ECG002 DATA SHEET HIGH LINEARITY BROADBAND AMPLIFIER DC - 6000 MHz Features Applications Broadband Gain Blocks DC to 6000 MHz 20 dB Gain at 1000 MHz 15 dBm Output P1dB at 1000 MHz 29 dBm Output IP3 at 1000 MHz 3.8 dB Noise Figure at 2000 MHz High Linearity Amplifiers Packages Available (-B) SOT-89 (-C) 85 Mil Micro-X (-F) SOT-363 Description The ECG002 is a high reliability, high linearity, low cost broadband amplifier, optimized for commercial communications. The device is manufactured using in-house developed, advanced Indium Gallium Phosphide Heterojunction Bipolar Transistor (InGaP HBT) technology and is designed for use as a 50 Ohm gain block. The amplifier features excellent VSWR, low noise figure and highly linear performance. Typical OIP3 is +29dBm at 1000MHz. The ECG002 operates from a single voltage supply and requires only two DC-blocking capacitors, a bias resistor and an inductor for operation. The device is ideal for wireless applications and is available in a low cost, surface-mountable plastic 85 mil Micro-X and SOT-89 packages. The ECG002 is designed in the Darlington configuration with direct feedback. Its operation frequency at low end is limited only by the dc blocking capacitor and the RF choke inductor (large values are required in both cases). Electrical Specifications o Test Conditions: Ic = 45 mA, Ta = 25 C SYMBOL F LIMITS PARAMETER MIN. Frequency TYP. DC f f f f f f f f f f f f = 1000MHz = 2000MHz = 3000MHz = 6000MHz = 2000MHz = 1000MHz = 2000MHz = 3000MHz = 6000MHz = 1000MHz = 2000MHz = 3000MHz MAX. 6000 20.0 19.0 17.0 13.0 18.0 15.0 15.0 14.0 12.0 29.0 29.0 29.0 UNIT MHz G Gain (Small Signal) G Gain (Large Signal) P1dB Output Power @ 1dB Compression OIP3 Output Third Order Intercept RL in Input Return Loss, 50 Ohm f = 2000MHz 14.0 dB RL out Output Return Loss, 50 Ohm f = 2000MHz 20.0 dB NF Noise Figure f = 2000MHz 3.8 dB Vde Device Voltage 16.0 3.5 3.9 TEST CONDITION dB dB Note 2 dBm dBm 4.3 Note 1 V Note 1: OIP3 = Pout (by power meter, total 2-tone power) + (IM3(dB))/2) - 3dB Note 2: Pin= -3dBm (Gain at 1dB compression) CAUTION! SENSITIVE ELECTRONIC DEVICE EiC Corp. A Subsidiary of EiC Enterprises, Ltd. www.eiccorp.com 45738 Northport Loop West, Fremont, CA 94538 Phone: (510) 979-8999 Fax: (510) 979-8902 SS-000350-000 Rev J 1 ECG002 DATA SHEET HIGH LINEARITY BROADBAND AMPLIFIER DC - 6000 MHz Absolute Maximum Ratings Device Current RF Power Input Operating Temperature Storage Temperature Junction Temperature 150 12 -40 to +85 -65 to +150 +200 mA dBm °C °C °C Note: Exceeding any of the absolute maximum ratings may cause permanent damage to the device. Micro-X Package Outline (all units are in inches) .014 to .026” .094 to .106” 1 4 2 .017 to .023” 3 .086 to .098” .075 to .095” .052 to .068” .021 to .031” .004 to .008” Pin Definitions Pin # 1 2, 4 3 Pin Definition This pin has a nominal 50 ohm input impedance. It requires a DC blocking capacitor large RFin enough to handle the lowest frequency used. The two ground connections should be directly connected together to the ground plane on Gnd the PCB. The ground connection also serves as a heatsink. This pin has a nominal 50 ohm output impedance. It requires a DC bias of 45mA through a series inductor and a resistor. A bypass capacitor (1.0 micro Farad) on the DC side of the RFout inductor is recommended for providing instantaneous current during a modulated RF signal. Use a DC blocking capacitor on the output with similar requirements as the input side. EiC Corp. A Subsidiary of EiC Enterprises, Ltd. www.eiccorp.com 45738 Northport Loop West, Fremont, CA 94538 Phone: (510) 979-8999 Fax: (510) 979-8902 SS-000350-000 Rev J 2 ECG002 DATA SHEET HIGH LINEARITY BROADBAND AMPLIFIER DC - 6000 MHz SOT-89 Package Outline SYMBOL (all units are in inches) A B B1 C D D1 E E1 e E1 F H Inches MIN. MAX. .055 .063 .017 .022 .014 .019 .014 .017 .173 .181 .064 .072 .090 .102 .084 .090 .059 .118 .035 .047 .155 .167 Pin Definitions Pin # 1 2, 4 3 Pin Definition This pin has a nominal 50 ohm input impedance. It requires a DC blocking capacitor large RFin enough to handle the lowest frequency used. The two ground connections should be directly connected together to the ground plane on Gnd the PCB. The ground connection also serves as a heatsink. This pin has a nominal 50 ohm output impedance. It requires a DC bias of 45mA through a series inductor and a resistor. A bypass capacitor (1.0 micro Farad) on the DC side of the RFout inductor is recommended for providing instantaneous current during a modulated RF signal. Use a DC blocking capacitor on the output with similar requirements as the input side. EiC Corp. A Subsidiary of EiC Enterprises, Ltd. www.eiccorp.com 45738 Northport Loop West, Fremont, CA 94538 Phone: (510) 979-8999 Fax: (510) 979-8902 SS-000350-000 Rev J 3 ECG002 DATA SHEET HIGH LINEARITY BROADBAND AMPLIFIER DC - 6000 MHz SOT-363 Package Outline RFout GND GND Pin# Function 1, 2, 4, 5 Ground 3 RF In 6 RF Out 6 . 1 5 4 2 3 GND GND RFin D Milimeters L L1 E1 MIN. E e C e1 A2 b A1 Inches MAX. MIN. MAX. A 0.80 1.20 .031 .047 A1 0.05 0.15 .002 .006 A2 0.80 1.05 .031 .041 b 0.15 0.40 .006 .016 C 0.09 0.18 .004 .007 D 1.80 2.20 .071 .087 E 1.15 1.35 .045 .053 E1 1.80 2.40 .071 .094 e 0.65 BSC. .0256 BSC. e1 1.30 BSC. .0512 BSC. L 0.10 0.30 .004 .012 L1 0.275 0.575 .011 .023 Evaluation Board Materials (SOT-363) QTY 2 1 1 1 2 1 DESIGNATOR C1, C2 C3 R1 L1 J1, J2 VALUE 100pF 1.0uF 47 Ω 100 nH --- DESCRIPTION CAPACITOR, 0603 CAPACITOR, 0603 RESISTOR, 0603 INDUCTOR, 0805 SMA CONNECTOR IC, ECG002F MANUFACTURER &P/N MARUWA CE101J1NO MARUWA CE105K1NR ROHM MCR03J470 TOKO LL2012-FR10K EF JOHNSON 142-0701-881 EiC Corp RED --- 20 GA, WIRE 1.0” ANY BLACK --- 20 GA, WIRE 1.0” ANY --- PCB EiC Corp 60-000445-000A NOTE 1 NOTE 1 NOTE 1 NOTE 1 NOTE 1 SEE DETAIL A SEE DETAIL A 1. EiC RECOMMENDED COMPONENTS ARE SHOW. EQUIVALENT COMPONENTS MAY BE USED. 2. LARGER VALUES GIVE BETTER LOW FREQUENCY RESPONSE(<500MHz) NOTES: UNLESS OTHERWISE SPECIFIED EiC Corp. A Subsidiary of EiC Enterprises, Ltd. www.eiccorp.com 45738 Northport Loop West, Fremont, CA 94538 Phone: (510) 979-8999 Fax: (510) 979-8902 SS-000350-000 Rev J 4 ECG002 DATA SHEET HIGH LINEARITY BROADBAND AMPLIFIER DC - 6000 MHz Evaluation Board Schematic SOT-89, Micro-X and SOT-363 Recommended Bias Resistor Values R = (Vcc-Vde)/Icc = (Vcc-3.9)/0.045 Approximate Supply Voltage (Vcc ) based on standard values for R1 R1 (Ohms) 5 6 7 8 24 47 68 91 9 10 110 130 Ωµ Ωµ Evaluation Board Layout SOT-89 and Micro-X Evaluation Board Materials QTY 2 1 1 1 2 1 DESIGNATOR C1, C2 C3 R1 L1 J1, J2 VALUE 100pF 1.0uF 47 Ω 100 nH --- DESCRIPTION CAPACITOR, 0603 CAPACITOR, 0603 RESISTOR, 0603 INDUCTOR, 0805 SMA CONNECTOR IC, ECG002B, C MANUFACTURER &P/N MARUWA CE101J1NO MARUWA CE105K1NR ROHM MCR03J470 TOKO LL2012-FR10K EF JOHNSON 142-0701-881 EiC Corp RED --- 20 GA, WIRE 1.0” ANY BLACK --- 20 GA, WIRE 1.0” ANY --- PCB EiC Corp 60-000009-003B NOTE 1 NOTE 1 NOTE 1 NOTE 1 NOTE 1 SEE DETAIL A SEE DETAIL A 1. EiC RECOMMENDED COMPONENTS ARE SHOW. EQUIVALENT COMPONENTS MAY BE USED. 2. LARGER VALUES GIVE BETTER LOW FREQUENCY RESPONSE(<500MHz) NOTES: UNLESS OTHERWISE SPECIFIED EiC Corp. A Subsidiary of EiC Enterprises, Ltd. www.eiccorp.com 45738 Northport Loop West, Fremont, CA 94538 Phone: (510) 979-8999 Fax: (510) 979-8902 SS-000350-000 Rev J 5 ECG002 DATA SHEET HIGH LINEARITY BROADBAND AMPLIFIER DC - 6000 MHz Figure 1 Vde vs. Icc (IC Tested on Eval Board) 160 140 120 Icc (mA) 100 +25C 80 -40C +85C 60 40 20 0 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 Vde (V) Figure 2 P1dB vs. Frequency (IC Tested on Eval Board) 20 18 16 P1dB (dBm) 14 12 +25C 10 -40C +85C 8 6 4 2 0 0 500 1000 1500 2000 2500 3000 3500 Frequency (MHz) EiC Corp. A Subsidiary of EiC Enterprises, Ltd. www.eiccorp.com 45738 Northport Loop West, Fremont, CA 94538 Phone: (510) 979-8999 Fax: (510) 979-8902 SS-000350-000 Rev J 6 ECG002 DATA SHEET HIGH LINEARITY BROADBAND AMPLIFIER DC - 6000 MHz Figure 3 Gain vs. Frequency (IC Tested on Eval Board) 25 20 S21 (dB) 15 +25C -40C +85C 10 5 0 0 500 1000 1500 2000 2500 3000 3500 Frequency (MHz) Figure 4 Gain vs. Frequency, T=25 degree C (IC Tested in a 50 Ohm Fixture) 25 20 S21 (dB) 15 10 5 0 0 1 2 3 4 5 6 7 Frequency (GHz) EiC Corp. A Subsidiary of EiC Enterprises, Ltd. www.eiccorp.com 45738 Northport Loop West, Fremont, CA 94538 Phone: (510) 979-8999 Fax: (510) 979-8902 SS-000350-000 Rev J 7 ECG002 DATA SHEET HIGH LINEARITY BROADBAND AMPLIFIER DC - 6000 MHz Figure 5 S11, S22 vs. Frequency, T=25 degree C (IC Tested in a 50 Ohm Fixture) 0 -5 S11, S22 (dB) -10 S11 -15 -20 S22 -25 -30 0 1 2 3 4 5 6 7 6 7 Frequency (GHz) Figure 6 Reverse Isolation vs. Frequency, T=25 degree C (IC Tested in a 50 Ohm Fixture) 0 -5 S12 (dB) -10 -15 -20 -25 0 1 2 3 4 5 Frequency (GHz) EiC Corp. A Subsidiary of EiC Enterprises, Ltd. www.eiccorp.com 45738 Northport Loop West, Fremont, CA 94538 Phone: (510) 979-8999 Fax: (510) 979-8902 SS-000350-000 Rev J 8 ECG002 DATA SHEET HIGH LINEARITY BROADBAND AMPLIFIER DC - 6000 MHz Figure 7 OIP3 vs. Frequency (IC Tested on Eval Board) 35 30 Output IP3 (dBm) 25 20 +25C -40C +85C 15 10 5 0 0 500 1000 1500 2000 2500 3000 3500 Frequency (MHz) Figure 8 Noise Figure vs. Frequency (IC Tested on Eval Board) 4.5 4 3.5 Noise Figure (dB) 3 2.5 2 1.5 1 0.5 0 0 500 1000 1500 2000 2500 Frequency (MHz) EiC Corp. A Subsidiary of EiC Enterprises, Ltd. www.eiccorp.com 45738 Northport Loop West, Fremont, CA 94538 Phone: (510) 979-8999 Fax: (510) 979-8902 SS-000350-000 Rev J 9 DATA SHEET ECG002 HIGH LINEARITY BROADBAND AMPLIFIER DC - 6000 MHz APPLICATION NOTES Please visit our website at www.eiccorp.com to view or download the following documents. You may also call our Customer Service to request a hardcopy. Document # Description AP-000192-000 Discussion of Technology and Reliability Enhancements AP-000194-000 Biasing and Performance Enhancements AP-000487-000 Tape and Reel Specifications and Package Drawings AP-000515-000 Voltage Spike Suppression AP-000516-000 Application Note Index EiC Corp. A Subsidiary of EiC Enterprises, Ltd. www.eiccorp.com 45738 Northport Loop West, Fremont, CA 94538 Phone: (510) 979-8999 Fax: (510) 979-8902 SS-000350-000 Rev J 10