AS-Interface Master 60 115 K1 93 100* ... 107* K2 K3 K4 Connection Model Number Serial AS-Interface master VAM-CTR-KF-R AS-i D-SUB 1 Features • Stand-alone master with integrated PLC functionality 5 6 9 RS 232 • Two-digit LCD RS 232 GND 5 TxD 3 RxD 2 Housing Terminal RS 422 Z 9 Y 4 B 8 A 3 Housing 1 Terminal RS 485 A 3 B 8 Housing T erminal 27 26 25 35 Solderside • Powered via AS-Interface • Automatic baud rate detection • Programs slave addresses via mode/set buttons AS-i 5 • Display of detected slaves AS-i + • Error diagnostics via LEDs and LCD AS-i - • Programming and monitoring software • Power Rail connection 2 leads for the bus system AS-i + AS-i - 23 32 4 24 33 Power Rail AS-i + AS-i - D-SUB 3 8 4 9 1 25 26 27 34 35 36 1 A B Y Z Screen A B Y Z Screen 5 6 9 RS 422 34 27 26 25 35 Solderside Power Rail insert DIN rail 5 6 9 25 26 35 Solderside End cap 24 Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group · Tel.: Germany (6 21) 7 76-11 11 · USA (3 30) 4 25 35 55 · Singapore 7 79 90 91 · Internet http://www.pepperl-fuchs.com Date of Issue 01.03.2000 1 Software Technical Data: Model Numbers VAM-CTR-KF-R2 (with RS 232-Interface) VAM-CTR-KF-R3 (with RS 422-Interface) VAM-CTR-KF-R4 (with RS 485-Interface) RS 232C-Interface baud rate 1200, 2400, 4800, 9600, 19200, 38400 or 57600 baud, automatic detection from AS-Interface ≤ 150 Operating voltage UB Operating current Ie [mA] Indicators Address indication, error signals Power ON (power) Serial communications active (ser active) Configuration error (config err) AS-Interface voltage OK (U AS-Interface) Normal AS-Interface operation (AS-Interface active) Automatic addressing possible Projected mode active Buttons [V] Isolation voltage Ui EMC classification Operating temperature tb [°C] [°C] Storage temperature tl Protection (IEC) Allowable shock and vibration Weight [g] LCD, 2 digit LED green LED green LED red LED green LED green LED green LED yellow 2 (mode/set) ≥ 500 severity 3, EC 801/2-4 -25 ... +70 (-13 ... +158 °F) 0 ... +55 (+32 ... +131 °F) IP 20 screw mounted: b ≤ 30 g, T ≤ 11 ms snap-on mounted: b ≤ 15 g, T ≤ 11 ms screw mounted: f ≤ 55 Hz, a ≤ 1 mm snap-on mounted: f ≤ 55 Hz, a ≤ 0.5 mm 420 The software performs the addressing, programming and monitoring of the AS-Interface network. In addition, it contains an editor that creates programs for the integrated PLC functionality. The software also performs a syntax test to ensure the programming commands are correct. 2 software packages are available: 1. AS-Interface SHELL (for MS-DOS) 2. AS-Interface Control Tools (for Windows 3.x and Windows 95) The full version of the AS-Interface SHELL is included in the package. The accompanying demo version of the AS-i Control Tool permits a complete commissioning of the AS-i circuit. The full version of the AS-i Control Tool is avaibale as an accessory and features an extended diagnostic function as well as a larger program memory for AS-i Control. References German: Handbuch VAM-CTR-KF-R English: Manual VAM-CTR-KF-R The documentation and software are included with the unit. When ordering, please specify the language and indicate the desired number of manuals. Description Accessories The VAM-CTR-KF-R is a stand-alone master with integrated PLC functionality. Only 60 mm wide, the space-saving design with an IP 20 rating is ideal for use in an enclosure. The VAM-CTR-KF-R master offers all the advantages of the KF housing, such as Power Rail connections and removable terminals. The connection to the AS-Interface power supply and network is established through these removable terminals. The serial connection is established through a 9-pin Sub D connector or through the mechanically keyed, removable terminals. VAZ-SW-ACT Full version of the AS-Interface Control Tools. In configuration mode, all detected AS-Interface slaves are displayed on the two-digit LCD. In normal operation, the LCD is blank unless the master detects a faulty AS-Interface slave. There are seven LEDs on the front panel used for diagnostics. UPR-05 Continuous Power Rail including aluminum DIN rail and cover, 2 m long. UPR-E End cap for UPR-05. PR-05 Snap-on Power Rail, 0.5 m long. Date of Issue 01.03.2000 PLC Functionality The VAM-CTR-KF-R has 16 K program storage, 8 K RAM, 1,024 counters and 1,024 timers for the PLC functionality. The master can be operated in ’StandAlone’ mode using the integrated PLC functionality, or can be controlled through the serial interface. The program processing time is 2 ms per one thousand commands. The programming language is a structured text format (instruction list). VAZ-P4-R2 Converter for the direct connection of the VAM-CTR-KF-R4 to an RS 232 port. Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group · Tel.: Germany (6 21) 7 76-11 11 · USA (3 30) 4 25 35 55 · Singapore 7 79 90 91 · Internet http://www.pepperl-fuchs.com 25