPGA device control signals. All FPGA devices can control the entire configuration process and retrieve data from the configuration EEPROM without requiring an external intelligent controller. The configuration EEPROM RESET/OE and CE pins control the tri-state buffer on the DATA output pin and enable the address counter. When RESET/OE is driven High, the configuration EEPROM resets its address counter and tri-states its DATA pin. The CE pin also controls the output of the AT17 Series Configurator. If CE is held High after the RESET/OE reset pulse, the counter is disabled and the DATA output pin is tri-stated. When OE is subsequently driven Low, the counter and the DATA output pin are enabled. When RESET/OE is driven High again, the address counter is reset and the DATA output pin is tri-stated, regardless of the state of CE. When the configurator has driven out all of its data and CEO is driven Low, the device tri-states the DATA pin to avoid contention with other configurators. Upon power-up, the address counter is automatically reset. This is the default setting for the device. Since almost all FPGAs use RESET Low and OE High, this document will describe RESET/OE. 3 1636E–12/01 -+ Pin Description 8 DIP/ LAP/ SOIC Pin 20 PLCC Pin Name I/O Description 1 2 DATA I/O Three-state DATA output for configuration. Open-collector bi-directional pin for programming. 2 4 CLK I Clock input. Used to increment the internal address and bit counter for reading and programming. 3 6 RESET/OE I Output Enable (active High) and RESET (active Low) when SER_EN is High. A Low level on RESET/OE resets both the address and bit counters. A High level (with CE Low) enables the data output driver. The logic polarity of this input is programmable as either RESET/OE or RESET/OE. For most applications, RESET should be programmed active Low. This document describes the pin as RESET/OE. WP(1) I Write protect (WP) input (when CE is Low) during programming only (SER_EN Low). When WP is Low, the entire memory can be written. When WP is enabled (High), the lowest block of the memory cannot be written. I Chip Enable input (active Low). A Low level (with OE High) allows DCLK to increment the address counter and enables the data output driver. A High level on CE disables both the address and bit counters and forces the device into a low-power standby mode. Note that this pin will not enable/disable the device in the 2-wire Serial Programming mode ( SER_EN Low). 4 8 CE 5 10 GND 6 14 CEO O Chip Enable Output (active Low). This output goes Low when the address counter has reached its maximum value. In a daisy chain of AT17 Series devices, the CEO pin of one device must be connected to the CE input of the next device in the chain. It will stay Low as long as CE is Low and OE is High. It will then follow CE until OE goes Low; thereafter, CEO will stay High until the entire EEPROM is read again. A2 I Device selection input, A2. This is used to enable (or select) the device during programming (i.e., when SER_EN is Low). A2 has an internal pull-down resistor. I Serial enable must be held High during FPGA loading operations. Bringing SER_EN Low enables the 2-wire Serial Programming Mode. For non-ISP applications, SER_EN should be tied to VCC. 7 17 SER_EN 8 20 VCC Note: 4 Ground pin. A 0.2 µF decoupling capacitor between VCC and GND is recommended. +3.3V/+5V power supply pin. 1. This pin is not available for the LAP package. AT17C/LV65/128/256 1636E–12/01 AT17C/LV65/128/256 FPGA Master Serial Mode Summary The I/O and logic functions of any SRAM-based FPGA are established by a configuration program. The program is loaded either automatically upon power-up, or on command, depending on the state of the FPGA mode pins. In Master mode, the FPGA automatically loads the configuration program from an external memory. The AT17 Serial Configuration EEPROM has been designed for compatibility with the Master Serial mode. This document discusses the Atmel AT40K, AT40KAL and AT94KAL applications as well as Xilinx applications. Control of Configuration Cascading Serial Configuration EEPROMs Most connections between the FPGA device and the AT17 Serial EEPROM are simple and self-explanatory. • The DATA output of the AT17 Series Configurator drives DIN of the FPGA devices. • The master FPGA CCLK output drives the CLK input of the AT17 Series Configurator. • The CEO output of any AT17 Series Configurator drives the CE input of the next Configurator in a cascade chain of EEPROMs. • SER_EN must be connected to VCC (except during ISP). For multiple FPGAs configured as a daisy-chain, or for FPGAs requiring larger configuration memories, cascaded configurators provide additional memory. After the last bit from the first configurator is read, the clock signal to the configurator asserts its CEO output low and disables its DATA line driver. The second configurator recognizes the low level on its CE input and enables its DATA output. After configuration is complete, the address counters of all cascaded configurators are reset if the RESET/OE on each configurator is driven to its active (Low) level. If the address counters are not to be reset upon completion, then the RESET/OE input can be tied to its inactive (High) level. AT17 Series Reset Polarity The AT17 Series Configurator allows the user to program the reset polarity as either RESET/OE or RESET/OE. This feature is supported by industry-standard programmer algorithms. Programming Mode The programming mode is entered by bringing SER_EN Low. In this mode the chip can be programmed by the 2-wire serial bus. The programming is done at VCC supply only. Programming super voltages are generated inside the chip. The AT17C parts are read/write at 5V nominal. The AT17LV parts are read/write at 3.3V nominal. Standby Mode The AT17C/LV65/128/256 enters a low-power standby mode whenever CE is asserted High. In this mode, the configurator consumes less than 75 µA of current at 5.0V. The output remains in a high-impedance state regardless of the state of the OE input. 5 1636E–12/01 Example Circuits Figure 1. AT17 Series Device for Programming PSLI Devices AT17 Series Device AT40K/AT40KAL/AT94K RESET RESET M2 M1 M0 VCC SER_EN DATA CLK CE (2) RESET/OE(1) READY DATA0 CCLK CON INIT GND Notes: 1. Reset polarity must be set to active Low. 2. Use of the optional READY pin is not available on the AT17C/LV65/128/256 devices. The FPGA CON/DONE output drives the CE input of the AT17 Series Configurator, while the RESET/OE input is driven by the FPGA INIT pin. This connection works under all normal circumstances, even when the user aborts the configuration before CON/DONE has gone High. A Low level on the RESET/OE input, during FPGA reset, clears the configurator’s internal address pointer so that the reconfiguration starts at the beginning. Figure 2. Drop-In Replacement of XC17/ATT17 PROMs for Xilinx/Lucent FPGA Applications VCC 4.7 kW XILINX FPGA PROGRAM PROGRAM M2 M1 M0 DIN CCLK DONE(3) INIT AT17 Series Device VCC SER_EN DATA CLK CE (2) RESET/OE(1) READY GND Notes: 6 1. Reset polarity must be set to active Low. 2. Use of the optional READY pin is not available on the AT17C/LV65/128/256 devices. 3. An internal pull-up resistor is enabled here for DONE. AT17C/LV65/128/256 1636E–12/01 AT17C/LV65/128/256 For details of ISP, please refer to the “Programming Specification for Atmel's AT17 and AT17A Series FPGA Configuration EEPROMs”, available on the Atmel web site, at http://www.atmel.com/atmel/acrobat/doc0437.pdf. Figure 3. In-System Programming of AT17 Series for PSLI Applications VCC VCC 4.7 kW 4.7 kW DATA 1 SCLK 3 2 5 6 7 8 9 10 4 VCC GND AT17 Series Device AT40K/AT40KAL/AT94K RESET RESET M2 M1 M0 DATA0 CCLK CON INIT SER_EN SER_EN DATA CLK CE (2) RESET/OE(1) READY GND Notes: 1. Reset polarity must be set to active Low. 2. Use of the optional READY pin is not available on the AT17C/LV65/128/256 devices. Figure 4. In-System Programming of AT17 Series for Xilinx/Lucent FPGA Applications VCC VCC 4.7 kW DATA 1 SCLK 3 2 5 6 7 8 9 10 VCC VCC 4.7 kW 4 VCC 4.7 kW XILINX FPGA PROGRAM PROGRAM 4.7 kW M2 M1 M0 DIN CCLK DONE(3) INIT AT17 Series Device GND SER_EN SER_EN DATA CLK CE (1) READY(2) RESET/OE GND Notes: 1. Reset polarity must be set to active Low. 2. Use of the optional READY pin is not available on the AT17C/LV65/128/256 devices. 3. An internal pull-up resistor is enabled here for DONE. 7 1636E–12/01 Absolute Maximum Ratings* Operating Temperature.................................. -55°C to +125°C *NOTICE: Storage Temperature ..................................... -65 °C to +150°C Voltage on Any Pin with Respect to Ground ..............................-0.1V to VCC +0.5V Supply Voltage (VCC) .........................................-0.5V to +7.0V Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those listed under operating conditions is not implied. Exposure to Absolute Maximum Rating conditions for extended periods of time may affect device reliability. Maximum Soldering Temp. (10 sec. @ 1/16 in.).............260°C ESD (RZAP = 1.5K, CZAP = 100 pF)................................. 2000V Operating Conditions AT17CXXX Symbol VCC 8 Description AT17LVXXX Min Max Min Max Units Commercial Supply voltage relative to GND -0°C to +70°C 4.75 5.25 3.0 3.6 V Industrial Supply voltage relative to GND -40°C to +85°C 4.5 5.5 3.0 3.6 V Military Supply voltage relative to GND -55°C to +125°C 4.5 5.5 3.0 3.6 V AT17C/LV65/128/256 1636E–12/01 AT17C/LV65/128/256 DC Characteristics VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial/Military Symbol Description Min Max Units VIH High-level Input Voltage 2.0 VCC V VIL Low-level Input Voltage 0 0.8 V VOH High-level Output Voltage (IOH = -4 mA) VOL Low-level Output Voltage (IOL = +4 mA) VOH High-level Output Voltage (IOH = -4 mA) VOL Low-level Output Voltage (IOL = +4 mA) VOH High-level Output Voltage (IOH = -4 mA) VOL Low-level Output Voltage (IOL = +4 mA) 0.4 V ICCA Supply Current, Active Mode 10 mA IL Input or Output Leakage Current (VIN = VCC or GND) 10 µA Commercial 75 µA ICCS Supply Current, Standby Mode Industrial/Military 150 µA 3.7 V Commercial 0.32 3.6 V V Industrial 0.37 3.5 V V Military -10 DC Characteristics VCC = 3.3V ± 10% Symbol Description Min Max Units VIH High-level Input Voltage 2.0 VCC V VIL Low-level Input Voltage 0 0.8 V VOH High-level Output Voltage (IOH = -2.5 mA) VOL Low-level Output Voltage (IOL = +3 mA) VOH High-level Output Voltage (IOH = -2 mA) VOL Low-level Output Voltage (IOL = +3 mA) VOH High-level Output Voltage (IOH = -2 mA) VOL Low-level Output Voltage (IOL = +2.5 mA) ICCA Supply Current, Active Mode IL Input or Output Leakage Current (VIN = VCC or GND) ICCS Supply Current, Standby Mode 2.4 V Commercial 0.4 2.4 V V Industrial 0.4 2.4 V V Military 0.4 V 5 mA 10 µA Commercial 50 µA Industrial/Military 100 µA -10 9 1636E–12/01 AC Characteristics CE TSCE TSCE THCE RESET/OE TLC THOE THC CLK TOE TOH TCAC TDF TCE DATA TOH AC Characteristics when Cascading RESET/OE CE CLK TCDF DATA FIRST BIT LAST BIT TOCK TOCE TOOE CEO TOCE 10 AT17C/LV65/128/256 1636E–12/01 AT17C/LV65/128/256 AC Characteristics for AT17C65/128/256 VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial/Military Commercial Symbol Description TOE(2) OE to Data Delay (2) TCE TCAC (2) Min Max Industrial/Military(1) Max Units 30 35 ns CE to Data Delay 45 45 ns CLK to Data Delay 50 55 ns TOH Data Hold from CE, OE, or CLK TDF(3) CE or OE to Data Float Delay TLC CLK Low Time 20 20 ns THC CLK High Time 20 20 ns TSCE CE Setup Time to CLK (to guarantee proper counting) 35 40 ns THCE CE Hold Time from CLK (to guarantee proper counting) 0 0 ns THOE OE High Time (guarantees counter is reset) 20 20 ns FMAX Maximum Input Clock Frequency 12.5 12.5 MHz Notes: 0 Min 0 50 ns 50 ns 1. Preliminary specifications for military operating range only. 2. AC test load = 50 pF. 3. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. AC Characteristics for AT17C65/128/256 when Cascading VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial/Military Commercial Symbol (3) Description Min Max Industrial/Military(1) Min Max Units CLK to Data Float Delay 50 50 ns TOCK(2) CLK to CEO Delay 35 40 ns TOCE(2) CE to CEO Delay 35 35 ns TOOE(2) RESET/OE to CEO Delay 30 35 ns FMAX Maximum Input Clock Frequency TCDF Notes: 10 10 MHz 1. Preliminary specifications for military operating range only. 2. AC test load = 50 pF. 3. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. 11 1636E–12/01 AC Characteristics for AT17LV65/128/256 VCC = 3.3V ± 10% Commercial Symbol Description TOE(2) OE to Data Delay (2) TCE TCAC (2) Min Max Industrial/Military(1) Max Units 50 55 ns CE to Data Delay 60 60 ns CLK to Data Delay 75 80 ns TOH Data Hold from CE, OE, or CLK TDF(3) CE or OE to Data Float Delay TLC CLK Low Time 25 25 ns THC CLK High Time 25 25 ns TSCE CE Setup Time to CLK (to guarantee proper counting) 35 60 ns THCE CE Hold Time from CLK (to guarantee proper counting) 0 0 ns THOE OE High Time (guarantees counter is reset) 25 25 ns FMAX Maximum Input Clock Frequency 10 10 MHz Notes: 0 Min 0 55 ns 55 ns 1. Preliminary specifications for military operating range only. 2. AC test lead = 50 pF. 3. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. AC Characteristics for AT17LV65/128/256 when Cascading VCC = 3.3V ± 10% Commercial Symbol Description TCDF(3) CLK to Data Float Delay TOCK(2) TOCE(2) TOOE(2) FMAX Notes: 12 Max Units 60 60 ns CLK to CEO Delay 55 60 ns CE to CEO Delay 55 60 ns RESET/OE to CEO Delay 40 45 ns Maximum Input Clock Frequency Min 8 Max Industrial/Military(1) Min 8 MHz 1. Preliminary specifications for military operating range only. 2. AC test lead = 50 pF. 3. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. AT17C/LV65/128/256 1636E–12/01 AT17C/LV65/128/256 Thermal Resistance Coefficients(1) θJC [°C/W] θJA [°C/W] Airflow = 0 ft/min 8CN4 45 115.71 Plastic Dual Inline Package (PDIP) 8P3 37 107 Plastic Gull Wing Small Outline (SOIC) 8S1 45 150 Plastic Leaded Chip Carrier (PLCC) 20J 35 90 Package Type Leadless Array Package (LAP) Note: 1. For more information refer to the “Thermal Characteristics of Atmel’s Packages”, available on the Atmel web site, at http://www.atmel.com/atmel/acrobat/doc0636.pdf. 13 1636E–12/01 Ordering Information – 5V Devices(1) Memory Size Ordering Code Package Operation Range 64-Kbit AT17C65-10CC AT17C65-10PC AT17C65-10NC AT17C65-10JC 8CN4 8P3 8S1 20J Commercial (0°C to 70°C) AT17C65-10CI AT17C65-10PI AT17C65-10NI AT17C65-10JI 8CN4 8P3 8S1 20J Industrial (-40°C to 85°C) AT17C128-10CC AT17C128-10PC AT17C128-10NC AT17C128-10JC 8CN4 8P3 8S1 20J Commercial (0°C to 70°C) AT17C128-10CI AT17C128-10PI AT17C128-10NI AT17C128-10JI 8CN4 8P3 8S1 20J Industrial (-40°C to 85°C) AT17C256-10CC AT17C256-10PC AT17C256-10NC AT17C256-10JC 8CN4 8P3 8S1 20J Commercial (0°C to 70°C) AT17C256-10CI AT17C256-10PI AT17C256-10NI AT17C256-10JI 8CN4 8P3 8S1 20J Industrial (-40°C to 85°C) 128-Kbit 256-Kbit Note: 1. Currently there are two types of low-density configurators. The new version will be identified by a “B” after the date code. Only the “B” version is available in the 8-lead SOIC devices. The “B” version is fully backward-compatible with the original devices so existing customers will not be affected. The new parts no longer require a mux for ISP. See the programming specification for more details. Package Type 8CN4 8-lead, 6 mm x 6 mm x 1 mm, Leadless Array Package (LAP) – Pin-compatible with 8-lead SOIC/VOID Packages 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 20J 20-lead, Plastic J-leaded Chip Carrier (PLCC) 14 AT17C/LV65/128/256 1636E–12/01 AT17C/LV65/128/256 Ordering Information – 3.3V Devices(1) Memory Size Ordering Code Package Operation Range 64-Kbit AT17LV65-10CC AT17LV65-10PC AT17LV65-10NC AT17LV65-10JC 8CN4 8P3 8S1 20J Commercial (0°C to 70°C) AT17LV65-10CI AT17LV65-10PI AT17LV65-10NI AT17LV65-10JI 8CN4 8P3 8S1 20J Industrial (-40°C to 85°C) AT17LV128-10CC AT17LV128-10PC AT17LV128-10NC AT17LV128-10JC 8CN4 8P3 8S1 20J Commercial (0°C to 70°C) AT17LV128-10CI AT17LV128-10PI AT17LV128-10NI AT17LV128-10JI 8CN4 8P3 8S1 20J Industrial (-40°C to 85°C) AT17LV256-10CC AT17LV256-10PC AT17LV256-10NC AT17LV256-10JC 8CN4 8P3 8S1 20J Commercial (0°C to 70°C) AT17LV256-10CI AT17LV256-10PI AT17LV256-10NI AT17LV256-10JI 8CN4 8P3 8S1 20J Industrial (-40°C to 85°C) 128-Kbit 256-Kbit Note: 1. Currently there are two types of low-density configurators. The new version will be identified by a “B” after the date code. Only the “B” version is available in the 8-lead SOIC devices. The “B” version is fully backward-compatible with the original devices so existing customers will not be affected. The new parts no longer require a mux for ISP. See the programming specification for more details. Package Type 8CN4 8-lead, 6 mm x 6 mm x 1 mm, Leadless Array Package (LAP) – Pin-compatible with 8-lead SOIC/VOID Packages 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 20J 20-lead, Plastic J-leaded Chip Carrier (PLCC) 15 1636E–12/01 Packaging Information 8CN4 – LAP Marked Pin1 Indentifier E A A1 D Top View Side View Pin1 Corner L1 0.10 mm TYP 8 1 e COMMON DIMENSIONS (Unit of Measure = mm) 2 7 3 6 b 5 4 e1 L Bottom View SYMBOL MIN NOM MAX A 0.94 1.04 1.14 A1 0.30 0.34 0.38 b 0.45 0.50 0.55 D 5.89 5.99 6.09 E 4.89 5.99 6.09 e 1.27 BSC e1 1.10 REF NOTE 1 L 0.95 1.00 1.05 1 L1 1.25 1.30 1.35 1 Note: 1. Metal Pad Dimensions. 11/14/01 R 16 1150 E.Cheyenne Mtn Blvd. Colorado Springs, CO 80906 TITLE 8CN4, 8-lead (6 x 6 x 1.04 mm Body), Lead Pitch 1.27 mm, Leadless Array Package (LAP) DRAWING NO. 8CN4 REV. A AT17C/LV65/128/256 1636E–12/01 AT17C/LV65/128/256 8P3 – PDIP D PIN 1 E1 A B1 SEATING PLANE A1 L B B2 e (4 PLACES) E COMMON DIMENSIONS (Unit of Measure = mm) C eC eB Notes: 1. This package conforms to JEDEC reference MS-001 BA. 2. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). NOM MAX – – 4.318 A1 0.381 – – D 9.144 – 9.652 E 7.620 – 8.255 E1 6.096 – 6.604 B 0.406 – 0.508 B1 1.397 – 1.651 B2 0.762 – 1.143 L 3.175 – 3.429 C 0.203 – 0.356 eB – – 10.922 eC 0.000 – 1.524 e R TITLE 2325 Orchard Parkway 8P3, 8-lead (0.300"/7.62 mm Wide) Plastic Dual San Jose, CA 95131 Inline Package (PDIP) MIN A SYMBOL NOTE Note 2 Note 2 2.540 TYP 09/28/01 DRAWING NO. REV. 8P3 B 17 1636E–12/01 8S1 – SOIC 3 2 1 H N Top View e B A D COMMON DIMENSIONS (Unit of Measure = mm) Side View A2 C L SYMBOL MIN NOM MAX A – – 1.75 B – – 0.51 C – – 0.25 D – – 5.00 E – – 4.00 e E End View NOTE 1.27 BSC H – – 6.20 L – – 1.27 Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012 for proper dimensions, tolerances, datums, etc. 10/10/01 R 18 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) DRAWING NO. REV. 8S1 A AT17C/LV65/128/256 1636E–12/01 AT17C/LV65/128/256 20J – PLCC PIN NO. 1 1.14(0.045) X 45˚ 1.14(0.045) X 45˚ 0.318(0.0125) 0.191(0.0075) IDENTIFIER e E1 E D2/E2 B1 B A2 D1 A1 D A 0.51(0.020)MAX 45˚ MAX (3X) COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-018, Variation AA. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. SYMBOL MIN NOM MAX A 4.191 – 4.572 A1 2.286 – 3.048 A2 0.508 – – D 9.779 – 10.033 D1 8.890 – 9.042 E 9.779 – 10.033 E1 8.890 – 9.042 D2/E2 7.366 – 8.382 B 0.660 – 0.813 B1 0.330 – 0.533 e NOTE Note 2 Note 2 1.270 TYP 10/04/01 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 20J, 20-lead, Plastic J-leaded Chip Carrier (PLCC) DRAWING NO. REV. 20J B 19 1636E–12/01 Atmel Headquarters Atmel Operations Corporate Headquarters Memory 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 487-2600 Europe Atmel SarL Route des Arsenaux 41 Casa Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500 Asia Atmel Asia, Ltd. Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369 Japan Atmel Japan K.K. 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 Atmel Corporate 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 436-4270 FAX 1(408) 436-4314 Microcontrollers Atmel Corporate 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 436-4270 FAX 1(408) 436-4314 Atmel Nantes La Chantrerie BP 70602 44306 Nantes Cedex 3, France TEL (33) 2-40-18-18-18 FAX (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards Atmel Rousset Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4-42-53-60-00 FAX (33) 4-42-53-60-01 RF/Automotive Atmel Heilbronn Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany TEL (49) 71-31-67-0 FAX (49) 71-31-67-2340 Atmel Colorado Springs 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Atmel Grenoble Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France TEL (33) 4-76-58-30-00 FAX (33) 4-76-58-34-80 Atmel Colorado Springs 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Atmel Smart Card ICs Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland TEL (44) 1355-803-000 FAX (44) 1355-242-743 Atmel Configurator Hotline e-mail (408) 436-4119 [email protected] Atmel Configurator e-mail Web Site [email protected] http://www.atmel.com FAQ Available on web site © Atmel Corporation 2001. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. Atme l® is the registered trademark of Atmel. FLEX ® is the registered trademark of Altera Corporation. APEX ™ is the trademark of Altera Corporation; ORCA ® is the registered trademark of Lucent Technologies; Spartan ® is the registered trademark of Xilinx, Inc.; XC3000 ™, XC4000 ™, XC5200™ and Virtex ™ are the trademarks of Xilinx, Inc.; Other terms and product names may be trademarks of others. Printed on recycled paper. 1636E–12/01/xM