ETC TPS77918DGKR

TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
D
D
D
D
D
D
D
D
D
D
Open Drain Power-On Reset With 220-ms
Delay
250-mA Low-Dropout Voltage Regulator
Available in 1.8-V, 2.5-V, 3-V, Fixed Output
and Adjustable Versions
Dropout Voltage Typically 200 mV
at 250 mA (TPS77930)
Ultralow 92-µA Quiescent Current (Typ)
8-Pin MSOP (DGK) Package
Low Noise (55 µVrms) With No Bypass
Capacitor (TPS77918)
2% Tolerance Over Specified Conditions
For Fixed-Output Versions
Fast Transient Response
Thermal Shutdown Protection
See the TPS773xx and TPS774xx Family of
Devices for Active Low Enable
description
TPS779xx
DGK PACKAGE
(TOP VIEW)
FB/SENSE
RESET
EN
GND
1
2
3
4
8
7
6
5
OUT
OUT
IN
IN
TPS77930
DROPOUT VOLTAGE
vs
JUNCTION TEMPERATURE
400
VI = 2.9 V
350
VDO – Dropout Voltage – mV
D
300
IO= 0.25 A
250
200
IO= 0.15 A
150
The TPS779xx is a low-dropout regulator with
integrated power-on reset. The device is capable
100
of supplying 250 mA of output current with a
IO= 0.05 A
dropout of 200 mV (TPS77930). Quiescent
50
current is 92 µA at full load dropping down to 1 µA
when the device is disabled. The device is
0
optimized to be stable with a wide range of output
90 110 130
–50 –30 –10 10
30
50
70
capacitors including low ESR ceramic (10 µF) or
TJ – Junction Temperature – °C
low capacitance (1 µF) tantalum capacitors. The
device has extremely low noise output performance (55 µVrms) without using any added filter capacitors.
TPS779xx is designed to have a fast transient response for larger load current changes.
The TPS779xx is offered in 1.8-V, 2.5-V, and 3-V fixed-voltage versions and in an adjustable version
(programmable over the range of 1.5 V to 5.5 V). Output voltage tolerance is 2% over line, load, and temperature
ranges. The TPS779xx family is available in 8-pin MSOP (DGK) packages.
Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 200 mV
at an output current of 250 mA for 3.3 volt option) and is directly proportional to the output current. Additionally,
since the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent
of output loading (typically 92 µA over the full range of output current, 0 mA to 250 mA). These two key
specifications yield a significant improvement in operating life for battery-powered systems.
The device is enabled when the EN pin is connected to a high-level input voltage. This LDO family also features
a sleep mode; applying a TTL low signal to EN (enable) shuts down the regulator, reducing the quiescent current
to less than 1 µA at TJ = 25°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2000, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
description (continued)
The TPS779xx features an integrated power-on reset, commonly used as a supply voltage supervisor (SVS),
or reset output voltage. The RESET output of the TPS779xx initiates a reset in DSP, microcomputer, or
microprocessor systems at power-up and in the event of an undervoltage condition. An internal comparator in
the TPS779xx monitors the output voltage of the regulator to detect an undervoltage condition on the regulated
output voltage. When OUT reaches 95% of its regulated voltage, RESET will go to a high-impedance state after
a 220 ms delay. RESET will go to low-impedance state when OUT is pulled below 95% (i.e. over load condition)
of its regulated voltage.
AVAILABLE OPTIONS
OUTPUT VOLTAGE
(V)
TJ
– 40°C to 125°C
PACKAGED DEVICES
TYP
MSOP
(DGK)
SYMBOL
3.0
TPS77930DGK
AHY
2.5
TPS77925DGK
AHX
1.8
TPS77918DGK
AHW
Adjustable
1.5 V to 5.5 V
TPS77901DGK†
AHV
† The TPS77901 is programmable using an external resistor divider (see application
information). The DGK package is available taped and reeled. Add an R suffix to the device
type (e.g., TPS77901DGKR).
VI
5
IN
OUT
6
OUT
IN
SENSE
0.1 µF
3
EN
RESET
7
VO
8
1
2
RESET Output
+
GND
10 µF
4
Figure 1. Typical Application Configuration (For Fixed Output Options)
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
functional block diagram—adjustable version
IN
EN
RESET
_
+
OUT
+
_
220 ms Delay
Vref = 1.1834 V
R1
FB/SENSE
R2
GND
External to the device
functional block diagram—fixed-voltage version
IN
EN
RESET
_
+
OUT
+
_
SENSE
220 ms Delay
R1
Vref = 1.1834 V
R2
GND
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
TPS779xx RESET timing diagram
VI
Vres†
Vres
t
VIT +‡
VO
VIT +‡
Threshold
Voltage
VIT –‡
VIT –‡
t
RESET
Output
Output
Undefined
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
220 ms
Delay
220 ms
Delay
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
Output
Undefined
t
† Vres is the minimum input voltage for a valid RESET. The symbol Vres is not currently listed within EIA or JEDEC standards
for semiconductor symbology.
‡ VIT – Trip voltage is typically 5% lower than the output voltage (95%VO) VIT–
to VIT+ is the hysteresis voltage.
Terminal Functions (TPS779xx)
TERMINAL
NAME
NO.
I/O
DESCRIPTION
FB/SENSE
1
I
Feedback input voltage for adjustable device (sense input for fixed options)
RESET
2
O
Reset output
EN
3
I
Enable input
GND
4
Regulator ground
IN
5, 6
I
Input voltage
OUT
7, 8
O
Regulated output voltage
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
detailed description
pin functions
enable (EN)
The EN terminal is an input which enables or shuts down the device. If EN is a logic low, the device will be in
shutdown mode. When EN goes to logic high, then the device will be enabled.
sense (SENSE)
The SENSE terminal of the fixed-output options must be connected to the regulator output, and the connection
should be as short as possible. Internally, SENSE connects to a high-impedance wide-bandwidth amplifier
through a resistor-divider network and noise pickup feeds through to the regulator output. It is essential to route
the SENSE connection in such a way to minimize/avoid noise pickup. Adding RC networks between the SENSE
terminal and VO to filter noise is not recommended because it can cause the regulator to oscillate.
feedback (FB)
FB is an input terminal used for the adjustable-output options and must be connected to an external feedback
resistor divider. The FB connection should be as short as possible. It is essential to route it in such a way to
minimize/avoid noise pickup. Adding RC networks between FB terminal and VO to filter noise is not
recommended because it can cause the regulator to oscillate.
reset (RESET)
The RESET terminal is an open drain, active low output that indicates the status of VO. When VO reaches 95%
of the regulated voltage, RESET will go to a high-impedance state after a 220-ms delay. RESET will go to a
low-impedance state when Vout is below 95% of the regulated voltage. The open-drain output of the RESET
terminal requires a pullup resistor.
absolute maximum ratings over operating junction temperature range (unless otherwise noted)Ĕ
Input voltage range‡, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 13.5 V
Voltage range at EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 16.5 V
Maximum RESET voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 V
Peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Output voltage, VO (OUT, FB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 125°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
ESD rating, HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
‡ All voltage values are with respect to network terminal ground.
DISSIPATION RATING TABLE – FREE-AIR TEMPERATURES
PACKAGE
DGK
θJA
θJC
AIR FLOW
(CFM)
(°C/W)
(°C/W)
TA < 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
0
266.2
3.84
376 mW
3.76 mW/°C
207 mW
150 mW
150
255.2
3.92
392 mW
3.92 mW/°C
216 mW
157 mW
250
242.8
4.21
412 mW
4.12 mW/°C
227 mW
165 mW
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
recommended operating conditions
MIN
MAX
UNIT
Input voltage, VI†
2.7
10
Output voltage range, VO
1.5
5.5
V
0
250
mA
Output current, IO (see Note 1)
V
Operating virtual junction temperature, TJ (see Note 1)
– 40
125
°C
† To calculate the minimum input voltage for your maximum output current, use the following equation: VI(min) = VO(max) + VDO(max load).
NOTE 1: Continuous current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the
device operate under conditions beyond those specified in this table for extended periods of time.
electrical characteristics over recommended operating junction temperature range (TJ = –40°C to
125°C), VI = VO(typ) + 1 V, IO = 1 mA, EN = 5 V, CO = 10 µF (unless otherwise noted)
PARAMETER
TEST CONDITIONS
1.5 V ≤ VO ≤ 5.5 V,
Adjustable voltage
VO
1.5 V ≤ VO ≤ 5.5 V
TJ = 25°C,
2.8 V < VI < 10 V
2.8 V < VI < 10 V
2 5 V Output
2.5
TJ = 25°C,
3.5 V < VI < 10 V
3.5 V < VI < 10 V
3 0 V Output
3.0
TJ = 25°C,
4.0 V < VI < 10 V
4.0 V < VI < 10 V
Output noise voltage
1.8
1.764
2.45
TPS77918
Peak output current
3.06
92
0.005
1
50% duty cycle
µVrms
1.3
400
°C
1
µA
EN = VI
3
µA
FB = 1.5 V
1
µA
EN = VI,
Adjustable voltage
A
mA
144
Standby current
%/V
mV
55
0.9
µA
%/V
0.05
Thermal shutdown junction temperature
VIH
VIL
2.55
2.94
VO = 0 V
2 ms pulse width,
V
3.0
TJ = 25°C
BW = 300 Hz to 100 kHz, TJ = 25°C,
Output current limit
FB input current
1.836
2.5
VO + 1 V < VI ≤ 10 V, TJ = 25°C
VO + 1 V < VI ≤ 10 V
Load regulation
UNIT
1.02VO
125
Output voltage line regulation (∆VO/VO) (see Note 3)
Vn
Io
MAX
VO
TJ = 25°C
Quiescent current (GND current) (see Notes 2 and 4)
TYP
0.98VO
1 8 V Output
1.8
Output voltage
g
(see Notes 2 and 4)
MIN
TJ = 25°C
TJ = 25°C
High level enable input voltage
2
Low level enable input voltage
Enable input current
–1
V
0.7
V
1
µA
Power supply ripple rejection (TPS77318, TPS77418)
f = 1 KHz,
TJ = 25°C
55
dB
NOTES: 2. Minimum input operating voltage is 2.7 V or VO(typ) + 1 V, whichever is greater. Maximum input voltage = 10 V, minimum output
current 1 mA.
3. If VO < 1.8 V then VImax = 10 V, VImin = 2.7 V:
Line Regulation (mV)
+ ǒ%ńVǓ
V
O
ǒ
V
ǒ
If VO > 2.5 V then VImax = 10 V, VImin = Vo + 1 V:
Line Regulation (mV)
+ ǒ%ńVǓ
V
O
Ǔ
* 2.7 V
Imax
100
V
*
ǒ
Imax
100
V
O
)1
1000
ǓǓ
1000
4. IO = 1 mA to 250 mA
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
electrical characteristics over recommended operating junction temperature range (TJ = –40°C to
125°C), VI = VO(typ) + 1 V, IO = 1 mA, EN = 5 V, CO = 10 µF (unless otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
Trip threshold voltage
I(RESET) = 300 µA
VO decreasing
Hysteresis voltage
Measured at VO
Output low voltage
VI = 2.7 V,
V(RESET) = 5 V
Minimum input voltage for valid RESET
Reset
Leakage current
Dropout voltage (see Note 5)
TYP
MAX
UNIT
98%
VO
VO
1.1
92%
V
0.5%
I(RESET) = 1 mA
RESET time-out delay
VDO
MIN
0.15
0.4
V
1
µA
220
3 V Output
IO = 250 mA,
IO = 250 mA
TJ = 25°C
ms
250
mV
475
NOTE 5: IN voltage equals VO(typ) – 100 mV; 1.8 V, and 2.5 V dropout voltage limited by input voltage range limitations (i.e., 3.3 V input voltage
needs to drop to 3.2 V for purpose of this test).
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VO
Output voltage
vs Output current
2, 3
vs Junction temperature
4, 5
Ground current
vs Junction temperature
6
Power supply rejection ratio
vs Frequency
7
Output spectral noise density
vs Frequency
8
Zo
Output impedance
vs Frequency
9
VDO
Dropout voltage
vs Input voltage
10
vs Junction temperature
11
Line transient response
12, 14
Load transient response
13, 15
Output voltage and enable pulse
vs Time (at startup)
Equivalent series resistance
vs Output current
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
16
18 – 21
7
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
TPS77930
TPS77918
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
3.002
1.802
3.001
1.801
VO – Output Voltage – V
VO – Output Voltage – V
TYPICAL CHARACTERISTICS
3.0
1.800
1.799
2.999
2.998
1.798
0
50
100
150
200
IO – Output Current – mA
0
250
50
100
150
200
IO – Output Current – mA
Figure 2
Figure 3
TPS77930
TPS77918
OUTPUT VOLTAGE
vs
JUNCTION TEMPERATURE
OUTPUT VOLTAGE
vs
JUNCTION TEMPERATURE
1.86
3.05
VI = 2.8 V
VI = 4.3 V
1.84
VO – Output Voltage – V
VO – Output Voltage – V
3.03
IO = 250 mA
3.01
2.99
1.82
1.80
0
40
80
120
TJ – Junction Temperature – °C
140
1.76
–40
0
40
Figure 5
POST OFFICE BOX 655303
80
120
TJ – Junction Temperature – °C
Figure 4
8
IO = 1 mA
IO = 50 mA
IO = 250 mA
1.78
2.97
2.95
–40
250
• DALLAS, TEXAS 75265
140
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TPS779xx
GROUND CURRENT
vs
JUNCTION TEMPERATURE
115
110
Ground Current – µ A
105
100
IO = 1 mA
95
90
85
IO = 250 mA
80
–40
10
60
110
140
TJ – Junction Temperature – °C
Figure 6
TPS77930
TPS77930
POWER SUPPLY REJECTION RATIO
vs
FREQUENCY
OUTPUT SPECTRAL NOISE DENSITY
vs
FREQUENCY
10
Hz
90
IO = 1 mA
Output Spectral Noise Density – µV/
PSRR – Power Supply Rejection Ratio – dB
100
80
70
60
50
40
30
IO = 250 mA
20
10
0
10
100
1k
10k
100k
1M
10M
IO = 250 mA
1
IO = 1 mA
0.1
0.01
100
f – Frequency – Hz
1k
10k
100k
f – Frequency – Hz
Figure 8
Figure 7
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TPS77930
OUTPUT IMPEDANCE
vs
FREQUENCY
10
Zo – Output Impedance – Ω
IO = 1 mA
1
0.1
IO = 250 mA
0.01
10
100
1k
10k
100k
f – Frequency – Hz
1M
10M
Figure 9
TPS77901
TPS77930
DROPOUT VOLTAGE
vs
INPUT VOLTAGE
DROPOUT VOLTAGE
vs
JUNCTION TEMPERATURE
400
400
IO = 250 mA
VI = 2.9 V
TJ = 125 °C
350
TJ = 25 °C
300
VDO – Dropout Voltage – mV
VDO – Dropout Voltage – mV
350
TJ = –40 °C
250
200
150
100
300
IO= 0.25 A
250
200
IO= 0.15 A
150
100
IO= 0.05 A
50
0
2.7
50
3.2
3.7
4.2
VI – Input Voltage – V
4.7
0
–50 –30
Figure 11
Figure 10
10
90
–10 10
30
50
70
TJ – Junction Temperature – °C
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
110
130
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
TPS77918
TPS77918
LINE TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
IO – Output Current – mA
VI – Input Voltage – V
TYPICAL CHARACTERISTICS
3.8
2.8
250
0
∆ VO – Change in
Output Voltage – mV
∆ VO – Change in
Output Voltage – mV
10
0
–10
Co = 10 µF
TJ = 25 °C
IO = 250 mA
0
0.1
0.2 0.3
0.4 0.5 0.6 0.7 0.8
t – Time – ms
0.9
0
–50
Co = 10 µF
TJ = 25 °C
IO = 250 mA
–100
0
1
0.2
0.8 1 1.2 1.4 1.6
t – Time – ms
1.8
2
Figure 13
Figure 12
TPS77930
TPS77930
LINE TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
IO – Output Current – mA
VI – Input Voltage – V
0.4 0.6
5
4
250
0
∆ VO – Change in
Output Voltage – mV
∆ VO – Change in
Output Voltage – mV
10
0
–10
Co = 10 µF
TJ = 25 °C
IO = 250 mA
0
0.1
0.2 0.3
0.4 0.5 0.6 0.7 0.8
t – Time – ms
0.9
1
0
–50
Co = 10 µF
TJ = 25 °C
IO = 250 mA
–100
0
0.1
0.2 0.3
0.4 0.5 0.6 0.7 0.8
t – Time – ms
0.9
1
Figure 15
Figure 14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TPS77930
VO – Output Voltage – V
Enable Pulse – V
OUTPUT VOLTAGE AND
ENABLE PULSE
vs
TIME (AT STARTUP)
EN
0
0
Co = 10 µF
0
0.2 0.4
0.6 0.8 1.0 1.2 1.4 1.6 1.8
t – Time (At Startup) – ms
2.0
Figure 16
VI
To Load
IN
OUT
+
EN
RL
Co
GND
ESR
Figure 17. Test Circuit for Typical Regions of Stability (Figures 18 through 21) (Fixed Output Options)
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
TYPICAL CHARACTERISTICS
TYPICAL REGION OF STABILITY
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
10
Region of Instability
ESR – Equivalent Series Resistance – Ω
ESR – Equivalent Series Resistance – Ω
10
Region of Instability
VO = 3.0 V
Co = 1 µF
VI = 4.3 V
TJ = 25°C
1
Region of Stability
1
Region of Stability
0.1
VO = 3.0 V
Co = 10 µF
VI = 4.3 V
TJ = 25°C
Region of Instability
Region of Instability
0.1
0
50
100
150
200
250
0.01
0
50
100
150
200
250
IO – Output Current – mA
IO – Output Current – mA
Figure 18
Figure 19
TYPICAL REGION OF STABILITY
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
10
10
ESR – Equivalent Series Resistance – Ω
ESR – Equivalent Series Resistance – Ω
Region of Instability
Region of Instability
VO = 3.0 V
Co = 1 µF
VI = 4.3 V
TJ = 125 °C
1
Region of Stability
1
Region of Stability
0.1
VO = 3.0 V
Co = 10 µF
VI = 4.3 V
TJ = 125°C
Region of Instability
Region of Instability
0.01
0.1
0
50
100
150
200
250
0
50
100
150
200
250
IO – Output Current – mA
IO – Output Current – mA
Figure 20
Figure 21
† Equivalent series resistance (ESR) refers to the total series resistance, including the ESR of the capacitor, any series resistance added
externally, and PWB trace resistance to Co.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
external capacitor requirements
An input capacitor is not usually required; however, a bypass capacitor (0.047 µF or larger) improves load
transient response and noise rejection if the TPS779xx is located more than a few inches from the power supply.
A higher-capacitance capacitor may be necessary if large (hundreds of milliamps) load transients with fast rise
times are anticipated.
Most low noise LDOs require an external capacitor to further reduce noise. This will impact the cost and board
space. The TPS779xx has a very low noise specification requirement without using any external component.
Like all low dropout regulators, the TPS779xx requires an output capacitor connected between OUT (output
of the LDO) and GND (signal ground) to stabilize the internal control loop. The minimum recommended
capacitance value is 1 µF provided the ESR meets the requirement in Figures 19 and 21. In addition, a low-ESR
capacitor can be used if the capacitance is at least 10 µF and the ESR meets the requirements in Figures 18
and 20. Solid tantalum electrolytic, aluminum electrolytic, and multilayer ceramic capacitors are all suitable,
provided they meet the requirements described previously.
Ceramic capacitors have different types of dielectric material with each exhibiting different temperature and
voltage variation. The most common types are X5R, X7R, Y5U, Z5U, and NPO. The NPO type ceramic type
capacitors are generally the most stable over temperature. However, the X5R and X7R are also relatively stable
over temperature (with the X7R being the more stable of the two) and are therefore acceptable to use. The Y5U
and Z5U types provide high capacitance in a small geometry, but exhibit large variations over temperature;
therefore, the Y5U and Z5U are not generally recommended for use on this LDO. Independent of which type
of capacitor is used, one must make certain that at the worst case condition the capacitance/ESR meets the
requirement specified in Figures 18 through 21.
Figure 22 shows the output capacitor and its parasitic impedances in a typical LDO output stage.
IO
LDO
–
VESR
RESR
+
+
VI
RLOAD
VO
–
Co
Figure 22. – LDO Output Stage With Parasitic Resistances ESR
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
external capacitor requirements (continued)
In steady state (dc state condition), the load current is supplied by the LDO (solid arrow) and the voltage across
the capacitor is the same as the output voltage (V(Co) = VO). This means no current is flowing into the Co branch.
If IO suddenly increases (transient condition), the following occurs:
D
D
The LDO is not able to supply the sudden current need due to its response time (t1 in Figure 23). Therefore,
capacitor Co provides the current for the new load condition (dashed arrow). Co now acts like a battery with
an internal resistance, ESR. Depending on the current demand at the output, a voltage drop will occur at
RESR. This voltage is shown as VESR in Figure 22.
When Co is conducting current to the load, initial voltage at the load will be VO = V(Co) – VESR. Due to the
discharge of Co, the output voltage VO will drop continuously until the response time t1 of the LDO is reached
and the LDO will resume supplying the load. From this point, the output voltage starts rising again until it
reaches the regulated voltage. This period is shown as t2 in Figure 23.
The figure also shows the impact of different ESRs on the output voltage. The left brackets show different levels
of ESRs where number 1 displays the lowest and number 3 displays the highest ESR.
From above, the following conclusions can be drawn:
D
D
The higher the ESR, the larger the droop at the beginning of load transient.
The smaller the output capacitor, the faster the discharge time and the bigger the voltage droop during the
LDO response period.
conclusion
To minimize the transient output droop, capacitors must have a low ESR and be large enough to support the
minimum output voltage requirement.
IO
VO
1
2
ESR 1
3
ESR 2
ESR 3
t1
t2
Figure 23. – Correlation of Different ESRs and Their Influence to the Regulation of VO at a
Load Step From Low-to-High Output Current
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
programming the TPS77901 adjustable LDO regulator
The output voltage of the TPS77901 adjustable regulator is programmed using an external resistor divider as
shown in Figure 24. The output voltage is calculated using:
V
O
ǒ) Ǔ
+ Vref
1
R1
R2
(1)
Where:
Vref = 1.1834 V typ (the internal reference voltage)
Resistors R1 and R2 should be chosen for approximately 50-µA divider current. Lower value resistors can be
used but offer no inherent advantage and waste more power. Higher values should be avoided as leakage
currents at FB increase the output voltage error. The recommended design procedure is to choose
R2 = 30.1 kΩ to set the divider current at 50 µA and then calculate R1 using:
R1
+
ǒ Ǔ
V
V
O
ref
*1
(2)
R2
OUTPUT VOLTAGE
PROGRAMMING GUIDE
TPS77x01
VI
RESET
IN
0.1 µF
OUTPUT
VOLTAGE
RESET Output
250 kΩ
EN
OUT
VO
R1
FB/SENSE
GND
Co
R1
R2
UNIT
2.5 V
33.5
30.1
kΩ
3.3 V
53.8
30.1
kΩ
3.6 V
61.5
30.1
kΩ
NOTE: To reduce noise and prevent
oscillation, R1 and R2 need to be as close
as possible to the FB/SENSE terminal.
R2
Figure 24. TPS77901 Adjustable LDO Regulator Programming
regulator protection
The TPS779xx PMOS-pass transistor has a built-in back diode that conducts reverse currents when the input
voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the
input and is not internally limited. When extended reverse voltage is anticipated, external limiting may be
appropriate.
The TPS779xx also features internal current limiting and thermal protection. During normal operation, the
TPS779xx limits output current to approximately 0.9 A. When current limiting engages, the output voltage scales
back linearly until the overcurrent condition ends. While current limiting is designed to prevent gross device
failure, care should be taken not to exceed the power dissipation ratings of the package. If the temperature of
the device exceeds 150°C(typ), thermal-protection circuitry shuts it down. Once the device has cooled below
130°C(typ), regulator operation resumes.
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
APPLICATION INFORMATION
power dissipation and junction temperature
Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature
should be restricted to 125°C under normal operating conditions. This restriction limits the power dissipation
the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than
or equal to PD(max).
The maximum-power-dissipation limit is determined using the following equation:
P
D(max)
* TA
+ TJmax
R
qJA
Where:
TJmax is the maximum allowable junction temperature.
RθJA is the thermal resistance junction-to-ambient for the package, i.e., 266.2°C/W for the 8-terminal
MSOP with no airflow.
TA is the ambient temperature.
ǒ
Ǔ
The regulator dissipation is calculated using:
P
D
+ VI * VO
I
O
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation will trigger the
thermal protection circuit.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
TPS77901, TPS77918, TPS77925, TPS77930
250-mA LDO REGULATOR WITH INTEGRATED RESET IN A MSOP8 PACKAGE
SLVS283D – MARCH 2000 – REVISED OCTOBER 2000
MECHANICAL DATA
DGK (R-PDSO-G8)
PLASTIC SMALL-OUTLINE PACKAGE
0,38
0,25
0,65
8
0,25 M
5
0,15 NOM
3,05
2,95
4,98
4,78
Gage Plane
0,25
1
0°– 6°
4
3,05
2,95
0,69
0,41
Seating Plane
1,07 MAX
0,15
0,05
0,10
4073329/B 04/98
NOTES: A.
B.
C.
D.
18
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion.
Falls within JEDEC MO-187
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2002, Texas Instruments Incorporated