ETC ISP1181BS

ISP1181
Full-speed Universal Serial Bus interface device
Rev. 04 — 30 October 2001
Product data
1. General description
The ISP1181 is a Universal Serial Bus (USB) interface device which complies with
Universal Serial Bus Specification Rev. 1.1. It provides full-speed USB
communication capacity to microcontroller or microprocessor-based systems. The
ISP1181 communicates with the system’s microcontroller or microprocessor through
a high-speed general-purpose parallel interface.
The ISP1181 supports fully autonomous, multi-configurable Direct Memory Access
(DMA) operation.
The modular approach to implementing a USB interface device allows the designer to
select the optimum system microcontroller from the wide variety available. The ability
to re-use existing architecture and firmware investments shortens development time,
eliminates risks and reduces costs. The result is fast and efficient development of the
most cost-effective USB peripheral solution.
The ISP1181 is ideally suited for application in many personal computer peripherals,
such as printers, communication devices, scanners, external mass storage (Zip®
drive) devices and digital still cameras. It offers an immediate cost reduction for
applications that currently use SCSI implementations.
2. Features
■ Complies with Universal Serial Bus Specification Rev. 1.1 and most Device Class
specifications
■ High performance USB interface device with integrated Serial Interface Engine
(SIE), FIFO memory, transceiver and 3.3 V voltage regulator
■ High speed (11.1 Mbyte/s or 90 ns read/write cycle) parallel interface
■ Fully autonomous and multi-configuration DMA operation
■ Up to 14 programmable USB endpoints with 2 fixed control IN/OUT endpoints
■ Integrated physical 2462 bytes of multi-configuration FIFO memory
■ Endpoints with double buffering to increase throughput and ease real-time data
transfer
■ Seamless interface with most microcontrollers/microprocessors
■ Bus-powered capability with low power consumption and low ‘suspend’ current
■ 6 MHz crystal oscillator with integrated PLL for low EMI
■ Controllable LazyClock (115 kHz ±10 %) output during ‘suspend’
■ Software controlled connection to the USB bus (SoftConnect™)
■ Good USB connection indicator that blinks with traffic (GoodLink™)
■ Clock output with programmable frequency (up to 48 MHz)
ISP1181
Philips Semiconductors
Full-speed USB interface
■ Complies with the ACPI™, OnNow™ and USB power management requirements
■ Internal power-on and low-voltage reset circuit, with possibility of a software reset
■ Operation over the extended USB bus voltage range (4.0 to 5.5 V) with 5 V
tolerant I/O pads
■ Operating temperature range −40 to +85 °C
■ 8 kV in-circuit ESD protection
■ Full-scan design with high fault coverage
■ Available in TSSOP48 and HVQFN48 packages.
3. Applications
■ Personal digital assistant (PDA)
■ Digital camera
■ Communication device, e.g.,
◆ Router
◆ Modem
■ Mass storage device, e.g.,
◆ Zip drive
■ Printer
■ Scanner.
4. Ordering information
Table 1:
Ordering information
Type number
Package
Name
Description
Version
ISP1181DGG
TSSOP48
Plastic thin shrink small outline package; 48 leads; body width 6.1 mm
SOT362-1
ISP1181BS
HVQFN48
Heat sink very thin profile quad flat package; no leads; 48 terminals;
body 7 × 7 × 0.85 mm
SOT619-3
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
2 of 71
xxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx x xxxxxxxxxxxxxx xxxxxxxxxx xxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx
xxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx xxxxxxxxxxxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxx x x
4
GL
sense
input
to LED
XTAL1
XTAL2
6
7
48
47
3.3 V
DREQ
CLKOUT
HUB
GoodLink
PLL
OSCILLATOR
1.5
kΩ
EOT, DACK
2
11
45
10, 12
to/from
microcontroller
48
MHz
PROGR.
DIVIDER
Philips Semiconductors
6 MHz
D− VBUS
5
5. Block diagram
9397 750 08938
Product data
to/from USB
D+
17
DMA
HANDLER
BUS_CONF0
18
BUS_CONF1
BIT CLOCK
RECOVERY
Rev. 04 — 30 October 2001
SoftConnect
PHILIPS
SIE
ANALOG
Tx/Rx
MEMORY
MANAGEMENT
UNIT
MICRO
CONTROLLER
HANDLER
38, 35 to 27,
24 to 19 16
BUS
INTERFACE
43 to 39
5
AD,
DATA1 to DATA9,
DATA10 to DATA15
CS, ALE, WR,
RD, A0
RESET
VCC
44
internal
reset
POWER-ON
RESET
1
VOLTAGE
REGULATOR
3
3.3 V
9
8
ENDPOINT
HANDLER
INTERNAL
SUPPLY
I/O PIN
SUPPLY
25, 36, 46
37
15
INT
ISP1181
26
MGS767
3
REGGND
SUSPEND WAKEUP
GND
VCC(3.3)
Vref
ISP1181
Fig 1. Block diagram.
Vreg(3.3)
Full-speed USB interface
3 of 71
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
2
3.3 V
INTEGRATED
RAM
ISP1181
Philips Semiconductors
Full-speed USB interface
6. Pinning information
6.1 Pinning
VCC 1
48 XTAL1
REGGND 2
47 XTAL2
Vreg(3.3) 3
46 GND
D− 4
45 CLKOUT
D+ 5
44 RESET
43 CS
VBUS 6
GL 7
42 ALE
WAKEUP 8
41 WR
SUSPEND 9
40 RD
EOT 10
39 A0
DREQ 11
38 AD
37 VCC(3.3)
DACK 12
ISP1181DGG
TEST1 13
36 GND
TEST2 14
35 DATA1
INT 15
34 DATA2
TEST3 16
33 DATA3
BUS_CONF0 17
32 DATA4
BUS_CONF1 18
31 DATA5
DATA15 19
30 DATA6
DATA14 20
29 DATA7
DATA13 21
28 DATA8
DATA12 22
27 DATA9
DATA11 23
26 Vref
DATA10 24
25 GND
MGL892
Fig 2. Pin configuration TSSOP48.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
4 of 71
ISP1181
Philips Semiconductors
23 DATA8
24 DATA7
22 DATA9
20 GND
21 Vref
18 DATA11
19 DATA10
15 DATA14
16 DATA13
17 DATA12
13 BUS_CONF1
14 DATA15
Full-speed USB interface
BUS_CONF0 12
TEST3 11
25 DATA6
26 DATA5
INT 10
9
27 DATA4
28 DATA3
TEST1
8
DACK
7
29 DATA2
30 DATA1
DREQ
6
EOT
5
SUSPEND
4
WAKEUP
3
GL
2
VBUS
1
TEST2
ISP1181BS
33 AD
34 A0
CS 38
ALE 37
CLKOUT 40
RESET 39
XTAL2 42
GND 41
Vreg(3.3) 46
REGGND 45
VCC 44
XTAL1 43
35 RD
36 WR
D+ 48
D− 47
Bottom view
31 GND
32 VCC(3.3)
MBL316
Fig 3. Pin configuration HVQFN48.
6.2 Pin description
Table 2:
Symbol[1]
Pin description
Pin
TSSOP48
Type
Description
HVQFN48
VCC
1
44
-
supply voltage (3.3 or 5.0 V)
REGGND
2
45
-
voltage regulator ground supply
Vreg(3.3)
3
46
-
regulated supply voltage (3.3 V ± 10%)
from internal regulator; used to connect
decoupling capacitor and pull-up resistor on
D+ line;
Remark: Cannot be used to supply external
devices.
D−
4
47
AI/O
USB D− connection (analog)
D+
5
48
AI/O
USB D+ connection (analog)
VBUS
6
1
I
VBUS sensing input
GL
7
2
O
GoodLink LED indicator output (open-drain,
8 mA); the LED is default ON, blinks OFF
upon USB traffic; to connect an LED use a
series resistor of 330 Ω (VCC = 5.0 V) or
250 Ω (VCC = 3.3 V)
WAKEUP
8
3
I
wake-up input (edge triggered,
LOW to HIGH); generates a remote
wake-up from ‘suspend’ state
SUSPEND
9
4
O
‘suspend’ state indicator output (4 mA);
used as power switch control output (active
LOW) for powered-off application
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
5 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 2:
Pin description…continued
Symbol[1]
Pin
Type
Description
5
I
End-Of-Transfer input (programmable
polarity, see Table 22); used by the DMA
controller to force the end of a DMA transfer
to the ISP1181
11
6
O
DMA request output (4 mA; programmable
polarity, see Table 22); signals to the DMA
controller that the ISP1181 wants to start a
DMA transfer
DACK
12
7
I
DMA acknowledge input (programmable
polarity, see Table 22); used by the DMA
controller to signal the start of a DMA
transfer requested by the ISP1181
TEST1
13
8
I
test input; this pin must be connected to
VCC via an external 10 kΩ resistor
TEST2
14
9
I
test input; this pin must be connected to
VCC via an external 10 kΩ resistor
INT
15
10
O
interrupt output; programmable polarity
(active HIGH or LOW) and signalling (level
or pulse); see Table 22
TEST3
16
11
O
test output; this pin is used for test
purposes only
BUS_CONF0
17
12
I
bus configuration selector; see Table 3
BUS_CONF1
18
13
I
bus configuration selector; see Table 3
DATA15
19
14
I/O
bit 15 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
DATA14
20
15
I/O
bit 14 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
DATA13
21
16
I/O
bit 13 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
DATA12
22
17
I/O
bit 12 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
DATA11
23
18
I/O
bit 11 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
DATA10
24
19
I/O
bit 10 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
GND
25
20
-
ground supply
Vref
26
21
-
I/O pin reference voltage (3.3 V); no
connection if VCC = 5.0 V
DATA9
27
22
I/O
bit 9 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
DATA8
28
23
I/O
bit 8 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
DATA7
29
24
I/O
bit 7 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
DATA6
30
25
I/O
bit 6 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
TSSOP48
HVQFN48
EOT
10
DREQ
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
6 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 2:
Symbol[1]
Pin description…continued
Pin
Type
Description
26
I/O
bit 5 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
32
27
I/O
bit 4 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
DATA3
33
28
I/O
bit 3 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
DATA2
34
29
I/O
bit 2 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
DATA1
35
30
I/O
bit 1 of D[15:0]; bi-directional data line
(slew-rate controlled output, 4 mA)
GND
36
31
-
ground supply
VCC(3.3)
37
32
-
supply voltage (3.0 to 3.6 V); leave this pin
unconnected when using VCC = 5.0 V
AD
38
33
I/O
multiplexed bi-directional address and data
line; represents address A0 or bit 0 of
D[15:0] in conjunction with input ALE;
level-sensitive input or slew-rate controlled
output (4 mA)
TSSOP48
HVQFN48
DATA5
31
DATA4
Address phase: a HIGH-to-LOW transition
on input ALE latches the level on this pin as
address A0 (1 = command, 0 = data)
Data phase: during reading this pin outputs
bit D[0]; during writing the level on this pin is
latched as bit D[0]
A0
39
34
I
address input; selects command (A0 = 1) or
data (A0 = 0); in a multiplexed address/data
bus configuration this pin is not used and
must be tied LOW (connect to GND)
RD
40
35
I
read strobe input
WR
41
36
I
write strobe input
ALE
42
37
I
address latch enable input; a HIGH-to-LOW
transition latches the level on pin AD0 as
address information in a multiplexed
address/data bus configuration; must be
tied LOW (connect to GND) for a separate
address/data bus configuration
CS
43
38
I
chip select input
RESET
44
39
I
reset input (Schmitt trigger); a LOW level
produces an asynchronous reset; connect
to VCC for power-on reset (internal POR
circuit)
CLKOUT
45
40
O
programmable clock output (2 mA)
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
7 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 2:
Symbol[1]
Pin description…continued
Pin
Type
Description
41
-
ground supply
47
42
O
crystal oscillator output (6 MHz); connect a
fundamental parallel-resonant crystal; leave
this pin open when using an external clock
source on pin XTAL1
48
43
I
crystal oscillator input (6 MHz); connect a
fundamental parallel-resonant crystal or an
external clock source (leaving pin XTAL2 is
unconnected)
TSSOP48
HVQFN48
GND
46
XTAL2
XTAL1
[1]
Symbol names with an overscore (e.g. NAME) represent active LOW signals.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
8 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
7. Functional description
The ISP1181 is a full-speed USB interface device with up to 14 configurable
endpoints. It has a fast general-purpose parallel interface for communication with
many types of microcontrollers or microprocessors. It supports different bus
configurations (see Table 3) and local DMA transfers of up to 16 bytes per cycle. The
block diagram is given in Figure 1.
The ISP1181 has 2462 bytes of internal FIFO memory, which is shared among the
enabled USB endpoints. The type and FIFO size of each endpoint can be individually
configured, depending on the required packet size. Isochronous and bulk endpoints
are double-buffered for increased data throughput.
The ISP1181 requires a single supply voltage of 3.3 or 5.0 V and has an internal
3.3 V voltage regulator for powering the analog USB transceiver. It supports
bus-powered operation.
The ISP1181 operates on a 6 MHz oscillator frequency. A programmable clock output
is available up to 48 MHz. During ‘suspend’ state the 115 kHz ±10 % LazyClock
frequency can be output.
7.1 Analog transceiver
The transceiver is compliant with the Universal Serial Bus Specification Rev. 1.1. It
interfaces directly with the USB cable through external termination resistors.
7.2 Philips Serial Interface Engine (SIE)
The Philips SIE implements the full USB protocol layer. It is completely hardwired for
speed and needs no firmware intervention. The functions of this block include:
synchronization pattern recognition, parallel/serial conversion, bit (de-)stuffing, CRC
checking/generation, Packet IDentifier (PID) verification/generation, address
recognition, handshake evaluation/generation.
7.3 Memory Management Unit (MMU) and integrated RAM
The MMU and the integrated RAM provide the conversion between the USB speed
(12 Mbit/s bursts) and the parallel interface to the microcontroller (max. 12 Mbyte/s).
This allows the microcontroller to read and write USB packets at its own speed.
7.4 SoftConnect
The connection to the USB is accomplished by bringing D+ (for high-speed USB
devices) HIGH through a 1.5 kΩ pull-up resistor. In the ISP1181 the 1.5 kΩ pull-up
resistor is integrated on-chip and is not connected to VCC by default. The connection
is established through a command sent by the external/system microcontroller. This
allows the system microcontroller to complete its initialization sequence before
deciding to establish connection with the USB. Re-initialization of the USB connection
can also be performed without disconnecting the cable.
The ISP1181 will check for USB VBUS availability before the connection can be
established. VBUS sensing is provided through pin VBUS.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
9 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Remark: Note that the tolerance of the internal resistors is 25%. This is higher than
the 5% tolerance specified by the USB specification. However, the overall VSE voltage
specification for the connection can still be met with a good margin. The decision to
make use of this feature lies with the USB equipment designer.
7.5 GoodLink
Indication of a good USB connection is provided at pin GL through GoodLink
technology. During enumeration the LED indicator will blink on momentarily. When
the ISP1181 has been successfully enumerated (the device address is set), the LED
indicator will remain permanently on. Upon each successful packet transfer (with
ACK) to and from the ISP1181 the LED will blink off for 100 ms. During ‘suspend’
state the LED will remain off.
This feature provides a user-friendly indicator of the status of the USB device, the
connected hub and the USB traffic. It is a useful field diagnostics tool for isolating
faulty equipment. It can therefore help to reduce field support and hotline overhead.
7.6 Bit clock recovery
The bit clock recovery circuit recovers the clock from the incoming USB data stream
using a 4× over-sampling principle. It is able to track jitter and frequency drift as
specified by the USB Specification Rev. 1.1.
7.7 Voltage regulator
A 5 V to 3.3 V voltage regulator is integrated on-chip to supply the analog transceiver
and internal logic. This voltage is available at pin Vreg(3.3) to supply an external 1.5 kΩ
pull-up resistor on the D+ line. Alternatively, the ISP1181 provides SoftConnect
technology via an integrated 1.5 kΩ pull-up resistor (see Section 7.4).
7.8 PLL clock multiplier
A 6 MHz to 48 MHz clock multiplier Phase-Locked Loop (PLL) is integrated on-chip.
This allows for the use of a low-cost 6 MHz crystal, which also minimizes EMI. No
external components are required for the operation of the PLL.
7.9 Parallel I/O (PIO) and Direct Memory Access (DMA) interface
A generic PIO interface is defined for speed and ease-of-use. It also allows direct
interfacing to most microcontrollers. To a microcontroller, the ISP1181 appears as a
memory device with an 8/16-bit data bus and an 1-bit address bus. The ISP1181
supports both multiplexed and non-multiplexed address and data buses.
The ISP1181 can also be configured as a DMA slave device to allow more efficient
data transfer. One of the 14 endpoint FIFOs may directly transfer data to/from the
local shared memory. The DMA interface can be configured independently from the
PIO interface.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
10 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
8. Modes of operation
The ISP1181 has four bus configuration modes, selected via pins BUS_CONF1 and
BUSCONF0:
Mode 0
16-bit I/O port shared with 16-bit DMA port
Mode 1
reserved
Mode 2
8-bit I/O port shared with 8-bit DMA port
Mode 3
reserved.
The bus configurations for each of these modes are given in Table 3. Typical interface
circuits for each mode are given in Section 20.1.
Table 3:
Bus configuration modes
Mode
BUS_CONF[1:0]
PIO width
DMA width
DMAWD = 0
DMAWD = 1
D[15:0]
Description
0
0
0
D[15:0]
-
multiplexed address/data on pin AD0;
bus is shared by 16-bit I/O port and
16-bit DMA port
1
0
1
reserved
reserved
reserved
reserved
2
1
0
D[7:0]
D[7:0]
-
multiplexed address/data on pin AD0;
bus is shared by 8-bit I/O port and 8-bit
DMA port
3
1
1
reserved
reserved
reserved
reserved
9. Endpoint descriptions
Each USB device is logically composed of several independent endpoints. An
endpoint acts as a terminus of a communication flow between the host and the
device. At design time each endpoint is assigned a unique number (endpoint
identifier, see Table 4). The combination of the device address (given by the host
during enumeration), the endpoint number and the transfer direction allows each
endpoint to be uniquely referenced.
The ISP1181 has 16 endpoints: endpoint 0 (control IN and OUT) plus 14 configurable
endpoints, which can be individually defined as interrupt/bulk/isochronous, IN or OUT.
Each enabled endpoint has an associated FIFO, which can be accessed either via
the parallel I/O interface or via DMA.
9.1 Endpoint access
Table 4 lists the endpoint access modes and programmability. All endpoints support
I/O mode access. Endpoints 1 to 14 also support DMA access. FIFO DMA access is
selected and enabled via bits EPIDX[3:0] and DMAEN of the DMA Configuration
Register. A detailed description of the DMA operation is given in Section 10.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
11 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 4:
Endpoint access and programmability
Endpoint
identifier
FIFO size (bytes)[1]
Double
buffering
I/O mode
access
DMA mode
access
Endpoint type
0
64 (fixed)
no
yes
no
control OUT[2]
0
64 (fixed)
no
yes
no
control IN[2]
1
programmable
supported
supported
supported
programmable
2
programmable
supported
supported
supported
programmable
3
programmable
supported
supported
supported
programmable
4
programmable
supported
supported
supported
programmable
5
programmable
supported
supported
supported
programmable
6
programmable
supported
supported
supported
programmable
7
programmable
supported
supported
supported
programmable
8
programmable
supported
supported
supported
programmable
9
programmable
supported
supported
supported
programmable
10
programmable
supported
supported
supported
programmable
11
programmable
supported
supported
supported
programmable
12
programmable
supported
supported
supported
programmable
13
programmable
supported
supported
supported
programmable
14
programmable
supported
supported
supported
programmable
[1]
[2]
The total amount of FIFO storage allocated to enabled endpoints must not exceed 2462 bytes.
IN: input for the USB host (ISP1181 transmits); OUT: output from the USB host (ISP1181 receives). The data flow direction is
determined by bit EPDIR in the Endpoint Configuration Register.
9.2 Endpoint FIFO size
The size of the FIFO determines the maximum packet size that the hardware can
support for a given endpoint. Only enabled endpoints are allocated space in the
shared FIFO storage, disabled endpoints have zero bytes. Table 5 lists the
programmable FIFO sizes.
The following bits in the Endpoint Configuration Register (ECR) affect FIFO
allocation:
• Endpoint enable bit (FIFOEN)
• Size bits of an enabled endpoint (FFOSZ[3:0])
• Isochronous bit of an enabled endpoint (FFOISO).
Remark: Register changes that affect the allocation of the shared FIFO storage
among endpoints must not be made while valid data is present in any FIFO of the
enabled endpoints. Such changes will render all FIFO contents undefined.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
12 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 5:
Programmable FIFO size
FFOSZ[3:0]
Non-isochronous
Isochronous
0000
8 bytes
16 bytes
0001
16 bytes
32 bytes
0010
32 bytes
48 bytes
0011
64 bytes
64 bytes
0100
reserved
96 bytes
0101
reserved
128 bytes
0110
reserved
160 bytes
0111
reserved
192 bytes
1000
reserved
256 bytes
1001
reserved
320 bytes
1010
reserved
384 bytes
1011
reserved
512 bytes
1100
reserved
640 bytes
1101
reserved
768 bytes
1110
reserved
896 bytes
1111
reserved
1023 bytes
Each programmable FIFO can be configured independently via its ECR, but the total
physical size of all enabled endpoints (IN plus OUT) must not exceed 2462 bytes
(512 bytes for non-isochronous FIFOs).
Table 6 shows an example of a configuration fitting in the maximum available space of
2462 bytes. The total number of logical bytes in the example is 1311. The physical
storage capacity used for double buffering is managed by the device hardware and is
transparent to the user.
Table 6:
Memory configuration example
Physical size
(bytes)
Logical size
(bytes)
Endpoint description
64
64
control IN (64 byte fixed)
64
64
control OUT (64 byte fixed)
2046
1023
double-buffered 1023-byte isochronous endpoint
16
16
16-byte interrupt OUT
16
16
16-byte interrupt IN
128
64
double-buffered 64-byte bulk OUT
128
64
double-buffered 64-byte bulk IN
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
13 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
9.3 Endpoint initialization
In response to the standard USB request Set Interface, the firmware must program all
16 ECRs of the ISP1181 in sequence (see Table 4), whether the endpoints are
enabled or not. The hardware will then automatically allocate FIFO storage space.
If all endpoints have been configured successfully, the firmware must return an empty
packet to the control IN endpoint to acknowledge success to the host. If there are
errors in the endpoint configuration, the firmware must stall the control IN endpoint.
When reset by hardware or via the USB bus, the ISP1181 disables all endpoints and
clears all ECRs, except for the control endpoint which is fixed and always enabled.
Endpoint initialization can be done at any time; however, it is valid only after
enumeration.
9.4 Endpoint I/O mode access
When an endpoint event occurs (a packet is transmitted or received), the associated
endpoint interrupt bits (EPn) of the Interrupt Register (IR) will be set by the SIE. The
firmware then responds to the interrupt and selects the endpoint for processing.
The endpoint interrupt bit will be cleared by reading the Endpoint Status Register
(ESR). The ESR also contains information on the status of the endpoint buffer.
For an OUT (= receive) endpoint, the packet length and packet data can be read from
ISP1181 using the Read Buffer command. When the whole packet has been read,
the firmware sends a Clear Buffer command to enable the reception of new packets.
For an IN (= transmit) endpoint, the packet length and data to be sent can be written
to ISP1181 using the Write Buffer command. When the whole packet has been
written to the buffer, the firmware sends a Validate Buffer command to enable data
transmission to the host.
9.5 Special actions on control endpoints
Control endpoints require special firmware actions. The arrival of a SETUP packet
flushes the IN buffer and disables the Validate Buffer and Clear Buffer commands for
the control IN and OUT endpoints. The microcontroller needs to re-enable these
commands by sending an Acknowledge Setup command to both control endpoints.
This ensures that the last SETUP packet stays in the buffer and that no packets can
be sent back to the host until the microcontroller has explicitly acknowledged that it
has seen the SETUP packet.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
14 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
10. DMA transfer
Direct Memory Access (DMA) is a method to transfer data from one location to
another in a computer system, without intervention of the central processor (CPU).
Many different implementations of DMA exist. The ISP1181 supports two methods:
• 8237 compatible mode: based on the DMA subsystem of the IBM personal
computers (PC, AT and all its successors and clones); this architecture uses the
Intel 8237 DMA controller and has separate address spaces for memory and I/O
• DACK-only mode: based on the DMA implementation in some embedded RISC
processors, which has a single address space for both memory and I/O.
The ISP1181 supports DMA transfer for all 14 configurable endpoints (see Table 4).
Only one endpoint at a time can be selected for DMA transfer. The DMA operation of
the ISP1181 can be interleaved with normal I/O mode access to other endpoints.
The following features are supported:
• Single-cycle or burst transfers (up tot 16 bytes per cycle)
• Programmable transfer direction (read or write)
• Multiple End-Of-Transfer (EOT) sources: external pin, internal conditions,
short/empty packet
• Programmable signal levels on pins DREQ, DACK and EOT.
10.1 Selecting an endpoint for DMA transfer
The target endpoint for DMA access is selected via bits EPDIX[3:0] in the DMA
Configuration Register, as shown in Table 7. The transfer direction (read or write) is
automatically set by bit EPDIR in the associated ECR, to match the selected endpoint
type (OUT endpoint: read; IN endpoint: write).
Asserting input DACK automatically selects the endpoint specified in the DMA
Configuration Register, regardless of the current endpoint used for I/O mode access.
Table 7:
Endpoint selection for DMA transfer
Endpoint
identifier
EPIDX[3:0]
EPDIR = 0
EPDIR = 1
1
0010
OUT: read
IN: write
2
0011
OUT: read
IN: write
3
0100
OUT: read
IN: write
4
0101
OUT: read
IN: write
5
0110
OUT: read
IN: write
6
0111
OUT: read
IN: write
7
1000
OUT: read
IN: write
8
1001
OUT: read
IN: write
9
1010
OUT: read
IN: write
10
1011
OUT: read
IN: write
11
1100
OUT: read
IN: write
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Transfer direction
Rev. 04 — 30 October 2001
15 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 7:
Endpoint selection for DMA transfer…continued
Endpoint
identifier
EPIDX[3:0]
12
Transfer direction
EPDIR = 0
EPDIR = 1
1101
OUT: read
IN: write
13
1110
OUT: read
IN: write
14
1111
OUT: read
IN: write
10.2 8237 compatible mode
The 8237 compatible DMA mode is selected by clearing bit DAKOLY in the Hardware
Configuration Register (see Table 21). The pin functions for this mode are shown in
Table 8.
Table 8:
Symbol
8237 compatible mode: pin functions
Description
I/O
Function
DREQ
DMA request
O
ISP1181 requests a DMA transfer
DACK
DMA acknowledge
I
DMA controller confirms the transfer
EOT
end of transfer
I
DMA controller terminates the transfer
RD
read strobe
I
instructs ISP1181 to put data on the bus
WR
write strobe
I
instructs ISP1181 to get data from the bus
The DMA subsystem of an IBM compatible PC is based on the Intel 8237 DMA
controller. It operates as a ‘fly-by’ DMA controller: the data is not stored in the DMA
controller, but it is transferred between an I/O port and a memory address. A typical
example of ISP1181 in 8237 compatible DMA mode is given in Figure 4.
The 8237 has two control signals for each DMA channel: DRQ (DMA Request) and
DACK (DMA Acknowledge). General control signals are HRQ (Hold Request), HLDA
(Hold Acknowledge) and EOP (End-Of-Process). The bus operation is controlled via
MEMR (Memory Read), MEMW (Memory Write), IOR (I/O read) and IOW (I/O write).
AD,
DATA1 to DATA15
RAM
MEMR
MEMW
DMA
CONTROLLER
8237
ISP1181
CPU
DREQ
DREQ
HRQ
HRQ
DACK
DACK
HLDA
HLDA
RD
IOR
WR
IOW
MGS778
Fig 4. ISP1181 in 8237 compatible DMA mode.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
16 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
The following example shows the steps which occur in a typical DMA transfer:
1. ISP1181 receives a data packet in one of its endpoint FIFOs; the packet must be
transferred to memory address 1234H.
2. ISP1181 asserts the DREQ signal requesting the 8237 for a DMA transfer.
3. The 8237 asks the CPU to release the bus by asserting the HRQ signal.
4. After completing the current instruction cycle, the CPU places the bus control
signals (MEMR, MEMW, IOR and IOW) and the address lines in three-state and
asserts HLDA to inform the 8237 that it has control of the bus.
5. The 8237 now sets its address lines to 1234H and activates the MEMW and IOR
control signals.
6. The 8237 asserts DACK to inform the ISP1181 that it will start a DMA transfer.
7. The ISP1181 now places the byte or word to be transferred on the data bus lines,
because its RD signal was asserted by the 8237.
8. The 8237 waits one DMA clock period and then de-asserts MEMW and IOR. This
latches and stores the byte or word at the desired memory location. It also
informs the ISP1181 that the data on the bus lines has been transferred.
9. The ISP1181 de-asserts the DREQ signal to indicate to the 8237 that DMA is no
longer needed. In Single cycle mode this is done after each byte or word, in
Burst mode following the last transferred byte or word of the DMA cycle.
10. The 8237 de-asserts the DACK output indicating that the ISP1181 must stop
placing data on the bus.
11. The 8237 places the bus control signals (MEMR, MEMW, IOR and IOW) and the
address lines in three-state and de-asserts the HRQ signal, informing the CPU
that it has released the bus.
12. The CPU acknowledges control of the bus by de-asserting HLDA. After activating
the bus control lines (MEMR, MEMW, IOR and IOW) and the address lines, the
CPU resumes the execution of instructions.
For a typical bulk transfer the above process is repeated 64 times, once for each byte.
After each byte the address register in the DMA controller is incremented and the
byte counter is decremented. When using 16-bit DMA the number of transfers is 32
and address incrementing and byte counter decrementing is done by 2 for each word.
10.3 DACK-only mode
The DACK-only DMA mode is selected by setting bit DAKOLY in the Hardware
Configuration Register (see Table 21). The pin functions for this mode are shown in
Table 9. A typical example of ISP1181 in DACK-only DMA mode is given in Figure 5.
Table 9:
DACK-only mode: pin functions
Symbol
Description
I/O
Function
DREQ
DMA request
O
ISP1181 requests a DMA transfer
DACK
DMA acknowledge
I
DMA controller confirms the transfer;
also functions as data strobe
EOT
End-Of-Transfer
I
DMA controller terminates the transfer
RD
read strobe
I
not used
WR
write strobe
I
not used
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
17 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
In DACK-only mode the ISP1181 uses the DACK signal as data strobe. Input signals
RD and WR are ignored. This mode is used in CPU systems that have a single
address space for memory and I/O access. Such systems have no separate MEMW
and MEMR signals: the RD and WR signals are also used as memory data strobes.
ISP1181
DMA
CONTROLLER
DREQ
DREQ
DACK
DACK
AD,
DATA1 to DATA15
RAM
CPU
HRQ
HRQ
HLDA
HLDA
RD
WR
MGS779
Fig 5. ISP1181 in DACK-only DMA mode.
10.4 End-Of-Transfer conditions
10.4.1
Bulk endpoints
A DMA transfer to/from a bulk endpoint can be terminated by any of the following
conditions (bit names refer to the DMA Configuration Register, see Table 25):
•
•
•
•
An external End-Of-Transfer signal occurs on input EOT
The internal DMA Counter Register reaches zero (CNTREN = 1)
A short/empty packet is received on an enabled OUT endpoint (SHORTP = 1)
DMA operation is disabled by clearing bit DMAEN.
External EOT: When reading from an OUT endpoint, an external EOT will stop the
DMA operation and clear any remaining data in the current FIFO. For a doublebuffered endpoint the other (inactive) buffer is not affected.
When writing to an IN endpoint, an EOT will stop the DMA operation and the data
packet in the FIFO (even if it is smaller than the maximum packet size) will be sent to
the USB host at the next IN token.
DMA Counter Register zero: An EOT from the DMA Counter Register is enabled by
setting bit CNTREN in the DMA Configuration Register. The ISP1181 has a 16-bit
DMA Counter Register, which specifies the number of bytes to be transferred. When
DMA is enabled (DMAEN = 1), the internal DMA counter is loaded with the value from
the DMA Counter Register. When the internal counter reaches zero an EOT condition
is generated and the DMA operation stops.
Short/empty packet: Normally, the transfer byte count must be set via a control
endpoint before any DMA transfer takes place. When a short/empty packet has been
enabled as EOT indicator (SHORTP = 1), the transfer size is determined by the
presence of a short/empty packet in the data. This mechanism permits the use of a
fully autonomous data transfer protocol.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
18 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
When reading from an OUT endpoint, reception of a short/empty packet at an OUT
token will stop the DMA operation after transferring the data bytes of this packet.
When writing to an IN endpoint, a short packet transferred at an IN token will stop the
DMA operation after all bytes have been transferred. If the number of bytes in the
buffer is zero, ISP1181 will automatically send an empty packet.
Table 10:
Summary of EOT conditions for a bulk endpoint
EOT condition
OUT endpoint
IN endpoint
EOT input
EOT is active
EOT is active
DMA Counter Register
counter reaches zero
counter reaches zero
Short packet
short packet is received and
transferred
counter reaches zero in the
middle of the buffer
Empty packet
empty packet is received and
transferred
empty packet is automatically
appended when needed[1]
DMAEN bit in DMA
Configuration Register
DMAEN = 0
DMAEN = 0
[1]
10.4.2
If short/empty packet EOT is enabled (SHORTP = 1 in DMA Configuration Register) and DMA
Counter Register is zero.
Isochronous endpoints
A DMA transfer to/from an isochronous endpoint can be terminated by any of the
following conditions (bit names refer to the DMA Configuration Register, see
Table 25):
•
•
•
•
An external End-Of-Transfer signal occurs on input EOT
The internal DMA Counter Register reaches zero (CNTREN = 1)
An End-Of-Packet (EOP) signal is detected
DMA operation is disabled by clearing bit DMAEN.
Table 11:
Recommended EOT usage for isochronous endpoints
EOT condition
OUT endpoint
IN endpoint
EOT input active
do not use
preferred
DMA Counter Register zero
do not use
preferred
End-Of-Packet
preferred
do not use
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
19 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
11. Suspend and resume
11.1 Suspend conditions
The ISP1181 detects a USB ‘suspend’ status in the following cases:
• A J-state is present on the USB bus for 3 ms
• VBUS is lost (weak pull-up/down on D+ and D−)
• SoftConnect is disabled by clearing bit SOFTCT in the Mode Register, with
external pull-ups disabled by EXTPUL = 0 in the Hardware Configuration Register.
In this situation ISP1181 is effectively disconnected from the USB bus.
ISP1181 will remain in ‘suspend’ state for at least 5 ms, before responding to external
wake-up events such as global resume, bus traffic, wake-up on CS or WAKEUP. The
typical timing is shown in Figure 6.
GOSUSP
suspend
>5 ms
start detection of
wake-up conditions
WAKEUP
MGS949
Fig 6. Typical suspend timing.
Bus-powered devices that are suspended must not consume more than 500 µA of
current. This is achieved by shutting down the power to system components or
supplying them with a reduced voltage.
ISP1181 is always in powered-off mode during ‘suspend’ state. Default, bit PWROFF
in the Hardware Configuration register is logic 1 and this value should not be changed
under any condition. This powered-off mode is explained in detail in Section 11.1.1.
The steps leading up to ‘suspend’ status are as follows:
1. Upon detection of a ‘wake-up’ to ‘suspend’ transition ISP1181 sets bit SUSPND
in the Interrupt Register. This will generate an interrupt if bit IESUSP in the
Interrupt Enable Register is set.
2. When the firmware detects a ‘suspend’ condition it must prepare all system
components for ‘suspend’ state:
a. All signals connected to ISP1181 must enter appropriate states to meet the
power consumption requirements of ‘suspend’ state.
b. All input pins of ISP1181 must have a CMOS logic 0 or logic 1 level.
3. In the interrupt service routine the firmware must check the current status of the
USB bus. When bit BUSTATUS in the Interrupt Register is logic 0, the USB bus
has left ‘suspend’ mode and the process must be aborted. Otherwise, the next
step can be executed.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
20 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
4. To meet the ‘suspend’ current requirements for a bus-powered device, the
internal clocks must be switched off by clearing bit CLKRUN in the Hardware
Configuration Register.
5. When the firmware has set and cleared the GOSUSP bit in the Mode Register,
the ISP1181 enters ‘suspend’ state. In powered-off application, the ISP1181
asserts output SUSPEND and switches off the internal clocks after 2 ms.
11.1.1
Powered-off application
In powered-off application (PWROFF = 1 in the Hardware Configuration Register) the
supply of the CPU and other parts of the circuit is removed during ‘suspend’ state.
The SUSPEND output is active HIGH during ‘suspend’ state, making it suitable as a
power switch control signal, e.g. for an external oscillator.
Input pins of ISP1181 are pulled to ground via the pin buffers. Outputs are made
three-state to prevent current flowing in the application. Bi-directional pins are made
three-state and must be pulled to ground externally by the application. The power
supply of external pull-ups must also be removed to reduce power consumption.
GOSUSP
WAKEUP
2 ms
0.5 ms
SUSPEND
MGS782
Fig 7. Suspend and resume timing for powered-off application.
Table 12:
Pin states in powered-off application
Pin
Type
Appropriate state
A0
I
inactive
DATA[15:0]
I/O (three-state)
SUSPEND
O
ISP1181 drives logic 1
WAKEUP
I
inactive
INT
O
powered off; internally connected to ground (logic 0)
RESET
I
externally driven[1] to logic 1
CS
I
powered off; internally connected to ground (logic 0)
RD
I
powered off; internally connected to ground (logic 0)
WR
I
powered off; internally connected to ground (logic 0)
XTAL1
I
powered off; internally connected to ground (logic 0)
CLKOUT
O
ISP1181 drives logic 0, if the NOLAZY bit is set to
logic 1 in the Hardware Configuration Register
[1]
‘Externally driven’ refers to logic outside the ISP1181.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
21 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
When external components are powered-off, it is possible that interface signals RD,
WR and CS have unknown values immediately after leaving ‘suspend’ state. To
prevent corruption of its internal registers, ISP1181 enables a locking mechanism
once suspend is enabled.
After wake-up from suspend’ state, all internal registers except the Unlock Register
are write-protected. A special unlock operation is needed to re-enable write access.
This prevents data corruption during power-up of external components.
Figure 8 shows a typical bus-powered modem application using ISP1181 in
powered-off mode. The SUSPEND output is used to switch off power to the
microcontroller and other external circuits during ‘suspend’ state. The ISP1181 is
woken up via the USB bus (global resume) or by the ring detection circuit on the
telephone line.
VBUS
USB
VCC
D+
D−
VCC
power
switch
MICROCONTROLLER
ISP1181
SUSPEND
WAKEUP
RING DETECTION
LINE
MGS783
Fig 8. SUSPEND and WAKEUP signals in a powered-off modem application.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
22 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
11.2 Resume conditions
Wake-up from ‘suspend’ state is initiated either by the USB host or by the application:
• USB host: drives a K-state on the USB bus (global resume)
• Application: remote wake-up via a HIGH level on input WAKEUP or a LOW level
on input CS (if enabled via bit WKUPCS in the Hardware Configuration Register).
The steps of a wake-up sequence are as follows:
1. The internal oscillator and the PLL multiplier are re-enabled. When stabilized, the
clock signals are routed to all internal circuits of the ISP1181.
2. The SUSPEND output is de-asserted and the RESUME bit in the Interrupt
Register is set. This will generate an interrupt if bit IERESUME in the Interrupt
Enable Register is set.
3. Maximum 15 ms after starting the wake-up sequence the ISP1181 resumes its
normal functionality.
4. In case of a remote wake-up ISP1181 drives a K-state on the USB bus for 10 ms.
5. Following the de-assertion of output SUSPEND, the application restores itself
and other system components to normal operating mode.
6. After wake-up the internal registers of ISP1181 are write-protected to prevent
corruption by inadvertent writing during power-up of external components. The
firmware must send an Unlock Device command to the ISP1181 to restore its full
functionality. See Section 12.3.2 for more details.
11.3 Control bits in suspend and resume
Table 13:
Summary of control bits
Register
Bit
Function
Interrupt
SUSPND
a transition from ‘awake’ to ‘suspend’ state was
detected
BUSTATUS
monitors USB bus status (logic 1 = suspend);
used when interrupt is serviced
Interrupt Enable
IESUSP
enables output INT to signal ‘suspend’ state
Mode
SOFTCT
enables SoftConnect pull-up resistor to USB bus
GOSUSP
a HIGH-to-LOW transition enables ‘suspend’
state
EXTPUL
selects internal (SoftConnect) or external pull-up
resistor
WKUPCS
enables wake-up on LOW level of input CS
PWROFF
selects powered-off mode during ‘suspend’ state
all
sending data AA37H unlocks the internal
registers for writing after a ‘resume’
Hardware
Configuration
Unlock
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
23 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
12. Commands and registers
The functions and registers of ISP1181 are accessed via commands, which consist
of a command code followed by optional data bytes (read or write action). An
overview of the available commands and registers is given in Table 14.
A complete access consists of two phases:
1. Command phase: when address bit A0 = 1, the ISP1181 interprets the data on
the lower byte of the bus (bits D7 to D0) as a command code. Commands without
a data phase are executed immediately.
2. Data phase (optional): when address bit A0 = 0, the ISP1181 transfers the data
on the bus to or from a register or endpoint FIFO. Multi-byte registers are
accessed least significant byte/word first.
The following applies for register or FIFO access in 16-bit bus mode:
• The upper byte (bits D15 to D8) in command phase or the undefined byte in data
phase are ignored.
• The access of registers is word-aligned: byte access is not allowed.
• If the packet length is odd, the upper byte of the last word in an IN endpoint buffer
is not transmitted to the host. When reading from an OUT endpoint buffer, the
upper byte of the last word must be ignored by the firmware. The packet length is
stored in the first 2 bytes of the endpoint buffer.
Table 14:
Command and register summary
Destination
Code (Hex)
Transaction[1]
Write Control OUT Configuration
Endpoint Configuration Register
endpoint 0 OUT
20
write 1 byte[2]
Write Control IN Configuration
Endpoint Configuration Register
endpoint 0 IN
21
write 1 byte[2]
Write Endpoint n Configuration
(n = 1 to 14)
Endpoint Configuration Register
endpoint 1 to 14
22 to 2F
write 1 byte[2][3]
Read Control OUT Configuration
Endpoint Configuration Register
endpoint 0 OUT
30
read 1 byte[2]
Read Control IN Configuration
Endpoint Configuration Register
endpoint 0 IN
31
read 1 byte[2]
Read Endpoint n Configuration
(n = 1 to 14)
Endpoint Configuration Register
endpoint 1 to 14
32 to 3F
read 1 byte[2]
Write/Read Device Address
Address Register
B6/B7
write/read 1 byte[2]
Write/Read Mode Register
Mode Register
B8/B9
write/read 1 byte[2]
Write/Read Hardware Configuration Hardware Configuration Register
BA/BB
write/read 2 bytes
Write/Read Interrupt Enable
Register
Interrupt Enable Register
C2/C3
write/read 4 bytes
Write/Read DMA Configuration
DMA Configuration Register
F0/F1
write/read 2 bytes
Write/Read DMA Counter
DMA Counter Register
F2/F3
write/read 2 bytes
Reset Device
resets all registers
F6
-
Name
Initialization commands
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
24 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 14:
Command and register summary…continued
Destination
Code (Hex)
Transaction[1]
Write Control OUT Buffer
illegal: endpoint is read-only
(00)
-
Write Control IN Buffer
FIFO endpoint 0 IN
01
N ≤ 64 bytes
Write Endpoint n Buffer
(n = 1 to 14)
FIFO endpoint 1 to 14
(IN endpoints only)
02 to 0F
isochronous: N ≤ 1023 bytes
Read Control OUT Buffer
FIFO endpoint 0 OUT
10
N ≤ 64 bytes
Read Control IN Buffer
illegal: endpoint is write-only
(11)
-
Read Endpoint n Buffer
(n = 1 to 14)
FIFO endpoint 1 to 14
(OUT endpoints only)
12 to 1F
isochronous:
N ≤ 1023 bytes[4]
Name
Data flow commands
interrupt/bulk: N ≤ 64 bytes
interrupt/bulk: N ≤ 64 bytes
Stall Control OUT Endpoint
Endpoint 0 OUT
40
-
Stall Control IN Endpoint
Endpoint 0 IN
41
-
Stall Endpoint
n (n = 1 to 14)
Endpoint 1 to 14
42 to 4F
-
Read Control OUT Status
Endpoint Status Register
endpoint 0 OUT
50
read 1 byte[2]
Read Control IN Status
Endpoint Status Register
endpoint 0 IN
51
read 1 byte[2]
Read Endpoint n Status
(n = 1 to 14)
Endpoint Status Register n
endpoint 1 to 14
52 to 5F
read 1 byte[2]
Validate Control OUT Buffer
illegal: IN endpoints only[5]
(60)
-
61
-[3]
IN[5]
Validate Control IN Buffer
FIFO endpoint 0
Validate Endpoint n Buffer
(n = 1 to 14)
FIFO endpoint 1 to 14
(IN endpoints only)[5]
62 to 6F
-[3]
Clear Control OUT Buffer
FIFO endpoint 0 OUT
70
-[3]
Clear Control IN Buffer
illegal[6]
(71)
-
Clear Endpoint n Buffer
(n = 1 to 14)
FIFO endpoint 1 to 14
(OUT endpoints only)[6]
72 to 7F
[3]
Unstall Control OUT Endpoint
Endpoint 0 OUT
80
-
Unstall Control IN Endpoint
Endpoint 0 IN
81
-
Unstall Endpoint n
(n = 1 to 14)
Endpoint 1 to 14
82 to 8F
-
Check Control OUT Status[7]
Endpoint Status Image Register
endpoint 0 OUT
D0
read 1 byte[2]
Check Control IN Status[7]
Endpoint Status Image Register
endpoint 0 IN
D1
read 1 byte[2]
Check Endpoint n Status
(n = 1 to 14)[7]
Endpoint Status Image Register n
endpoint 1 to 14
D2 to DF
read 1 byte[2]
Acknowledge Setup
Endpoint 0 IN and OUT
F4
-[3]
Read Control OUT Error Code
Error Code Register
endpoint 0 OUT
A0
read 1 byte[2]
Read Control IN Error Code
Error Code Register
endpoint 0 IN
A1
read 1 byte[2]
General commands
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
25 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 14:
Command and register summary…continued
Name
Destination
Code (Hex)
Transaction[1]
Read Endpoint n Error Code
(n = 1 to 14)
Error Code Register
endpoint 1 to 14
A2 to AF
read 1 byte[2]
Unlock Device
all registers with write access
B0
write 2 bytes
Write/Read Scratch Register
Scratch Register
B2/B3
write/read 2 bytes
Read Frame Number
Frame Number Register
B4
read 1 or 2 bytes
Read Chip ID
Chip ID Register
B5
read 2 bytes
Read Interrupt Register
Interrupt Register
C0
read 4 bytes
[1]
[2]
[3]
[4]
[5]
[6]
[7]
With N representing the number of bytes, the number of words for 16-bit bus width is: (N + 1) DIV 2.
When accessing an 8-bit register in 16-bit mode, the upper byte is invalid.
In 8-bit bus mode this command requires more time to complete than other commands. See Table 59.
During isochronous transfer in 16-bit mode, because N ≤ 1023, the firmware must take care of the upper byte.
Validating an OUT endpoint buffer causes unpredictable behavior of ISP1181.
Clearing an IN endpoint buffer causes unpredictable behavior of ISP1181.
Reads a copy of the Status Register: executing this command does not clear any status bits or interrupt bits.
12.1 Initialization commands
Initialization commands are used during the enumeration process of the USB
network. These commands are used to configure and enable the embedded
endpoints. They also serve to set the USB assigned address of ISP1181 and to
perform a device reset.
12.1.1
Write/Read Endpoint Configuration
This command is used to access the Endpoint Configuration Register (ECR) of the
target endpoint. It defines the endpoint type (isochronous or bulk/interrupt), direction
(OUT/IN), FIFO size and buffering scheme. It also enables the endpoint FIFO. The
register bit allocation is shown in Table 15. A bus reset will disable all endpoints.
The allocation of FIFO memory only takes place after all 16 endpoints have been
configured in sequence (from endpoint 0 OUT to endpoint 14). Although the control
endpoints have fixed configurations, they must be included in the initialization
sequence and be configured with their default values (see Table 4). Automatic FIFO
allocation starts when endpoint 14 has been configured.
Remark: If any change is made to an endpoint configuration which affects the
allocated memory (size, enable/disable), the FIFO memory contents of all endpoints
becomes invalid. Therefore, all valid data must be removed from enabled endpoints
before changing the configuration.
Code (Hex): 20 to 2F — write (control OUT, control IN, endpoint 1 to 14)
Code (Hex): 30 to 3F — read (control OUT, control IN, endpoint 1 to 14)
Transaction — write/read 1 byte
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
26 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 15:
Endpoint Configuration Register: bit allocation
Bit
Symbol
Reset
Access
7
6
5
4
FIFOEN
EPDIR
DBLBUF
FFOISO
3
2
1
0
FFOSZ[3:0]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Table 16:
12.1.2
Endpoint Configuration Register: bit description
Bit
Symbol
Description
7
FIFOEN
A logic 1 indicates an enabled FIFO with allocated memory.
A logic 0 indicates a disabled FIFO (no bytes allocated).
6
EPDIR
This bit defines the endpoint direction (0 = OUT, 1 = IN); it also
determines the DMA transfer direction (0 = read, 1 = write)
5
DBLBUF
A logic 1 indicates that this endpoint has double buffering.
4
FFOISO
A logic 1 indicates an isochronous endpoint. A logic 0 indicates
a bulk or interrupt endpoint.
3 to 0
FFOSZ[3:0]
Selects the FIFO size according to Table 5
Write/Read Device Address
This command is used to set the USB assigned address in the Address Register and
enable the USB device. The Address Register bit allocation is shown in Table 17.
A USB bus reset sets the device address to 00H (internally) and enables the device.
The value of the Address Register (accessible by the micro) is not altered by the bus
reset. In response to the standard USB request Set Address the firmware must issue
a Write Device Address command, followed by sending an empty packet to the host.
The new device address is activated when the host acknowledges the empty packet.
Code (Hex): B6/B7 — write/read Address Register
Transaction — write/read 1 byte
Table 17:
Address Register: bit allocation
Bit
Symbol
Reset
Access
7
6
5
4
DEVEN
3
2
1
0
DEVADR[6:0]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Table 18:
12.1.3
Address Register: bit description
Bit
Symbol
Description
7
DEVEN
A logic 1 enables the device.
6 to 0
DEVADR[6:0]
This field specifies the USB device address.
Write/Read Mode Register
This command is used to access the ISP1181 Mode Register, which consists of
1 byte (bit allocation: see Table 18). In 16-bit bus mode the upper byte is ignored.
The Mode Register controls the DMA bus width, resume and suspend modes,
interrupt activity and SoftConnect operation. It can be used to enable debug mode,
where all errors and Not Acknowledge (NAK) conditions will generate an interrupt.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
27 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Code (Hex): B8/B9 — write/read Mode Register
Transaction — write/read 1 byte
Table 19:
Mode Register: bit allocation
Bit
Symbol
7
6
5
4
3
2
1
0
DMAWD
reserved
GOSUSP
reserved
INTENA
DBGMOD
reserved
SOFTCT
0[1]
0[1]
0[1]
R/W
R/W
R/W
Reset
0[1]
0
0
0
0[1]
Access
R/W
R/W
R/W
R/W
R/W
[1]
Unchanged by a bus reset.
Table 20:
12.1.4
Mode Register: bit description
Bit
Symbol
Description
7
DMAWD
A logic 1 selects 16-bit DMA bus width (bus configuration modes
0 and 2). A logic 0 selects 8-bit DMA bus width. Bus reset value:
unchanged.
6
-
reserved
5
GOSUSP
Writing a logic 1 followed by a logic 0 will activate ‘suspend’
mode.
4
-
reserved
3
INTENA
A logic 1 enables all interrupts. Bus reset value: unchanged.
2
DBGMOD
A logic 1 enables debug mode. where all NAKs and errors will
generate an interrupt. A logic 0 selects normal operation, where
interrupts are generated on every ACK (bulk endpoints) or after
every data transfer (isochronous endpoints). Bus reset value:
unchanged.
1
-
reserved
0
SOFTCT
A logic 1 enables SoftConnect (see Section 7.4). This bit is
ignored if EXTPUL = 1 in the Hardware Configuration Register
(see Table 21). Bus reset value: unchanged.
Write/Read Hardware Configuration
This command is used to access the Hardware Configuration Register, which
consists of 2 bytes. The first (lower) byte contains the device configuration and
control values, the second (upper) byte holds the clock control bits and the clock
division factor. The bit allocation is given in Table 21. A bus reset will not change any
of the programmed bit values.
The Hardware Configuration Register controls the connection to the USB bus, clock
activity and power supply during ‘suspend’ state, output clock frequency, DMA
operating mode and pin configurations (polarity, signalling mode).
Code (Hex): BA/BB — write/read Hardware Configuration Register
Transaction — write/read 2 bytes
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
28 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 21:
Hardware Configuration Register: bit allocation
Bit
Symbol
Reset
Access
Bit
Symbol
Reset
Access
15
14
13
12
reserved
EXTPUL
NOLAZY
CLKRUN
11
9
8
CKDIV[3:0]
0
0
1
0
0
0
1
1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
DAKOLY
DRQPOL
DAKPOL
EOTPOL
WKUPCS
PWROFF
INTLVL
INTPOL
0
1
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Table 22:
Hardware Configuration Register: bit description
Bit
Symbol
Description
15
-
reserved
14
EXTPUL
A logic 1 indicates that an external 1.5 kΩ pull-up resistor is
used on pin D+ and that SoftConnect is not used. Bus reset
value: unchanged.
13
NOLAZY
A logic 1 disables output on pin CLKOUT of the LazyClock
frequency (115 kHz ±10 %) during ‘suspend’ state. A logic 0
causes pin CLKOUT to switch to LazyClock output after
approximately 2 ms delay, following the setting of bit GOSUSP
in the Mode Register. Bus reset value: unchanged.
12
CLKRUN
A logic 1 indicates that the internal clocks are always running,
even during ‘suspend’ state. A logic 0 switches off the internal
oscillator and PLL, when they are not needed. During ‘suspend’
state this bit must be made logic 0 to meet the suspend current
requirements. The clock is stopped after a delay of
approximately 2 ms, following the setting of bit GOSUSP in the
Mode Register. Bus reset value: unchanged.
11 to 8
CKDIV[3:0]
This field specifies the clock division factor N, which controls the
clock frequency on output CLKOUT. The output frequency in
MHz is given by 48/(N + 1). The clock frequency range is
3 to 48 MHz (N = 0 to 15). with a reset value of 12 MHz (N = 3).
The hardware design guarantees no glitches during frequency
change. Bus reset value: unchanged.
7
DAKOLY
A logic 1 selects DACK-only DMA mode. A logic 0 selects 8237
compatible DMA mode. Bus reset value: unchanged.
6
DRQPOL
Selects DREQ signal polarity (0 = active LOW, 1 = active
HIGH). Bus reset value: unchanged.
5
DAKPOL
Selects DACK signal polarity (0 = active LOW, 1 = active HIGH).
Bus reset value: unchanged.
4
EOTPOL
Selects EOT signal polarity (0 = active LOW, 1 = active HIGH).
Bus reset value: unchanged.
3
WKUPCS
A logic 1 enables remote wake-up via a LOW level on input CS.
Bus reset value: unchanged.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
10
Rev. 04 — 30 October 2001
29 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 22:
12.1.5
Hardware Configuration Register: bit description…continued
Bit
Symbol
Description
2
PWROFF
A logic 1 enables powering-off during ‘suspend’ state. Output
SUSPEND is configured as a power switch control signal for
external devices (HIGH during ‘suspend’). This value should
always be initialized to logic 1. Bus reset value: unchanged.
1
INTLVL
Selects the interrupt signalling mode on output INT (0 = level,
1 = pulsed). In pulsed mode an interrupt produces an 166 ns
pulse. See Section 13 for details. Bus reset value: unchanged.
0
INTPOL
Selects INT signal polarity (0 = active LOW, 1 = active HIGH).
Bus reset value: unchanged.
Write/Read Interrupt Enable Register
This command is used to individually enable/disable interrupts from all endpoints, as
well as interrupts caused by events on the USB bus (SOF, SOF lost, EOT, suspend,
resume, reset). A bus reset will not change any of the programmed bit values.
The command accesses the Interrupt Enable Register, which consists of 4 bytes. The
bit allocation is given in Table 23.
Code (Hex): C2/C3 — write/read Interrupt Enable Register
Transaction — write/read 4 bytes
Table 23:
Interrupt Enable Register: bit allocation
Bit
31
30
29
28
Symbol
Reset
Access
Bit
Symbol
Reset
Access
Bit
Symbol
Reset
Access
Bit
Symbol
Reset
Access
27
26
25
24
reserved
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
23
22
21
20
19
18
17
16
IEP14
IEP13
IEP12
IEP11
IEP10
IEP9
IEP8
IEP7
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
15
14
13
12
11
10
9
8
IEP6
IEP5
IEP4
IEP3
IEP2
IEP1
IEP0IN
IEP0OUT
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
reserved
reserved
IEPSOF
IESOF
IEEOT
IESUSP
IERESM
IERST
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Table 24:
Interrupt Enable Register: bit description
Bit
Symbol
Description
31 to 24
-
reserved; must write logic 0
23 to 10
IEP14 to IEP1 A logic 1 enables interrupts from the indicated endpoint.
9
IEP0IN
A logic 1 enables interrupts from the control IN endpoint.
8
IEP0OUT
A logic 1 enables interrupts from the control OUT endpoint.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
30 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 24:
12.1.6
Interrupt Enable Register: bit description…continued
Bit
Symbol
Description
7, 6
-
reserved
5
IEPSOF
A logic 1 enables 1 ms interrupts upon detection of Pseudo
SOF.
4
IESOF
A logic 1 enables interrupt upon SOF detection.
3
IEEOT
A logic 1 enables interrupt upon EOT detection.
2
IESUSP
A logic 1 enables interrupt upon detection of ‘suspend’ state.
1
IERESM
A logic 1 enables interrupt upon detection of a ‘resume’ state.
0
IERST
A logic 1 enables interrupt upon detection of a bus reset.
Write/Read DMA Configuration
This command defines the DMA configuration of ISP1181 and enables/disables DMA
transfers. The command accesses the DMA Configuration Register, which consists of
2 bytes. The bit allocation is given in Table 25. A bus reset will clear bit DMAEN (DMA
disabled), all other bits remain unchanged.
Code (Hex): F0/F1 — write/read DMA Configuration
Transaction — write/read 2 bytes
Table 25:
DMA Configuration Register: bit allocation
Bit
Symbol
15
14
13
12
11
10
9
8
CNTREN
SHORTP
reserved
reserved
reserved
reserved
reserved
reserved
Reset
0[1]
0[1]
0[1]
0[1]
0[1]
0[1]
0[1]
0[1]
Access
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
DMAEN
reserved
Reset
0[1]
0[1]
0[1]
0[1]
0
0
0[1]
0[1]
Access
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Bit
Symbol
[1]
EPDIX[3:0]
BURSTL[1:0]
Unchanged by a bus reset.
Table 26:
DMA Configuration Register: bit description
Bit
Symbol
Description
15
CNTREN
A logic 1 enables the generation of an EOT condition, when the
DMA Counter Register reaches zero. Bus reset value:
unchanged.
14
SHORTP
A logic 1 enables short/empty packet mode. When receiving
(OUT endpoint) a short/empty packet an EOT condition is
generated. When transmitting (IN endpoint) this bit should be
cleared. Bus reset value: unchanged.
13 to 8
-
reserved
7 to 4
EPDIX[3:0]
Indicates the destination endpoint for DMA, see Table 7.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
31 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 26:
DMA Configuration Register: bit description…continued
Bit
Symbol
Description
3
DMAEN
Writing a logic 1 enables DMA transfer, a logic 0 forces the end
of an ongoing DMA transfer and generates an EOT interrupt.
Reading this bit indicates whether DMA is enabled (0 = DMA
stopped, 1 = DMA enabled). This bit is cleared by a bus reset.
2
-
reserved
1 to 0
BURSTL[1:0]
Selects the DMA burst length:
00 — single-cycle mode (1 byte)
01 — burst mode (4 bytes)
10 — burst mode (8 bytes)
11 — burst mode (16 bytes).
Bus reset value: unchanged.
12.1.7
Write/Read DMA Counter
This command accesses the DMA Counter Register, which consists of 2 bytes. The
bit allocation is given in Table 27. Writing to the register sets the number of bytes for a
DMA transfer. Reading the register returns the number of remaining bytes in the
current transfer. A bus reset will not change the programmed bit values.
The internal DMA counter is automatically reloaded from the DMA Counter Register
when DMA is re-enabled (DMAEN = 1). See Section 12.1.6 for more details.
Code (Hex): F2/F3 — write/read DMA Counter Register
Transaction — write/read 2 bytes
Table 27:
DMA Counter Register: bit allocation
Bit
15
14
13
Symbol
Reset
Access
Bit
Access
11
9
8
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
DMACRL[7:0]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Table 28:
DMA Counter Register: bit description
Bit
Symbol
Description
15 to 8
DMACRH[7:0] DMA Counter Register (high byte)
7 to 0
DMACRL[7:0]
DMA Counter Register (low byte)
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
10
DMACRH[7:0]
Symbol
Reset
12
Rev. 04 — 30 October 2001
32 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
12.1.8
Reset Device
This command resets the ISP1181 in the same way as an external hardware reset via
input RESET. All registers are initialized to their ‘reset’ values.
Code (Hex): F6 — reset the device
Transaction — none
12.2 Data flow commands
Data flow commands are used to manage the data transmission between the USB
endpoints and the system microcontroller. Much of the data flow is initiated via an
interrupt to the microcontroller. The data flow commands are used to access the
endpoints and determine whether the endpoint FIFOs contain valid data.
Remark: The IN buffer of an endpoint contains input data for the host, the OUT buffer
receives output data from the host.
12.2.1
Write/Read Endpoint Buffer
This command is used to access endpoint FIFO buffers for reading or writing. First,
the buffer pointer is reset to the beginning of the buffer. Following the command, a
maximum of (N + 2) bytes can be written or read, N representing the size of the
endpoint buffer. For 16-bit access the maximum number of words is (M + 1), with M
given by (N + 1) DIV 2. After each read/write action the buffer pointer is automatically
incremented by 1 (8-bit bus width) or by 2 (16-bit bus width).
In DMA access the first 2 bytes or the first word (the packet length) are skipped:
transfers start at the third byte or the second word of the endpoint buffer. When
reading, the ISP1181 can detect the last byte/word via the EOP condition. When
writing to a bulk/interrupt endpoint, the endpoint buffer must be completely filled
before sending the data to the host. Exception: when a DMA transfer is stopped by an
external EOT condition, the current buffer content (full or not) is sent to the host.
Remark: Reading data after a Write Endpoint Buffer command or writing data after a
Read Endpoint Buffer command data will cause unpredictable behavior of ISP1181.
Code (Hex): 01 to 0F — write (control IN, endpoint 1 to 14)
Code (Hex): 10, 12 to 1F — read (control OUT, endpoint 1 to 14)
Transaction — write/read maximum N + 2 bytes (isochronous endpoint: N ≤ 1023,
bulk/interrupt endpoint: N ≤ 32)
The data in the endpoint FIFO must be organized as shown in Table 29. Examples of
endpoint FIFO access are given in Table 30 (8-bit bus) and Table 31 (16-bit bus).
Table 29:
Endpoint FIFO organization
Byte #
(8-bit bus)
Word #
(16-bit bus)
Description
0
0 (lower byte)
packet length (lower byte)
1
0 (upper byte)
packet length (upper byte)
2
1 (lower byte)
data byte 1
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
33 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 29:
Endpoint FIFO organization…continued
Byte #
(8-bit bus)
Word #
(16-bit bus)
Description
3
1 (upper byte)
data byte 2
…
…
…
(N + 1)
M = (N + 1) DIV 2
data byte N
Table 30:
Example of endpoint FIFO access (8-bit bus width)
A0
Phase
Bus lines
Byte #
Description
1
command
D[7:0]
-
command code (00H to 1FH)
0
data
D[7:0]
0
packet length (lower byte)
0
data
D[7:0]
1
packet length (upper byte)
0
data
D[7:0]
2
data byte 1
0
data
D[7:0]
3
data byte 2
0
data
D[7:0]
4
data byte 3
0
data
D[7:0]
5
data byte 4
…
…
…
…
…
Table 31:
Example of endpoint FIFO access (16-bit bus width)
A0
Phase
Bus lines
Word #
Description
1
command
D[7:0]
-
command code (00H to 1FH)
D[15:8]
-
ignored
0
data
D[15:0]
0
packet length
0
data
D[15:0]
1
data word 1 (data byte 2, data byte 1)
0
data
D[15:0]
2
data word 2 (data byte 4, data byte 3)
…
…
…
…
…
Remark: There is no protection against writing or reading past a buffer’s boundary,
against writing into an OUT buffer or reading from an IN buffer. Any of these actions
could cause an incorrect operation. Data residing in an OUT buffer are only
meaningful after a successful transaction. Exception: during DMA access of a
double-buffered endpoint, the buffer pointer automatically points to the secondary
buffer after reaching the end of the primary buffer.
12.2.2
Read Endpoint Status
This command is used to read the status of an endpoint FIFO. The command
accesses the Endpoint Status Register, the bit allocation of which is shown in
Table 32. Reading the Endpoint Status Register will clear the interrupt bit set for the
corresponding endpoint in the Interrupt Register (see Table 48).
All bits of the Endpoint Status Register are read-only. Bit EPSTAL is controlled by the
Stall/Unstall commands and by the reception of a SETUP token (see Section 12.2.3).
Code (Hex): 50 to 5F — read (control OUT, control IN, endpoint 1 to 14)
Transaction — read 1 byte
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
34 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 32:
Endpoint Status Register: bit allocation
Bit
Symbol
7
6
5
4
3
2
1
0
EPSTAL
EPFULL1
EPFULL0
DATA_PID
OVER
WRITE
SETUPT
CPUBUF
reserved
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
Table 33:
Endpoint Status Register: bit description
Bit
Symbol
Description
7
EPSTAL
This bit indicates whether the endpoint is stalled or not
(1 = stalled, 0 = not stalled).
Set to logic 1 by a Stall Endpoint command, cleared to logic 0 by
an Unstall Endpoint command. The endpoint is automatically
unstalled upon reception of a SETUP token.
6
EPFULL1
A logic 1 indicates that the secondary endpoint buffer is full.
5
EPFULL0
A logic 1 indicates that the primary endpoint buffer is full.
4
DATA_PID
This bit indicates the data PID of the present packet
(0 = DATA PID, 1 = DATA1 PID).
3
OVERWRITE
This bit is set by hardware, a logic 1 indicating that a new Setup
packet has overwritten the previous setup information, before it
was acknowledged or before the endpoint was stalled. This bit is
cleared by reading, if writing the setup data has finished.
Firmware must check this bit before sending an Acknowledge
Setup command or stalling the endpoint. Upon reading a logic 1
the firmware must stop ongoing setup actions and wait for a new
Setup packet.
12.2.3
2
SETUPT
A logic 1 indicates that the buffer contains a Setup packet.
1
CPUBUF
This bit indicates which buffer is currently selected for CPU
access (0 = primary buffer, 1 = secondary buffer).
0
-
reserved
Stall Endpoint/Unstall Endpoint
These commands are used to stall or unstall an endpoint. The commands modify the
content of the Endpoint Status Register (see Table 32).
A stalled control endpoint is automatically unstalled when it receives a SETUP token,
regardless of the packet content. If the endpoint should stay in its stalled state, the
microcontroller can re-stall it with the Stall Endpoint command.
When a stalled endpoint is unstalled (either by the Unstall Endpoint command or by
receiving a SETUP token), it is also re-initialized. This flushes the buffer: if it is an
OUT buffer it waits for a DATA 0 PID, if it is an IN buffer it writes a DATA 0 PID.
Code (Hex): 40 to 4F — stall (control OUT, control IN, endpoint 1 to 14)
Code (Hex): 80 to 8F — unstall (control OUT, control IN, endpoint 1 to 14)
Transaction — none
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
35 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
12.2.4
Validate Endpoint Buffer
This command signals the presence of valid data for transmission to the USB host, by
setting the Buffer Full flag of the selected IN endpoint. This indicates that the data in
the buffer is valid and can be sent to the host, when the next IN token is received. For
a double-buffered endpoint this command switches the current FIFO for CPU access.
Remark: For special aspects of the control IN endpoint see Section 9.5.
Code (Hex): 61 to 6F — validate endpoint buffer (control IN, endpoint 1 to 14)
Transaction — none
12.2.5
Clear Endpoint Buffer
This command unlocks and clears the buffer of the selected OUT endpoint, allowing
the reception of new packets. Reception of a complete packet causes the Buffer Full
flag of an OUT endpoint to be set. Any subsequent packets are refused by returning a
NAK condition, until the buffer is unlocked using this command. For a double-buffered
endpoint this command switches the current FIFO for CPU access.
Remark: For special aspects of the control OUT endpoint see Section 9.5.
Code (Hex): 70, 72 to 7F — clear endpoint buffer (control OUT, endpoint 1 to 14)
Transaction — none
12.2.6
Check Endpoint Status
This command is used to check the status of the selected endpoint FIFO without
clearing any status or interrupt bits. The command accesses the Endpoint Status
Image Register, which contains a copy of the Endpoint Status Register. The bit
allocation of the Endpoint Status Image Register is shown in Table 34.
Code (Hex): D0 to DF — check status (control OUT, control IN, endpoint 1 to 14)
Transaction — write/read 1 byte
Table 34:
Endpoint Status Image Register: bit allocation
Bit
7
6
5
4
3
2
1
0
EPSTAL
EPFULL1
EPFULL0
DATA_PID
OVER
WRITE
SETUPT
CPUBUF
reserved
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
Symbol
Table 35:
Endpoint Status Image Register: bit description
Bit
Symbol
Description
7
EPSTAL
This bit indicates whether the endpoint is stalled or not
(1 = stalled, 0 = not stalled).
6
EPFULL1
A logic 1 indicates that the secondary endpoint buffer is full.
5
EPFULL0
A logic 1 indicates that the primary endpoint buffer is full.
4
DATA_PID
This bit indicates the data PID of the present packet
(0 = DATA0 PID, 1 = DATA1 PID).
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
36 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 35:
Endpoint Status Image Register: bit description…continued
Bit
Symbol
Description
3
OVERWRITE
This bit is set by hardware, a logic 1 indicating that a new Setup
packet has overwritten the previous setup information, before it
was acknowledged or before the endpoint was stalled. This bit is
cleared by reading, if writing the setup data has finished.
Firmware must check this bit before sending an Acknowledge
Setup command or stalling the endpoint. Upon reading a logic 1
the firmware must stop ongoing setup actions and wait for a new
Setup packet.
12.2.7
2
SETUPT
A logic 1 indicates that the buffer contains a Setup packet.
1
CPUBUF
This bit indicates which buffer is currently selected for CPU
access (0 = primary buffer, 1 = secondary buffer).
0
-
reserved
Acknowledge Setup
This command acknowledges to the host that a SETUP packet was received. The
arrival of a SETUP packet disables the Validate Buffer and Clear Buffer commands
for the control IN and OUT endpoints. The microcontroller needs to re-enable these
commands by sending an Acknowledge Setup command, see Section 9.5.
Remark: The Acknowledge Setup command must be sent to both control endpoints
(IN and OUT).
Code (Hex): F4 — acknowledge setup
Transaction — none
12.3 General commands
12.3.1
Read Endpoint Error Code
This command returns the status of the last transaction of the selected endpoint, as
stored in the Error Code Register. Each new transaction overwrites the previous
status information. The bit allocation of the Error Code Register is shown in Table 36.
Code (Hex): A0 to AF — read error code (control OUT, control IN, endpoint 1 to 14)
Transaction — read 1 byte
Table 36:
Error Code Register: bit allocation
Bit
Symbol
7
6
5
4
3
2
1
ERROR[3:0]
0
UNREAD
DATA01
reserved
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
RTOK
Rev. 04 — 30 October 2001
37 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 37:
Error Code Register: bit description
Bit
Symbol
Description
7
UNREAD
A logic 1 indicates that a new event occurred before the
previous status was read.
6
DATA01
This bit indicates the PID type of the last successfully received
or transmitted packet (0 = DATA0 PID, 1 = DATA1 PID).
5
-
reserved
4 to 1
ERROR[3:0]
Error code. For error description, see Table 38.
0
RTOK
A logic 1 indicates that data was received or transmitted
successfully.
Table 38:
12.3.2
Transaction error codes
Error code
(Binary)
Description
0000
no error
0001
PID encoding error; bits 7 to 4 are not the inverse of bits 3 to 0
0010
PID unknown; encoding is valid, but PID does not exist
0011
unexpected packet; packet is not of the expected type (token, data, or
acknowledge), or is a SETUP token to a non-control endpoint
0100
token CRC error
0101
data CRC error
0110
time-out error
0111
babble error
1000
unexpected end-of-packet
1001
sent or received NAK (Not AcKnowledge)
1010
sent Stall; a token was received, but the endpoint was stalled
1011
overflow; the received packet was larger than the available buffer space
1100
sent empty packet (ISO only)
1101
bit stuffing error
1110
sync error
1111
wrong (unexpected) toggle bit in DATA PID; data was ignored
Unlock Device
This command unlocks the ISP1181 from write-protection mode after a ‘resume’. In
‘suspend’ state all registers and FIFOs are write-protected to prevent data corruption
by external devices during a ‘resume’. Register access for reading is not blocked.
After waking up from ‘suspend’ state, the firmware must unlock the registers and
FIFOs via this command, by writing the unlock code (AA37H) into the Lock Register
(8-bit bus: lower byte first). The bit allocation of the Lock Register is given in Table 39.
Code (Hex): B0 — unlock the device
Transaction — write 2 bytes (unlock code)
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
38 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 39:
Lock Register: bit allocation
Bit
15
14
13
Symbol
12
11
10
9
8
UNLOCKH[7:0] = AAH
Reset
1
0
1
0
1
0
1
0
Access
W
W
W
W
W
W
W
W
Bit
7
6
5
4
3
2
1
0
Symbol
UNLOCKL[7:0] = 37H
Reset
0
0
1
1
0
1
1
1
Access
W
W
W
W
W
W
W
W
Table 40:
12.3.3
Error Code Register: bit description
Bit
Symbol
Description
15 to 0
UNLOCK[15:0]
Sending data AA37H unlocks the internal registers and FIFOs
for writing, following a ‘resume’.
Write/Read Scratch Register
This command accesses the 16-bit Scratch Register, which can be used by the
firmware to save and restore information, e.g. the device status before powering
down in ‘suspend’ state. The register bit allocation is given in Table 41.
Code (Hex): B2/B3 — write/read Scratch Register
Transaction — write/read 2 bytes
Table 41:
Scratch Information Register: bit allocation
Bit
Symbol
Reset
Access
Bit
15
14
13
12
reserved
Access
10
9
8
SFIRH[6:0]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
Symbol
Reset
11
SFIRL[7:0]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Table 42:
12.3.4
Scratch Information Register: bit description
Bit
Symbol
Description
15
-
reserved; must be logic 0
14 to 8
SFIRH[6:0]
Scratch Information Register (high byte)
7 to 0
SFIRL[7:0]
Scratch Information Register (low byte)
Read Frame Number
This command returns the frame number of the last successfully received SOF. It is
followed by reading one or two bytes from the Frame Number Register, containing the
frame number (lower byte first). The Frame Number Register is shown in Table 43.
Remark: After a bus reset, the value of the Frame Number Register is undefined.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
39 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Code (Hex): B4 — read frame number
Transaction — read 1 or 2 bytes
Table 43:
Frame Number Register: bit allocation
Bit
Symbol
15
14
13
12
11
reserved
reserved
reserved
reserved
reserved
10
9
8
SOFRH[2:0]
Reset[1]
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
Bit
7
6
5
4
3
2
1
0
Symbol
SOFRL[7:0]
Reset[1]
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
[1]
Reset value undefined after a bus reset.
Table 44:
A0
Phase
Bus lines
Byte #
Description
1
command
D[7:0]
-
command code (B4H)
0
data
D[7:0]
0
frame number (lower byte)
0
data
D[7:0]
1
frame number (upper byte)
Table 45:
Example of Frame Number Register access (16-bit bus width)
A0
Phase
Bus lines
Word #
Description
1
command
D[7:0]
-
command code (B4H)
D[15:8]
-
ignored
D[15:0]
0
frame number
0
12.3.5
Example of Frame Number Register access (8-bit bus width)
data
Read Chip ID
This command reads the chip identification code and hardware version number. The
firmware must check this information to determine the supported functions and
features. This command accesses the Chip ID Register, which is shown in Table 46.
Code (Hex): B5 — read chip ID
Transaction — read 2 bytes
Table 46:
Chip ID Register: bit allocation
Bit
15
14
13
Symbol
12
11
10
9
8
CHIPIDH[7:0]
Reset
81H
Access
R
R
R
R
R
R
R
R
Bit
7
6
5
4
3
2
1
0
R
R
R
Symbol
CHIPIDL[7:0]
Reset
Access
XXH
R
R
R
R
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
R
Rev. 04 — 30 October 2001
40 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 47:
12.3.6
Chip ID Register: bit description
Bit
Symbol
Description
15 to 8
CHIPIDH[7:0]
chip ID code (81H)
7 to 0
CHIPIDL[7:0]
silicon version (XXH, with XX representing the BCD encoded
version number)
Read Interrupt Register
This command indicates the sources of interrupts as stored in the 4-byte Interrupt
Register. Each individual endpoint has its own interrupt bit. The bit allocation of the
Interrupt Register is shown in Table 48. Bit BUSTATUS is used to verify the current
bus status in the interrupt service routine. Interrupts are enabled via the Interrupt
Enable Register, see Section 12.1.5.
While reading the interrupt register, please read all the 4 bytes completely.
Code (Hex): C0 — read interrupt register
Transaction — read 4 bytes
Table 48:
Interrupt Register: bit allocation
Bit
Symbol
31
30
29
28
27
26
25
24
reserved
reserved
reserved
reserved
reserved
reserved
reserved
reserved
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
Bit
23
22
21
20
19
18
17
16
EP14
EP13
EP12
EP11
EP10
EP9
EP8
EP7
Symbol
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
Bit
15
14
13
12
11
10
9
8
EP6
EP5
EP4
EP3
EP2
EP1
EP0IN
EP0OUT
Symbol
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
Bit
7
6
5
4
3
2
1
0
BUSTATUS
reserved
PSOF
SOF
EOT
SUSPND
RESUME
RESET
Symbol
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
41 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 49:
Interrupt Register: bit description
Bit
Symbol
Description
31 to 24
-
reserved
23 to 10
EP14 to EP1
A logic 1 indicates the interrupt source(s): endpoint 14 to 1
9
EP0IN
A logic 1 indicates the interrupt source: control IN endpoint
8
EP0OUT
A logic 1 indicates the interrupt source: control OUT endpoint
7
BUSTATUS
Monitors the current USB bus status (0 = awake, 1 = suspend).
6
-
reserved
5
PSOF
A logic 1 indicates that an interrupt is issued every 1 ms
because of the Pseudo SOF; after 3 missed SOFs ‘suspend’
state is entered.
4
SOF
A logic 1 indicates that a SOF condition was detected.
3
EOT
A logic 1 indicates that an internal EOT condition was generated
by the DMA Counter reaching zero.
2
SUSPND
A logic 1 indicates that an ‘awake’ to ‘suspend’ change of state
was detected on the USB bus.
1
RESUME
A logic 1 indicates that a ‘resume’ state was detected.
0
RESET
A logic 1 indicates that a bus reset condition was detected,
13. Interrupts
Figure 9 shows the interrupt logic of the ISP1181. Each of the indicated USB events
is logged in a status bit of the Interrupt Register. Corresponding bits in the Interrupt
Enable Register determine whether or not an event will generate an interrupt.
Interrupts can be masked globally by means of the INTENA bit of the Mode Register
(see Table 20).
The active level and signalling mode of the INT output is controlled by the INTPOL
and INTLVL bits of the Hardware Configuration Register (see Table 22). Default
settings after reset are active LOW and level mode. When pulse mode is selected, a
pulse of 166 ns is generated when the OR-ed combination of all interrupt bits
changes from logic 0 to logic 1.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
42 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
interrupt register
RESET
SUSPND
RESUME
.
.
.
SOF
EP14
.
.
.
...
.
.
.
EP0IN
EP0OUT
EOT
device mode
register
INTENA
interrupt enable
register
PULSE
GENERATOR
IERST
IESUSP
IERESM
IESOF
IEP14
.
.
.
1
hardware configuration
register
0
INTLVL
...
INTPOL
IEP0IN
INT
IEP0OUT
MGS772
IEEOT
Fig 9. Interrupt logic.
Bits RESET, RESUME, EOT and SOF are cleared upon reading the Interrupt
Register. The endpoint bits (EP0OUT to EP14) are cleared by reading the associated
Endpoint Status Register.
Bit BUSTATUS follows the USB bus status exactly, allowing the firmware to get the
current bus status when reading the Interrupt Register.
SETUP and OUT token interrupts are generated after ISP1181 has acknowledged
the associated data packet. In bulk transfer mode, the ISP1181 will issue interrupts
for every ACK received for an OUT token or transmitted for an IN token.
In isochronous mode, an interrupt is issued upon each packet transaction. The
firmware must take care of timing synchronization with the host. This can be done via
the Pseudo Start-Of-Frame (PSOF) interrupt, enabled via bit IEPSOF in the Interrupt
Enable Register. If a Start-Of-Frame is lost, PSOF interrupts are generated every
1 ms. This allows the firmware to keep data transfer synchronized with the host. After
3 missed SOF events the ISP1181 will enter ‘suspend’ state.
An alternative way of handling isochronous data transfer is to enable both the SOF
and the PSOF interrupts and disable the interrupt for each isochronous endpoint.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
43 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
14. Power supply
The ISP1181 is powered from a single supply voltage, ranging from 4.0 to 5.5 V. An
integrated voltage regulator provides a 3.3 V supply voltage for the internal logic and
the USB transceiver. This voltage is available at pin Vreg(3.3) for connecting an
external pull-up resistor on USB connection D+. See Figure 10.
The ISP1181 can also be operated from a 3.0 to 3.6 V supply, as shown in Figure 11.
In that case the internal voltage regulator is disabled and pin Vreg(3.3) must be
connected to VCC.
ISP1181
ISP1181
VCC
VCC
VCC(3.3)
4.0 to 5.5 V
VCC(3.3)
3.0 to 3.6 V
Vref
Vreg(3.3)
Vref
Vreg(3.3)
MGS773
MGS774
Fig 10. ISP1181 with a 4.0 to 5.5 V supply.
Fig 11. ISP1181 with a 3.0 to 3.6 V supply.
15. Crystal oscillator and LazyClock
The ISP1181 has a crystal oscillator designed for a 6 MHz parallel-resonant crystal
(fundamental). A typical circuit is shown in Figure 12. Alternatively, an external clock
signal of 6 MHz can be applied to input XTAL1, while leaving output XTAL2 open.
CLKOUT
ISP1181
18 pF
XTAL2
6 MHz
XTAL1
18 pF
MGS777
Fig 12. Typical oscillator circuit.
The 6 MHz oscillator frequency is multiplied to 48 MHz by an internal PLL. This
frequency is used to generate a programmable clock output signal at pin CLKOUT,
ranging from 3 to 48 MHz.
In ‘suspend’ state the normal CLKOUT signal is not available, because the crystal
oscillator and the PLL are switched off to save power. Instead, the CLKOUT signal
can be switched to the LazyClock frequency of 115 kHz ±10 %.
The oscillator operation and the CLKOUT frequency are controlled via the Hardware
Configuration Register, as shown in Figure 13. The following bits are involved:
• CLKRUN switches the oscillator on and off
• CLKDIV[3:0] is the division factor determining the normal CLKOUT frequency
• NOLAZY controls the LazyClock signal output during ‘suspend’ state.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
44 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
hardware
configuration
register
CLKRUN
SUSPEND
enable
.
.
.
XTAL OSC
6 MHz
enable
48 MHz
PLL 8×
N
4
CKDIV[3:0]
÷ (N + 1)
1
CLKOUT
0
NOLAZY
LAZYCLOCK
.
.
.
115 (±10%) kHz
enable
NOLAZY
MGS775
Fig 13. Oscillator and LazyClock logic.
When ISP1181 enters ‘suspend’ state (by setting and clearing bit GOSUSP in the
Mode Register), outputs SUSPEND and CLKOUT change state after approximately
2 ms delay. When NOLAZY = 0 the clock signal on output CLKOUT does not stop, but
changes to the 115 kHz ±10 % LazyClock frequency.
When resuming from ‘suspend’ state by a positive pulse on input WAKEUP, output
SUSPEND is cleared and the clock signal on CLKOUT restarted after a 0.5 ms delay.
The timing of the CLKOUT signal at ‘suspend’ and ‘resume’ is given in Figure 14.
GOSUSP
WAKEUP
1.8 to 2.2 ms
0.5 ms
SUSPEND
PLL circuit stable
3 to 4 ms
CLKOUT
MGS776
If enabled, the 115 kHz ±10 % LazyClock frequency will be output on pin CLKOUT during ‘suspend’ state.
Fig 14. CLKOUT signal timing at ‘suspend’ and ‘resume’.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
45 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
16. Power-on reset
The ISP1181 has an internal power-on reset (POR) circuit. Input pin RESET can be
directly connected to VCC. The clock signal on output CLKOUT starts 0.5 ms after
power-on and normally requires 3 to 4 ms to stabilize.
The triggering voltage of the POR circuit is 2.0 V nominal. A POR is automatically
generated when VCC goes below the trigger voltage for a duration longer than 50 µs.
POR
VCC
(1)
≤ 350 µs
2.0 V
0V
> 50 µs
1 ms
1 ms
t1
t2
t3
MGT026
t1: clock is running
t2: BUS_CONF pins are sampled
t3: registers are accessible
(1) Supply voltage (5 V or 3.3 V), connected externally to pin RESET.
Fig 15. Power-on reset timing.
A hardware reset disables all USB endpoints and clears all ECRs, except for the
control endpoint which is fixed and always enabled. Section 9.3 explains how to
(re-)initialize the endpoints.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
46 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
17. Limiting values
Table 50: Absolute maximum ratings
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
VCC
Min
Max
Unit
supply voltage
−0.5
+6.0
V
VI
input voltage
−0.5
VCC + 0.5
V
Ilatchup
latchup current
VI < 0 or VI > VCC
-
100
mA
Vesd
electrostatic discharge voltage
ILI < 1 µA
-
±2000
V
Tstg
storage temperature
−60
+150
°C
Ptot
total power dissipation
-
165
mW
[1]
[2]
Conditions
[1][2]
VCC = 5.5V
Equivalent to discharging a 100 pF capacitor via a 1.5 kΩ resistor (Human Body Model).
Values are given for device only; in-circuit Vesd(max) = ±8000 V.
Table 51:
Recommended operating conditions
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VCC
supply voltage
with regulator
4.0
5.0
5.5
V
without regulator
3.0
3.3
3.6
V
VI
input voltage
0
-
VCC
V
VI(AI/O)
input voltage on analog I/O pins
(D+/D−)
0
-
3.6
V
VO(od)
open-drain output pull-up voltage
0
-
VCC
V
Tamb
operating ambient temperature
−40
-
+85
°C
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
47 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
18. Static characteristics
Table 52: Static characteristics; supply pins
VGND = 0 V; Tamb = −40 to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
[1]
Min
Typ
Max
Unit
3.0[2]
3.3
3.6
V
Vreg(3.3)
regulated supply voltage
VCC = 4.0 to 5.5 V
ICC
operating supply current
VCC = 5.0 V; Tamb = 25°C
-
26
-
mA
VCC = 3.3 V; Tamb = 25°C
-
22
-
mA
ICC(susp)
suspend supply current
1.5 kΩ pull-up on
upstream port D+
(pin DP0)
-
-
265
µA
no pull-up on upstream
port D+ (pin DP0)
-
-
50
µA
202
µA
ICC(susp)
[1]
[2]
suspend supply current
VCC = 5.0 V; Tamb = 25°C
VCC = 3.3 V; Tamb = 25°C
1.5 kΩ pull-up on
upstream port D+
(pin DP0)
For 3.3 V operation, pin Vreg(3.3) must be connected to pin VCC(3.3).
In ‘suspend’ mode the minimum voltage is 2.7 V.
Table 53: Static characteristics: digital pins
VCC = 3.3 V ±10% or 5.0 V ±10%; VGND = 0 V; Tamb = −40 to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Input levels
VIL
LOW-level input voltage
-
-
0.8
V
VIH
HIGH-level input voltage
2.0
-
-
V
Schmitt trigger inputs
Vth(LH)
positive-going threshold
voltage
1.4
-
1.9
V
Vth(HL)
negative-going threshold
voltage
0.9
-
1.5
V
Vhys
hysteresis voltage
0.4
-
0.7
V
-
-
0.4
V
-
-
0.1
V
2.4
-
-
V
-
-
±5
µA
-
-
±5
µA
Output levels
VOL
LOW-level output voltage
IOL = rated drive
VOH
HIGH-level output voltage
IOH = rated drive
IOL = 20 µA
[1]
Leakage current
input leakage current
ILI
Open-drain outputs
OFF-state output current
IOZ
[1]
Not applicable for open-drain outputs.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
48 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Table 54: Static characteristics: analog I/O pins (D+, D−)[1]
VCC = 3.3 V ±10% or 5.0 V ±10%; VGND = 0 V; Tamb = −40 to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VDI
differential input sensitivity
|VI(D+) − VI(D−)|
0.2
-
-
V
VCM
differential common mode
voltage
includes VDI range
0.8
-
2.5
V
VIL
LOW-level input voltage
-
-
0.8
V
VIH
HIGH-level input voltage
2.0
-
-
V
Input levels
Output levels
VOL
LOW-level output voltage
RL = 1.5 kΩ to +3.6V
-
-
0.3
V
VOH
HIGH-level output voltage
RL = 15 kΩ to GND
2.8
-
3.6
V
-
-
±10
µA
Leakage current
OFF-state leakage current
ILZ
Capacitance
transceiver capacitance
pin to GND
-
-
20
pF
RPU
pull-up resistance on D+
SoftConnect = ON
1.1
-
1.9
kΩ
ZDRV[2]
driver output impedance
steady-state drive
29
-
44
Ω
ZINP
input impedance
10
-
-
MΩ
termination voltage for
upstream port pull-up (RPU)
3.0[4]
-
3.6
V
CIN
Resistance
Termination
VTERM[3]
[1]
[2]
[3]
[4]
D+ is the USB positive data pin; D− is the USB negative data pin.
Includes external resistors of 22 Ω ±1% on both D+ and D−.
This voltage is available at pin Vreg(3.3).
In ‘suspend’ mode the minimum voltage is 2.7 V.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
49 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
19. Dynamic characteristics
Table 55: Dynamic characteristics
VCC = 3.3 V ±10% or 5.0 V ±10%; VGND = 0 V; Tamb = −40 to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
pulse width on input RESET
crystal oscillator running
50
-
-
µs
-
0.5[1]
-
ms
-
6
-
MHz
Reset
tW(RESET)
crystal oscillator stopped
Crystal oscillator
fXTAL
[1]
crystal frequency
Dependent on the crystal oscillator start-up time.
Table 56: Dynamic characteristics: analog I/O pins (D+, D−)[1]
VCC = 3.3 V ±10% or 5.0 V ±10%; VGND = 0 V; Tamb = −40 to +85 °C; CL = 50 pF; RPU = 1.5 kΩ on D+ to VTERM; unless
otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Driver characteristics
tFR
rise time
CL = 50 pF;
10 to 90% of |VOH − VOL|
4
-
20
ns
tFF
fall time
CL = 50 pF;
90 to 10% of |VOH − VOL|
4
-
20
ns
FRFM
differential rise/fall time
matching (tFR/tFF)
90
-
111.11
%
VCRS
output signal crossover voltage
1.3
-
2.0
V
[2]
[2][3]
Data source timing
tFEOPT
tFDEOP
see Figure 16
[3]
160
-
175
ns
source differential data-to-EOP see Figure 16
transition skew
[3]
−2
-
+5
ns
source EOP width
Receiver timing
tJR1
receiver data jitter tolerance for see Figure 17
consecutive transitions
[3]
−18.5
-
+18.5
ns
tJR2
receiver data jitter tolerance for see Figure 17
paired transitions
[3]
−9
-
+9
ns
tFEOPR
receiver SE0 width
[3]
82
-
-
ns
tFST
width of SE0 during differential rejected as EOP; see
transition
Figure 18
[3]
-
-
14
ns
[1]
[2]
[3]
accepted as EOP; see
Figure 16
Test circuit: see Figure 34.
Excluding the first transition from Idle state.
Characterized only, not tested. Limits guaranteed by design.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
50 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
TPERIOD
+3.3 V
crossover point
extended
crossover point
differential
data lines
0V
differential data to
SE0/EOP skew
N × TPERIOD + t DEOP
source EOP width: t EOPT
receiver EOP width: t EOPR
MGR776
TPERIOD is the bit duration corresponding with the USB data rate.
Full-speed timing symbols have a subscript prefix ‘F’, low-speed timings a prefix ‘L’.
Fig 16. Source differential data-to-EOP transition skew and EOP width.
TPERIOD
+3.3 V
differential
data lines
0V
tJR
tJR1
tJR2
MGR871
consecutive
transitions
N × TPERIOD + t JR1
paired
transitions
N × TPERIOD + t JR2
TPERIOD is the bit duration corresponding with the USB data rate.
Fig 17. Receiver differential data jitter.
tFST
+3.3 V
VIH(min)
differential
data lines
0V
MGR872
Fig 18. Receiver SE0 width tolerance.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
51 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
19.1 Timing symbols
Table 57:
Legend for timing characteristics
Symbol
Description
Time symbols
t
time
T
cycle time (periodic signal)
Signal names
A
address;
DMA acknowledge (DACK)
C
clock;
command
D
data input;
E
chip enable
G
output enable
I
instruction (program memory content);
data
input (general)
L
address latch enable (ALE)
P
program store enable (PSEN, active LOW);
Q
data output
R
read signal (RD, active LOW);
propagation delay
read (action);
DMA request (DREQ)
S
chip select
W
write signal (WR, active LOW);
write (action);
pulse width
U
undefined
Y
output (general)
Logic levels
H
logic HIGH
L
logic LOW
P
stop, not active (OFF)
S
start, active (ON)
V
valid logic level
X
invalid logic level
Z
high-impedance (floating, three-state)
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
52 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
19.2 Parallel I/O timing
Table 58:
Dynamic characteristics: parallel interface timing
Symbol
Parameter
Conditions
8-bit bus
16-bit bus
Unit
Min
Max
Min
Max
Read timing (see Figure 19)
tRHAX
address hold time after RD
HIGH
3
-
3
-
ns
tAVRL
address setup time before RD
LOW
0
-
0
-
ns
tSHDZ
data outputs high-impedance
time after CS HIGH
-
3
-
3
ns
tRLRH
RD pulse width
25
-
25
-
ns
tRLDV
data valid time after RD LOW
-
22
-
22
ns
tSHRL
read interval after CS HIGH[1]
90
-
180
-
ns
Write timing (see Figure 20)
tWHAX
address hold time after WR
HIGH
3
-
3
-
ns
tAVWL
address setup time before WR
LOW
0
-
0
-
ns
tSHWL
write interval after CS HIGH[2]
90/180[3]
-
180
-
ns
tWLWH
WR pulse width
22
-
22
-
ns
tWHSH
chip deselect time after WR
HIGH
0
-
0
-
ns
tDVWH
data setup time before WR
HIGH
5
-
5
-
ns
tWHDZ
data hold time after WR HIGH
3
-
3
-
ns
ALE timing (see Figure 21)
tLH
ALE pulse width
20
-
20
-
ns
tAVLL
address setup time before ALE
LOW
10
-
10
-
ns
tLLAX
address hold time after ALE
LOW
reading
0
10
0
10
ns
writing
0
-
0
-
ns
[1]
[2]
[3]
Measured from CS going HIGH to CS and RD both going LOW.
Measured from CS going HIGH to CS and WR both going LOW.
Commands Acknowledge Setup, Clear Buffer, Validate Buffer and Write Endpoint Configuration require 180 ns to complete.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
53 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
t RHAX
A0
tAVRL
t SHDZ
CS/DACK
t SHRL(1)
t RLRH
RD
t RLDV
DATA
MGS787
(1) For tSHRL both CS and RD must be LOW.
Fig 19. Parallel interface read timing (I/O and 8237 compatible DMA).
t WHAX
A0
tAVWL
CS/DACK
t WLWH
t SHWL(1)
t WHSH
WR
t DVWH
t WHDZ
DATA
MGS789
(1) For tSHRL both CS and WR must be LOW.
Fig 20. Parallel interface write timing (I/O and 8237 compatible DMA).
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
54 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
t LH
ALE
t LLAX
t AVLL
AD
A0
D0
DATA
MGS790
Fig 21. ALE timing.
19.3 Access cycle timing
Table 59:
Dynamic characteristics: access cycle timing
Symbol
Parameter
Conditions
8-bit bus
Min[1]
16-bit bus
Max
Min[1]
Max
Unit
Write command + write data (see Figure 22 and Figure 23)
Tcy(WC-WD)
cycle time for write command,
then write data
100[2]
-
205
-
ns
Tcy(WD-WD)
cycle time for write data
90
-
205
-
ns
Tcy(WD-WC)
cycle time for write data, then
write command
90
-
205
-
ns
100[2]
-
205
-
ns
Write command + read data (see Figure 24 and Figure 25)
Tcy(WC-RD)
cycle time for write command,
then read data
Tcy(RD-RD)
cycle time for read data
90
-
205
-
ns
Tcy(RD-WC)
cycle time for read data, then
write command
90
-
205
-
ns
[1]
[2]
If the access cycle time is less than specified, the READY signal will be LOW until the internal processing has finished.
Commands Acknowledge Setup, Clear Buffer, Validate Buffer and Write Endpoint Configuration require 180 ns to complete.
DATA
command
data
Tcy(WC-WD)
data
Tcy(WD-WD)
WR
CS
MGT022
Fig 22. Write command + write data cycle timing.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
55 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
DATA
data
command
data
Tcy(WD-WC)
WR
(1)
RD
CS
MGT025
(1) Example: read data.
Fig 23. Write data + write command cycle timing.
DATA
command
data
data
WR
Tcy(WC-RD)
RD
Tcy(RD-RD)
CS
MGT023
Fig 24. Write command + read data cycle timing.
DATA
data
command
data
WR
Tcy(RD-WC)
RD
(1)
CS
MGT024
(1) Example: read data.
Fig 25. Read data + write command cycle timing.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
56 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
19.4 DMA timing: single-cycle mode
Table 60:
Dynamic characteristics: single-cycle DMA timing
Symbol
Parameter
Conditions
8-bit bus
Min
Max
16-bit bus
Min
Max
Unit
8237 compatible mode (see Figure 26)
tASRP
DREQ off after DACK on
-
40
-
40
ns
Tcy(DREQ)
cycle time signal DREQ
90
-
180
-
ns
Read in DACK-only mode (see Figure 27)
tASRP
DREQ off after DACK on
-
40
-
40
ns
tASAP
DACK pulse width
25
-
25
-
ns
90
-
180
-
ns
tASAP + tAPRS DREQ on after DACK off
tASDV
data valid after DACK on
-
22
-
22
ns
tAPDZ
data hold after DACK off
-
3
-
3
ns
-
40
-
40
ns
90
-
180
-
ns
Write in DACK-only mode (see Figure 28)
DREQ off after DACK on
tASRP
tASAP + tAPRS DREQ on after DACK off
tDVAP
data setup before DACK off
5
-
5
-
ns
tAPDZ
data hold after DACK off
3
-
3
-
ns
Single-cycle EOT (see Figure 29)
tRSIH
input RD/WR HIGH after
DREQ on
22
-
22
-
ns
tIHAP
DACK off after input RD/WR
HIGH
0
-
0
-
ns
tEOT
EOT pulse width
22
-
22
-
ns
tRLIS
input EOT on after RD LOW
-
22
-
89
ns
tWLIS
input EOT on after WR LOW
-
22
-
89
ns
EOT on;
DACK on;
RD/WR LOW
T cy(DREQ)
t ASRP
DREQ
DACK
MGS792
Fig 26. DMA timing in 8237 compatible mode.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
57 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
t ASRP
t APRS
DREQ
t ASAP
DACK
t APDZ
t ASDV
DATA
MGS793
Fig 27. DMA read timing in DACK-only mode.
t ASAP
t ASRP
t APRS
DREQ
t DVAP
t APDZ
DACK
DATA
MGS794
Fig 28. DMA write timing in DACK-only mode.
t RSIH
DREQ
t ASRP
t IHAP
(1)
DACK
RD/WR
(2)
t RLIS
tWLIS
t EOT
(3)
EOT
MGS795
(1) tASRP starts from DACK or RD/WR going LOW, whichever occurs later.
(2) The RD/WR signals are not used in DACK-only DMA mode.
(3) The EOT condition is considered valid if DACK, RD/WR and EOT are all active (= LOW).
Fig 29. EOT timing in single-cycle DMA mode.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
58 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
19.5 DMA timing: burst mode
Table 61:
Dynamic characteristics: burst mode DMA timing
Symbol
Parameter
Conditions
8-bit bus
16-bit bus
Min
Max
Min
Max
Unit
Burst (see Figure 30)
tRSIH
input RD/WR HIGH after
DREQ on
22
-
22
-
ns
tILRP
DREQ off after input RD/WR
LOW
-
60
-
60
ns
tIHAP
DACK off after input RD/WR
HIGH
0
-
0
-
ns
tIHIL
DMA burst repeat interval
(input RD/WR HIGH to LOW)
90
-
180
-
ns
22
-
22
-
ns
Burst EOT (see Figure 31)
tEOT
EOT pulse width
tISRP
DREQ off after input EOT on
-
40
-
40
ns
tRLIS
input EOT on after RD LOW
-
22
-
89
ns
tWLIS
input EOT on after WR LOW
-
22
-
89
ns
EOT on;
DACK on;
RD/WR LOW
t RSIH
t ILRP
DREQ
t IHAP
DACK
t IHIL
RD/WR
MGS796
Fig 30. Burst mode DMA timing.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
59 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
t ISRP
DREQ
DACK
t RLIS
tWLIS
RD/WR
t EOT(1)
EOT
MGS797
(1) The EOT condition is considered valid if DACK, RD/WR and EOT are all active (= LOW).
Fig 31. EOT timing in burst mode DMA.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
60 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
20. Application information
20.1 Typical interface circuits
VCC
A1
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
H8S/2357 D13
D14
D15
AD
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA8
DATA9
DATA10
DATA11
DATA12
DATA13
DATA14
DATA15
LINK LED
Vreg(3.3)
VCC
A0
ALE
CS
IRQ
RD
WR
P1.1
DREQ0
DACK
TEND
VBUS
BUS_CONF1
BUS_CONF0
1
22 Ω
D−
ISP1181
INT
SUSPEND
WAKEUP
DREQ
DACK
EOT
0.1
µF
USB
upstream
connector
D+
CSn
RD
WR
0.1
µF
RESET
2
3
22 Ω
4
XTAL1
XTAL2
> 330 Ω
GL
6 MHz
18 pF
18 pF
MGS769
Fig 32. Typical interface circuit for bus configuration mode 0 (shared ports: 16-bit PIO, 8-bit or 16-bit DMA).
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
61 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
VCC
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
ALE
8051
PSEN
RD
WR
IRQ
AD
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
LINK LED
Vreg(3.3)
VCC
P2.3
P2.0
P2.1
VBUS
ISP1181
DMA
CONTROLLER
D7
D6
D5
D4
D3
D2
D1
D0
2
3
22 Ω
4
RD
WR
XTAL1
XTAL2
> 330 Ω
GL
6 MHz
18 pF
BUS_CONF1
BUS_CONF0
CS1
CS2
RD
WR
DREQ
DACK
EOT
1
22 Ω
D−
INT
SUSPEND
WAKEUP
DREQ
DACK
EOT
BUS_REQ
BUS_GNT
MCU_WR
MCU_RD
0.1
µF
USB
upstream
connector
D+
A0
ALE
CS
0.1
µF
RESET
18 pF
CS
RD
WR
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
16 BIT
DMA PORT
MGS771
Fig 33. Typical interface circuit for bus configuration mode 2 (shared ports: 8-bit PIO, 8-bit or 16-bit DMA).
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
62 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
20.2 Interfacing ISP1181 with an H8S/2357 microcontroller
This section gives a summary of the ISP1181 interface with a H8S/2357 (or
compatible) microcontroller. Aspects discussed are: interrupt handling, address
mapping, DMA and I/O port usage for suspend and remote wake-up control. A typical
interface circuit is shown in Figure 32.
20.2.1
Interrupt handling
• ISP1181: program the Hardware Configuration register to select an active LOW
level for output INT (INTPOL = 0, see Table 21)
• H8S/2357: program the IRQ Sense Control Register (ISCRH and ISCRL) to
specify low-level sensing for the IRQ input.
20.2.2
Address mapping in H8S/2357
The H8S/2357 bus controller partitions its 16 Mbyte address space into eight areas
(0 to 7) of 2 Mbyte each. The bus controller will activate one of the outputs CS0 to
CS7 when external address space for the associated area is accessed.
The ISP1181 can be mapped to any address area, allowing easy interfacing when the
ISP1181 is the only device in that area. If in the example circuit for bus configuration
mode 0 (see Figure 32) the ISP1181 is mapped to address FFFF08H (in area 7),
output CS7 of the H8S/2357 can be directly connected to input CS of the ISP1181.
The external bus specifications, bus width, number of access states and number of
program wait states can be programmed for each address area. The recommended
settings of H8S/2357 for interfacing the ISP1181 are:
• 8-bit bus in Bus Width Control Register (ABWCR)
• enable wait states in Access State Control Register (ASTCR)
• 1 program wait state in the Wait Control Register (WCRH and WCRL).
20.2.3
Using DMA
The ISP1181 can be configured for several methods of DMA with the H8S/2357 and
other devices. The interface circuit in Figure 32 shows an example of the ISP1181
working with the H8S/2357 in single-address DACK-only DMA mode. External
devices are not shown.
For single-address DACK-only mode, firmware must program the following settings:
• ISP1181:
– program the DMA Counter register with the total transfer byte count
– program the Hardware Configuration Register to select active level LOW for
DREQ and DACK
– select the target endpoint and transfer direction
– select DACK-only mode and enable DMA transfer.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
63 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
20.2.4
Using H8S2357 I/O Ports
In the interface circuit of Figure 32 pin P1.1 of the H8S/2357 is configured as a
general purpose output port. This pin drives the ISP1181’s WAKEUP input to
generate a remote wake-up.
The H8S/2357 has 3 registers to configure port 1: Port 1 Data Direction Register
(P1DDR), Port 1 Data Register (P1DR) and Port 1 Register (PORT1). Only registers
P1DDR and P1DR must be configured, register PORT1 is only used to read the
actual levels on the port pins.
• H8S/2357:
– select pin P1.1 to be an output in register P1DDR
– program the desired bit value for P1.1 in register P1DR.
21. Test information
The dynamic characteristics of the analog I/O ports (D+ and D−) as listed in Table 56,
were determined using the circuit shown in Figure 34.
test point
22 Ω
D.U.T
CL
50 pF
15 kΩ
MGS784
Load capacitance:
CL = 50 pF (full-speed mode)
Speed:
full-speed mode only: internal 1.5 kΩ pull-up resistor on D+
Fig 34. Load impedance for D+ and D− pins.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
64 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
22. Package outline
TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1 mm
SOT362-1
E
D
A
X
c
HE
y
v M A
Z
48
25
Q
A2
(A 3)
A1
pin 1 index
A
θ
Lp
L
1
detail X
24
w M
bp
e
2.5
0
5 mm
scale
DIMENSIONS (mm are the original dimensions).
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (2)
e
HE
L
Lp
Q
v
w
y
Z
θ
mm
1.2
0.15
0.05
1.05
0.85
0.25
0.28
0.17
0.2
0.1
12.6
12.4
6.2
6.0
0.5
8.3
7.9
1
0.8
0.4
0.50
0.35
0.25
0.08
0.1
0.8
0.4
8
0o
o
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
REFERENCES
IEC
SOT362-1
JEDEC
EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
95-02-10
99-12-27
MO-153
Fig 35. TSSOP48 package outline.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
65 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
HVQFN48: plastic, heatsink very thin quad flat package; no leads;
48 terminals; body 7 x 7 x 0.85 mm
SOT619-3
B
D
D1
A
terminal 1
index area
A
E1
A4
A1
E
detail X
C
e1
1/2 e
e
13
y
y1 C
∅v M C A B
b
∅w M C
24
L
25
12
e
e2
Eh
1/2 e
pin 1 index
1
36
48
37
Dh
X
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
A
UNIT max.
mm
1.00
OUTLINE
VERSION
A1
A4
b
D
D1
Dh
E
E1
Eh
e
e1
e2
L
v
w
y
y1
0.05
0
0.80
0.65
0.30
0.18
7.15
6.85
6.85
6.65
5.25
4.95
7.15
6.85
6.85
6.65
5.25
4.95
0.5
5.5
5.5
0.50
0.30
0.2
0.1
0.08
0.1
REFERENCES
IEC
SOT619-3
JEDEC
EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
01-08-31
01-09-07
MO-220
Fig 36. HVQFN48 package outline.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
66 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
23. Soldering
23.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages (document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is recommended.
23.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 250 °C. The top-surface
temperature of the packages should preferable be kept below 220 °C for thick/large
packages, and below 235 °C small/thin packages.
23.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
• Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
• For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be
parallel to the transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
• For packages with leads on four sides, the footprint must be placed at a 45° angle
to the transport direction of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side corners.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
67 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time is 4 seconds at 250 °C. A mildly-activated flux will eliminate the
need for removal of corrosive residues in most applications.
23.4 Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low
voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time
must be limited to 10 seconds at up to 300 °C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 to 5 seconds between 270 and 320 °C.
23.5 Package related soldering information
Table 62:
Suitability of surface mount IC packages for wave and reflow soldering
methods
Package
Soldering method
BGA, HBGA, LFBGA, SQFP, TFBGA
Reflow[1]
not suitable
suitable
suitable[2]
HBCC, HLQFP, HSQFP, HSOP, HTQFP,
HTSSOP, HVQFN, SMS
not
PLCC[3], SO, SOJ
suitable
LQFP, QFP, TQFP
SSOP, TSSOP, VSO
[1]
[2]
[3]
[4]
[5]
suitable
suitable
not
recommended[3][4]
suitable
not
recommended[5]
suitable
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal
or external package cracks may occur due to vaporization of the moisture in them (the so called
popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated
Circuit Packages; Section: Packing Methods.
These packages are not suitable for wave soldering. On versions with the heatsink on the bottom
side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with
the heatsink on the top side, the solder might be deposited on the heatsink surface.
If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave
direction. The package footprint must incorporate solder thieves downstream and at the side corners.
Wave soldering is only suitable for LQFP, QFP and TQFP packages with a pitch (e) equal to or larger
than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than
0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Wave
Rev. 04 — 30 October 2001
68 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
24. Revision history
Table 63:
Revision history
Rev Date
04
20011030
CPCN
Description
-
Product data; fourth version. Supersedes ISP1181-03 of June 11th, 2001
(9397 750 08504). Modifications:
•
•
•
•
•
•
•
•
Added new USB basic speed logo to indicate ISP1181 as a USB-IF certified product.
In Table 50 “Absolute maximum ratings”, changed the condition ILI < 1 µA.
In Table 50 “Absolute maximum ratings”, removed table note 3.
In Table 50 “Absolute maximum ratings”, changed Vesd to ±2000 V.
Section 4; Table 1 on page 2: ISP1181BS, package version SOT619-2 replaced by
SOT619-3.
Section 22; Figure 36 on page 66: New drawing for SOT619-3.
In Table 46 on page 40, changed the reset value for CHIPIDL[7:0] from X0H to XXH.
In Table 50 “Absolute maximum ratings”, changed the value of latchup current from
200 mA to 100 mA.
03
20010611
-
Product data; third version. Supersedes ISP1181-02 of 2 January 2001
(9397 750 07366).
02
20010102
-
Objective specification; second version. Supersedes ISP1181-01 of 13 March 2000
(9397 750 06896).
01
20000313
-
Objective specification; initial version.
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Product data
Rev. 04 — 30 October 2001
69 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
25. Data sheet status
Data sheet status[1]
Product status[2]
Definition
Objective data
Development
This data sheet contains data from the objective specification for product development. Philips Semiconductors
reserves the right to change the specification in any manner without notice.
Preliminary data
Qualification
This data sheet contains data from the preliminary specification. Supplementary data will be published at a
later date. Philips Semiconductors reserves the right to change the specification without notice, in order to
improve the design and supply the best possible product.
Product data
Production
This data sheet contains data from the product specification. Philips Semiconductors reserves the right to
make changes at any time in order to improve the design, manufacturing and supply. Changes will be
communicated according to the Customer Product/Process Change Notification (CPCN) procedure
SNW-SQ-650A.
[1]
Please consult the most recently issued data sheet before initiating or completing a design.
[2]
The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at
URL http://www.semiconductors.philips.com.
26. Definitions
customers using or selling these products for use in such applications do so
at their own risk and agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.
Short-form specification — The data in a short-form specification is
extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Right to make changes — Philips Semiconductors reserves the right to
make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve
design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no
licence or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are
free from patent, copyright, or mask work right infringement, unless otherwise
specified.
Limiting values definition — Limiting values given are in accordance with
the Absolute Maximum Rating System (IEC 60134). Stress above one or
more of the limiting values may cause permanent damage to the device.
These are stress ratings only and operation of the device at these or at any
other conditions above those given in the Characteristics sections of the
specification is not implied. Exposure to limiting values for extended periods
may affect device reliability.
Application information — Applications that are described herein for any
of these products are for illustrative purposes only. Philips Semiconductors
make no representation or warranty that such applications will be suitable for
the specified use without further testing or modification.
27. Disclaimers
Life support — These products are not designed for use in life support
appliances, devices, or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors
28. Trademarks
ACPI — is an open industry specification for PC power management,
co-developed by Intel Corp., Microsoft Corp. and Toshiba
GoodLink — is a trademark of Koninklijke Philips Electronics N.V.
OnNow — is a trademark of Microsoft Corp.
SoftConnect — is a trademark of Koninklijke Philips Electronics N.V.
Zip — is a registered trademark of Iomega Corp.
Contact information
For additional information, please visit http://www.semiconductors.philips.com.
For sales office addresses, send e-mail to: [email protected].
Product data
Fax: +31 40 27 24825
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
9397 750 08938
Rev. 04 — 30 October 2001
70 of 71
ISP1181
Philips Semiconductors
Full-speed USB interface
Contents
1
2
3
4
5
6
6.1
6.2
7
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
8
9
9.1
9.2
9.3
9.4
9.5
10
10.1
10.2
10.3
10.4
10.4.1
10.4.2
11
11.1
11.1.1
11.2
11.3
12
12.1
12.1.1
12.1.2
12.1.3
12.1.4
12.1.5
12.1.6
12.1.7
12.1.8
12.2
12.2.1
12.2.2
General description . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pinning information. . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Functional description . . . . . . . . . . . . . . . . . . . . . . . . 9
Analog transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Philips Serial Interface Engine (SIE) . . . . . . . . . . . . . 9
Memory Management Unit (MMU) and integrated
RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SoftConnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
GoodLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Bit clock recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PLL clock multiplier . . . . . . . . . . . . . . . . . . . . . . . . . 10
Parallel I/O (PIO) and Direct Memory Access
(DMA) interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Modes of operation . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Endpoint descriptions. . . . . . . . . . . . . . . . . . . . . . . . 11
Endpoint access. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Endpoint FIFO size . . . . . . . . . . . . . . . . . . . . . . . . . 12
Endpoint initialization . . . . . . . . . . . . . . . . . . . . . . . . 14
Endpoint I/O mode access . . . . . . . . . . . . . . . . . . . . 14
Special actions on control endpoints . . . . . . . . . . . . 14
DMA transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Selecting an endpoint for DMA transfer . . . . . . . . . . 15
8237 compatible mode. . . . . . . . . . . . . . . . . . . . . . . 16
DACK-only mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
End-Of-Transfer conditions. . . . . . . . . . . . . . . . . . . . 18
Bulk endpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Isochronous endpoints . . . . . . . . . . . . . . . . . . . . . . . 19
Suspend and resume . . . . . . . . . . . . . . . . . . . . . . . . 20
Suspend conditions . . . . . . . . . . . . . . . . . . . . . . . . . 20
Powered-off application . . . . . . . . . . . . . . . . . . . . . . 21
Resume conditions. . . . . . . . . . . . . . . . . . . . . . . . . . 23
Control bits in suspend and resume. . . . . . . . . . . . . 23
Commands and registers . . . . . . . . . . . . . . . . . . . . . 24
Initialization commands . . . . . . . . . . . . . . . . . . . . . . 26
Write/Read Endpoint Configuration . . . . . . . . . . . . . 26
Write/Read Device Address . . . . . . . . . . . . . . . . . . . 27
Write/Read Mode Register. . . . . . . . . . . . . . . . . . . . 27
Write/Read Hardware Configuration . . . . . . . . . . . . 28
Write/Read Interrupt Enable Register . . . . . . . . . . . 30
Write/Read DMA Configuration . . . . . . . . . . . . . . . . 31
Write/Read DMA Counter . . . . . . . . . . . . . . . . . . . . 32
Reset Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Data flow commands . . . . . . . . . . . . . . . . . . . . . . . . 33
Write/Read Endpoint Buffer . . . . . . . . . . . . . . . . . . . 33
Read Endpoint Status . . . . . . . . . . . . . . . . . . . . . . . 34
© Koninklijke Philips Electronics N.V. 2001.
Printed in The Netherlands
All rights are reserved. Reproduction in whole or in part is prohibited without the prior
written consent of the copyright owner.
The information presented in this document does not form part of any quotation or
contract, is believed to be accurate and reliable and may be changed without notice. No
liability will be accepted by the publisher for any consequence of its use. Publication
thereof does not convey nor imply any license under patent- or other industrial or
intellectual property rights.
Date of release: 30 October 2001
Document order number: 9397 750 08938
12.2.3
12.2.4
12.2.5
12.2.6
12.2.7
12.3
12.3.1
12.3.2
12.3.3
12.3.4
12.3.5
12.3.6
13
14
15
16
17
18
19
19.1
19.2
19.3
19.4
19.5
20
20.1
20.2
20.2.1
20.2.2
20.2.3
20.2.4
21
22
23
23.1
23.2
23.3
23.4
23.5
24
25
26
27
28
Stall Endpoint/Unstall Endpoint . . . . . . . . . . . . . . . .
Validate Endpoint Buffer . . . . . . . . . . . . . . . . . . . . . .
Clear Endpoint Buffer . . . . . . . . . . . . . . . . . . . . . . . .
Check Endpoint Status . . . . . . . . . . . . . . . . . . . . . . .
Acknowledge Setup . . . . . . . . . . . . . . . . . . . . . . . . .
General commands . . . . . . . . . . . . . . . . . . . . . . . . .
Read Endpoint Error Code . . . . . . . . . . . . . . . . . . . .
Unlock Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Write/Read Scratch Register . . . . . . . . . . . . . . . . . .
Read Frame Number . . . . . . . . . . . . . . . . . . . . . . . .
Read Chip ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Read Interrupt Register . . . . . . . . . . . . . . . . . . . . . .
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crystal oscillator and LazyClock . . . . . . . . . . . . . . .
Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limiting values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Static characteristics . . . . . . . . . . . . . . . . . . . . . . . . .
Dynamic characteristics . . . . . . . . . . . . . . . . . . . . . .
Timing symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel I/O timing . . . . . . . . . . . . . . . . . . . . . . . . . . .
Access cycle timing . . . . . . . . . . . . . . . . . . . . . . . . .
DMA timing: single-cycle mode . . . . . . . . . . . . . . . .
DMA timing: burst mode . . . . . . . . . . . . . . . . . . . . . .
Application information . . . . . . . . . . . . . . . . . . . . . . .
Typical interface circuits . . . . . . . . . . . . . . . . . . . . . .
Interfacing ISP1181 with an H8S/2357
microcontroller . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt handling . . . . . . . . . . . . . . . . . . . . . . . . . . .
Address mapping in H8S/2357 . . . . . . . . . . . . . . . . .
Using DMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using H8S2357 I/O Ports . . . . . . . . . . . . . . . . . . . . .
Test information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soldering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction to soldering surface mount packages . .
Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual soldering . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package related soldering information . . . . . . . . . . .
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data sheet status . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
36
36
36
37
37
37
38
39
39
40
41
42
44
44
46
47
48
50
52
53
55
57
59
61
61
63
63
63
63
64
64
65
67
67
67
67
68
68
69
70
70
70
70