ETC IE-703114-MC-EM1

User’s Manual
IE-703114-MC-EM1
In-Circuit Emulator Option Board
Target Device
V850E/IA2
Document No.
Date Published
©
Printed in Japan
U16533EJ1V0UM00 (1st edition)
September 2003 N CP(K)
[MEMO]
2
User’s Manual U16533EJ1V0UM
Windows is either a registered trademark or a trademark of Microsoft Corporation in the United States
and/or other countries.
PC/AT is a trademark of International Business Machines Corporation.
• The information in this document is current as of December, 2002. The information is subject to
change without notice. For actual design-in, refer to the latest publications of NEC Electronics data
sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not
all products and/or types are available in every country. Please check with an NEC Electronics sales
representative for availability and additional information.
• No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may
appear in this document.
• NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from the use of NEC Electronics products listed in this document
or any other liability arising from the use of such products. No license, express, implied or otherwise, is
granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.
• Descriptions of circuits, software and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these
circuits, software and information in the design of a customer's equipment shall be done under the full
responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by
customers or third parties arising from the use of these circuits, software and information.
• While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products,
customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To
minimize risks of damage to property or injury (including death) to persons arising from defects in NEC
Electronics products, customers must incorporate sufficient safety measures in their design, such as
redundancy, fire-containment and anti-failure features.
• NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and
"Specific".
The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC
Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of
each NEC Electronics product before using it in a particular application.
"Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment
and industrial robots.
"Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support).
"Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems and medical equipment for life support, etc.
The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC
Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications
not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to
determine NEC Electronics' willingness to support a given application.
(Note)
(1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its
majority-owned subsidiaries.
(2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as
defined above).
M8E 02. 11-1
User’s Manual U16533EJ1V0UM
3
Regional Information
Some information contained in this document may vary from country to country. Before using any NEC
Electronics product in your application, pIease contact the NEC Electronics office in your country to
obtain a list of authorized representatives and distributors. They will verify:
•
Device availability
•
Ordering information
•
Product release schedule
•
Availability of related technical literature
•
Development environment specifications (for example, specifications for third-party tools and
components, host computers, power plugs, AC supply voltages, and so forth)
•
Network requirements
In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary
from country to country.
[GLOBAL SUPPORT]
http://www.necel.com/en/support/support.html
NEC Electronics America, Inc. (U.S.)
NEC Electronics (Europe) GmbH
NEC Electronics Hong Kong Ltd.
Santa Clara, California
Tel: 408-588-6000
800-366-9782
Duesseldorf, Germany
Tel: 0211-65 03 01
Hong Kong
Tel: 2886-9318
• Sucursal en España
Madrid, Spain
Tel: 091-504 27 87
• Succursale Française
Vélizy-Villacoublay, France
Tel: 01-30-67 58 00
• Filiale Italiana
Milano, Italy
Tel: 02-66 75 41
• Branch The Netherlands
Eindhoven, The Netherlands
Tel: 040-244 58 45
• Tyskland Filial
Taeby, Sweden
Tel: 08-63 80 820
NEC Electronics Hong Kong Ltd.
Seoul Branch
Seoul, Korea
Tel: 02-558-3737
NEC Electronics Shanghai, Ltd.
Shanghai, P.R. China
Tel: 021-6841-1138
NEC Electronics Taiwan Ltd.
Taipei, Taiwan
Tel: 02-2719-2377
NEC Electronics Singapore Pte. Ltd.
Novena Square, Singapore
Tel: 6253-8311
• United Kingdom Branch
Milton Keynes, UK
Tel: 01908-691-133
J03.4
4
User’s Manual U16533EJ1V0UM
INTRODUCTION
Target Readers
This manual is intended for users who wish to design and develop application
systems using the V850E/IA2.
Purpose
This manual is intended to give users an understanding of the basic specifications
and the proper operation of the IE-703114-MC-EM1.
Organization
This manual is broadly divided into the following parts.
• Overview
• Names and functions of components
• Factory settings
• Cautions
• Differences between target device and target interface circuit
How to Read This Manual
It is assumed that the readers of this manual have general knowledge of electrical
engineering, logic circuits, and microcontrollers.
The IE-703114-MC-EM1 is used connected to the IE-V850E-MC in-circuit
emulator. This manual explains the basic setup procedure and switch settings
of the IE-703114-MC-EM1. For the names and functions of the IE-V850E-MC,
and the connection of parts, refer to the IE-V850E-MC, IE-V850E-MC-A User’s
Manual (U14487E), which is a separate volume.
To broadly understand the basic specifications and operation methods
→ Read this manual in the order of the CONTENTS.
To know the operation methods and command functions of the IE-V850E-MC, and
IE-703114-MC-EM1
→ Read the user’s manual of the debugger (sold separately) that is used.
Conventions
Note:
Footnote for item marked with Note in the text
Caution:
Information requiring particular attention
Remark:
Supplementary information
Binary … ×××× or ××××B
Numerical representation:
Decimal … ××××
Hexadecimal … ××××H
Prefix indicating the power of 2 (address space, memory capacity):
10
K (kilo): 2 = 1,024
20
M (mega): 2 = 1,024
User’s Manual U16533EJ1V0UM
2
5
Terminology
The meanings of terms used in this manual are listed below.
Target device
This is the device to be emulated.
Target system
The system (user-built system) to be debugged. This includes the target program and
hardware configured by the user.
Emulation CPU
This is the device that performs emulation of the target device in the IE-V850E-MC.
Related Documents
When using this manual, refer to the following manuals.
The related documents indicated in this publication may include preliminary versions.
However, preliminary versions are not marked as such.
{ Documents related to development tools (user’s manuals)
Product Name
IE-V850E-MC, IE-V850E-MC-A (In-Circuit Emulator)
U14487E
IE-703114-MC-EM1 (In-Circuit Emulator Option Board)
This manual
V850E/IA2 Hardware
U15195E
V850 Series Development Tools (Tutorial Guide)
U14218E
CA850 (Ver.2.50 or Later) (C Compiler Package)
Operation
U16053E
C Language
U16054E
PM plus
U16055E
Assembly Language
U16042E
ID850 (Ver.2.50) (Integrated Debugger)
Operation
To be prepared
SM850 (Ver.2.50) (System Simulator)
Operation
To be prepared
SM850 (Ver.2.00 or Later) (System Simulator)
External Part User Open Interface
Specifications
U14873E
RX850 (Ver.3.13 or Later) (Real-Time OS)
Basics
U13430E
Installation
U13410E
Technical
U13431E
Basics
U13773E
Installation
U13774E
Technical
U13772E
RX850 Pro (Ver.3.13) (Real-Time OS)
RD850 (Ver. 3.01) (Task Debugger)
U13737E
RD850 Pro (Ver. 3.01) (Task Debugger)
U13916E
AZ850 (Ver. 3.10) (System Performance Analyzer)
U14410E
V850 Series Development Tools
(Supporting 32-Bit OS)
(Application Note)
6
Document Number
Tutorial Guide
(Windows Based)
User’s Manual U16533EJ1V0UM
U16544E
CONTENTS
CHAPTER 1 OVERVIEW..........................................................................................................................10
1.1
1.2
1.3
1.4
1.5
1.6
Hardware Configuration .............................................................................................................11
Hardware Specifications (When Connected to IE-V850E-MC)................................................12
System Specifications of IE-703114-MC-EM1 (When Connected to IE-V850E-MC) ..............13
System Configuration.................................................................................................................14
Contents in Carton......................................................................................................................16
Connection Between IE-V850E-MC and IE-703114-MC-EM1...................................................17
CHAPTER 2 NAMES AND FUNCTIONS OF COMPONENTS ............................................................19
2.1
2.2
2.3
2.4
Component Names and Functions of IE-703114-MC-EM1 ......................................................19
Clock Settings .............................................................................................................................21
2.2.1
Clock settings outline..................................................................................................................... 21
2.2.2
Clock setting methods ................................................................................................................... 22
Operation Mode Setting .............................................................................................................26
Power Supply Settings ...............................................................................................................27
2.4.1
2.5
JP2 setting ..................................................................................................................................... 27
Emulation Memory ......................................................................................................................28
2.5.1
Wait setting for emulation memory ................................................................................................ 28
2.5.2
Cautions related to emulation memory .......................................................................................... 29
CHAPTER 3 FACTORY SETTINGS........................................................................................................30
CHAPTER 4 CAUTIONS ..........................................................................................................................31
4.1
4.2
Cautions Related to Pin Termination ........................................................................................31
Cautions Related to Internal RAM .............................................................................................32
CHAPTER 5 DIFFERENCES BETWEEN TARGET DEVICE AND TARGET INTERFACE CIRCUIT ...........33
APPENDIX A DIMENSIONS.....................................................................................................................41
APPENDIX B EXAMPLE OF USE OF CONNECTOR FOR TARGET CONNECTION.....................52
APPENDIX C CONNECTORS FOR TARGET CONNECTION .............................................................53
C.1
C.2
Usage ...........................................................................................................................................53
Cautions on Handling Connectors............................................................................................55
APPENDIX D MOUNTING PLASTIC SPACER......................................................................................56
User’s Manual U16533EJ1V0UM
7
LIST OF FIGURES
Figure No.
Title
Page
1-1
System Configuration .......................................................................................................................................14
1-2
Contents in Carton............................................................................................................................................16
1-3
Connection Between IE-V850E-MC and IE-703114-MC-EM1 .........................................................................17
2-1
IE-703114-MC-EM1 ..........................................................................................................................................19
2-2
Clock Setting Outline ........................................................................................................................................21
2-3
Outline When Using Mounted Internal Clock....................................................................................................23
2-4
Outline When Changing Mounted Crystal Oscillator and Using New Oscillator as Internal Clock ...................24
2-5
Outline When Using Crystal Oscillator on Target System as External Clock ...................................................25
2-6
JP2 Setting (Automatic Switching Setting) .......................................................................................................27
2-7
JP2 setting (When Power from Target System Is Used) ..................................................................................27
4-1
Schematic Diagram of Power Supply Flow.......................................................................................................32
5-1
Pin Equivalent Circuit 1.....................................................................................................................................33
5-2
Pin Equivalent Circuit 2.....................................................................................................................................34
5-3
Pin Equivalent Circuit 3.....................................................................................................................................35
5-4
Pin Equivalent Circuit 4.....................................................................................................................................35
5-5
Pin Equivalent Circuit 5.....................................................................................................................................36
5-6
Pin Equivalent Circuit 6.....................................................................................................................................36
5-7
Pin Equivalent Circuit 7.....................................................................................................................................40
5-8
Pin Equivalent Circuit 8.....................................................................................................................................40
A-1
100-Pin Plastic LQFP (Fine Pitch) (14 × 14).....................................................................................................50
A-2
100-Pin Plastic QFP (14 × 20) ..........................................................................................................................51
C-1
Mounting NQPACK100SD or NQPACK100RB.................................................................................................53
C-2
Mounting Device ...............................................................................................................................................54
C-3
NQPACK100SD or NQPACK100RB and Device Pin .......................................................................................54
D-1
Mounting Method of Plastic Spacer ..................................................................................................................56
8
User’s Manual U16533EJ1V0UM
LIST OF TABLES
Table No
Title
Page
1-1
Hardware Specifications................................................................................................................................... 12
1-2
System Specifications of IE-703114-MC-EM1 (When Connected to IE-V850E-MC) ....................................... 13
2-1
List of Hardware Settings When Setting Clock................................................................................................. 22
2-2
Settings When Using Mounted Internal Clock .................................................................................................. 23
2-3
Settings When Changing Mounted Internal Clock............................................................................................ 24
2-4
Settings When Using External Clock................................................................................................................ 25
4-1
Pins That Cannot Be Emulated ........................................................................................................................ 31
5-1
Corresponding Pins (Pin Equivalent Circuit 1) ................................................................................................. 33
5-2
Corresponding Pins (Pin Equivalent Circuit 2) ................................................................................................. 34
5-3
Corresponding Pins (Pin Equivalent Circuit 3) ................................................................................................. 35
5-4
Corresponding Pins (Pin Equivalent Circuit 4) ................................................................................................. 35
5-5
Corresponding Pins (Pin Equivalent Circuit 5) ................................................................................................. 36
5-6
Corresponding Pins (Pin Equivalent Circuit 6) ................................................................................................. 37
5-7
Corresponding Pins (Pin Equivalent Circuit 7) ................................................................................................. 40
5-8
Corresponding Pins (Pin Equivalent Circuit 8) ................................................................................................. 40
User’s Manual U16533EJ1V0UM
9
CHAPTER 1 OVERVIEW
The IE-703114-MC-EM1 is an option board for the in-circuit emulator IE-V850E-MC.
By connecting the IE-
703114-MC-EM1 to the IE-V850E-MC, hardware and software can be debugged efficiently in system development
using the V850E/IA2.
In this manual, the basic setup procedures and switch settings of the IE-703114-MC-EM1 when connecting it to
the IE-V850E-MC are described.
For the names and functions of the parts of the IE-V850E-MC, and for the
connection of parts, refer to the IE-V850E-MC, IE-V850E-MC-A User’s Manual (U14487E) which is a separate
volume.
10
User’s Manual U16533EJ1V0UM
CHAPTER 1 OVERVIEW
1.1
Hardware Configuration
Optionalsold
hardware
Separately
hardware
In-circuit emulator (IE-V850E-MC)
Option board
(IE-703114-MC-EM1)
IE-V850E-MC can be used as in-circuit emulator for V850E/IA2 by
adding this board.
Separately sold hardware
Extension probeNote
[SC-100SDN]
General-purpose extension probe made by TOKYO ELETECH
CORPORATION.
PC interface board
IE-70000-PCI-IF(-A)
IE-70000-CD-IF-A
These boards are used to connect the IE-V850E-MC-A to a personal
computer. These boards are inserted in the expansion slot of the
personal computer.
IE-70000-PCI-IF(-A): For PCI bus
IE-70000-CD-IF-A: For PCMCIA socket
100-pin GC-GF conversion
adapterNote
(NEXB-2R100SD/RB)
Socket to convert to GF foot pattern when 100-pin GF package is used
Power adapter
(IE-70000-MC-PS-B)
AC adapter dedicated to NEC Electronics in-circuit emulators
Note For further information, contact Daimaru Kogyo Co., Ltd.
Tokyo Electronics Department (TEL +81-3-3820-7112)
Osaka Electronics Department (TEL +81-6-6244-6672)
User’s Manual U16533EJ1V0UM
11
CHAPTER 1 OVERVIEW
1.2
Hardware Specifications (When Connected to IE-V850E-MC)
Table 1-1. Hardware Specifications
Parameter
Value
Target device
µPD703114GC-xxx-8EU (mask ROM version 0.5 mm pitch)
µPD70F3114GC-8EU (flash memory version 0.5 mm pitch)
µPD703114GF-xxx-3BA (mask ROM version 0.65 mm pitch)
µPD70F3114GF-3BA (flash memory version 0.65 mm pitch)
Target interface voltage
VDD = RVDD = AVDD0 = AVDD1 = 5.0 V ±10%
REGIN = 3.0 to 3.6 V
Maximum operating frequency
40 MHz
External dimensions
(Refer to APPENDIX A
DIMENSIONS)
Height
28 mm
Length
229 mm
Width
96 mm
Power consumption
9.1 W (Max.)
Weight
190 g
{ Extremely lightweight and compact.
{ Higher equivalence with target device can be achieved by omitting buffer between signal cables.
{ 8-bit external trace can be performed by connecting external logic probe (included).
{ The following pins can be masked.
RESET, NMI, WAIT
12
User’s Manual U16533EJ1V0UM
CHAPTER 1 OVERVIEW
1.3
System Specifications of IE-703114-MC-EM1 (When Connected to IE-V850E-MC)
Table 1-2. System Specifications of IE-703114-MC-EM1 (When Connected to IE-V850E-MC)
Parameter
Emulation memory capacity
Specification
Internal ROM
128 KB
External memory
4 MB
Execution/pass detection
coverage
Targeting internal ROM
128 KB
Program execution function
Real-time execution
function
Go, Execution from cursor position, Automatic Go, Execution
up to cursor position, Restart, Return-out
Non real-time execution
function
Step-in, Next-over, Slow motion
Break function
Trace function
Other functions
Caution
Event detection break, software break, forcible break, break
by Come function, break when condition is satisfied during
step execution, fail-safe break
Trace conditions
All trace, section trace, qualify trace
Memory capacity
168 bit × 32 K frames
Mapping function, event function, snapshot function, stub
function, register manipulation function, memory
manipulation function, time measurement function, real-time
RAM sampling function
Some of the functions may not be supported depending on the debugger used.
User’s Manual U16533EJ1V0UM
13
CHAPTER 1 OVERVIEW
1.4
System Configuration
The system configuration when connecting the IE-703114-MC-EM1 to the IE-V850E-MC, which is then connected
to a personal computer (PC-9800 series, PC/AT
TM
or compatibles) is shown below.
Figure 1-1. System Configuration
<17>
<5>
<18>
<6>
<7>
<16>
<4>
<8>
<3>
<12>
<13>
<12>
Target
system
<9>
<10>
<14>
<1>, <2>
Target
system
<13>
<15>
<9>
<11>
<10>, <14>
Device
Device
<15>
<14>
Target
system
<11>
<10>
Target system
Remark 1. <1>
Personal computer (PC-9800 series, PC/AT or compatible)
Note
<2>
Debugger (sold separately), device file
<3>
PC interface board (IE-70000-PCI-IF(-A), IE-70000-CD-IF-A: Sold separately)
<4>
PC interface cable (included with IE-V850E-MC)
<5>
In-circuit emulator (IE-V850E-MC: Sold separately)
<6>
In-circuit emulator option board (IE-703114-MC-EM1)
<7>
External logic probe (included)
<8>
Extension probe (SC-100SDN: Sold separately)
<9>
Connector for GC package emulator connection (YQPACK100SD: Included)
<10> Connector for GC package target connection (NQPACK100SD: Included)
<11> GC package device mount cover (HQPACK100SD: Included)
<12> GF package conversion adapter (NEXB-2R100SD/RB: Sold separately)
14
User’s Manual U16533EJ1V0UM
Target
system
CHAPTER 1 OVERVIEW
<13> Connector for GF package emulator connection (YQPACK100RB: Included with NEXB2R100SD/RB)
<14> Connector for GC package target connection (NQPACK100RB: Included with NEXB2R100SD/RB)
<15> GF package device mount cover (HQPACK100RB: Included with NEXB-2R100SD/RB)
<16> Power adapter (IE-70000-MC-PS-B: Sold separately)
<17> 100-V AC power cable (sold separately: Included with IE-70000-MC-PS-B)
<18> 220-V AC power cable (sold separately: Included with IE-70000-MC-PS-B)
Remark 2. The circled areas in the above figure are the enlargements of the connectors for target connection.
Note Obtain the device file from the website of NEC Electronics (http://www.necel.com/micro/)..
User’s Manual U16533EJ1V0UM
15
CHAPTER 1 OVERVIEW
1.5
Contents in Carton
The carton of the IE-703114-MC-EM1 contains the main unit, guarantee card, packing list, and accessory bag.
Make sure that the accessory bag contains this manual and connector accessories. In case of missing or damaged
items, contact an NEC Electronics sales representative or distributor.
Figure 1-2. Contents in Carton
<2> Accessory bag
<1> IE-703114-MC-EM1
<5> IC Socket
NQPACK100SD
<4> Packing list
<6> IC Socket
YQPACK100SD
<7> IC Socket
HQPACK100SD
<3> Guarantee card
<8> Guide pin
YQGUIDE
<1> IE-703114-MC-EM1 × 1
<5> IC socket NQPACK100SD × 1
<2> Accessory bag × 1
<6> IC socket YQPACK100SD × 1
<3> Guarantee card × 1
<7> IC socket HQPACK100SD × 1
<4> Packing list × 1
<8> Guide pin YQGUIDE × 4
Check that the accessory bag contains this manual, a packing list, an external logic probe, and a restriction
document.
16
User’s Manual U16533EJ1V0UM
CHAPTER 1 OVERVIEW
1.6
Connection Between IE-V850E-MC and IE-703114-MC-EM1
The procedure for connecting the IE-V850E-MC and IE-703114-MC-EM1 is described below.
Caution
Do not break or bend connector pins.
<1> Remove the pod cover (lower) of the IE-V850E-MC.
<2> Set the PGA socket lever of the IE-703114-MC-EM1 to the OPEN position as shown in Figure 1-3 (b).
<3> Connect the IE-703114-MC-EM1 to the PGA socket at the rear of the pod (refer to Figure 1-3 (c)). When
connecting, position the IE-V850E-MC and IE-703114-MC-EM1 so that they are horizontal.
Spacers can be connected to fix the pod (refer to APPENDIX D MOUNTING PLASTIC SPACER).
<4> Set the PGA socket lever of the IE-703114-MC-EM1 to the CLOSE position as shown in Figure 1-3 (b).
<5> Fix the IE-703114-MC-EM1 between the pod cover (lower) with the nylon rivets supplied with the IE-V850EMC.
Figure 1-3. Connection Between IE-V850E-MC and IE-703114-MC-EM1 (1/2)
(a) Overview
Nylon rivets
Pod cover (upper)
Nylon rivets
IE-703114-MC-EM1
IE-V850E-MC
Pod cover
(lower)
Nylon rivets
User’s Manual U16533EJ1V0UM
17
CHAPTER 1 OVERVIEW
Figure 1-3. Connection Between IE-V850E-MC and IE-703114-MC-EM1 (2/2)
(b) PGA socket lever of IE-703114-MC-EM1
CLOSE
OPEN
(c) Connecting part (IE-703114-MC-EM1)
A1 pin position
: Insertion guide
: IE-V850E-MC insertion area
18
User’s Manual U16533EJ1V0UM
CHAPTER 2 NAMES AND FUNCTIONS OF COMPONENTS
This chapter describes the names, functions, and switch settings of components comprising the IE-703114-MCEM1. For the details of the pod, jumper, and switch positions, etc., refer to the IE-V850E-MC, IE-V850E-MC-A
User’s Manual (U14487E).
2.1
Component Names and Functions of IE-703114-MC-EM1
Figure 2-1. IE-703114-MC-EM1
(a) Top view
(b) Bottom view
Direction of pin 1 of the connector
for target connection
Connector for
target connection
JP1
LD2
LD1
PLL
SW1
JP2
DIRECT
TP1
TP2
TP3
TP4
TP5
TP6
8
7
2
1
µ PD70F3114
1
3
2
4
OSC1
Version
Part No.
No.Exxxxxxxxx Ver.1.xx IE-703114-MC-EM1
Serial No.
CN1 EXTD
Connector for
IE-V850E-MC connection
Emulation memory
User’s Manual U16533EJ1V0UM
19
CHAPTER 2 NAMES AND FUNCTIONS OF COMPONENTS
(1) Test pins (TP1 to TP6)
To leave the DMA cycle in the tracer, or to set a break, connect these pins to the external logic probe.
• TP1:
• TP2:
• TP3:
• TP4:
• TP5:
• TP6:
GND
Test pin for product shipment test
DMAAK0
DMAAK1
DMAAK2
DMAAK3
(2) SW1
This is a switch for clock mode switching (for details, refer to 2.2 Clock Settings).
(3) JP1
This is a jumper for switching the clock supply source (for details, refer to 2.2 Clock Settings).
(4) JP2
This is a jumper for switching the power supply (for details, refer to 2.4 Power Supply Settings).
(5) CN1 EXTD
Connects the external logic probe (included).
(6) LD1 (CKSEL: Green)
This is an LED for indicating the level input to the CKSEL pin. When the target system is not connected, this is lit
or extinguished according to the SW1 setting.
LED Status
When Used as Standalone Unit
When Used in Target System Connection
Lit
SW1 = DIRECT
The CKSEL signal from the target system is high
Extinguished
SW1 = PLL
The CKSEL signal from the target system is low
(7) LD2 (RUN: Yellow)
This is an LED for indicating if a user program is being executed or not.
LED Status
Lit
User program is being executed.
Extinguished
User program is halted.
(8) Connector for IE-V850E-MC connection
This is a connector for connecting the IE-V850E-MC.
(9) Connector for target connection
This is a connector for connecting the target system or the extension probe.
(10) Emulation memory
This is a memory that replaces the memory/memory mapped I/O on the target system (for details, refer to 2.5
Emulation Memory).
20
User’s Manual U16533EJ1V0UM
CHAPTER 2 NAMES AND FUNCTIONS OF COMPONENTS
2.2
Clock Settings
2.2.1 Clock settings outline
The following 3 clock setting methods are available.
For details, refer to 2.2.2 Clock setting methods.
(1) Use the crystal oscillator mounted on OSC1 of the IE-703114-MC-EM1 as the internal clock.
(2) Change the crystal oscillator mounted on OSC1 of the IE-703114-MC-EM1 the replacement oscillator as the
internal clock.
(3) Use the crystal oscillator on the target system as an external clock (clock input from target system).
Caution
When using an external clock, input the clock generated by the crystal oscillator to the X1 pin.
When a clock generated by a crystal/ceramic resonator is used, the emulator does not operate
normally.
Figure 2-2. Clock Setting Outline
IE-703114-MC-EM1
Crystal oscillator
(can be changed)
Internal/external
clock switch
JP1
OSC1
Target system
IC4
X1
Crystal
oscillator
IE-V850E-MC
SW1
PLL/Direct
mode
Emulation
CPU
switching
µ PD70F3114
CKSEL
CLKOUT
User’s Manual U16533EJ1V0UM
21
CHAPTER 2 NAMES AND FUNCTIONS OF COMPONENTS
2.2.2 Clock setting methods
A list of the hardware settings when setting the clock is shown below.
Table 2-1. List of Hardware Settings When Setting Clock
Type of Clock Used
(1) Use crystal oscillator
(OSC1) mounted on
IE-703114-MC-EM1 as
internal clock.
Clock
Source
SelectionNote 1
Internal
OSC1 Crystal
Oscillator
Factory
settings
(4.000 MHz)
JP1 Setting
1
2
Clock
Mode
PLL
(3) Use the crystal oscillator on
the target system as an
external clock.
Internal
Change
(to other than
4.000 MHz)
7
8
Crystal
oscillator can
be either
mounted or not
mounted
PLL
Low-level
input
1
2
PLL
High-level
input
Direct
PLL
PLL
Low-level
input
Direct
Direct
External
CKSEL
PinNote 2
Direct
Direct
(2) Change crystal oscillator
(OSC1) mounted on
IE-703114-MC-EM1 and
use new oscillator as the
internal clock.
SW1
7
8
1
2
PLL
High-level
input
Direct
PLL
PLL
Low-level
input
Direct
Direct
7
8
PLL
High-level
input
Direct
Notes 1. Select the clock source in the clock source selection area in the configuration dialog box on the
debugger.
2. The input setting for the CKSEL pin is made only when a target system is connected. Leave this pin
open when operating the emulator on a standalone basis. The emulator operates according to the SW1
setting.
3. When changing the crystal oscillator on the emulator, choose an oscillator that satisfies the conditions
described below.
Power supply voltage
5V
Output level
CMOS
Type
8-pin type
Pin positions
Pin 1: NC, Pin 4: GND, Pin 5: OUT, Pin 8: VDD
4. For cautions related to using an external clock, refer to the V850E/IA2 Hardware User’s Manual
(U15195E).
Caution Settings other than those described above are prohibited.
22
User’s Manual U16533EJ1V0UM
CHAPTER 2 NAMES AND FUNCTIONS OF COMPONENTS
(1) Using the crystal oscillator (OSC1) mounted on the IE-703114-MC-EM1 as the internal clock
<1> Mount the 4.000 MHz crystal oscillator mounted at factory shipment in the OSC1 socket of the IE-703114MC-EM1 (with the default settings).
<2> Change JP1 as indicated in Table 2-2 (with the default settings).
<3> Set the SW1 and CKSEL pins according to the clock mode to be used, as shown in Table 2-2.
<4> To start up the integrated debugger (ID850), select “Internal” in the clock source selection area in the
configuration dialog box (selection of clock in emulator).
Table 2-2. Settings When Using Mounted Internal Clock
Type of Clock Used
Use crystal oscillator
(OSC1) mounted on
IE-703114-MC-EM1 as
internal clock.
Clock Source
Selection
OSC1 Crystal
Oscillator
Internal
Factory setting
(4.000 MHz)
JP1
Setting
1
Clock
Mode
2
SW1
CKSEL PinNote
PLL
Low-level input
PLL
Direct
PLL
Direct
7
High-level input
8
Direct
Note
The input setting for the CKSEL pin is made only when a target system is connected. Leave this pin open
when operating the emulator on a standalone basis.
Figure 2-3. Outline When Using Mounted Internal Clock
IE-703114-MC-EM1
1-2 shorted
3-4 shorted
5-6 open
7-8 open
JP1
Select
“Internal”
on ID850
IC4
Mounted
crystal oscillator
OSC1
Target system
4 MHz
X1
IE-V850E-MC
Emulation
CPU
Crystal
oscillator
SW1
PLL/Direct
mode
switching
µ PD70F3114
CKSEL
CLKOUT
User’s Manual U16533EJ1V0UM
23
CHAPTER 2 NAMES AND FUNCTIONS OF COMPONENTS
(2) Changing the crystal oscillator (OSC1) mounted on the IE-703114-MC-EM1 and using the new oscillator as the
internal clock
<1> Remove the crystal oscillator (OSC1) that is mounted on the IE-703114-MC-EM1 and mount the oscillator to
be used.
<2> Set JP1 as shown in Table 2-3 (factory settings).
<3> Set the SW1 and CKSEL pins according to the clock mode to be used, as shown in Table 2-3.
<4> Select “Internal” in the clock source selection area in the configuration dialog box on the integrated debugger
(ID850).
Table 2-3. Settings When Changing Mounted Internal Clock
Type of Clock Used
Change the crystal
oscillator mounted on
IE-703114-MC-EM1
and use the new
oscillator as the
internal clock.
Clock Source
Selection
Internal
OSC1 Crystal
Oscillator
JP1
Setting
1 2
Change (to
other than
4.000 MHz)
Clock
Mode
SW1
CKSEL pinNote
PLL
Low-level input
PLL
Direct
PLL
Direct
High-level input
7 8
Direct
Note
The input setting for the CKSEL pin is made only when a target system is connected. Leave this pin open
when operating the emulator on a standalone basis.
Figure 2-4. Outline When Changing Mounted Crystal Oscillator and Using New Oscillator as Internal Clock
IE-703114-MC-EM1
1-2 shorted
3-4 shorted
5-6 open
7-8 open
Select
“Internal”
on ID850
IC4
JP1
Change crystal
oscillator
Target system
OSC1
Other than
4 MHz
X1
IE-V850E-MC
CN2
Emulation
CPU
SW1
PLL/Direct
mode
switching
µ PD70F3114
CKSEL
CLKOUT
24
User’s Manual U16533EJ1V0UM
Crystal
oscillator
CHAPTER 2 NAMES AND FUNCTIONS OF COMPONENTS
(3) Using the target system crystal oscillator as an external clock
<1> Set JP1 as shown in Table 2-4 (factory setting).
<2> Set the SW1 and CKSEL pins according to the clock mode to be used, as shown in Table 2-4.
<3> Select “External” in the clock source selection area in the configuration dialog box on the integrated
debugger (ID850).
Table 2-4. Settings When Using External Clock
Type of Clock Used
Clock Source
Selection
OSC1 Crystal
Oscillator
Use crystal oscillator
on target system as
external clock.
External
Crystal
oscillator can
be either
mounted or not
mounted
JP1
Setting
1 2
Clock
Mode
SW1
PLL
PLL
CKSEL PinNote
Low-level input
Direct
PLL
Direct
High-level input
7 8
Direct
Note The input setting for the CKSEL pin is made only when a target system is connected. Leave this pin open
when operating the emulator on a standalone basis.
Caution
Be sure to input a clock generated by a crystal oscillator to the X1 pin.
When a clock generated by a crystal/ceramic resonator is used, the emulator does not operate
normally.
Figure 2-5. Outline When Using Crystal Oscillator on Target System as External Clock
IE-703114-MC-EM1
1-2 shorted
3-4 shorted
5-6 open
7-8 open
Select
“External”
on ID850
IC4
JP1
Can be either
mounted or
not mounted
Target system
OSC1
X1
IE-V850E-MC
Crystal
oscillator
SW1
PLL/Direct
mode
switching
Emulation
CPU
CKSEL
µ PD70F3114
CLKOUT
User’s Manual U16533EJ1V0UM
25
CHAPTER 2 NAMES AND FUNCTIONS OF COMPONENTS
2.3 Operation Mode Setting
The IE-703114-MC-EM1 supports single-chip mode and ROMless mode, similar to the V850E/IA2. Set these as
follows.
Set as follows in the configuration dialog box mask setting area in accordance with the operation mode used when
the integrated debugger (ID850) is activated.
Operation in ROMless mode:
Select Mode00
Operation in single-chip mode:
Select Mode02
Caution
In ROMless mode, be sure to start mapping emulation memory from address 0H if the
emulator is not connected to the target system.
Emulation of the MODE pin cannot be performed since the input level to the MODE pin is implemented using the
debugger pin mask function in the IE-703114-MC-EM1.
For the settings of the pins on the target system, refer to the V850E/IA2 Hardware User’s Manual (U15195E).
26
User’s Manual U16533EJ1V0UM
CHAPTER 2 NAMES AND FUNCTIONS OF COMPONENTS
2.4
Power Supply Settings
2.4.1 JP2 setting
When JP2 is set as shown in Figure 2-6, the IE-703114-MC-EM1 detects the power supply on the target board
and automatically switches whether the emulator operates on VDD from the target system or the emulator’s internal
power supply. (Factory setting)
Caution
If the JP2 setting is incorrect, the emulator may be damaged.
Figure 2-6. JP2 Setting (Automatic Switching Setting)
JP2Note
2
4
1
3
Set 1 and 2 as shorted, and 3 and 4 as open
Note A relay is used for switching the power supply. Depending on the combinations with the target system, the
relay may repeatedly turn on/off, making a continuous switching sound, when the target system is turned
off. In such a case, set JP2 as shown in Figure 2-7.
When JP2 is set as shown in Figure 2-7, VDD is always supplied from the target system. Note that, with this
setting, the emulator does not operate when the target system is not connected.
Figure 2-7. JP2 setting (When Power from Target System Is Used)
JP2
2
4
1
3
Set 1 and 2 as open, and 3 and 4 as shorted
User’s Manual U16533EJ1V0UM
27
CHAPTER 2 NAMES AND FUNCTIONS OF COMPONENTS
2.5
Emulation Memory
This is a substitute memory used to emulate the memory or memory mapped I/O on the target system (capacity: 4
MB).
The emulation memory is mounted on the IE-703114-MC-EM1.
2.5.1 Wait setting for emulation memory
The data wait, address wait, and idle state for the emulation memory are set as follows.
(1) ID850
Select from the following three types on the configuration screen.
Selection
WAIT MASK
1 WAIT ACCESS
TARGET WAIT
Wait Type
Emulation Memory Access
External Memory Access
Data wait
Fixed to 0 waits
Depends on DWC 0, 1 register setting
WAIT signal masked
Address wait
Fixed to 0 waits
Depends on AWC register setting
Idle state
Fixed to 0 cycles
Depends on BCC register setting
Data wait
Fixed to 1 wait
Depends on DWC 0, 1 register setting
and WAIT signal status
Address wait
Fixed to 0 waits
Depends on AWC register setting
Idle state
Fixed to 0 cycles
Depends on BCC register setting
Data wait
Depends on DWC 0, 1 register setting
However, 1 wait when set to 0 waits
Depends on DWC, 0, 1 register setting
and WAIT signal status
Address wait
Fixed to 0 waits
Depends on ASC register setting
Idle state
Depends on BCC register setting
Depends on BCC register setting
(2) MULTI
Select mask or unmask for WAIT and EMWAIT using the “Pinmask” command.
Selection
WAIT: Mask
EMWAIT: Mask
WAIT: Unmask
EMWAIT: Mask
WAIT: Unmask
EMWAIT: Unmask
28
Wait Type
Emulation Memory Access
External Memory Access
Data wait
Fixed to 0 waits
Depends on DWC 0, 1 register setting
WAIT signal masked
Address wait
Fixed to 0 waits
Depends on AWC register setting
Idle state
Fixed to 0 cycles
Depends on BCC register setting
Data wait
Fixed to 1 wait
Depends on DWC 0, 1 register setting
and WAIT signal status
Address wait
Fixed to 0 waits
Depends on AWC register setting
Idle state
Fixed to 0 cycles
Depends on BCC register setting
Data wait
Depends on DWC 0, 1 register setting
However, 1 wait when set to 0 waits
Depends on DWC 0, 1 register setting
and WAIT signal status
Address wait
Fixed to 0 waits
Depends on AWC register setting
Idle state
Depends on BCC register setting
Depends on BCC register setting
User’s Manual U16533EJ1V0UM
CHAPTER 2 NAMES AND FUNCTIONS OF COMPONENTS
2.5.2 Cautions related to emulation memory
(1) Number of data waits required for emulation memory access
The number of data waits that must be inserted for emulation memory access varies depending on the operating
frequency of the emulator.
4 MHz ≤ Operating frequency < 25 MHz
0 waits
25 MHz ≤ Operating frequency < 40 MHz
1 wait
40 MHz = Operating frequency
2 waits
(2) Bus sizing
Make the bus sizing 16 bits (set BSn0 in the BSC register to 1).
An 8-bit bus cannot be used.
(3) WAIT pin
The number of data waits for the emulation memory is not affected by the WAIT pin.
(4) Address wait
Address waits cannot be inserted in the emulation memory.
When address waits need to be inserted, set as follows.
Number of data waits for CS
space of emulation memory
=
Number of address waits for
external memory or external I/O
+
Number
of
data
waits
for
external memory or external I/O
This setting is effective to make the access speed to the emulation memory equal to that of the external memory
or external I/O to measure the performance, etc.
For how to insert waits in the emulation memory, refer to 2.5.1 Wait setting for emulation memory.
User’s Manual U16533EJ1V0UM
29
CHAPTER 3 FACTORY SETTINGS
Item
Setting
Remark
JP1
2
8
1
7
JP2
JP2Note
2
4
1
3
SW1
Settings other than those shown here are
prohibited.
Setting that detects the power supply on the target
board and switches automatically whether the
emulator operates on VDD from the target system or
on the emulator’s internal power supply.
Set to PLL mode.
PLL
DIRECT
Crystal oscillator
(OSC1)
30
4.000 MHz crystal oscillator is mounted.
The frequency can be changed by changing the
crystal resonator.
User’s Manual U16533EJ1V0UM
CHAPTER 4 CAUTIONS
4.1
Cautions Related to Pin Termination
The following shows the pins that need special processing in the emulator.
For the detailed circuit configuration, refer to CHAPTER 5 DIFFERENCES BETWEEN TARGET DEVICE AND
TARGET INTERFACE CIRCUIT.
(1) Pins that cannot be emulated
The following pins are left open in the emulator, so they cannot be emulated.
Evaluate them by using the target device.
Table 4-1. Pins That Cannot Be Emulated
Pin Name 1
MODE0
MODE1
REGIN
X2
Pin Name 2
−
VPP
−
−
Package
Pin No.
GC (14 × 14)
12
GF (14 × 20)
14
GC (14 × 14)
62
GF (14 × 20)
64
GC (14 × 14)
16
GF (14 × 20)
18
GC (14 × 14)
18
GC (14 × 14)
20
(2) RESET pin
The RESET pin is connected (pulled-up) to VDD via a 33 kΩ resistor.
(3) X1 pin
When using an external clock, the X1 pin is pulled down via a 33 kΩ resistor.
The input to the clock generator is delayed by up to 13.2 ns because it passes through 74HC157 first.
When using an internal clock, this pin is pulled down via a 33 kΩ resister and left open.
(4) CKSEL pin
Pull-up/pull-down can be switched by SW1.
When “PLL” is selected by SW1, this pin is pulled down via a 33 kΩ resistor. When “DIRECT” is selected, it is
pulled up via a 33 kΩ resistor.
User’s Manual U16533EJ1V0UM
31
CHAPTER 4 CAUTIONS
(5) VDD pin
(1) VDD in the target system is used to operate the circuit in the emulator.
(2) When JP2 is set as “1 and 2 open” and “3 and 4 shorted”, the evaluation chip in the emulator operates on
VDD from the target system.
(3) When JP2 is set as “1 and 2 open” and “3 and 4 open”, the emulator recognizes the target system power is
off and operates with the 3.3 V power supply.
Figure 4-1. Schematic Diagram of Power Supply Flow
IE-V850E-MC
IE-703114-MC-EM1
Target system
Emulation
CPU
µ PD70F3114
VDD
Power supply
circuit
Relay
Fixed
Switched automatically
JP2Note
JP2
4.2
2
4
2
4
1
3
1
3
Cautions Related to Internal RAM
In the emulator, the internal RAM is mapped at the 12 KB space 0xFFFC000 to 0xFFFEFFF.
Since the V850E/IA2 is mapped at the 6 KB space 0xFFFC000 to 0xFFFD7FF, the target system is not mapped at
the higher 6 KB space in the internal RAM (0xFFFD800 to 0xFFFEFFF).
Therefore, measures must be taken such as setting access breaks beforehand because if the higher 6 KB space
is accessed, the emulator cannot issue a fail-safe break.
32
User’s Manual U16533EJ1V0UM
CHAPTER 5 DIFFERENCES BETWEEN TARGET DEVICE AND TARGET INTERFACE CIRCUIT
This chapter describes the equivalent circuits in the emulator for signals of the emulator connected to the target
system.
Note that, depending on the processing within the emulator, some pins cannot be emulated (refer to
CHAPTER 4 CAUTIONS).
Figures 5-1 to 5-8 show the equivalent circuits.
Tables 5-1 to 5-8 list the pins corresponding to each equivalent circuit.
Figure 5-1. Pin Equivalent Circuit 1
5V
5V
4.45 V
µ PC358
22 Ω
74VHCT541
IE-V850E-MC
LED (Target)
VDD
1 kΩ
5V
Relay
VDD5
VDD5
Emulation CPU
( µ PD703191)
µ PD70F3114
Table 5-1. Corresponding Pins (Pin Equivalent Circuit 1)
Pin Name 1
VDD
Package
Pin No.
GC (14 × 14)
39, 64, 86
GF (14 × 20)
41, 66, 88
User’s Manual U16533EJ1V0UM
33
CHAPTER 5 DIFFERENCES BETWEEN TARGET DEVICE AND TARGET INTERFACE CIRCUIT
Figure 5-2. Pin Equivalent Circuit 2
PDL0 to PDL15
PDH0 to PDH5
PCT0 to PCT6
PCM0 to PCM1
Emulation CPU
( µ PD703191)
Table 5-2. Corresponding Pins (Pin Equivalent Circuit 2)
Pin Name
1
PDL0
PDL1
PDL2
PDL3
PDL4
PDL5
PDL6
PDL7
PDL8
PDL9
PDL10
PDL11
Pin Name
2
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD8
AD9
AD10
AD11
Package
Pin No.
GC (14 × 14)
40
GF (14 × 20)
42
GC (14 × 14)
41
GF (14 × 20)
43
GC (14 × 14)
42
GF (14 × 20)
44
GC (14 × 14)
43
GF (14 × 20)
45
GC (14 × 14)
44
GF (14 × 20)
46
GC (14 × 14)
45
GF (14 × 20)
47
GC (14 × 14)
46
GF (14 × 20)
48
GC (14 × 14)
47
GF (14 × 20)
49
GC (14 × 14)
48
GF (14 × 20)
50
GC (14 × 14)
49
GF (14 × 20)
51
GC (14 × 14)
50
GF (14 × 20)
52
GC (14 × 14)
51
GF (14 × 20)
53
52
PDL12
AD12
GC (14 × 14)
GF (14 × 20)
54
PDL13
AD13
GC (14 × 14)
53
GF (14 × 20)
55
34
Pin Name
1
PDL14
PDL15
PDH0
PDH1
PDH2
PDH3
PDH4
PDH5
PCT0
PCT1
PCT4
PCT6
Pin Name
2
AD14
AD15
A16
A17
A18
A19
A20
A21
LWR
UWR
RD
ASTB
Package
Pin No.
GC (14 × 14)
54
GF (14 × 20)
56
GC (14 × 14)
55
GF (14 × 20)
57
GC (14 × 14)
56
GF (14 × 20)
58
GC (14 × 14)
57
GF (14 × 20)
59
GC (14 × 14)
58
GF (14 × 20)
60
GC (14 × 14)
59
GF (14 × 20)
61
GC (14 × 14)
60
GC (14 × 14)
62
GC (14 × 14)
61
GC (14 × 14)
63
GC (14 × 14)
65
GF (14 × 20)
67
GC (14 × 14)
66
GF (14 × 20)
68
GC (14 × 14)
67
GF (14 × 20)
69
GC (14 × 14)
68
GF (14 × 20)
70
69
PCM0
WAIT
GC (14 × 14)
GF (14 × 20)
71
PCM1
CLKOUT
GC (14 × 14)
70
GC (14 × 14)
72
User’s Manual U16533EJ1V0UM
CHAPTER 5 DIFFERENCES BETWEEN TARGET DEVICE AND TARGET INTERFACE CIRCUIT
Figure 5-3. Pin Equivalent Circuit 3
VDD5
33 kΩ
Emulation CPU
( µ PD703191)
RESET
Table 5-3. Corresponding Pins (Pin Equivalent Circuit 3)
Pin Name 1
Package
RESET
Pin No.
GC (14 × 14)
19
GF (14 × 20)
21
Figure 5-4. Pin Equivalent Circuit 4
AVSS0, AVSS1,
VSS, VSS3, CVSS
GND
Table 5-4. Corresponding Pins (Pin Equivalent Circuit 4)
Pin Name 1
Pin Name 2
AVSS1
LWR
VSS3
CVSS
VSS
AVSS0
UWR
RD
ASTB
WAIT
Package
Pin No.
GC (14 × 14)
3
GF (14 × 20)
5
GC (14 × 14)
13, 63
GF (14 × 20)
15, 65
GC (14 × 14)
20
GF (14 × 20)
22
GC (14 × 14)
38, 87
GF (14 × 20)
40, 89
GC (14 × 14)
95
GF (14 × 20)
97
User’s Manual U16533EJ1V0UM
35
CHAPTER 5 DIFFERENCES BETWEEN TARGET DEVICE AND TARGET INTERFACE CIRCUIT
Figure 5-5. Pin Equivalent Circuit 5
MODE0, MODE1,
REGIN, X2
OPEN
Table 5-5. Corresponding Pins (Pin Equivalent Circuit 5)
Pin Name 1
Pin Name 2
−
MODE0
MODE1
REGIN
X2
VPP
−
−
Package
Pin No.
GC (14 × 14)
12
GF (14 × 20)
14
GC (14 × 14)
62
GF (14 × 20)
64
GC (14 × 14)
16
GF (14 × 20)
18
GC (14 × 14)
18
GC (14 × 20)
20
Figure 5-6. Pin Equivalent Circuit 6
µ PD70F3114
Remark
36
For the corresponding pin names, refer to Table 5-6.
User’s Manual U16533EJ1V0UM
CHAPTER 5 DIFFERENCES BETWEEN TARGET DEVICE AND TARGET INTERFACE CIRCUIT
Table 5-6. Corresponding Pins (Pin Equivalent Circuit 6) (1/3)
Pin Name 1
Pin Name 2
Pin Name 3
Pin Name 4
−
−
−
AVDD0
−
ANI00
−
ANI01
−
ANI02
−
ANI03
−
ANI04
−
ANI05
−
AVDD1
−
−
−
−
−
−
−
−
−
−
−
−
−
−
ANI10
−
−
−
ANI11
−
−
−
ANI12
−
−
−
ANI13
−
−
−
ANI14
−
−
−
ANI15
−
−
−
ANI16
−
−
−
ANI17
−
−
−
RVDD
−
−
−
REGOUT
−
−
−
SI0
P40
−
−
SO0
P41
−
−
SCK0
P42
−
−
RXD0
P30
−
−
Package
GC (14 × 14)
Pin No.
94
GF (14 × 20)
96
GC (14 × 14)
96
GF (14 × 20)
98
GC (14 × 14)
97
GF (14 × 20)
99
GC (14 × 14)
98
GF (14 × 20)
100
GC (14 × 14)
99
GF (14 × 20)
1
GC (14 × 14)
100
GF (14 × 20)
2
GC (14 × 14)
1
GF (14 × 20)
3
GC (14 × 14)
2
GF (14 × 20)
4
GC (14 × 14)
4
GF (14 × 20)
6
GC (14 × 14)
5
GF (14 × 20)
7
GC (14 × 14)
6
GF (14 × 20)
8
GC (14 × 14)
7
GF (14 × 20)
9
GC (14 × 14)
8
GF (14 × 20)
10
GC (14 × 14)
9
GF (14 × 20)
11
GC (14 × 14)
10
GF (14 × 20)
12
GC (14 × 14)
11
GF (14 × 20)
13
GC (14 × 14)
14
GF (14 × 20)
16
GC (14 × 14)
15
GF (14 × 20)
17
GC (14 × 14)
22
GF (14 × 20)
24
GC (14 × 14)
23
GF (14 × 20)
25
GC (14 × 14)
24
GF (14 × 20)
26
GC (14 × 14)
25
GF (14 × 20)
27
User’s Manual U16533EJ1V0UM
37
CHAPTER 5 DIFFERENCES BETWEEN TARGET DEVICE AND TARGET INTERFACE CIRCUIT
Table 5-6. Corresponding Pins (Pin Equivalent Circuit 6) (2/3)
Pin Name 1
TXD0
SI1
SO1
SCK1
TI2
TO21
TO22
TO23
Pin Name 3
Pin Name 4
−
−
P31
RXD1
−
P32
TXD1
−
P33
ASCK1
INTP20
INTP21
INTP22
INTP23
−
P34
−
P20
−
P21
−
P22
−
P23
TO24
INTP24
P24
−
TCLR2
INTP25
P25
−
TI3
INTP30
TCLR3
TO3
INTP31
P27
−
TIUD10
TO10
P10
−
TCUD10
INTP100
P11
−
TCLR10
INTP101
P12
−
NMI
P00
ESO0
INTP0
P01
−
ESO1
INTP1
P02
−
ADTRG0
INTP2
P03
−
ADTRG1
INTP3
P04
−
INTP4
TO3OFF
P05
−
TO000
38
Pin Name 2
−
−
−
P26
−
−
User’s Manual U16533EJ1V0UM
Package
GC (14 × 14)
Pin No.
26
GF (14 × 20)
28
GC (14 × 14)
27
GF (14 × 20)
29
GC (14 × 14)
28
GF (14 × 20)
30
GC (14 × 14)
29
GF (14 × 20)
31
GC (14 × 14)
30
GF (14 × 20)
32
GC (14 × 14)
31
GF (14 × 20)
33
GC (14 × 14)
32
GF (14 × 20)
34
GC (14 × 14)
33
GF (14 × 20)
35
GC (14 × 14)
34
GF (14 × 20)
36
GC (14 × 14)
35
GF (14 × 20)
37
GC (14 × 14)
36
GF (14 × 20)
38
GC (14 × 14)
37
GF (14 × 20)
39
GC (14 × 14)
71
GF (14 × 20)
73
GC (14 × 14)
72
GF (14 × 20)
74
GC (14 × 14)
73
GF (14 × 20)
75
GC (14 × 14)
74
GF (14 × 20)
76
GC (14 × 14)
75
GF (14 × 20)
77
GC (14 × 14)
76
GF (14 × 20)
78
GC (14 × 14)
77
GF (14 × 20)
79
GC (14 × 14)
78
GF (14 × 20)
80
GC (14 × 14)
79
GF (14 × 20)
81
GC (14 × 14)
80
GF (14 × 20)
82
CHAPTER 5 DIFFERENCES BETWEEN TARGET DEVICE AND TARGET INTERFACE CIRCUIT
Table 5-6. Corresponding Pins (Pin Equivalent Circuit 6) (3/3)
Pin Name 1
TO001
TO002
TO003
TO004
TO005
TO010
TO011
TO012
Pin Name 2
Pin Name 3
Pin Name 4
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
TO013
−
−
−
TO014
−
−
−
TO015
−
−
−
Package
GC (14 × 14)
Pin No.
81
GF (14 × 20)
83
GC (14 × 14)
82
GF (14 × 20)
84
GC (14 × 14)
83
GF (14 × 20)
85
GC (14 × 14)
84
GF (14 × 20)
86
GC (14 × 14)
85
GF (14 × 20)
87
GC (14 × 14)
88
GF (14 × 20)
90
GC (14 × 14)
89
GF (14 × 20)
91
GC (14 × 14)
90
GF (14 × 20)
92
GC (14 × 14)
91
GF (14 × 20)
93
GC (14 × 14)
92
GF (14 × 20)
94
GC (14 × 14)
93
GF (14 × 20)
95
User’s Manual U16533EJ1V0UM
39
CHAPTER 5 DIFFERENCES BETWEEN TARGET DEVICE AND TARGET INTERFACE CIRCUIT
Figure 5-7. Pin Equivalent Circuit 7
(a) When using an external clock
74HC157
µPD70F3114
X1
33 kΩ
(b) When using an internal clock
X1
OPEN
33 kΩ
Table 5-7. Corresponding Pins (Pin Equivalent Circuit 7)
Pin Name 1
X1
Package
Pin No.
GC (14 × 14)
17
GF (14 × 20)
19
Figure 5-8. Pin Equivalent Circuit 8
(a) When selecting PLL via SW1
µPD70F3114
CKSEL
33 kΩ
(b) When selecting DIRECT via SW1
5V
33 kΩ
µ PD70F3114
CKSEL
Table 5-8. Corresponding Pins (Pin Equivalent Circuit 8)
Pin Name 1
CKSEL
40
Package
Pin No.
GC (14 × 14)
21
GF (14 × 20)
23
User’s Manual U16533EJ1V0UM
APPENDIX A DIMENSIONS
(1) IE-V850E-MC + IE-703114-MC-EM1 (Unit: mm)
474.7
55
251.7
58.8
90
166
Top View
46
Pin 1 direction
Side View
27
IE-V850E-MC
IE-703114-MC-EM1
Bottom View
231.3
21.6
96
37.5
15.88
Top View
21.6
User’s Manual U16533EJ1V0UM
41
APPENDIX A DIMENSIONS
(2) SC-100SDN (Unit: mm)
32
32
1
13
13
140
42
User’s Manual U16533EJ1V0UM
APPENDIX A DIMENSIONS
(3) NQPACK100SD (Unit: mm)
[Top view]
2.
R
–
3
C 1.5
2
21.0
0.5 X 24 = 12.0
0.5
5.8
0.3
5.8
13.0
20.2
16.6
Slit width
3 – φ 1.0
+ 0.1
2.5
14.0 – 0
2.5
0.18
0.5
15.0
0.5
0.2
1.85
1.85
9.45
3.7
1.2
5.1
5.5
3.9
[Side view]
[Bottom view]
17.0
14.0
0.2
Slit width
15.0
16.0
9.0
4 – φ 2.0 Projection height 1.8
User’s Manual U16533EJ1V0UM
43
APPENDIX A DIMENSIONS
(4) YQPACK100SD (Unit: mm)
[Top view]
16.6
4
–
0.5
0.5 X 24 = 12.0
5.8
23.0
5.8
13.4
21.0
.2
φ2
2
3 – φ 1.0
R
3.
R
–
–
4
4
10.9
13.3
15.7
2
2.
18.1
[Side view]
3.9
2.2
3.1
7.4
2.3 1.2
2.5
0.25 X 0.3
9.0
3.1
3.7
0.3
0.25
0.4
[Bottom view]
0.2
13.4
44
User’s Manual U16533EJ1V0UM
17.3
14.1
16.1
15.3
C 1.5
APPENDIX A DIMENSIONS
(5) HQPACK100SD (Unit: mm)
[Top view]
16.6
4
5.8
13.4
21.0
23.0
.2
φ2
–
0.5
0.5 X 24 = 12.0
5.8
3.
2
3 – φ 1.0
R
R
2
2.
3.1
7.4
3.9
2.15 1.6
2.3
1.2
[Side view]
0.23
0.58
[Bottom view]
17.3
C 1.5
14.1
17.1
15.12
0.2
13.4
User’s Manual U16533EJ1V0UM
45
APPENDIX A DIMENSIONS
(6) NEXB-2R100SD/RB (Unit: mm)
[Top view]
99
100
1 2
81
82
79
21.55
80
29 30
NEXB-2R100SD/RB
52
51
49
50
32
31
21.55
[Side view]
6.6
9.2
3.2
[Bottom view]
1.2
C2.0
99
100
2 1
38.0
79 80
81
82
1.2
51 52
50
49
32
31
30 29
31.0
46
User’s Manual U16533EJ1V0UM
APPENDIX A DIMENSIONS
(7) NQPACK100RB (Unit: mm)
[Top view]
21.75
0.65 × 19 = 12.35
6.0
3-R1.5
0.4
3- φ 1.0
28.25
23.9
20.75
7.0
0.65
0.65 × 29 = 18.85
C1.5
14.25
17.4
1.85
0.23
6.95
9.45
3.7
3.9
1.2
[Side view]
0.25
15.25
(21.75)
0.5
[Bottom view]
17.15
15.25
10.0
23.65
12.0
21.75
0.5
0.5
4- φ 2.0 (A projection height : 1.8 mm)
User’s Manual U16533EJ1V0UM
47
APPENDIX A DIMENSIONS
(8) YQPACK100RB (Unit: mm)
[Top view]
23.75
17.4
0.65 × 19 = 12.35
0.65
6.0
3-R2.5
16.85
19.25
21.65
24.05
30.25
23.9
0.65 × 29 = 18.85
0.65
7.0
C2.0
3- φ 1.0
4- φ 2.2
10.35
12.75
15.15
17.55
[Side view]
0.25
0.25
0.4
[Bottom view]
14.15
20.2
21.25
0.4
C1.5
14.75
48
0.4
User’s Manual U16533EJ1V0UM
7.4
3.1
2.2
9.9
2.3
3.7
2.5
1.2
0.3
APPENDIX A DIMENSIONS
(9) HQPACK100RB (Unit: mm)
[Top view]
23.75
0.65 × 19 = 12.35
0.65
3-R2.5
6.0
23.9
0.65 × 29 = 18.85
7.0
30.25
0.65
C2.0
3- φ 1.0
4- φ 2.2
17.4
0.25
16.57
(23.07)
7.4
3.1
2.3
2.25
1.2
[Side view]
0.5
[Bottom view]
C1.5
20.2
14.1
User’s Manual U16533EJ1V0UM
49
APPENDIX A DIMENSIONS
The following shows a diagram of the conditions when connecting the in-circuit emulator option board to the
conversion connector. Follow the configuration below and consider the shape of parts to be mounted on the target
system when designing a system.
Figure A-1. 100-Pin Plastic LQFP (Fine Pitch) (14 × 14)
Side view
In-circuit emulator
IE-V850E-MC
In-circuit emulator
option board
IE-703114-MC-EM1
231.3 mm
Note
Target system
Conversion connector
YQGUIDE
YQPACK100SD
NQPACK100SD
Note YQSOCKET100SDN (sold separately) can be inserted here to adjust the height (height: 3.2 mm).
Top view
IE-V850E-MC
Target system
IE-703114-MC-EM1
YQPACK100SD, NQPACK100SD,
YQGUIDE
Connection condition diagram
IE-703114-MC-EM1
Connect to IE-V850E-MC.
75 mm
YQGUIDE
YQPACK100SD
NQPACK100SD
13.3 mm
31.84 mm
17.9955 mm
21.58 mm
28.7445 mm
50
User’s Manual U16533EJ1V0UM
Target system
APPENDIX A DIMENSIONS
Figure A-2. 100-Pin Plastic QFP (14 × 20)
Side view
In-circuit emulator
IE-V850E-MC
In-circuit emulator option board
IE-703114-MC-EM1
Conversion connector
231.3 mm
Note
NEXB-2R100SD/RB
YQGUIDE
YQPACK100RB
NQPACK100RB
Target system
Note YQSOCKET100SDN (sold separately) can be inserted here to adjust the height (height: 3.2 mm).
Top view
IE-V850E-MC
Target system
NEXB-2R100SD/RB
Pin 1 position
IE-703114-MC-EM1
20.7 mm
8 mm
YQPACK100RB, NQPACK100RB,
YQGUIDE
Connection condition diagram
IE-703114-MC-EM1
Connect to IE-V850E-MC.
Pin 1 position
75 mm
NEXB-2R100SD/RB
YQPACK100RB
NQPACK100RB
33.2 mm
38 mm
Target system
20 mm
28.7 mm
18.5 mm
User’s Manual U16533EJ1V0UM
51
APPENDIX B EXAMPLE OF USE OF CONNECTOR FOR TARGET CONNECTION
(1) When directly connecting device to target system (connector for target connection is not used)
Device
Target system
(2) When using device using connector for target connection (GC package)
Fastening screws
(included with HQPACK100SD)
HQPACK100SD
Device
NQPACK100SD
Target system
(3) When using device using connector for target connection (GF package)
Fastening screws
(included with HQPACK100RB)
HQPACK100RB
Device
NQPACK100RB
Target system
52
User’s Manual U16533EJ1V0UM
APPENDIX C CONNECTORS FOR TARGET CONNECTION
C.1 Usage
(1) When mounting NQPACK100SD or NQPACK100RB on target system
<1>
Coat the tip of the four projections (points) at the bottom of the NQPACK100SD or NQPACK100RB with
two-component type epoxy adhesive (cure time longer than 30 min.) and bond the NQPACK100SD or
NQPACK100RB to the target system. If not bonded properly, the pad of the printed circuit board may peel
off when the emulator is removed from the target system. If the leads of the NQPACK100SD is not can be
easily, aligned with the pads of the target system perform step <2> to adjust the position.
<2>
To adjust the position, insert the guide pins for position adjustment (NQGUIDE) provided with the
NQPACK100SD or NQPACK100RB into the pin holes on the upper side of NQPACK100SD or
NQPACK100RB (refer to Figure C-1). The diameter of a hole is φ = 1.0 mm. There are three non-through
holes (refer to APPENDIX A DIMENSIONS).
<3>
After setting the HQPACK100SD or HQPACK100RB, solder the NQPACK100SD or HQPACK100RB to the
target system. By following this sequence, adherence of flux or solder sputtering on the contact pins of the
NQPACK100SD or HQPACK100RB can be avoided.
Recommended soldering conditions… Reflow:
240°C, 20 seconds max.
Partial heating:
<4>
240°C, 10 seconds max. (per pin row)
Remove the guide pins.
Figure C-1. Mounting NQPACK100SD or NQPACK100RB
HQPACK100SD
or HQPACK100RB
Guide pins
(NQGUIDE)
NQPACK100SD
or NQPACK100RB
Target system
Remark
NQPACK100SD or NQPACK100RB:
Connector for target connection
HQPACK100SD or NQPACK100RB:
Cover for device installation
User’s Manual U16533EJ1V0UM
53
APPENDIX C CONNECTORS FOR TARGET CONNECTION
(2) When mounting device
Caution Check for abnormal conditions such as resin burr or bent pins before mounting a device on the
NQPACK100SD or NQPACK100RB. Moreover, check that the hold pins of the HQPACK100SD
or HQPACK100RB are not broken or bent before mounting the HQPACK100SD or
HQPACK100RB. If there are broken or bent pins, fix them with a thin, flat plate such as a blade.
<1>
Make sure that the NQPACK100SD or NQPACK100RB is clean and the device pins are parallel (flat)
before mounting a device on the NQPACK100SD or NQPACK100RB.
Then, after mounting the
NQPACK100SD or NQPACK100RB on the target board, fix the device and the HQPACK100SD or
HQPACK100RB (refer to Figure C-2).
<2>
Using the screws provided with the HQPACK100SD or HQPACK100RB (four locations: M2 × 6 mm),
secure the HQPACK100SD or HQPACK100RB, device, and NQPACK100SD or NQPACK100RB.
Tighten the screws in a crisscross pattern with the screwdriver provided or a driver with a torque gauge
(avoid tightening only one screw strongly). Tighten the screws with 0.55 kg⋅f⋅cm (0.054 N⋅m) max. torque.
Excessive tightening may diminish conductivity.
At this time, each pin is fixed inside the plastic dividers by the contact pin of the NQPACK100SD or
NQPACK100RB and the hold pin of the HQPACK100SD or HQPACK100RB (refer to Figure C-3). Thus,
pins cannot cause shorting with the pins of neighboring devices.
Figure C-2. Mounting Device
Fastening screws
HQPACK100SD
or HQPACK100RB
Device
NQPACK100SD
or NQPACK100RB
Target system
Figure C-3. NQPACK100SD or NQPACK100RB and Device Pin
Hold pin of HQPACK100SD
or HQPACK100RB
Divider
Device
Pin
Contact pin of NQPACK100SD
or NQPACK100RB
54
User’s Manual U16533EJ1V0UM
APPENDIX C CONNECTORS FOR TARGET CONNECTION
C.2 Cautions on Handling Connectors
(1) When taking connectors out of the case, remove the sponge while holding the main unit.
(2) When soldering the NQPACK100SD or NQPACK100RB to the target system, cover it with the HQPACK100SD or
HQPACK100RB for protection against splashing flux.
Recommended soldering conditions… Reflow:
Partial heating:
240°C, 20 seconds max.
240°C, 10 seconds max. (per pin row)
(3) Check for abnormal conditions such as resin burr or bent pins before mounting a device on the NQPACK100SD
or NQPACK100RB. Moreover, when covering with the HQPACK100SD or HQPACK100RB, check that the hold
pins of the HQPACK100SD or HQPACK100RB are not broken or bent before mounting the HQPACK100SD or
HQPACK100RB. If there are broken or bent pins, fix them with a thin, flat plate such as a blade.
(4) When securing the YQPACK100SD or YQPACK100RB (connector for emulator connection) or HQPACK100SD
or HQPACK100RB to the NQPACK100SD or NQPACK100RB with screws, tighten the four screws temporarily
with the screwdriver provided or a driver with a torque gauge, then tighten the screws in a crisscross pattern (with
0.054 N⋅m max. torque).
Excessive tightening of only one screw may diminish conductivity.
If the conductivity is diminished after screw-tightening, stop tightening, remove the screws and make sure the
NQPACK100SD or NQPACK100RB is clean and the device pins are parallel (flat).
(5) Device pins are not strong. Repeatedly connecting to the NQPACK100SD or NQPACK100RB may cause pins to
bend. When mounting a device on NQPACK100SD or NQPACK100RB, check and adjust bent pins.
User’s Manual U16533EJ1V0UM
55
APPENDIX D MOUNTING PLASTIC SPACER
This chapter describes the mounting method for the plastic spacer supplied with the IE-V850E-MC.
When using the emulator connected to the target system, mount the plastic spacer as shown in Figure D-1 to fix
the pod horizontally.
z Mounting plastic spacer on IE-V850E-MC
<1> Remove the nylon rivet from the rear part of the pod.
<2> Tighten the plastic spacer with the plastic screw supplied.
<3> To adjust the height, use a spacer other than the included spacer or a stand.
Figure D-1. Mounting Method of Plastic Spacer
Plastic spacer
Target system
56
User’s Manual U16533EJ1V0UM