AD ADE7763ARS

Single-Phase Active and Apparent
Energy Metering IC
ADE7763
FEATURES
required to perform active and apparent energy measurements,
line-voltage period measurements, and rms calculation on the
voltage and current channels. The selectable on-chip digital
integrator provides direct interface to di/dt current sensors such
as Rogowski coils, eliminating the need for an external analog
integrator and resulting in excellent long-term stability and
precise phase matching between the current and the voltage
channels.
High accuracy; supports IEC 61036/60687, IEC62053-21, and
IEC62053-22
On-chip digital integrator enables direct interface-to-current
sensors with di/dt output
A PGA in the current channel allows direct interface to
shunts and current transformers
Active and apparent energy, sampled waveform, and current
and voltage rms
Less than 0.1% error in active energy measurement over a
dynamic range of 1000 to 1 at 25°C
Positive-only energy accumulation mode available
On-chip user programmable threshold for line voltage surge
and SAG and PSU supervisory
Digital calibration for power, phase, and input offset
On-chip temperature sensor (±3°C typical)
SPI®-compatible serial interface
Pulse output with programmable frequency
Interrupt request pin (IRQ) and status register
Reference 2.4 V with external overdrive capability
Single 5 V supply, low power (25 mW typical)
The ADE7763 provides a serial interface to read data and a
pulse output frequency (CF) that is proportional to the active
power. Various system calibration features such as channel
offset correction, phase calibration, and power calibration
ensure high accuracy. The part also detects short duration, low
or high voltage variations.
The positive-only accumulation mode gives the option to
accumulate energy only when positive power is detected. An
internal no-load threshold ensures that the part does not exhibit
any creep when there is no load. The zero-crossing output (ZX)
produces a pulse that is synchronized to the zero-crossing point
of the line voltage. This signal is used internally in the line cycle
active and apparent energy accumulation modes, which enables
faster calibration.
GENERAL DESCRIPTION
The ADE77631 features proprietary ADCs and fixed function
DSP for high accuracy over large variations in environmental
conditions and time. The ADE7763 incorporates two secondorder, 16-bit Σ-∆ ADCs, a digital integrator (on Ch1), reference
circuitry, a temperature sensor, and all the signal processing
The interrupt status register indicates the nature of the interrupt,
and the interrupt enable register controls which event produces
an output on the IRQ pin, an open-drain, active low logic output.
The ADE7763 is available in a 20-lead SSOP package.
FUNCTIONAL BLOCK DIAGRAM
AVDD
DVDD
RESET
DGND
INTEGRATOR
PGA
WGAIN[11:0]
MULTIPLIER
V1P
ADE7763
LPF2
dt
ADC
V1N
HPF1
TEMP
SENSOR
APOS[15:0]
CFNUM[11:0]
IRMSOS[11:0]
PGA
VRMSOS[11:0]
Φ
ADC
CFDEN[11:0]
x2
V2N
VADIV[7:0]
PHCAL[5:0]
AGND
%
%
WDIV[7:0]
LPF1
ZX
4kΩ
REFIN/OUT
CF
SAG
REGISTERS AND
SERIAL INTERFACE
CLKIN CLKOUT
DIN DOUT SCLK
CS
IRQ
04481-A-001
V2P
2.4V
REFERENCE
DFC
VAGAIN[11:0]
x2
Figure 1.
1
U.S. Patents 5,745,323; 5,760,617; 5,862,069; 5,872,469; others pending.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703
© 2004 Analog Devices, Inc. All rights reserved.
ADE7763
TABLE OF CONTENTS
Specifications..................................................................................... 3
Energy-to-Frequency Conversion............................................ 28
Timing Characteristics..................................................................... 5
Line Cycle Energy Accumulation Mode ................................. 30
Absolute Maximum Ratings............................................................ 6
Positive-Only Accumulation Mode ......................................... 30
ESD Caution.................................................................................. 6
No-Load Threshold.................................................................... 30
Terminology ...................................................................................... 7
Apparent Power Calculation..................................................... 31
Pin Configuration and Function Descriptions............................. 8
Apparent Energy Calculation ................................................... 32
Typical Performance Characteristics ........................................... 10
Line Apparent Energy Accumulation...................................... 33
Theory of Operation ...................................................................... 13
Energies Scaling.......................................................................... 34
Analog Inputs.............................................................................. 13
Calibrating an Energy Meter .................................................... 34
di/dt Current Sensor and Digital Integrator ........................... 14
CLKIN Frequency ...................................................................... 43
Zero-Crossing Detection........................................................... 15
Suspending Functionality.......................................................... 44
Period Measurement .................................................................. 16
Checksum Register..................................................................... 44
Power Supply Monitor ............................................................... 16
Serial Interface ............................................................................ 44
Line Voltage Sag Detection ....................................................... 17
Registers........................................................................................... 47
Peak Detection ............................................................................ 17
Register Descriptions ..................................................................... 50
Interrupts..................................................................................... 18
Communication Register .......................................................... 50
Temperature Measurement ....................................................... 19
Mode Register (0x09)................................................................. 50
Analog-to-Digital Conversion.................................................. 19
Interrupt Status Register (0x0B), Reset Interrupt Status
Register (0x0C), Interrupt Enable Register (0x0A) ............... 52
Channel 1 ADC .......................................................................... 20
Channel 2 ADC .......................................................................... 22
Phase Compensation.................................................................. 24
Active Power Calculation .......................................................... 25
CH1OS Register (0x0D)............................................................ 53
Outline Dimensions ....................................................................... 54
Ordering Guide .......................................................................... 54
Energy Calculation..................................................................... 26
Power Offset Calibration ........................................................... 28
REVISION HISTORY
10/04—Data Sheet Changed from Rev. 0 to Rev. A
Changes to Period Measurement Section ..................................16
Changes to Temperature Measurement Section........................19
Change to Energy-to-Frequency Conversion Section..............28
Update to Figure 61 .......................................................................29
Change to Apparent Energy Calculation Section .....................32
Change to Description of AEHF and VAEHF Bits ...................52
4/04—Revision 0: Initial Version
Rev. A | Page 2 of 56
ADE7763
SPECIFICATIONS
AVDD = DVDD = 5 V ± 5%, AGND = DGND = 0 V, on-chip reference, CLKIN = 3.579545 MHz XTAL, TMIN to TMAX = –40°C to +85°C.
Table 1. Specifications1, 2
Parameter
ENERGY MEASUREMENT ACCURACY
Active Power Measurement Error
Channel 1 Range = 0.5 V Full Scale
Gain = 1
Gain = 2
Gain = 4
Gain = 8
Channel 1 Range = 0.25 V Full Scale
Gain = 1
Gain = 2
Gain = 4
Gain = 8
Channel 1 Range = 0.125 V Full Scale
Gain = 1
Gain = 2
Gain = 4
Gain = 8
Active Power Measurement Bandwidth
Phase Error 1 between Channels
AC Power Supply Rejection1
Output Frequency Variation (CF)
DC Power Supply Rejection1
Output Frequency Variation (CF)
IRMS Measurement Error
IRMS Measurement Bandwidth
VRMS Measurement Error
VRMS Measurement Bandwidth
ANALOG INPUTS3
Maximum Signal Levels
Input Impedance (dc)
Bandwidth
Gain Error1, 3
Channel 1
Range = 0.5 V Full Scale
Range = 0.25 V Full Scale
Range = 0.125 V Full Scale
Channel 2
Offset Error 1
Channel 1
Channel 2
Spec
Unit
Test Conditions/Comments
0.1
0.1
0.1
0.1
% typ
% typ
% typ
% typ
CLKIN = 3.579545 MHz
Channel 2 = 300 mV rms/60 Hz, gain = 2
Over a dynamic range 1000 to 1
Over a dynamic range 1000 to 1
Over a dynamic range 1000 to 1
Over a dynamic range 1000 to 1
0.1
0.1
0.1
0.2
% typ
% typ
% typ
% typ
Over a dynamic range 1000 to 1
Over a dynamic range 1000 to 1
Over a dynamic range 1000 to 1
Over a dynamic range 1000 to 1
0.1
0.1
0.2
0.2
14
±0.05
% typ
% typ
% typ
% typ
kHz
max
Over a dynamic range 1000 to 1
Over a dynamic range 1000 to 1
Over a dynamic range 1000 to 1
Over a dynamic range 1000 to 1
0.2
% typ
±0.3
% typ
0.5
14
0.5
140
% typ
kHz
% typ
Hz
±0.5
390
14
V max
k min
kHz
±4
±4
±4
±4
±32
±13
±32
±13
% typ
% typ
% typ
% typ
mV max
mV max
mV max
mV max
Line frequency = 45 Hz to 65 Hz, HPF on
AVDD = DVDD = 5 V + 175 mV rms/120 Hz
Channel 1 = 20 mV rms, gain = 16, range = 0.5 V
Channel 2 = 300 mV rms/60 Hz, gain = 1
AVDD = DVDD = 5 V ± 250 mV dc
Channel 1 = 20 mV rms/60 Hz, gain = 16, range = 0.5 V
Channel 2 = 300 mV rms/60 Hz, gain = 1
Over a dynamic range 100 to 1
Over a dynamic range 20 to 1
See the Analog Inputs section
V1P, V1N, V2N, and V2P to AGND
CLKIN/256, CLKIN = 3.579545 MHz
External 2.5 V reference, gain = 1 on Channels 1 and 2
V1 = 0.5 V dc
V1 = 0.25 V dc
V1 = 0.125 V dc
V2 = 0.5 V dc
Gain 1
Gain 16
Gain 1
Gain 16
Rev. A | Page 3 of 56
ADE7763
Parameter
WAVEFORM SAMPLING
Channel 1
Signal-to-Noise Plus Distortion
Bandwidth (–3 dB)
Channel 2
Signal-to-Noise Plus Distortion
Bandwidth (–3 dB)
REFERENCE INPUT
REFIN/OUT Input Voltage Range
Input Capacitance
ON-CHIP REFERENCE
Reference Error
Current Source
Output Impedance
Temperature Coefficient
CLKIN
Input Clock Frequency
LOGIC INPUTS
RESET, DIN, SCLK, CLKIN, and CS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
Input Capacitance, CIN
LOGIC OUTPUTS
SAG and IRQ
Output High Voltage, VOH
Output Low Voltage, VOL
ZX and DOUT
Output High Voltage, VOH
Output Low Voltage, VOL
CF
Output High Voltage, VOH
Output Low Voltage, VOL
POWER SUPPLY
AVDD
DVDD
AIDD
DIDD
Spec
Unit
Test Conditions/Comments
Sampling CLKIN/128, 3.579545 MHz/128 = 27.9 kSPS
See the Channel 1 Sampling section
150 mV rms/60 Hz, range = 0.5 V, gain = 2
CLKIN = 3.579545 MHz
See the Channel 2 Sampling section
150 mV rms/60 Hz, gain = 2
CLKIN = 3.579545 MHz
62
14
dB typ
kHz
60
140
dB typ
Hz
2.6
2.2
10
V max
V min
pF max
±200
10
3.4
30
mV max
µA max
kΩ min
ppm/°C typ
4
1
MHz max
MHz min
2.4
0.8
±3
10
V min
V max
µA max
pF max
4
0.4
V min
V max
Open-drain outputs, 10 kΩ pull-up resistor
ISOURCE = 5 mA
ISINK = 0.8 mA
4
0.4
V min
V max
ISOURCE = 5 mA
ISINK = 0.8 mA
4
1
V min
V max
4.75
5.25
4.75
5.25
3
4
V min
V max
V min
V max
mA max
mA max
ISOURCE = 5 mA
ISINK = 7 mA
For specified performance
5 V – 5%
5 V + 5%
5 V – 5%
5 V + 5%
Typically 2.0 mA
Typically 3.0 mA
2.4 V + 8%
2.4 V – 8%
Nominal 2.4 V at REFIN/OUT pin
All specifications CLKIN of 3.579545 MHz
DVDD = 5 V ± 10%
DVDD = 5 V ± 10%
Typically 10 nA, VIN = 0 V to DVDD
__________________________________________________________
2
3
See the Terminology section for explanation of specifications.
See the plots in the Typical Performance Characteristics section.
See the Analog Inputs section.
200 µA
TO
OUTPUT
PIN
IOl
+2.1V
CL
50pF
1.6mA
IOH
04481-A-002
1
Figure 2. Load Circuit for Timing Specifications
Rev. A | Page 4 of 56
ADE7763
TIMING CHARACTERISTICS
AVDD = DVDD = 5 V ± 5%, AGND = DGND = 0 V, on-chip reference, CLKIN = 3.579545 MHz XTAL, TMIN to TMAX = −40°C to +85°C.
Table 2. Timing Characteristics1, 2
Parameter
Write Timing
t1
t2
t3
t4
t5
t6
t7
t8
Spec
Unit
Test Conditions/Comments
50
50
50
10
5
400
50
100
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min)
CS falling edge to first SCLK falling edge.
SCLK logic high pulse width.
SCLK logic low pulse width.
Valid data setup time before falling edge of SCLK.
Data hold time after SCLK falling edge.
Minimum time between the end of data byte transfers.
Minimum time between byte transfers during a serial write.
CS hold time after SCLK falling edge.
Read Timing
t93
4
µs min
t10
t11
50
30
ns min
ns min
t124
100
10
100
10
ns max
ns min
ns max
ns min
Minimum time between read command (i.e., a write to
communication register) and data read.
Minimum time between data byte transfers during a multibyte read.
Data access time after SCLK rising edge following a write to the
communication register.
Bus relinquish time after falling edge of SCLK.
t135
Bus relinquish time after rising edge of CS.
________________________________________________
1
Sample tested during initial release and after any redesign or process change that could affect this parameter. All input signals are specified with tr = tf = 5 ns (10% to
90%) and timed from a voltage level of 1.6 V.
2
See Figure 3, Figure 4, and the Serial Interface section.
3
Minimum time between read command and data read for all registers except waveform register, which is t9 = 500 ns min.
4
Measured with the load circuit in Figure 2 and defined as the time required for the output to cross 0.8 V or 2.4 V.
5
Derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit in Figure 2. The measured number is then extrapolated back
to remove the effects of charging or discharging the 50 pF capacitor. This means that the time quoted in the timing characteristics is the true bus relinquish time of
the part and is independent of the bus loading.
t8
CS
t6
t3
t7
t7
SCLK
t4
t2
0
1
DIN
A5
A4
t5
A3
A2
A1
DB7
A0
MOST SIGNIFICANT BYTE
COMMAND BYTE
DB0
DB7
DB0
LEAST SIGNIFICANT BYTE
04481-A-003
t1
Figure 3. Serial Write Timing
CS
t1
t13
t9
SCLK
0
0
A5
A4
A3
A2
A1
A0
DOUT
DB7
COMMAND BYTE
t12
t11
t11
DB0
MOST SIGNIFICANT BYTE
Figure 4. Serial Read Timing
Rev. A | Page 5 of 56
DB7
DB0
LEAST SIGNIFICANT BYTE
04481-A-004
DIN
t10
ADE7763
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 3.
Parameter
AVDD to AGND
DVDD to DGND
DVDD to AVDD
Analog Input Voltage to AGND
V1P, V1N, V2P, and V2N
Reference Input Voltage to AGND
Digital Input Voltage to DGND
Digital Output Voltage to DGND
Operating Temperature Range
Industrial
Storage Temperature Range
Junction Temperature
20-Lead SSOP, Power Dissipation
θJA Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 s)
Infrared (15 s)
Rating
–0.3 V to +7 V
–0.3 V to +7 V
–0.3 V to +0.3 V
–6 V to +6 V
–0.3 V to AVDD + 0.3 V
–0.3 V to DVDD + 0.3 V
–0.3 V to DVDD + 0.3 V
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only, and functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
–40°C to +85°C
–65°C to +150°C
150°C
450 mW
112°C/W
215°C
220°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. A | Page 6 of 56
ADE7763
TERMINOLOGY
Measurement Error
The error associated with the energy measurement made by the
ADE7763 is defined by the following formula:
Percent Error =
⎛ Energy Register ADE7763 − True Energy ⎞
⎜
⎟ × 100%
⎜
⎟
True Energy
⎝
⎠
Phase Error between Channels
The digital integrator and the high-pass filter (HPF) in Channel 1
have a nonideal phase response. To offset this phase response
and equalize the phase response between channels, two phasecorrection networks are placed in Channel 1: one for the digital
integrator and the other for the HPF. The phase correction
networks correct the phase response of the corresponding
component and ensure a phase match between Channel 1
(current) and Channel 2 (voltage) to within ±0.1° over a range
of 45 Hz to 65 Hz with the digital integrator off. With the digital
integrator on, the phase is corrected to within ±0.4° over a
range of 45 Hz to 65 Hz.
Power Supply Rejection
This quantifies the ADE7763 measurement error as a percentage
of the reading when the power supplies are varied. For the ac
PSR measurement, a reading at nominal supplies (5 V) is taken.
A second reading is obtained with the same input signal levels
when an ac (175 mV rms/120 Hz) signal is introduced to the
supplies. Any error introduced by this ac signal is expressed
as a percentage of the reading—see the Measurement
Error definition.
For the dc PSR measurement, a reading at nominal supplies
(5 V) is taken. A second reading is obtained with the same input
signal levels when the supplies are varied ±5%. Any error
introduced is again expressed as a percentage of the reading.
ADC Offset Error
The dc offset associated with the analog inputs to the ADCs. It
means that with the analog inputs connected to AGND, the
ADCs still see a dc analog input signal. The magnitude of the
offset depends on the gain and input range selection—see the
Typical Performance Characteristics section. However, when
HPF1 is switched on, the offset is removed from Channel 1
(current) and the power calculation is not affected by this offset.
The offsets can be removed by performing an offset calibration—
see the Analog Inputs section.
Gain Error
The difference between the measured ADC output code (minus
the offset) and the ideal output code—see the Channel 1 ADC
and Channel 2 ADC sections. It is measured for each of the
input ranges on Channel 1 (0.5 V, 0.25 V, and 0.125 V). The
difference is expressed as a percentage of the ideal code.
Rev. A | Page 7 of 56
ADE7763
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
RESET 1
20 DIN
DVDD 2
19 DOUT
AVDD 3
18 SCLK
V1P 4
V1N 5
ADE7763
17 CS
16 CLKOUT
TOP VIEW
V2N 6 (Not to Scale) 15 CLKIN
14 IRQ
13 SAG
REFIN/OUT 9
12 ZX
DGND 10
11 CF
04481-A-005
V2P 7
AGND 8
Figure 5. Pin Configuration (SSOP Package)
Table 4. Pin Function Descriptions
Pin No.
1
Mnemonic
RESET
2
DVDD
3
AVDD
4, 5
V1P, V1N
6, 7
V2N, V2P
8
AGND
9
REFIN/OUT
10
DGND
11
CF
12
ZX
13
SAG
14
IRQ
Description
Reset Pin for the ADE7763. A logic low on this pin holds the ADCs and digital circuitry (including the serial
interface) in a reset condition.
Digital Power Supply. This pin provides the supply voltage for the digital circuitry. The supply voltage
should be maintained at 5 V ± 5% for specified operation. This pin should be decoupled to DGND with a
10 µF capacitor in parallel with a ceramic 100 nF capacitor.
Analog Power Supply. This pin provides the supply voltage for the analog circuitry. The supply should be
maintained at 5 V ± 5% for specified operation. Minimize power supply ripple and noise at this pin by using
proper decoupling. The typical performance graphs show the power supply rejection performance. This
pin should be decoupled to AGND with a 10 µF capacitor in parallel with a ceramic 100 nF capacitor.
Analog Inputs for Channel 1. This channel is intended for use with a di/dt current transducer, i.e., a
Rogowski coil or another current sensor such as a shunt or current transformer (CT). These inputs are fully
differential voltage inputs with maximum differential input signal levels of ±0.5 V, ±0.25 V, and ±0.125 V,
depending on the full-scale selection—see the Analog Inputs section. Channel 1 also has a PGA with gain
selections of 1, 2, 4, 8, or 16. The maximum signal level at these pins with respect to AGND is ±0.5 V. Both
inputs have internal ESD protection circuitry and can sustain an overvoltage of ±6 V without risk of
permanent damage.
Analog Inputs for Channel 2. This channel is intended for use with the voltage transducer. These inputs are
fully differential voltage inputs with a maximum differential signal level of ±0.5 V. Channel 2 also has a PGA
with gain selections of 1, 2, 4, 8, or 16. The maximum signal level at these pins with respect to AGND is
±0.5 V. Both inputs have internal ESD protection circuitry and can sustain an overvoltage of ±6 V without
risk of permanent damage.
Analog Ground Reference. This pin provides the ground reference for the analog circuitry, i.e., ADCs and
reference. This pin should be tied to the analog ground plane or to the quietest ground reference in the
system. Use this quiet ground reference for all analog circuitry, such as antialiasing filters and current and
voltage transducers. To minimize ground noise around the ADE7763, connect the quiet ground plane
to the digital ground plane at only one point. It is acceptable to place the entire device on the analog
ground plane.
Access to the On-Chip Voltage Reference. The on-chip reference has a nominal value of 2.4 V ± 8% and a
typical temperature coefficient of 30 ppm/°C. An external reference source can also be connected at this
pin. In either case, this pin should be decoupled to AGND with a 1 µF ceramic capacitor.
Digital Ground Reference. This pin provides the ground reference for the digital circuitry, i.e., multiplier,
filters, and digital-to-frequency converter. Because the digital return currents in the ADE7763 are small, it is
acceptable to connect this pin to the analog ground plane of the system. However, high bus capacitance
on the DOUT pin could result in noisy digital current, which could affect performance.
Calibration Frequency Logic Output. The CF logic output gives active power information. This output is
intended to be used for operational and calibration purposes. The full-scale output frequency can be
adjusted by writing to the CFDEN and CFNUM registers—see the Energy-to-Frequency Conversion section.
Voltage Waveform (Channel 2) Zero-Crossing Output. This output toggles logic high and logic low at the
zero crossing of the differential signal on Channel 2—see the Zero-Crossing Detection section.
This open-drain logic output goes active low when either no zero crossings are detected or a low voltage
threshold (Channel 2) is crossed for a specified duration—see the Line Voltage Sag Detection section.
Interrupt Request Output. This is an active low, open-drain logic output. Maskable interrupts include active
energy register rollover, active energy register at half level, and arrivals of new waveform samples—see the
Interrupts section.
Rev. A | Page 8 of 56
ADE7763
Pin No.
15
Mnemonic
CLKIN
16
CLKOUT
17
CS
18
SCLK
19
DOUT
20
DIN
Description
Master Clock for ADCs and Digital Signal Processing. An external clock can be provided at this logic input.
Alternatively, a parallel resonant AT crystal can be connected across CLKIN and CLKOUT to provide a clock
source for the ADE7763. The clock frequency for specified operation is 3.579545 MHz. Ceramic load
capacitors between 22 pF and 33 pF should be used with the gate oscillator circuit. Refer to the crystal
manufacturer’s data sheet for load capacitance requirements.
A crystal can be connected across this pin and CLKIN, as described for Pin 15, to provide a clock source for
the ADE7763. The CLKOUT pin can drive one CMOS load when either an external clock is supplied at CLKIN
or a crystal is being used.
Chip Select. Part of the 4-wire SPI serial interface. This active low logic input allows the ADE7763 to share
the serial bus with several other devices—see the Serial Interface section.
Serial Clock Input for the Synchronous Serial Interface. All serial data transfers are synchronized to this
clock—see the Serial Interface section. The SCLK has a Schmitt-trigger input for use with a clock source
that has a slow edge transition time, such as an opto-isolator output.
Data Output for the Serial Interface. Data is shifted out at this pin upon the rising edge of SCLK. This logic
output is normally in a high impedance state, unless it is driving data onto the serial data bus—see the
Serial Interface section.
Data Input for the Serial Interface. Data is shifted in at this pin upon the falling edge of SCLK—see the
Serial Interface section.
Rev. A | Page 9 of 56
ADE7763
TYPICAL PERFORMANCE CHARACTERISTICS
1.0
0.4
GAIN = 1
INTEGRATOR OFF
INTERNAL REFERENCE
0.3
0.8
0.6
0.2
+25°C, PF = 1
0.4
ERROR (%)
0
–40°C, PF = 0.5
–0.1
–0.2
+25°C, PF = 0.5
–0.3
0
–0.2
+85°C, PF = 1
–0.6
1
10
100
FULL-SCALE CURRENT (%)
–1.0
0.1
04481-A-006
–0.6
0.1
10
100
Figure 6. Active Energy Error as a Percentage of Reading (Gain = 1)
over Power Factor with Internal Reference and Integrator Off
Figure 9. Active Energy Error as a Percentage of Reading (Gain = 8)
over Temperature with External Reference and Integrator Off
1.0
1.0
0.6
GAIN = 8
INTEGRATOR OFF
INTERNAL REFERENCE
0.8
0.6
0.4
GAIN = 8
INTEGRATOR OFF
EXTERNAL REFERENCE
0.4
+85°C, PF = 1
ERROR (%)
0.2
0
+25°C, PF = 1
–0.2
+25°C, PF = 1
0
–0.2
–40°C, PF = 0.5
–0.4
–40°C, PF = 1
–0.6
–0.6
–0.8
–0.8
1
10
100
FULL-SCALE CURRENT (%)
–1.0
0.1
04481-A-007
–1.0
0.1
1
10
100
FULL-SCALE CURRENT (%)
Figure 7. Active Energy as a Percentage of Reading (Gain = 8)
over Temperature with Internal Reference and Integrator Off
Figure 10. Active Energy Error as a Percentage of Reading (Gain = 8)
over Power Factor with External Reference and Integrator Off
1.0
0.6
+25°C, PF = 0.5
+85°C, PF = 0.5
–0.4
0.8
0.2
04481-A-010
0.8
ERROR (%)
1
FULL-SCALE CURRENT (%)
04481-A-009
–0.8
–0.5
0.5
GAIN = 8
INTEGRATOR OFF
INTERNAL REFERENCE
0.3
0.2
ERROR (%)
+85°C, PF = 0.5
0.2
0
–0.2
+25°C, PF = 1
+25°C, PF = 0.5
–0.4
5.25V
0.1
0
5.00V
–0.1
–0.2
–0.6
–40°C, PF = 0.5
–0.3
–0.8
4.75V
–0.4
1
10
100
FULL-SCALE CURRENT (%)
04481-A-008
–1.0
0.1
GAIN = 8
INTEGRATOR OFF
INTERNAL REFERENCE
0.4
0.4
ERROR (%)
–40°C, PF = 1
–0.4
+85°C, PF = 0.5
–0.4
+25°C, PF = 1
0.2
Figure 8. Active Energy Error as a Percentage of Reading (Gain = 8)
over Power Factor with Internal Reference and Integrator Off
–0.5
0.1
1
10
100
FULL-SCALE CURRENT (%)
Figure 11. Active Energy Error as a Percentage of Reading (Gain = 8)
over Power Supply with Internal Reference and Integrator Off
Rev. A | Page 10 of 56
04481-A-080
ERROR (%)
0.1
GAIN = 8
INTEGRATOR OFF
EXTERNAL REFERENCE
ADE7763
1.2
1.0
GAIN = 8
INTEGRATOR OFF
INTERNAL REFERENCE
1.0
0.8
0.6
0.8
0.4
0.6
PF = 0.5
ERROR (%)
0.4
0.2
PF = 1
0
+85°C, PF = 0.5
0.2
0
+25°C, PF = 0.5
+25°C, PF = 1
–0.2
–0.4
–0.2
–40°C, PF = 0.5
–0.6
–0.4
–0.8
45
47
49
51
53
55
57
59
61
63
65
FREQUENCY (Hz)
–1.0
0.1
04481-A-012
–0.6
1
10
100
FULL-SCALE CURRENT (%)
Figure 12. Active Energy Error as a Percentage of Reading (Gain = 8)
over Frequency with Internal Reference and Integrator Off
04481-A-016
ERROR (%)
GAIN = 8
INTEGRATOR ON
INTERNAL REFERENCE
Figure 15. Active Energy Error as a Percentage of Reading (Gain = 8)
over Power Factor with Internal Reference and Integrator On
1.0
1.0
GAIN = 8
INTEGRATOR OFF
INTERNAL REFERENCE
0.8
0.6
0.8
GAIN = 8
INTEGRATOR ON
INTERNAL REFERENCE
0.6
0.4
0.4
0
PF = 0.5
–0.2
0.2
0
–0.4
–0.6
–0.6
–0.8
–0.8
–1.0
0.1
1
10
100
FULL-SCALE CURRENT (%)
+25°C, PF = 1
–0.2
–0.4
–40°C, PF = 1
–1.0
0.1
1
10
100
FULL-SCALE CURRENT (%)
Figure 13. IRMS Error as a Percentage of Reading (Gain = 8)
with Internal Reference and Integrator Off
04481-A-015
ERROR (%)
PF = 1
04481-A-013
ERROR (%)
+85°C, PF = 1
0.2
Figure 16. Active Energy Error as a Percentage of Reading (Gain = 8)
over Temperature with External Reference and Integrator On
0.5
3.0
GAIN = 1
EXTERNAL REFERENCE
0.4
GAIN = 8
INTEGRATOR ON
INTERNAL REFERENCE
2.5
0.3
2.0
0.2
1.5
0.1
1.0
0.5
–0.2
–0.5
–0.3
–1.0
–0.4
–1.5
–0.5
1
10
100
FULL-SCALE VOLTAGE (%)
PF = 1
0
–2.0
45
47
49
51
53
55
57
59
61
63
65
FREQUENCY (Hz)
Figure 17. Active Energy Error as a Percentage of Reading (Gain = 8)
over Frequency with Internal Reference and Integrator On
Figure 14. VRMS Error as a Percentage of Reading (Gain = 1)
with External Reference
Rev. A | Page 11 of 56
04481-A-017
ERROR (%)
0
–0.1
04481-A-020
ERROR (%)
PF = 0.5
ADE7763
0.5
16
GAIN = 8
INTEGRATOR ON
INTERNAL REFERENCE
0.4
0.3
14
5.25V
12
10
0.1
HITS
ERROR (%)
0.2
5.00V
0
8
–0.1
6
–0.2
4.75V
4
–0.3
1
10
0
–15
04481-A-081
–0.5
0.1
100
FULL-SCALE CURRENT (%)
–10
–5
0
5
10
15
04481-A-021
2
–0.4
20
CH1 OFFSET (0p5V_1X) (mV)
Figure 18. Active Energy Error as a Percentage of Reading (Gain = 8)
over Power Supply with Internal Reference and Integrator On
Figure 20. Channel 1 Offset (Gain = 1)
0.5
GAIN = 8
INTEGRATOR ON
INTERNAL REFERENCE
0.4
0.3
ERROR (%)
0.2
0.1
PF = 0.5
0
–0.1
PF = 1
–0.2
–0.3
–0.5
0.1
1
10
04481-A-019
–0.4
100
FULL-SCALE CURRENT (%)
Figure 19. IRMS Error as a Percentage of Reading (Gain = 8)
with Internal Reference and Integrator On
VDD
VDD
100nF
di/dt CURRENT
SENSOR
100Ω 1kΩ
33nF
33nF
100Ω
1kΩ
33nF
33nF
100nF
AVDD DVDD RESET
DIN
V1P
DOUT
V1N
SCLK
U1
ADE7763
10µF
CURRENT
TRANSFORMER
1kΩ
600kΩ
110V
1kΩ
CLKIN
V2P
SAG
Y1
3.58MHz
22pF
REFIN/OUT
CF
U1
ADE7763
TO SPI BUS
(USED ONLY FOR
CALIBRATION)
CS
V2N
1kΩ
22pF
33nF
CLKIN
600kΩ
V2P
110V
1kΩ
Y1
3.58MHz
22pF
22pF
IRQ
33nF
SAG
NOT CONNECTED
NOT CONNECTED
ZX
10µF
U3
AGND DGND
TO
FREQUENCY
COUNTER
CHANNEL 1 GAIN = 8
CHANNEL 2 GAIN = 1
PS2501-1
04481-A-022
100nF
V1N
SCLK
10µF
CLKOUT
ZX
10µF
AVDD DVDD RESET
DIN
V1P
DOUT
1kΩ
IRQ
33nF
100nF
RB
33nF
CLKOUT
33nF
33nF
TO SPI BUS
(USED ONLY FOR
CALIBRATION)
CS
V2N
1kΩ
100nF
10µF
I
100nF
REFIN/OUT
CF
U3
AGND DGND
CT TURN RATIO = 1800:1
CHANNEL 2 GAIN = 1
GAIN 1 (CH1) RB
10Ω
1
1.21Ω
8
TO
FREQUENCY
COUNTER
PS2501-1
Figure 22. Test Circuit for Performance Curves with Integrator Off
Figure 21. Test Circuit for Performance Curves with Integrator On
Rev. A | Page 12 of 56
04481-A-023
10µF
I
ADE7763
THEORY OF OPERATION
ANALOG INPUTS
Table 5. Maximum Input Signal Levels for Channel 1
The ADE7763 has two fully differential voltage input channels.
The maximum differential input voltage for input pairs V1P/V1N
and V2P/V2N is ±0.5 V. In addition, the maximum signal level
on analog inputs for V1P/V1N and V2P/V2N is ±0.5 V with
respect to AGND.
Max Signal
Channel 1
0.5 V
0.25 V
0.125 V
0.0625 V
0.0313 V
0.0156 V
0.00781 V
7
6
5
GAIN[7:0]
4
3
2
0
0
0
0
0
0
1
0
0
0
GAIN REGISTER*
CHANNEL 1 AND CHANNEL 2 PGA CONTROL
7
6
5
4
3
2
1
0
0
0
0
0
0
0
PGA 2 GAIN SELECT
000 = × 1
001 = × 2
010 = × 4
011 = × 8
100 = × 16
GAIN (K)
SELECTION
* REGISTER CONTENTS
SHOW POWER-ON DEFAULTS
V1P
0
0
ADDR:
0x0A
PGA 1 GAIN SELECT
000 = × 1
001 = × 2
010 = × 4
011 = × 8
100 = × 16
CHANNEL 1 FULL-SCALE SELECT
00 = 0.5V
01 = 0.25V
10 = 0.125V
04481-A-025
Each analog input channel has a programmable gain amplifier
(PGA) with possible gain selections of 1, 2, 4, 8, and 16. The
gain selections are made by writing to the gain register—see
Figure 24. Bits 0 to 2 select the gain for the PGA in Channel 1;
the gain selection for the PGA in Channel 2 is made via Bits 5
to 7. Figure 23 shows how a gain selection for Channel 1 is
made using the gain register.
ADC Input Range Selection
0.5 V
0.25 V
0.125 V
Gain = 1
−
−
Gain = 2
Gain = 1
−
Gain = 4
Gain = 2
Gain = 1
Gain = 8
Gain = 4
Gain = 2
Gain = 16
Gain = 8
Gain = 4
−
Gain = 16
Gain = 8
−
−
Gain = 16
Figure 24. Analog Gain Register
VIN
K × VIN
V1N
+
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
OFFSET ADJUST
(±50mV)
CH1OS[7:0]
BITS 0 to 5: SIGN MAGNITUDE CODED OFFSET CORRECTION
BIT 6: NOT USED
BIT 7: DIGITAL INTEGRATOR (ON = 1, OFF = 0; DEFAULT OFF)
04481-A-024
7
Figure 23. PGA in Channel 1
In addition to the PGA, Channel 1 also has a full-scale input
range selection for the ADC. The ADC analog input range
selection is also made using the gain register—see Figure 24. As
previously mentioned, the maximum differential input voltage
is 0.5 V. However, by using Bits 3 and 4 in the gain register, the
maximum ADC input voltage can be set to 0.5 V, 0.25 V, or
0.125 V. This is achieved by adjusting the ADC reference—see
the Reference Circuit section. Table 5 summarizes the
maximum differential input signal level on Channel 1 for the
various ADC range and gain selections.
It is also possible to adjust offset errors on Channel 1 and
Channel 2 by writing to the offset correction registers (CH1OS
and CH2OS, respectively). These registers allow channel offsets
in the range ±20 mV to ±50 mV (depending on the gain setting)
to be removed. Note that it is not necessary to perform an offset
correction in an energy measurement application if HPF in
Channel 1 is switched on. Figure 25 shows the effect of offsets
on the real power calculation. As seen from Figure 25, an offset
on Channel 1 and Channel 2 contributes a dc component after
multiplication. Because this dc component is extracted by LPF2
to generate the active (real) power information, the offsets
contribute an error to the active power calculation. This problem
is easily avoided by enabling HPF in Channel 1. By removing
the offset from at least one channel, no error component is
generated at dc by the multiplication. Error terms at cos(ωt) are
removed by LPF2 and by integration of the active power signal
in the active energy register (AENERGY[23:0])—see the Energy
Calculation section.
Rev. A | Page 13 of 56
ADE7763
The current and voltage rms offsets can be adjusted with the
IRMSOS and VRMSOS registers—see the Channel 1 RMS Offset
Compensation and Channel 2 RMS Offset Compensation
sections.
DC COMPONENT (INCLUDING ERROR TERM)
IS EXTRACTED BY THE LPF FOR REAL
POWER CALCULATION
VOS × IOS
V×I
2
di/dt CURRENT SENSOR AND
DIGITAL INTEGRATOR
IOS × V
A di/dt sensor detects changes in magnetic field caused by ac
current. Figure 27 shows the principle of a di/dt current sensor.
04481-A-026
VOS × I
ω
0
2ω
FREQUENCY (RAD/S)
Figure 25. Effect of Channel Offsets on the Real Power Calculation
Table 6. Offset Correction Range—Channels 1 and 2
Correctable Span
±50 mV
±37 mV
±30 mV
±26 mV
±24 mV
LSB Size
1.61 mV/LSB
1.19 mV/LSB
0.97 mV/LSB
0.84 mV/LSB
0.77 mV/LSB
+ EMF (ELECTROMOTIVE FORCE)
– INDUCED BY CHANGES IN
MAGNETIC FLUX DENSITY (di/dt)
Figure 27. Principle of a di/dt Current Sensor
The flux density of a magnetic field induced by a current is
directly proportional to the magnitude of the current. Changes
in the magnetic flux density passing through a conductor loop
generate an electromotive force (EMF) between the two ends of
the loop. The EMF is a voltage signal that is proportional to the
di/dt of the current. The voltage output from the di/dt current
sensor is determined by the mutual inductance between the
current-carrying conductor and the di/dt sensor. The current
signal must be recovered from the di/dt signal before it can be
used. An integrator is therefore necessary to restore the signal to
its original form. The ADE7763 has a built-in digital integrator
to recover the current signal from the di/dt sensor. The digital
integrator on Channel 1 is switched off by default when the
ADE7763 is powered up. Setting the MSB of CH1OS register
turns on the integrator. Figure 28, Figure 29, Figure 30, and
Figure 31 show the magnitude and phase response of the digital
integrator.
10
CH1OS[5:0]
0x1F
01,1111b
SIGN + 5 BITS
0
GAIN (dB)
–10
0x00
+50mV
OFFSET
ADJUST
0x3F
11,1111b SIGN + 5 BITS
–20
–30
–40
Figure 26. Channel 1 Offset Correction Range (Gain = 1)
–50
102
103
FREQUENCY (Hz)
Figure 28. Combined Gain Response of the
Digital Integrator and Phase Compensator
Rev. A | Page 14 of 56
04481-A-029
0mV
–50mV
04481-A-027
Gain
1
2
4
8
16
MAGNETIC FIELD CREATED BY CURRENT
(DIRECTLY PROPORTIONAL TO CURRENT)
04481-A-028
The contents of the offset correction registers are 6-bit, sign and
magnitude coded. The weight of the LSB depends on the gain
setting, i.e., 1, 2, 4, 8, or 16. Table 6 shows the correctable offset
span for each of the gain settings and the LSB weight (mV) for
the offset correction registers. The maximum value that can be
written to the offset correction registers is ±31d—see Figure 26.
Figure 26 shows the relationship between the offset correction
register contents and the offset (mV) on the analog inputs for a
gain of 1. To perform an offset adjustment, connect the analog
inputs to AGND; there should be no signal on either Channel 1
or Channel 2. A read from Channel 1 or Channel 2 using the
waveform register indicates the offset in the channel. This offset
can be canceled by writing an equal and opposite offset value to
the Channel 1 offset register, or an equal value to the Channel 2
offset register. The offset correction can be confirmed by
performing another read. Note that when adjusting the offset of
Channel 1, the digital integrator and the HPF should be
disabled.
ADE7763
–88.0
Note that the integrator has a –20 dB/dec attenuation and
approximately a –90° phase shift. When combined with a di/dt
sensor, the resulting magnitude and phase response should be a
flat gain over the frequency band of interest. The di/dt sensor
has a 20 dB/dec gain. It also generates significant high
frequency noise, necessitating a more effective antialiasing filter
to avoid noise due to aliasing—see the Antialias Filter section.
PHASE (Degrees)
–88.5
–89.0
–89.5
When the digital integrator is switched off, the ADE7763 can be
used directly with a conventional current sensor such as a current
transformer (CT) or with a low resistance current shunt.
–90.0
102
04481-A-030
–90.5
103
FREQUENCY (Hz)
Figure 29. Combined Phase Response of the
Digital Integrator and Phase Compensator
–1.0
–1.5
ZERO-CROSSING DETECTION
The ADE7763 has a zero-crossing detection circuit on Channel 2.
This zero crossing is used to produce an external zero-crossing
signal (ZX), which is used in the calibration mode (see the
Calibrating an Energy Meter section). This signal is also used to
initiate a temperature measurement (see the Temperature
Measurement section).
Figure 32 shows how the zero-crossing signal is generated from
the output of LPF1.
–2.0
GAIN (dB)
–2.5
×1, ×2, ×1,
×8, ×16
–3.0
V2P
REFERENCE
{GAIN[7:5]}
–3.5
PGA2
V2
–4.0
ADC 2
1
–63% TO +63% FS
TO
MULTIPLIER
V2N
–4.5
ZERO
CROSSING
–5.0
ZX
LPF1
f–3dB = 140Hz
–6.0
40
45
50
55
60
65
70
FREQUENCY (Hz)
04481-A-031
–5.5
2.32° @ 60Hz
1.0
0.93
ZX
V2
LPF1
–89.70
04481-A-033
Figure 30. Combined Gain Response of the
Digital Integrator and Phase Compensator (40 Hz to 70 Hz)
Figure 32. Zero-Crossing Detection on Channel 2
–89.75
The ZX signal goes logic high upon a positive-going zero
crossing and logic low upon a negative-going zero crossing on
Channel 2. The ZX signal is generated from the output of LPF1.
LPF1 has a single pole at 140 Hz (@ CLKIN = 3.579545 MHz).
As a result, there is a phase lag between the analog input signal
V2 and the output of LPF1. The phase response of this filter is
shown in the Channel 2 Sampling section. The phase lag response
of LPF1 results in a time delay of approximately 1.14 ms
(@ 60 Hz) between the zero crossing on the analog inputs of
Channel 2 and the rising or falling edge of ZX.
–89.85
–89.90
–89.95
–90.00
–90.05
–90.10
40
45
50
55
60
65
70
FREQUENCY (Hz)
04481-A-032
PHASE (Degrees)
–89.80
Figure 31. Combined Phase Response of the
Digital Integrator and Phase Compensator (40 Hz to 70 Hz)
Rev. A | Page 15 of 56
ADE7763
Zero-crossing detection also drives the ZX flag in the interrupt
status register. An active low in the IRQ output appears if the
corresponding bit in the interrupt enable register is set to Logic 1.
The flag in the interrupt status register and the IRQ output are
set to their default values when reset (RSTSTATUS) is read in
the interrupt status register.
Zero-Crossing Timeout
Zero-crossing detection has an associated timeout register,
ZXTOUT. This unsigned, 12-bit register is decremented (1 LSB)
every 128/CLKIN seconds. The register is reset to its userprogrammed, full-scale value when a zero crossing on Channel 2
is detected. The default power-on value in this register is 0xFFF.
If the internal register decrements to 0 before a zero crossing is
detected and the DISSAG bit in the mode register is Logic 0, the
SAG pin will go active low. The absence of a zero crossing is
also indicated on the IRQ pin if the ZXTO enable bit in the
interrupt enable register is set to Logic 1. Irrespective of the
enable bit setting, the ZXTO flag in the interrupt status register
is always set when the internal ZXTOUT register is
decremented to 0—see the Interrupts section.
The ZXOUT register, Address 0x1D, can be written to and read
from by the user—see the Serial Interface section. The
resolution of the register is 128/CLKIN seconds per LSB;
therefore, the maximum delay for an interrupt is 0.15 seconds
(128/CLKIN × 212).
PERIOD MEASUREMENT
The ADE7763 provides the period measurement of the line.
The PERIOD register is an unsigned, 16-bit register that is
updated every period and always has an MSB of zero.
When CLKIN = 3.579545 MHz, the resolution of this register is
2.2 ms/LSB, which represents 0.013% when the line frequency is
60 Hz. When the line frequency is 60 Hz, the value of the
period register is approximately 7457d. The length of the register
enables the measurement of line frequencies as low as 13.9 Hz.
The period register is stable at ±1 LSB when the line is established
and the measurement does not change. This filter is associated
with a settling time of 1.8 seconds before the measurement is
stable. See the Calibrating an Energy Meter section for more on
the period register.
POWER SUPPLY MONITOR
The ADE7763 contains an on-chip power supply monitor. The
analog supply (AVDD) is continuously monitored. If the supply
is less than 4 V ± 5%, the ADE7763 will go into an inactive state
and no energy will accumulate. This is useful to ensure correct
device operation during power-up and power-down stages. In
addition, built-in hysteresis and filtering help prevent false
triggering due to noisy supplies.
AVDD
5V
4V
Figure 33 shows the zero-crossing timeout detection when the
line voltage stays at a fixed dc level for more than CLKIN/128 ×
ZXTOUT seconds.
0V
TIME
12-BIT INTERNAL
REGISTER VALUE
ZXTOUT
ACTIVE
INACTIVE
04481-A-035
ADE7763
POWER-ON
INACTIVE INACTIVE
STATE
SAG
CHANNEL 2
ZXTO
DETECTION
BIT
Figure 33. Zero-Crossing Timeout Detection
04481-A-034
Figure 34. On-Chip Power Supply Monitor
As seen in Figure 34, the trigger level is nominally set at 4 V.
The tolerance on this trigger level is about ±5%. The SAG pin
can also be used as a power supply monitor input to the MCU.
The SAG pin goes logic low when the ADE7763 is in its inactive
state. The power supply and decoupling for the part should be
such that the ripple at AVDD does not exceed 5 V ± 5%, as
specified for normal operation.
Rev. A | Page 16 of 56
ADE7763
LINE VOLTAGE SAG DETECTION
PEAK DETECTION
In addition to detecting the loss of the line voltage when there
are no zero crossings on the voltage channel, the ADE7763 can
also be programmed to detect when the absolute value of the line
voltage drops below a peak value for a specified number of line
cycles. This condition is illustrated in Figure 35.
The ADE7763 can also be programmed to detect when the
absolute value of the voltage or current channel exceeds a
specified peak value. Figure 36 illustrates the behavior of the
peak detection for the voltage channel.
Both Channel 1 and Channel 2 are monitored at the same time.
V2
CHANNEL 2
FULL SCALE
VPKLVL[7:0]
SAGLVL[7:0]
PKV RESET LOW
WHEN RSTSTATUS
REGISTER IS READ
SAG RESET HIGH
WHEN CHANNEL 2
EXCEEDS SAGLVL[7:0]
SAGCYC[7:0] = 0x04
3 LINE CYCLES
PKV INTERRUPT
FLAG (BIT 8 OF
STATUS REGISTER)
04481-A-037
04481-A-036
SAG
READ RSTSTATUS
REGISTER
Figure 35. Sag Detection
In Figure 35 the line voltage falls below a threshold that
has been set in the sag level register (SAGLVL[7:0]) for three
line cycles. The quantities 0 and 1 are not valid for the SAGCYC
register, and the contents represent one more than the desired
number of full line cycles. For example, if the DISSAG bit in the
mode register is Logic 0 and the sag cycle register
(SAGCYC[7:0]) contains 0x04, the SAG pin goes active low at
the end of the third line cycle for which the line voltage
(Channel 2 signal) falls below the threshold. As is the case when
zero crossings are no longer detected, the sag event is also
recorded by setting the SAG flag in the interrupt status register.
If the SAG enable bit is set to Logic 1, the IRQ logic output will
go active low—see the Interrupts section. The SAG pin goes
logic high again when the absolute value of the signal on Channel
2 exceeds the level set in the sag level register. This is shown in
Figure 35 when the SAG pin goes high again during the fifth line
cycle from the time when the signal on Channel 2 first dropped
below the threshold level.
Sag Level Set
The contents of the sag level register (1 byte) are compared to
the absolute value of the most significant byte output from
LPF1 after it is shifted left by one bit. For example, the nominal
maximum code from LPF1 with a full-scale signal on Channel 2
is 0x2518—see the Channel 2 Sampling section. Shifting one bit
left gives 0x4A30. Therefore, writing 0x4A to the SAG level
register puts the sag detection level at full scale. Writing 0x00 or
0x01 puts the sag detection level at 0. The SAG level register is
compared to the most significant byte of a waveform sample
after the shift left, and detection occurs when the contents of
the sag level register are greater.
Figure 36. Peak Level Detection
Figure 36 shows a line voltage exceeding a threshold that has
been set in the voltage peak register (VPKLVL[7:0]). The
voltage peak event is recorded by setting the PKV flag in the
interrupt status register. If the PKV enable bit is set to Logic 1 in
the interrupt mask register, the IRQ logic output will go active
low. Similarly, the current peak event is recorded by setting the
PKI flag in the interrupt status register—see the Interrupts
section.
Peak Level Set
The contents of the VPKLVL and IPKLVL registers are
compared to the absolute value of Channel 1 and Channel 2,
respectively, after they are multiplied by 2. For example, the
nominal maximum code from the Channel 1 ADC with a fullscale signal is 0x2851EC—see the Channel 1 Sampling section.
Multiplying by 2 gives 0x50A3D8. Therefore, writing 0x50 to
the IPKLVL register, for example, puts the Channel 1 peak
detection level at full scale and sets the current peak detection
to its least sensitive value. Writing 0x00 puts the Channel 1
detection level at 0. Peak level detection is done by comparing
the contents of the IPKLVL register to the incoming Channel 1
sample. The IRQ pin indicates that the peak level is exceeded if
the PKI or PKV bits are set in the interrupt enable register
(IRQEN [15:0]) at Address 0x0A.
Peak Level Record
The ADE7763 records the maximum absolute value reached by
Channel 1 and Channel 2 in two different registers—IPEAK
and VPEAK, respectively. VPEAK and IPEAK are 24-bit,
unsigned registers. These registers are updated each time the
absolute value of the waveform sample from the corresponding
channel is above the value stored in the VPEAK or IPEAK
register. The contents of the VPEAK register correspond to two
Rev. A | Page 17 of 56
ADE7763
Using Interrupts with an MCU
times the maximum absolute value observed on the Channel 2
input. The contents of IPEAK represent the maximum absolute
value observed on the Channel 1 input. Reading the RSTVPEAK
and RSTIPEAK registers clears their respective contents after
the read operation.
Figure 38 shows a timing diagram with a suggested implementation of ADE7763 interrupt management using an MCU.
At time t1, the IRQ line goes active low, indicating that one or
more interrupt events have occurred. Tie the IRQ logic output to
a negative edge-triggered external interrupt on the MCU.
Configure the MCU to start executing its interrupt service
routine (ISR) when a negative edge is detected on the IRQ line.
After entering the ISR, disable all interrupts by using the global
interrupt enable bit. At this point, the MCU IRQ external
interrupt flag can be cleared to capture interrupt events that
occur during the current ISR. When the MCU interrupt flag is
cleared, a read from the status register with reset is carried out.
This causes the IRQ line to reset to logic high (t2)—see the
Interrupt Timing section. The status register contents are used
to determine the source of the interrupt(s) and, therefore, the
appropriate action to be taken. If a subsequent interrupt event
occurs during the ISR, that event will be recorded by the MCU
external interrupt flag being set again (t3). Upon the completion
of the ISR, the global interrupt mask is cleared (same
instruction cycle) and the external interrupt flag causes the
MCU to jump to its ISR again. This ensures that the MCU does
not miss any external interrupts.
INTERRUPTS
Interrupts are managed through the interrupt status register
(STATUS[15:0]) and the interrupt enable register
(IRQEN[15:0]). When an interrupt event occurs, the
corresponding flag in the status register is set to Logic 1—see
the Interrupt Status Register section. If the enable bit for this
interrupt in the interrupt enable register is Logic 1, the IRQ
logic output will go active low. The flag bits in the status register
are set irrespective of the state of the enable bits.
To determine the source of the interrupt, the system master
(MCU) should perform a read from the status register with
reset (RSTSTATUS[15:0]). This is achieved by carrying out a
read from Address 0Ch. The IRQ output goes logic high after
the completion of the interrupt status register read command—
see the Interrupt Timing section. When carrying out a read
with reset, the ADE7763 is designed to ensure that no interrupt
events are missed. If an interrupt event occurs as the status
register is being read, the event will not be lost and the IRQ
logic output will be guaranteed to go high for the duration of
the interrupt status register data transfer before going logic low
again to indicate the pending interrupt. See the next section for
a more detailed description.
t1
t2
MCU
INTERRUPT
FLAG SET
t3
MCU
PROGRAM
SEQUENCE
JUMP
TO
ISR
GLOBAL
INTERRUPT
MASK SET
CLEAR MCU
INTERRUPT
FLAG
READ
STATUS WITH
RESET (0x05)
ISR ACTION
(BASED ON STATUS CONTENTS)
ISR RETURN
GLOBAL INTERRUPT
MASK RESET
04481-A-038
IRQ
JUMP
TO
ISR
Figure 37. Interrupt Management
CS
t1
t9
SCLK
DIN
0
0
0
0
0
1
0
1
t11
t11
DB7
DOUT
DB0 DB7
DB0
STATUS REGISTER CONTENTS
IRQ
Figure 38. Interrupt Timing
Rev. A | Page 18 of 56
04481-A-039
READ STATUS REGISTER COMMAND
ADE7763
Interrupt Timing
Review the Serial Interface section before reading this section.
As previously described, when the IRQ output goes low, the
MCU ISR will read the interrupt status register to determine the
source of the interrupt. When reading the status register
contents, the IRQ output is set high upon the last falling edge of
SCLK of the first byte transfer (read interrupt status register
command). The IRQ output is held high until the last bit of the
next 15-bit transfer is shifted out (interrupt status register
contents)—see Figure 37. If an interrupt is pending at this time,
the IRQ output will go low again. If no interrupt is pending, the
IRQ output will stay high.
TEMPERATURE MEASUREMENT
There is an on-chip temperature sensor. A temperature
measurement can be made by setting Bit 5 in the mode register.
When Bit 5 is set logic high in the mode register, the ADE7763
initiates a temperature measurement of the next zero crossing.
When the zero crossing on Channel 2 is detected, the voltage
output from the temperature sensing circuit is connected to
ADC1 (Channel 1) for digitizing. The resulting code is
processed and placed in the temperature register (TEMP[7:0])
approximately 26 µs later (24 CLKIN/4 cycles). If enabled in the
interrupt enable register (Bit 5), the IRQ output will go active
low when the temperature conversion is finished.
The contents of the temperature register are signed (twos
complement) with a resolution of approximately 1.5 LSB/°C.
The temperature register produces a code of 0x00 when the
ambient temperature is approximately −25°C. The temperature
measurement is uncalibrated in the ADE7763 and might have
an offset tolerance as high as ±25°C.
stream. The DAC output is subtracted from the input signal. If
the loop gain is high enough, the average value of the DAC
output (and therefore the bit stream) will approach that of the
input signal level. For any given input value in a single sampling
interval, the data from the 1-bit ADC is virtually meaningless.
Only when a large number of samples are averaged can a
meaningful result be obtained. This averaging is carried out in
the second part of the ADC, the digital low-pass filter. By
averaging a large number of bits from the modulator, the lowpass filter can produce 24-bit data-words that are proportional
to the input signal level.
The Σ-∆ converter uses two techniques to achieve high resolution
from what is essentially a 1-bit conversion technique. The first
is oversampling. Oversampling means that the signal is sampled
at a rate (frequency) that is many times higher than the bandwidth of interest. For example, the sampling rate in the ADE7763
is CLKIN/4 (894 kHz) and the band of interest is 40 Hz to 2 kHz.
Oversampling has the effect of spreading the quantization noise
(noise due to sampling) over a wider bandwidth. With the noise
spread more thinly over a wider bandwidth, the quantization
noise in the band of interest decreases—see Figure 40. However,
oversampling alone is not efficient enough to improve the
signal-to-noise ratio (SNR) in the band of interest. For example,
an oversampling ratio of 4 is required just to increase the SNR
by 6 dB (1 bit). To keep the oversampling ratio at a reasonable
level, it is possible to shape the quantization noise so that the
majority of the noise lies at higher frequencies. In the Σ-∆
modulator, the noise is shaped by the integrator, which has a
high-pass-type response for the quantization noise. The result is
that most of the noise is at higher frequencies, where it can
be removed by the digital low-pass filter. This noise shaping is
shown in Figure 40.
ANALOG-TO-DIGITAL CONVERSION
The analog-to-digital conversion is carried out using two
second-order Σ-∆ ADCs. For simplicity, the block diagram in
Figure 39 shows a first-order Σ-∆ ADC. The converter
comprises two parts: the Σ-∆ modulator and the digital lowpass filter.
DIGITAL
FILTER
SIGNAL
INTEGRATOR
+
R
C
+
–
LATCHED
COMPARATOR
–
SAMPLING
FREQUENCY
SHAPED
NOISE
NOISE
0
2
MCLK/4
ANALOG
LOW-PASS FILTER
ANTIALIAS
FILTER (RC)
DIGITAL
LOW-PASS
FILTER
447
FREQUENCY (kHz)
894
HIGH RESOLUTION
OUTPUT FROM DIGITAL
LPF
SIGNAL
24
VREF
Figure 39. First-Order Σ-∆ ADC
A Σ-∆ modulator converts the input signal into a continuous
serial stream of 1s and 0s at a rate determined by the sampling
clock. In the ADE7763, the sampling clock is equal to CLKIN/4.
The 1-bit DAC in the feedback loop is driven by the serial data
Rev. A | Page 19 of 56
0
2
447
FREQUENCY (kHz)
894
Figure 40. Noise Reduction due to Oversampling and
Noise Shaping in the Analog Modulator
04481-A-041
.....10100101.....
1-BIT DAC
04481-A-040
NOISE
ADE7763
Antialias Filter
Reference Circuit
Figure 39 also shows an analog low-pass filter (RC) on the input
to the modulator. This filter prevents aliasing, which is an
artifact of all sampled systems. Aliasing means that frequency
components in the input signal to the ADC that are higher than
half the sampling rate of the ADC appear in the sampled signal
at a frequency below half the sampling rate. Figure 41 illustrates
the effect. Frequency components (shown as arrows) above half
the sampling frequency (also known as the Nyquist frequency,
i.e., 447 kHz) are imaged or folded back down below 447 kHz.
This happens with all ADCs, regardless of the architecture. In
the example shown, only frequencies near the sampling
frequency, i.e., 894 kHz, move into the band of interest for
metering, i.e., 40 Hz to 2 kHz. This allows the use of a very
simple LPF (low-pass filter) to attenuate high frequency (near
900 kHz) noise, and it prevents distortion in the band of interest.
For conventional current sensors, a simple RC filter (single-pole
LPF) with a corner frequency of 10 kHz produces an attenuation
of approximately 40 dB at 894 kHz—see Figure 41. The 20 dB
per decade attenuation is usually sufficient to eliminate the effects
of aliasing for conventional current sensors; however, for a di/dt
sensor such as a Rogowski coil, the sensor has a 20 dB per decade
gain. This neutralizes the –20 dB per decade attenuation
produced by one simple LPF. Therefore, when using a di/dt
sensor, care should be taken to offset the 20 dB per decade gain.
One simple approach is to cascade two RC filters to produce the
–40 dB per decade attenuation.
Figure 42 shows a simplified version of the reference output
circuitry. The nominal reference voltage at the REFIN/OUT pin is
2.42 V. This is the reference voltage used for the ADCs. However,
Channel 1 has three input range options that are selected by
dividing down the reference value used for the ADC in
Channel 1. The reference value used for Channel 1 is divided
down to ½ and ¼ of the nominal value by using an internal
resistor divider, as shown in Figure 42.
ALIASING EFFECTS
2
447
04481-A-042
0
894
FREQUENCY (kHz)
Figure 41. ADC and Signal Processing in Channel 1 Outline Dimensions
ADC Transfer Function
The following expression relates the output of the LPF in the
Σ-∆ ADC to the analog input signal level. Both ADCs in the
ADE7763 are designed to produce the same output code for the
same input signal level.
Code ( ADC ) = 3.0492 ×
VIN
× 262,144
VOUT
REFIN/OUT
2.42V
60µA
1.7kΩ
2.5V
12.5kΩ
12.5kΩ
12.5kΩ
REFERENCE INPUT
TO ADC CHANNEL 1
(RANGE SELECT)
2.42V, 1.21V, 0.6V
04481-A-043
12.5kΩ
Figure 42. Reference Circuit Output
The REFIN/OUT pin can be overdriven by an external source such as
a 2.5 V reference. Note that the nominal reference value supplied
to the ADCs is now 2.5 V, not 2.42 V, which increases the
nominal analog input signal range by 2.5/2.42 × 100% = 3% or
from 0.5 V to 0.5165 V.
CHANNEL 1 ADC
(1)
Therefore, with a full-scale signal on the input of 0.5 V and an
internal reference of 2.42 V, the ADC output code is nominally
165,151, or 0x2851F. The maximum code from the ADC is
±262,144; this is equivalent to an input signal level of ±0.794 V.
However, for specified performance, do not exceed the 0.5 V
full-scale input signal level.
PTAT
OUTPUT
IMPEDANCE
6kΩ
The voltage of the ADE7763 reference drifts slightly with changes
in temperature—see Table 1 for the temperature coefficient
specification (in ppm/°C). The value of the temperature drift
varies from part to part. Because the reference is used for the
ADCs in both Channels 1 and 2, any x% drift in the reference
results in 2x% deviation in the meter accuracy. The reference
drift that results from a temperature change is usually very
small, typically much smaller than the drift of other components
on a meter. However, if guaranteed temperature performance is
needed, use an external voltage reference. Alternatively, the
meter can be calibrated at multiple temperatures. Real-time
compensation can be achieved easily by using the on-chip
temperature sensor.
SAMPLING
FREQUENCY
IMAGE
FREQUENCIES
MAXIMUM
LOAD = 10µA
Figure 43 shows the ADC and signal processing chain for
Channel 1. In waveform sampling mode, the ADC outputs a
signed, twos complement, 24-bit data-word at a maximum of
27.9 kSPS (CLKIN/128). With the specified full-scale analog
input signal of 0.5 V (or 0.25 V or 0.125 V—see the Analog
Inputs section), the ADC produces an output code that is
approximately between 0x28 51EC (+2,642,412d) and
0xD7 AE14 (–2,642,412d)—see Figure 43.
Rev. A | Page 20 of 56
ADE7763
2.42V, 1.21V, 0.6V
×1, ×2, ×4,
REFERENCE
×8, ×16
{GAIN[2:0]}
V1P
{GAIN[4:3]}
HPF
WAVEFORM SAMPLE
REGISTER
DIGITAL
INTEGRATOR*
ADC 1
PGA1
V1
CURRENT RMS (IRMS)
CALCULATION
ACTIVE AND REACTIVE
POWER CALCULATION
dt
V1N
50Hz
CHANNEL 1
(CURRENT WAVEFORM)
DATA RANGE AFTER
INTEGRATOR (50Hz)
0x1E F73C
V1
0.5V, 0.25V,
0.125V, 62.5mV,
31.3mV, 15.6mV,
0x28 51EC
0V
CHANNEL 1
(CURRENT WAVEFORM)
DATA RANGE
0x0 0000
0x00 0000
0xEI 08C4
0x28 51EC
0xD 7AE4
ANALOG
INPUT
RANGE
ADC OUTPUT
WORD RANGE
0x00 0000
60Hz
0xD 7AE4
CHANNEL 1
(CURRENT WAVEFORM)
DATA RANGE AFTER
INTEGRATOR (60Hz)
0x19 CE08
0xE6 31F8
04481-A-044
0x00 0000
*WHEN DIGITAL INTEGRATOR IS ENABLED, FULL-SCALE OUTPUT DATA IS ATTENUATED
DEPENDING ON THE SIGNAL FREQUENCY BECAUSE THE INTEGRATOR HAS A –20dB/DECADE
FREQUENCY RESPONSE. WHEN DISABLED, THE OUTPUT IS NOT ATTENUATED FURTHER.
Figure 43. ADC and Signal Processing in Channel 1
Channel 1 Sampling
Channel 1 RMS Calculation
The waveform samples may be routed to the waveform register
(MODE[14:13] = 1, 0) for the system master (MCU) to read. In
waveform sampling mode, set the WSMP bit (Bit 3) in the
interrupt enable register to Logic 1. The active and apparent
power as well as the energy calculation remain uninterrupted
during waveform sampling.
The root mean square (rms) value of a continuous signal V(t) is
defined as
In waveform sampling mode, choose one of four output sample
rates using Bits 11 and 12 of the mode register (WAVSEL 1, 0).
The output sample rate can be 27.9 kSPS, 14 kSPS, 7 kSPS, or
3.5 kSPS—see the Mode Register (0X09) section. The interrupt
request output, IRQ, signals a new sample availability by going
active low. The timing is shown in Figure 44. The 24-bit waveform samples are transferred from the ADE7763 one byte (eight
bits) at a time, with the most significant byte shifted out first.
The 24-bit data-word is right justified—see the Serial Interface
section. The interrupt request output IRQ stays low until the
interrupt routine reads the reset status register—see the
Interrupts section.
IRQ
VRMS =
VRMS =
READ FROM WAVEFORM
0 0 0 01 HEX
SIGN
CHANNEL 1 DATA
(24 BITS)
1 N 2
× ∑ V (i)
N i =1
The ADE7763 simultaneously calculates the rms values for
Channel 1 and Channel 2 in different registers. Figure 45 shows
the detail of the signal processing chain for the rms calculation
on Channel 1. The Channel 1 rms value is processed from the
samples used in the Channel 1 waveform sampling mode. The
Channel 1 rms value is stored in an unsigned, 24-bit register
(IRMS). One LSB of the Channel 1 rms register is equivalent to
1 LSB of a Channel 1 waveform sample. The update rate of the
Channel 1 rms measurement is CLKIN/4.
04481-A-045
DOUT
(2)
For time sampling signals, the rms calculation involves squaring
the signal, taking the average, and obtaining the square root:
SCLK
DIN
1 T 2
× ∫ V (t )dt
T 0
Figure 44. Waveform Sampling Channel 1
Rev. A | Page 21 of 56
(3)
ADE7763
CURRENT SIGNAL (i(t))
0x28 51EC
IRMSOS[11:0]
IRMS(t)
0x00
HPF1
LPF3
+
24
24
IRMS
04481-A-046
0xD7 AE14
CHANNEL 1
217 216 215 0x1C 82B3
0x00
sgn 225 226 227
Figure 45. Channel 1 RMS Signal Processing
not the same as it is for Channel 1. The Channel 2 waveform
sample is a 16-bit word and sign extended to 24 bits. For normal
operation, the differential voltage signal between V2P and V2N
should not exceed 0.5 V. With maximum voltage input (±0.5 V
at PGA gain of 1), the output from the ADC swings between
0x2852 and 0xD7AE (±10,322d). However, before being passed
to the waveform register, the ADC output is passed through a
single-pole, low-pass filter with a cutoff frequency of 140 Hz.
The plots in Figure 46 show the magnitude and phase response
of this filter.
0
50Hz, –0.52dB
–10
IRMS 0 2 + IRMSOS × 32768
(4)
where IRMS0 is the rms measurement without offset correction.
–4
50Hz, –19.7°
One LSB of the Channel 1 rms offset is equivalent to 32,768 LSB
of the square of the Channel 1 rms register. Assuming that the
maximum value from the Channel 1 rms calculation is
1,868,467d with full-scale ac inputs, then 1 LSB of the Channel 1
rms offset represents 0.46% of the measurement error at –60 dB
down of full scale.
0
–2
–20
PHASE (Degrees)
The ADE7763 incorporates a Channel 1 rms offset compensation register (IRMSOS). This is a 12-bit, signed register that can
be used to remove offset in the Channel 1 rms calculation. An
offset might exist in the rms calculation due to input noises that
are integrated in the dc component of V2(t). The offset calibration
allows the content of the IRMS register to be maintained at 0
when no input is present on Channel 1.
IRMS =
60Hz, –0.73dB
–6
–30
60Hz, –23.2°
–40
–8
–50
–10
–60
–12
–70
–14
–80
–16
–90
101
102
FREQUENCY (Hz)
–18
103
GAIN (dB)
Channel 1 RMS Offset Compensation
04481-A-047
With the specified full-scale analog input signal of 0.5 V, the ADC
produces an output code that is approximately ±2,642,412d—
see the Channel 1 ADC section. The equivalent rms value of a
full-scale ac signal is 1,868,467d (0x1C82B3). The current rms
measurement provided in the ADE7763 is accurate to within
1% for signal input between full scale and full scale/100.
Converting the register value to its equivalent in amps must be
done externally in the microprocessor using an amps/LSB
constant. To minimize noise, synchronize the reading of the
rms register with the zero crossing of the voltage input and take
the average of a number of readings.
Figure 46. Magnitude and Phase Response of LPF1
The LPF1 has the effect of attenuating the signal. For example,
if the line frequency is 60 Hz, the signal at the output of LPF1
will be attenuated by about 8%.
To measure the offset of the rms measurement, two data points
are needed from nonzero input values, for example, the base
current, Ib, and Imax/100. The offset can be calculated from these
measurements.
|H(f)| =
1
⎛ 60 Hz ⎞
⎟
1+ ⎜
⎜ 140 Hz ⎟
⎝
⎠
2
= 0.919 = −0.73 db
Note LPF1 does not affect the active power calculation. The
signal processing chain in Channel 2 is illustrated in Figure 47.
CHANNEL 2 ADC
Channel 2 Sampling
In Channel 2 waveform sampling mode (MODE[14:13] = 1, 1
and WSMP = 1), the ADC output code scaling for Channel 2 is
Rev. A | Page 22 of 56
(5)
ADE7763
2.42V
×1, ×2, ×4,
REFERENCE
×8, ×16
{GAIN[7:5]}
V2P
PGA2
V2
ACTIVE AND REACTIVE
ENERGY CALCULATION
ADC 2
LPF1
V2N
ANALOG
V1
INPUT RANGE
0.5V, 0.25V, 0.125V,
62.5mV, 31.25mV
0V
0x2852
0x2581
VRMS CALCULATION
AND WAVEFORM
SAMPLING
(PEAK/SAG/ZX)
LPF OUTPUT
WORD RANGE
04481-A-048
0x0000
0xDAE8
0xD7AE
Figure 47. ADC and Signal Processing in Channel 2
VOLTAGE SIGNAL (V(t))
0x2518
VRMOS[11:0]
sgn 29 28
22 21 20
0xDAE8
LPF1
VRMS[23:0]
0x17D338
LPF3
+
CHANNEL 2
+
0x00
04481-A-049
0x0
Figure 48. Channel 2 RMS Signal Processing
Channel 2 has only one analog input range (0.5 V differential).
Like Channel 1, Channel 2 has a PGA with gain selections of 1,
2, 4, 8, and 16. For energy measurement, the output of the ADC
is passed directly to the multiplier and is not filtered. An HPF is
not required to remove any dc offset; it is only required that the
offset is removed from one channel to eliminate errors caused
by offsets in the power calculation. In waveform sampling mode,
one of four output sample rates can be chosen by using Bits 11
and 12 of the mode register. The available output sample rates
are 27.9 kSPS, 14 kSPS, 7 kSPS, or 3.5 kSPS—see the Mode
Register (0X09) section. The interrupt request output IRQ
indicates that a sample is available by going active low. The
timing is the same as that for Channel 1, as shown in Figure 44.
Channel 2 RMS Calculation
Figure 48 shows the details of the signal processing chain for the
rms calculation on Channel 2. The Channel 2 rms value is
processed from the samples used in the Channel 2 waveform
sampling mode. The rms value is slightly attenuated due to
LPF1. The Channel 2 rms value is stored in the unsigned, 24-bit
VRMS register. The update rate of the Channel 2 rms
measurement is CLKIN/4.
With the specified full-scale ac analog input signal of 0.5 V, the
output from LPF1 swings between 0x2518 and 0xDAE8 at
60 Hz—see the Channel 2 ADC section. The equivalent rms
value of this full-scale ac signal is approximately 1,561,400
(0x17 D338) in the VRMS register. The voltage rms measurement provided in the ADE7763 is accurate to within ±0.5% for
signal input between full scale and full scale/20. The conversion
from the register value to volts must be done externally in the
microprocessor using a volts/LSB constant. Because the low-pass
filter used for calculating the rms value is imperfect, there is some
ripple noise from 2ω term present in the rms measurement. To
minimize the effect of noise in the reading, synchronize the rms
reading with the zero crossings of the voltage input.
Channel 2 RMS Offset Compensation
The ADE7763 incorporates a Channel 2 rms offset
compensation register (VRMSOS). This is a 12-bit, signed
register that can be used to remove offset in the Channel 2 rms
calculation. An offset could exist in the rms calculation due to
input noises and dc offset in the input samples. The offset
calibration allows the contents of the VRMS register to be
maintained at 0 when no voltage is applied. One LSB of the
Channel 2 rms offset is equivalent to 1 LSB of the rms register.
Assuming that the maximum value of the Channel 2 rms
calculation is 1,561,400d with full-scale ac inputs, then 1 LSB of
the Channel 2 rms offset represents 0.064% of measurement
error at –60 dB down of full scale.
VRMS = VRMS0 + VRMSOS
where VRMS0 is the rms measurement without offset
correction.
The voltage rms offset compensation should be done by testing
the rms results at two nonzero input levels. One measurement
can be done close to full scale and the other at approximately
full scale/10. The voltage offset compensation can be derived
from these measurements. If the voltage rms offset register does
not have enough range, the CH2OS register can also be used.
Rev. A | Page 23 of 56
(6)
ADE7763
V1P
PHASE COMPENSATION
V2P
1
ADC 2
DELAY BLOCK
2.22µs/LSB
V2N
5
0
0 0 1 0 1 1
V2
CHANNEL 2 DELAY
REDUCED BY 4.44µs
(0.1°LEAD AT 60Hz)
0x0B IN PHCAL [5.0]
V2
V1
PHCAL[5:0]
–102.12µs TO +39.96µs
0.1°
V1
04481-A-050
PGA2
V2
60Hz
60Hz
Figure 49. Phase Calibration
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
102
103
104
FREQUENCY (Hz)
04481-A-051
0
–0.1
Figure 50. Combined Phase Response of HPF and
Phase Compensation (10 Hz to 1 kHz)
0.20
0.18
0.16
0.14
0.12
0.10
0.08
0.06
0.04
0.02
0
40
45
50
55
60
65
FREQUENCY (Hz)
Figure 51. Combined Phase Response of HPF and
Phase Compensation (40 Hz to 70 Hz)
Rev. A | Page 24 of 56
70
04481-A-052
The register is centered at 0Dh, so that writing 0Dh to the register
produces 0 delay. By changing the PHCAL register, the time
delay in the Channel 2 signal path can change from –102.12 µs
to +39.96 µs (CLKIN = 3.579545 MHz). One LSB is equivalent
to 2.22 µs (CLKIN/8) time delay or advance. A line frequency of
60 Hz gives a phase resolution of 0.048° at the fundamental (i.e.,
360° × 2.22 µs × 60 Hz). Figure 49 illustrates how the phase
compensation is used to remove a 0.1° phase lead in Channel 1
due to the external transducer. To cancel the lead (0.1°) in
Channel 1, a phase lead must also be introduced into Channel 2.
The resolution of the phase adjustment allows the introduction
of a phase lead in increments of 0.048°. The phase lead is
achieved by introducing a time advance in Channel 2. A time
advance of 4.44 µs is made by writing −2 (0x0B) to the time delay
block, thus reducing the amount of time delay by 4.44 µs, or
equivalently, a phase lead of approximately 0.1° at line frequency
of 60 Hz. 0x0B represents –2 because the register is centered
with 0 at 0Dh.
LPF2
24
PHASE (Degrees)
The phase calibration register (PHCAL[5:0]) is a twos complement, signed, single-byte register that has values ranging from
0x21 (–31d) to 0x1F (+31d).
24
ADC 1
V1N
PHASE (Degrees)
When the HPF is disabled, the phase error between Channel 1
and Channel 2 is 0 from dc to 3.5 kHz. When HPF is enabled,
Channel 1 has the phase response illustrated in Figure 50 and
Figure 51. Figure 52 shows the magnitude response of the filter.
As seen from the plots, the phase response is almost 0 from
45 Hz to 1 kHz, which is all that is required in typical energy
measurement applications. However, despite being internally
phase-compensated, the ADE7763 must work with transducers,
which could have inherent phase errors. For example, a phase
error of 0.1° to 0.3° is not uncommon for a current transformer
(CT). Phase errors can vary from part to part and must be
corrected in order to perform accurate power calculations. The
errors associated with phase mismatch are particularly
noticeable at low power factors. The ADE7763 provides a
means of digitally calibrating these small phase errors by
allowing a short time delay or time advance to be introduced
into the signal processing chain to compensate for these errors.
Because the compensation is in time, this technique should only
be used for small phase errors in the range of 0.1° to 0.5°.
Correcting large phase errors using a time shift technique can
introduce significant phase errors at higher harmonics.
HPF
PGA1
V1
ADE7763
0.4
The instantaneous power signal p(t) is generated by multiplying
the current and voltage signals. The dc component of the instantaneous power signal is then extracted by LPF2 (low-pass filter)
to obtain the active power information. This process is illustrated
in Figure 53.
0.3
ERROR (%)
0.2
0.1
INSTANTANEOUS
POWER SIGNAL
0.0
p(t) = v × i-v × i × cos(2ωt)
0x19 999A
–0.1
ACTIVE REAL POWER
SIGNAL = v × i
–0.2
–0.3
56
58
60
62
64
66
FREQUENCY (Hz)
0x0 0000
Figure 52. Combined Gain Response of HPF and Phase Compensation
CURRENT
i(t) = 2 × i × sin(ωt)
ACTIVE POWER CALCULATION
Power is defined as the rate of energy flow from the source to
the load. It is defined as the product of the voltage and current
waveforms. The resulting waveform is called the instantaneous
power signal and is equal to the rate of energy flow at any given
time. The unit of power is the watt or joules/s. Equation 9 gives
an expression for the instantaneous power signal in an ac system.
v(t ) = 2 ×V sin(ω t )
(7)
i(t ) = 2 × I sin(ω t )
(8)
where:
VOLTAGE
v(t) = 2 × v × sin(ωt)
Figure 53. Active Power Calculation
Because LPF2 does not have an ideal “brick wall” frequency
response (see Figure 54), the active power signal has some
ripple due to the instantaneous power signal. This ripple is
sinusoidal and has a frequency equal to twice the line frequency.
Because the ripple is sinusoidal in nature, it is removed when the
active power signal is integrated to calculate energy—see the
Energy Calculation section.
V is the rms voltage.
I is the rms current.
0
–4
p (t ) = v (t ) × i (t )
–8
(9)
The average power over an integral number of line cycles (n) is
given by the expression in Equation 10.
dB
p(t ) = VI − VI cos(2ωt )
04481-A-054
–0.4
54
04481-A-053
VI
0xC CCCD
–12
–16
∫
nT
p ( t ) dt = VI
(10)
0
where:
–20
–24
1
T is the line cycle period.
P is the active or real power.
3
10
30
FREQUENCY (Hz)
Figure 54. Frequency Response of LPF2
Note that the active power is equal to the dc component of the
instantaneous power signal p(t) in Equation 8, i.e., VI. This is
the relationship used to calculate active power in the ADE7763.
Rev. A | Page 25 of 56
100
04481-A-055
1
P=
nT
ADE7763
APOS[15:0]
CURRENT
CHANNEL
WDIV[7:0]
AENERGY[23:0]
LPF2
+
23
+
0
UPPER 24 BITS ARE
ACCESSIBLE THROUGH
AENERGY[23:0] REGISTER
%
VOLTAGE
CHANNEL
WGAIN[11:0]
48
0
4
CLKIN
OUTPUT LPF2
T
WAVEFORM
REGISTER
VALUES
OUTPUTS FROM THE LPF2 ARE
ACCUMULATED (INTEGRATED) IN
THE INTERNAL ACTIVE ENERGY REGISTER
04481-A-056
ACTIVE POWER
SIGNAL
TIME (nT)
Figure 55. Active Energy Calculation
ACTIVE POWER OUTPUT
Figure 55 shows the signal processing chain for the active power
calculation. The active power is calculated by low-pass filtering
the instantaneous power signal. Note that when reading the
waveform samples from the output of LPF2, the gain of the
active energy can be adjusted by using the multiplier and watt
gain register (WGAIN[11:0]). The gain is adjusted by writing a
twos complement 12-bit word to the watt gain register.
Equation 11 shows how the gain adjustment is related to the
contents of the watt gain register:
0x1 3333
POSITIVE
POWER
0xCCCD
0x6666
0x0 0000
0xF 999A
NEGATIVE
POWER
0xF 3333
0xE CCCD
0x7FF
0x800
{WGAIN[11:0]}
⎛
⎧ WGAIN ⎫ ⎞
Output WGAIN = ⎜⎜ Active Power × ⎨1 +
⎬ ⎟⎟
212 ⎭ ⎠
⎩
⎝
ACTIVE POWER
CALIBRATION RANGE
(11)
04481-A-057
0x000
Figure 56. Active Power Calculation Output Range
For example, when 0x7FF is written to the watt gain register, the
power output is scaled up by 50%. 0x7FF = 2047d, 2047/212 = 0.5.
Similarly, 0x800 = –2048d (signed twos complement) and
power output is scaled by –50%. Each LSB scales the power
output by 0.0244%. Figure 56 shows the maximum code
(hexadecimal) output range for the active power signal (LPF2).
Note that the output range changes depending on the contents
of the watt gain register. The minimum output range is given
when the watt gain register contents are equal to 0x800, and the
maximum range is given by writing 0x7FF to the watt gain
register. This can be used to calibrate the active power (or
energy) calculation.
ENERGY CALCULATION
As stated earlier, power is defined as the rate of energy flow.
This relationship is expressed mathematically in Equation 12.
P=
dE
dt
(12)
where:
P is power.
E is energy.
Conversely, energy is given as the integral of power.
∫
E = Pdt
Rev. A | Page 26 of 56
(13)
ADE7763
APOS[15:0]
sgn 26 25
I
CURRENT SIGNAL – i(t)
LPF2
24
+
FOR WAVEF0RM
SAMPLING
24
HPF
2-6 2-7 2-8
0x1 9999
+
32
FOR WAVEFORM
ACCUMULATION
MULTIPLIER
VOLTAGE SIGNAL– v(t)
INSTANTANEOUS
POWER SIGNAL – p(t)
0xC CCCD
WGAIN[11:0]
0x19 999A
04481-A-058
1
V
0x00 0000
Figure 57. Active Power Signal Processing
The ADE7763 achieves the integration of the active power
signal by continuously accumulating the active power signal in
an internal unreadable 49-bit energy register. The active energy
register (AENERGY[23:0]) represents the upper 24 bits of this
internal register. This discrete time accumulation or summation
is equivalent to integration in continuous time. Equation 14
expresses this relationship.
⎧∞
⎫
E = ∫ p(t )dt = Lim ⎨∑ p(nT ) × T ⎬
t →0
⎩ n =1
⎭
(14)
the WSMP bit (Bit 3) in the interrupt enable register to 1. Like
Channel 1 and Channel 2 waveform sampling modes, the
waveform data is available at sample rates of 27.9 kSPS, 14 kSPS,
7 kSPS, or 3.5 kSPS—see Figure 44.
Figure 58 shows this energy accumulation for full-scale signals
(sinusoidal) on the analog inputs. The three curves illustrate the
minimum time for the energy register to roll over when the active
power gain register contents are 0x7FF, 0x000, and 0x800. The
watt gain register is used to carry out power calibration. As
shown, the fastest integration time occurs when the watt gain
register is set to maximum full scale, i.e., 0x7FF.
where:
AENERGY[23:0]
n is the discrete time sample number.
T is the sample period.
0x7F FFFF
The discrete time sample period (T) for the accumulation
register is 1.1 µs (4/CLKIN). In addition to calculating the
energy, this integration removes any sinusoidal components
that might be in the active power signal.
WGAIN = 0x7FF
WGAIN = 0x000
WGAIN = 0x800
0x3F FFFF
0x00 0000
The output of the multiplier is divided by WDIV. If the value in
the WDIV register is equal to 0, then the internal active energy
register is divided by 1. WDIV is an 8-bit, unsigned register.
After dividing by WDIV, the active energy is accumulated in a
49-bit internal energy accumulation register. The upper 24 bits
of this register are accessible through a read to the active energy
register (AENERGY[23:0]). A read to the RAENERGY register
returns the content of the AENERGY register, and the upper
24 bits of the internal register are cleared. As shown in Figure 57,
the active power signal is accumulated in an internal 49-bit,
signed register. The active power signal can be read from the
waveform register by setting MODE[14:13] = 0, 0 and setting
8
12.5
TIME (minutes)
0x40 0000
0x80 0000
04481-A-059
Figure 57 shows this discrete time integration, or accumulation.
The active power signal in the waveform register is continuously
added to the internal active energy register. This addition is a
signed addition; therefore, negative energy is subtracted from
the active energy contents. The exception to this is when POAM
is selected in the MODE[15:0] register, in which case only
positive energy contributes to the active energy accumulation—
see the Positive-Only Accumulation Mode section.
4 6.2
Figure 58. Energy Register Rollover Time for Full-Scale Power
(Minimum and Maximum Power Gain)
Note that the energy register contents roll over to full-scale
negative (0x80 0000) and continue increasing in value when the
power or energy flow is positive—see Figure 58. Conversely, if
the power was negative, the energy register would underflow to
full-scale positive (0x7F FFFF) and continue decreasing in
value.
By using the interrupt enable register, the ADE7763 can be
configured to issue an interrupt (IRQ) when the active energy
register is more than half full (positive or negative), or when an
overflow or underflow occurs.
Rev. A | Page 27 of 56
ADE7763
Integration Time under Steady Load
CFNUM[11:0]
11
As mentioned in the last section, the discrete time sample
period (T) for the accumulation register is 1.1 µs (4/CLKIN).
With full-scale sinusoidal signals on the analog inputs and the
WGAIN register set to 0x000, the average word value from each
LPF2 is 0xC CCCD—see Figure 53. The maximum positive
value that can be stored in the internal 49-bit register before it
overflows is 248, or 0xFFFF FFFF FFFF. The integration time
under these conditions with WDIV = 0 is calculated as follows:
Time =
0xFFFF FFFF FFFF
× 1.12 µs = 375.8 s = 6.26 min
0xC CCCD
Figure 59. Energy-to-Frequency Conversion
(16)
The ADE7763 incorporates an active power offset register
(APOS[15:0]). This is a signed, twos complement, 16-bit
register that can be used to remove offsets in the active power
calculation—see Figure 57. An offset could exist in the power
calculation due to crosstalk between channels on the PCB or in
the IC itself. The offset calibration allows the contents of the
active power register to be maintained at 0 when no power is
being consumed.
The 256 LSBs (APOS = 0x0100) written to the active power
offset register are equivalent to 1 LSB in the waveform sample
register. Assuming the average value output from LPF2 is
0xC CCCD (838,861d) when inputs on Channels 1 and 2 are
both at full scale. At −60 dB down on Channel 1 (1/1000 of the
Channel 1 full-scale input), the average word value output from
LPF2 is 838.861 (838,861/1,000). One LSB in the LPF2 output
has a measurement error of 1/838.861 × 100% = 0.119% of the
average value. The active power offset register has a resolution
equal to 1/256 LSB of the waveform register; therefore, the
power offset correction resolution is 0.00047%/LSB
(0.119%/256) at –60 dB.
ENERGY-TO-FREQUENCY CONVERSION
The ADE7763 provides energy-to-frequency conversion for
calibration purposes. After initial calibration at manufacturing,
the manufacturer or end customer often verifies the energy meter
calibration. One convenient way to verify the meter calibration
is for the manufacturer to provide an output frequency, which is
proportional to the energy or active power under steady load
conditions. This output frequency can provide a simple, singlewire, optically isolated interface to external calibration equipment. Figure 59 illustrates the energy-to-frequency conversion.
0
CFDEN[11:0]
04481-A-060
11
(15)
POWER OFFSET CALIBRATION
CF
0
AENERGY[48:0]
When WDIV is set to a value other than 0, the integration time
varies, as shown in Equation 16.
Time = TimeWDIV = 0 × WDIV
%
DFC
48
0
A digital-to-frequency converter (DFC) is used to generate the
CF pulsed output. The DFC generates a pulse each time 1 LSB
in the active energy register is accumulated. An output pulse is
generated when (CFDEN + 1)/(CFNUM + 1) number of pulses
are generated at the DFC output. Under steady load conditions,
the output frequency is proportional to the active power.
The maximum output frequency, with ac input signals at full
scale, CFNUM = 0x00, and CFDEN = 0x00, is approximately
23 kHz.
There are two unsigned, 12-bit registers, CFNUM[11:0] and
CFDEN[11:0], that can be used to set the CF frequency to a wide
range of values. These frequency-scaling registers are 12-bit
registers that can scale the output frequency by 1/212 to 1 with a
step of 1/212.
If the value 0 is written to any of these registers, the value 1 will
be applied to the register. The ratio (CFNUM + 1)/(CFDEN + 1)
should be smaller than 1 to ensure proper operation. If the ratio
of the registers (CFNUM + 1)/(CFDEN + 1) is greater than 1, the
register values will be adjusted to a ratio (CFNUM + 1)/
(CFDEN + 1) of 1. For example, if the output frequency is
1.562 kHz while the contents of CFDEN are 0 (0x000), then the
output frequency can be set to 6.1 Hz by writing 0xFF to the
CFDEN register.
When CFNUM and CFDEN are both set to one, the CF pulse
width is fixed at 16 CLKIN/4 clock cycles, approximately 18 µs
with a CLKIN of 3.579545 MHz. If the CF pulse output is longer
than 180 ms for an active energy frequency of less than 5.56 Hz,
the pulse width is fixed at 90 ms. Otherwise, the pulse width is
50% of the duty cycle.
The output frequency has a slight ripple at a frequency equal to
twice the line frequency. This is due to imperfect filtering of the
instantaneous power signal to generate the active power signal—
see the Active Power Calculation section. Equation 8 gives an
expression for the instantaneous power signal. This is filtered by
LPF2, which has a magnitude response given by Equation 17.
H( f ) =
1
f2
1+
8.9 2
Rev. A | Page 28 of 56
(17)
ADE7763
The active power signal (output of LPF2) can be rewritten as
⎡
⎤
⎢
⎥
⎢
⎥
VI
p (t ) = VI − ⎢
⎥ × cos( 4π f L t )
2 ⎥
⎢
⎛2f ⎞
⎢ 1+ ⎜ L ⎟ ⎥
⎝ 8.9 ⎠ ⎥⎦
⎢⎣
(18)
where fL is the line frequency, for example, 60 Hz.
From Equation 13,
⎤
⎡
⎥
⎢
⎥
⎢
VI
E (t ) = VIt − ⎢
⎥ × sin( 4π f L t )
2
⎢
⎛ 2 fL ⎞ ⎥
⎢ 4π f L 1 + ⎜
⎟ ⎥
⎝ 8.9 ⎠ ⎥⎦
⎣⎢
contribute to the energy calculation over time. However, the
ripple might be observed in the frequency output, especially at
higher output frequencies. The ripple becomes larger as a
percentage of the frequency at larger loads and higher output
frequencies. This occurs because the integration or averaging
time in the energy-to-frequency conversion process is shorter at
higher output frequencies. Consequently, some of the sinusoidal
ripple in the energy signal is observable in the frequency output.
Choosing a lower output frequency at CF for calibration can
significantly reduce the ripple. Also, averaging the output
frequency by using a longer gate time for the counter achieves
the same results.
E(t)
Vlt
Note that in Equation 19 there is a small ripple in the energy
calculation due to a sin(2ωt) component. This is shown graphically in Figure 60. The active energy calculation is represented
by the dashed, straight line and is equal to V × I × t. The sinusoidal ripple in the active energy calculation is also shown.
Because the average value of a sinusoid is 0, the ripple does not
VI
4×π×fL(1+2×fL/8. 9Hz )
–
sin(4×π×fL×t)
t
Figure 60. Output Frequency Ripple
WGAIN[11:0]
OUTPUT
FROM
LPF2
+
+
0
WDIV[7:0]
23
LPF1
ZERO CROSSING
DETECTION
CALIBRATION
CONTROL
0
LAENERGY[23:0]
LINECYC[15:0]
Figure 61. Energy Calculation Line Cycle Energy Accumulation Mode
Rev. A | Page 29 of 56
ACCUMULATE ACTIVE
ENERGY IN INTERNAL
REGISTER AND UPDATE
THE LAENERGY REGISTER
AT THE END OF LINECYC
LINE CYCLES
04481-A-062
APOS[15:0]
FROM
CHANNEL 2
ADC
48
%
04481-0-061
(19)
ADE7763
LINE CYCLE ENERGY ACCUMULATION MODE
In line cycle energy accumulation mode, the energy accumulation of the ADE7763 can be synchronized to the Channel 2
zero crossing so that active energy accumulates over an integral
number of half line cycles. The advantage of summing the active
energy over an integral number of line cycles is that the
sinusoidal component in the active energy is reduced to 0. This
eliminates ripple in the energy calculation. Energy is calculated
more accurately and in a shorter time because the integration
period is shortened. By using the line cycle energy accumulation
mode, the energy calibration can be greatly simplified, and the
time required to calibrate the meter can be significantly reduced.
The ADE7763 is placed in line cycle energy accumulation mode
by setting Bit 7 (CYCMODE) in the mode register. In line cycle
energy accumulation mode, the ADE7763 accumulates the
active power signal in the LAENERGY register (Address 0x04)
for an integral number of line cycles, as shown in Figure 61. The
number of half line cycles is specified in the LINECYC register
(Address 0x1C). The ADE7763 can accumulate active power for
up to 65,535 half line cycles. Because the active power is
integrated on an integral number of line cycles, the CYCEND
flag in the interrupt status register is set (Bit 2) at the end of a
line cycle energy accumulation cycle. If the CYCEND enable bit
in the interrupt enable register is enabled, the IRQ output also
will go active low. Therefore, the IRQ line can also be used to
signal the completion of the line cycle energy accumulation.
Another calibration cycle can start as long as the CYCMODE
bit in the mode register is set.
Note that in this mode, the 16-bit LINECYC register can hold a
maximum value of 65,535. In other words, the line energy
accumulation mode can be used to accumulate active energy for
a maximum duration of 65,535 half line cycles. At 60 Hz line
frequency, this translates to a total duration of 65,535/
120 Hz = 546 seconds.
POSITIVE-ONLY ACCUMULATION MODE
In positive-only accumulation mode, the energy accumulation
is only done for positive power, ignoring any occurrence of
negative power above or below the no-load threshold, as shown
in Figure 62. The CF pulse also reflects this accumulation
method when in this mode. Positive-only accumulation mode is
activated by setting the MSB of the mode register (MODE[15]).
The default setting for this mode is off. Transitions in the
direction of power flow, going from negative to positive or
positive to negative, set the IRQ pin to active low if the PPOS
and PNEG bits are set in the interrupt enable register. The
corresponding PPOS and PNEG bits in the interrupt status
register show which transition has occurred—see the register
descriptions in Table 9.
ACTIVE ENERGY
From Equations 13 and 18,
∫
⎫
⎪ nT
⎪⎪
⎬ × cos( 2π f t ) dt
⎪ 0
⎪
⎪⎭
ACTIVE POWER
∫
(20)
NO-LOAD
THRESHOLD
IRQ
where:
PPOS
PNEG
PPOS
PNEG PPOS PNEG
INTERRUPT STATUS REGISTERS
n is an integer.
T is the line cycle period.
Figure 62. Energy Accumulation in Positive-Only Accumulation Mode
NO-LOAD THRESHOLD
Since the sinusoidal component is integrated over an integral
number of line cycles, its value is always 0. Therefore,
∫
nT
E = VIdt + 0
(21)
0
E ( t ) = VInT
04481-A-063
⎧
⎪
⎪⎪
VI
E (t ) = VI dt − ⎨
2
⎪
⎛ f ⎞
0
⎟
⎪ 1+ ⎜
⎪⎩
⎝ 8. 9 ⎠
nT
NO-LOAD
THRESHOLD
(22)
The ADE7763 includes a no-load threshold feature on the
active energy that eliminates any creep effects in the meter. This
is accomplished because energy does not accumulate if the
multiplier output is below the no-load threshold. This threshold
is 0.001% of the full-scale output frequency of the multiplier.
Compare this value to the IEC1036 specification, which states
that the meter must start up with a load equal to or less than
0.4% Ib. This standard translates to 0.0167% of the full-scale
output frequency of the multiplier.
Rev. A | Page 30 of 56
ADE7763
APPARENT POWER CALCULATION
The apparent power is the maximum power that can be
delivered to a load. Vrms and Irms are the effective voltage and
current delivered to the load; the apparent power (AP) is
defined as Vrms × Irms. The angle θ between the active power and
the apparent power generally represents the phase shift due to
nonresistive loads. For single-phase applications, θ represents
the angle between the voltage and the current signals—see
Figure 63. Equation 24 gives an expression of the instantaneous
power signal in an ac system with a phase shift.
APPARENT POWER
04481-A-064
REACTIVE
POWER
θ
ACTIVE POWER
Figure 63. Power Triangle
v(t ) = 2 Vrms sin(ωt )
i (t ) = 2 I rms sin(ωt + θ )
(23)
The gain of the apparent energy can be adjusted by using the
multiplier and VAGAIN register (VAGAIN[11:0]). The gain is
adjusted by writing a twos complement, 12-bit word to the
VAGAIN register. Equation 25 shows how the gain adjustment
is related to the contents of the VAGAIN register.
⎛
⎧ VAGAIN ⎫ ⎞
OutputVAGAIN = ⎜⎜ Apparent Power × ⎨1 +
⎬ ⎟⎟ (25)
212 ⎭ ⎠
⎩
⎝
For example, when 0x7FF is written to the VAGAIN register, the
power output is scaled up by 50%. 0x7FF = 2047d, 2047/212 = 0.5.
Similarly, 0x800 = –2047d (signed, twos complement) and power
output is scaled by –50%. Each LSB represents 0.0244% of the
power output. The apparent power is calculated with the current
and voltage rms values obtained in the rms blocks of the
ADE7763. Figure 65 shows the maximum code (hexadecimal)
output range of the apparent power signal. Note that the output
range changes depending on the contents of the apparent power
gain registers. The minimum output range is given when the
apparent power gain register content is equal to 0x800; the
maximum range is given by writing 0x7FF to the apparent
power gain register. This can be used to calibrate the apparent
power (or energy) calculation in the ADE7763.
APPARENT POWER 100% FS
APPARENT POWER 150% FS
APPARENT POWER 50% FS
p (t ) = v (t ) × i (t )
p (t ) = Vrms I rms cos(θ ) − Vrms I rms cos( 2ωt + θ )
(24)
0x10 3880
0xA D055
The apparent power is defined as Vrms × Irms. This expression is
independent from the phase angle between the current and
the voltage.
0x5 682B
0x0 0000
0x000
0x7FF
0x800
APPARENT POWER
CALIBRATION RANGE,
VOLTAGE AND CURRENT
CHANNEL INPUTS: 0.5V/GAIN
APPARENT POWER
SIGNAL (P)
IRMS
CURRENT RMS SIGNAL – i(t)
MULTIPLIER
0xA D055
0x00
VAGAIN
0x00
Figure 64. Apparent Power Signal Processing
04481-A-065
VOLTAGE RMS SIGNAL– v(t)
0x17 D338
Figure 65. Apparent Power Calculation Output Range
Apparent Power Offset Calibration
0x1C 82B3
VRMS
04481-A-066
{VAGAIN[11:0]}
Figure 64 illustrates the signal processing in each phase for the
calculation of the apparent power in the ADE7763.
Each rms measurement includes an offset compensation
register to calibrate and eliminate the dc component in the rms
value—see the Channel 1 RMS Calculation and Channel 2 RMS
Calculation sections. The Channel 1 and Channel 2 rms values
are then multiplied together in the apparent power signal
processing. Because no additional offsets are created in the
multiplication of the rms values, there is no specific offset
compensation in the apparent power signal processing. The
offset compensation of the apparent power measurement is
done by calibrating each individual rms measurement.
Rev. A | Page 31 of 56
ADE7763
VAENERGY[23:0]
APPARENT ENERGY CALCULATION
23
0
The apparent energy is given as the integral of the
apparent power.
48
The ADE7763 achieves the integration of the apparent power
signal by continuously accumulating the apparent power signal
in an internal 49-bit register. The apparent energy register
(VAENERGY[23:0]) represents the upper 24 bits of this internal
register. This discrete time accumulation or summation is
equivalent to integration in continuous time. Equation 29
expresses this relationship.
APPARENT
POWER
48
+
0
+
ACTIVE POWER
SIGNAL = P
∞
∑
%
VADIV
(27)
T
where:
n is the discrete number of time samples.
T is the time sample period.
The discrete time sample period (T) for the accumulation
register is 1.1 µs (4/CLKIN).
APPARENT POWER IS
ACCUMULATED (INTEGRATED) IN
THE APPARENT ENERGY REGISTER
04481-A-067
⎧⎪
⎫⎪
Apparent Energy = Lim ⎨
Apparent Power ( nT ) × T ⎬
T →0 ⎪
⎪⎭
⎩ n =0
0
(26)
TIME (nT)
Figure 66. Apparent Energy Calculation
Figure 66 shows this discrete time integration or accumulation.
The apparent power signal is continuously added to the internal
register. This addition is a signed addition, even if the apparent
energy always remains positive in theory.
The 49 bits of the internal register are divided by VADIV. If the
value in the VADIV register is 0, then the internal active energy
register is divided by 1. VADIV is an 8-bit, unsigned register.
The upper 24 bits are then written in the 24-bit apparent energy
register (VAENERGY[23:0]). RVAENERGY register (24 bits
long) is provided to read the apparent energy. This register is
reset to 0 after a read operation.
Figure 67 shows this apparent energy accumulation for fullscale signals (sinusoidal) on the analog inputs. The three curves
illustrate the minimum time for the energy register to roll over
when the VAGAIN registers content is equal to 0x7FF, 0x000,
and 0x800. The VAGAIN register is used to carry out an
apparent power calibration. As shown in the figure, the fastest
integration time occurs when the VAGAIN register is set to
maximum full scale, i.e., 0x7FF.
VAENERGY[23:0]
0xFF FFFF
VAGAIN = 0x7FF
VAGAIN = 0x000
VAGAIN = 0x800
0x80 0000
0x40 0000
0x20 0000
0x00 0000
6.26
12.52
18.78
25.04
TIME
(minutes)
04481-A-068
∫
Apparent Energy = Apparent Power (t ) dt
Figure 67. Energy Register Rollover Time for Full-Scale Power
(Maximum and Minimum Power Gain)
Note that the apparent energy register is unsigned—see Figure
67. By using the interrupt enable register, the ADE7763 can be
configured to issue an interrupt (IRQ) when the apparent energy
register is more than half full or when an overflow occurs. The
half full interrupt for the unsigned apparent energy register is
based on 24 bits, as opposed to 23 bits for the signed active
energy register.
Rev. A | Page 32 of 56
ADE7763
Integration Times under Steady Load
register for an integral number of half cycles, as shown in
Figure 68. The line apparent energy accumulation mode is
always active.
As mentioned in the last section, the discrete time sample
period (T) for the accumulation register is 1.1 µs (4/CLKIN).
With full-scale sinusoidal signals on the analog inputs and the
VAGAIN register set to 0x000, the average word value from the
apparent power stage is 0xA D055. The maximum value that
can be stored in the apparent energy register before it overflows
is 224 or 0xFF FFFF. The average word value is added to the
internal register, which can store 248 or 0xFFFF FFFF FFFF
before it overflows. Therefore, the integration time under these
conditions with VADIV = 0 is calculated as follows:
Time =
0xFFFF FFFF FFFF
× 1.2 µs = 888 s = 12.52 min (28)
0xAD055
When VADIV is set to a value other than 0, the integration time
varies, as shown in Equation 29.
Time = TimeWDIV = 0 × VADIV
(29)
LINE APPARENT ENERGY ACCUMULATION
The number of half line cycles is specified in the LINECYC
register, which is an unsigned, 16-bit register. The ADE7763 can
accumulate apparent power for up to 65,535 combined half
cycles. Because the apparent power is integrated on the same
integral number of line cycles as the line active energy register,
these two values can be easily compared. The active and apparent
energies are calculated more accurately because of this precise
timing control. At the end of an energy calibration cycle, the
CYCEND flag in the interrupt status register is set. If the
CYCEND mask bit in the interrupt mask register is enabled, the
IRQ output also will go active low. Thus, the IRQ line can also
be used to signal the end of a calibration.
The line apparent energy accumulation uses the same signal path
as the apparent energy accumulation. The LSB size of these two
registers is equivalent.
The ADE7763 is designed with a special apparent energy
accumulation mode, which simplifies the calibration process.
By using the on-chip zero-crossing detection, the ADE7763
accumulates the apparent power signal in the LVAENERGY
+
+
48
LVAENERGY REGISTER IS
UPDATED EVERY LINECYC
ZERO CROSSINGS WITH THE
TOTAL APPARENT ENERGY
DURING THAT DURATION
VADIV[7:0]
LPF1
FROM
CHANNEL 2
ADC
ZERO-CROSSING
DETECTION
0
%
CALIBRATION
CONTROL
23
0
LVAENERGY[23:0]
LINECYC[15:0]
Figure 68. Apparent Energy Calibration
Rev. A | Page 33 of 56
04481-A-069
APPARENT
POWER
ADE7763
ENERGIES SCALING
The ADE7763 provides measurements of active and apparent
energies. These measurements do not have the same scaling and
therefore cannot be compared directly to each other.
used to calibrate the VA, then additional code must be written
in a microprocessor to produce a pulsed output for this
quantity. Otherwise, VA calibration requires an accurate source.
Table 7. Energies Scaling
The ADE7763 provides a line cycle accumulation mode for
calibration using an accurate source. In this method, the active
energy accumulation rate is adjusted to produce a desired CF
frequency. The benefit of using this mode is that the effect of the
ripple noise on the active energy is eliminated. Up to 65,535 half
line cycles can be accumulated, therefore providing a stable
energy value to average. The accumulation time is calculated
from the line cycle period, measured by the period register, and
the number of half line cycles in the accumulation, fixed by the
LINECYC register.
PF = 0
Wh × 0.707
Wh × 0.848
0
Wh × 0.848
Wh × 0.707
Wh × 0.848
0
Wh × 0.848
Wh × 0.707
Wh × 0.827
0
Wh × 0.827
Wh × 0.707
Wh × 0.827
0
Wh × 0.827
CALIBRATING AN ENERGY METER
The ADE7763 provides gain and offset compensation for active
and apparent energy calibration. Its phase compensation corrects
phase error in active and apparent energy. If a shunt is used,
offset and phase calibration may not be required. A reference
meter or an accurate source can be used to calibrate
the ADE7763.
Current and voltage rms offset calibration removes apparent
energy offset. A gain calibration is also provided for apparent
energy. Figure 70 shows an optimized calibration flow for active
energy, rms, and apparent energy.
Active and apparent energy gain calibrations can take place
concurrently, with a read of the accumulated apparent energy
register following that of the accumulated active energy register.
Figure 69 shows the calibration flow for the active energy
portion of the ADE7763.
WATT GAIN CALIBRATION
When using a reference meter, the ADE7763 calibration output
frequency, CF, is adjusted to match the frequency output of the
reference meter. A pulse output is only provided for the active
energy measurement in the ADE7763. If a reference meter is
WATT/VA GAIN CALIBRATION
RMS CALIBRATION
WATT OFFSET CALIBRATION
PHASE CALIBRATION
Figure 69. Active Energy Calibration
WATT OFFSET CALIBRATION
Figure 70. Apparent and Active Energy Calibration
Rev. A | Page 34 of 56
PHASE CALIBRATION
04481-A-083
PF = 0.707
04481-A-084
PF = 1
Integrator on at 50 Hz
Active
Wh
Apparent
Wh × 0.848
Integrator off at 50 Hz
Active
Wh
Apparent
Wh × 0.848
Integrator on at 60 Hz
Active
Wh
Apparent
Wh × 0.827
Integrator off at 60 Hz
Active
Wh
Apparent
Wh × 0.827
ADE7763
Watt Gain
The first step of calibrating the gain is to define the line voltage,
the base current, and the maximum current for the meter. A
meter constant, such as 3200 imp/kWh or 3.2 imp/Wh, needs to
be determined for CF. Note that the line voltage and the
maximum current scale to half of their respective analog input
ranges in this example.
The WGAIN register is used to finely calibrate each meter. Calibrating the WGAIN register changes both CF and AENERGY for
a given load condition.
WGAIN ⎞
AENERGYexpected = AENERGYnominal × ⎛⎜1 +
⎟
12
⎝
CFexpected (Hz) = CFnominal ×
The expected CF in Hz is
CFexpected (Hz) =
MeterConst ant (imp/Wh ) × Load(W)
3600 s/h
× cos(ϕ)
(30)
ϕ is the angle between I and V.
cos (ϕ) is the power factor.
The ratio of active energy LSBs per CF pulse is adjusted using
the CFNUM, CFDEN, and WDIV registers.
LAENERGY
(CFNUM + 1)
× WDIV ×
AccumulationTime(s)
(CFDEN + 1)
(31)
The relationship between watt-hours accumulated and the
quantity read from AENERGY can be determined from the
amount of active energy accumulated over time with a
given load:
Wh
LSB =
Load(W) × Accumulation Time(s)
LAENERGY × 3600 s/h
(32)
where Accumulation Time can be determined from the value in
the line period and the number of half line cycles fixed in the
LINECYC register.
Accumulation time(s) =
LINECYC IB × Line Period(s)
2
8
CLKIN
(CFNUM + 1)
WGAIN ⎞
× ⎛⎜1 +
⎟
(CFDEN + 1) ⎝
2 12 ⎠
The steps of designing and calibrating the active energy portion
of a meter with either a reference meter or an accurate source
are outlined in the following examples. The specifications for
this example are
Meter Constant:
Base Current:
Maximum Current:
Line Voltage:
Line Frequency:
The expected CF output for this meter with the base current
applied is 1.9556 Hz using Equation 30.
CFIB(expected)(Hz) =
3.200 imp/Wh × 10 A × 220 V
3600 s/h
(34)
(35)
In a meter design, WDIV, CFNUM, and CFDEN should be kept
constant across all meters to ensure that the Wh/LSB constant is
maintained. Leaving WDIV at its default value of 0 ensures
maximum resolution. The WDIV register is not included in the
CF signal chain, so it does not affect the frequency pulse output.
MeterConstant(imp/Wh) = 3.2
Ib = 10 A
IMAX = 60 A
Vnominal = 220 V
fl = 50 Hz
The first step in calibration with either a reference meter or an
accurate source is to calculate the CF denominator, CFDEN.
This is done by comparing the expected CF pulse output to the
nominal CF output with the default CFDEN = 0x3F and
CFNUM = 0x3F when the base current is applied.
(33)
The AENERGY Wh/LSB ratio can also be expressed in terms of
the meter constant:
(CFNUM + 1)
× WDIV
(CFDEN + 1)
Wh
=
LSB MeterConstant (imp/Wh)
(36)
When calibrating with a reference meter, WGAIN is adjusted
until CF matches the reference meter pulse output. If an
accurate source is used to calibrate, WGAIN will be modified
until the active energy accumulation rate yields the expected CF
pulse rate.
The line period can be determined from the period register:
Line Period(s) = PERIOD ×
⎠
(37)
where:
CFexpected =
2
× cos(ϕ) = 1.9556 Hz
Alternatively, CFexpected can be measured from a reference meter
pulse output.
CFexpected(Hz) = CFref
(38)
The maximum CF frequency measured without any frequency
division and with ac inputs at full scale is 23 kHz. For this
example, the nominal CF with the test current, Ib, applied is
958 Hz. In this example the line voltage and maximum current
scale half of their respective analog input ranges. The line
voltage and maximum current should not be fixed at the
maximum analog inputs to account for occurrences such as
spikes on the line.
Rev. A | Page 35 of 56
ADE7763
CFnominal(Hz) = 23 kHz × 1 2 × 1 2 ×
I
I MAX
(39)
CFIB(nominal)(Hz) = 23 kHz × 1 2 × 1 2 × 10 60 = 958 Hz
The nominal CF on a sample set of meters should be measured
using the default CFDEN, CFNUM, and WDIV to ensure that
the best CFDEN is chosen for the design.
With the CFNUM register set to 0, CFDEN is calculated to be
489 for the example meter:
⎛ CFIB(nominal )
CFDEN = INT ⎜
⎜ CFIB(expected )
⎝
⎞
⎟ −1
⎟
⎠
For this example:
Meter Constant:
MeterConstant(imp/Wh) = 3.2
CF Numerator:
CFNUM = 0
CF Denominator:
CFDEN = 489
%ERROR Measured at Base Current:
%ERRORCF(IB) = −3.07%
One LSB change in WGAIN changes the active energy registers
and CF by 0.0244%. WGAIN is a signed, twos complement
register and can correct up to a 50% error. Assuming a −3.07%
error, WGAIN is 126:
⎛ % ERRORCF (IB )
WGAIN = INT ⎜⎜ −
0.0244%
⎝
(40)
958 ⎞
CFDEN = INT ⎛⎜
⎟ − 1 = (490 − 1) = 489
⎝ 1.9556 ⎠
When CF is calibrated, the AENERGY register has the same
Wh/LSB constant from meter to meter if the meter constant,
WDIV, and the CFNUM/CFDEN ratio remain the same. The
Wh/LSB ratio for this meter is 6.378 × 10−4 using Equation 35
with WDIV at the default value.
Calibrating Watt Gain Using a Reference Meter Example
The CFDEN and CFNUM values for the design should be
written to their respective registers before beginning the
calibration steps shown in Figure 71. When using a reference
meter, the percent error in CF is measured by comparing the CF
output of the ADE7763 meter with the pulse output of the
reference meter, using the same test conditions for both meters.
Equation 41 defines the percent error with respect to the pulse
outputs of both meters (using the base current, Ib):
CFIB − CFref ( IB )
CFref ( IB)
× 100
(41)
CALCULATE CFDEN VALUE FOR DESIGN
WRITE CFDEN VALUE TO CFDEN REGISTER
ADDR. 0x15 = CFDEN
SET ITEST = Ib, VTEST = VNOM, PF = 1
MEASURE THE % ERROR BETWEEN
THE CF OUTPUT AND THE
REFERENCE METER OUTPUT
WRITE WGAIN VALUE TO THE WGAIN
REGISTER: ADDR. 0x12
04481-A-085
CALCULATE WGAIN. SEE EQUATION 42.
Figure 71. Calibrating Watt Gain Using a Reference Meter
(42)
⎛ −3.07% ⎞
WGAIN = INT ⎜ −
⎟ = 126
⎝ 0.0244% ⎠
This value for CFDEN should be loaded into each meter before
calibration. The WGAIN register can then be used to finely
calibrate the CF output. The following sections explain how to
calibrate a meter based on ADE7763 when using a reference
meter or an accurate source.
%ERRORCF(IB) =
⎞
⎟⎟
⎠
(CFNUM + 1)
× WDIV
(CFDEN + 1)
Wh
=
LSB MeterConstant (imp/Wh)
Wh
1
(490 + 1)
1
−4
LSB = 3.200 imp/Wh = 490 × 3.2 = 6.378 × 10
Calibrating Watt Gain Using an Accurate Source Example
The CFDEN value calculated using Equation 40 should be
written to the CFDEN register before beginning calibration and
zero should be written to the CFNUM register. Enable the line
accumulation mode and the line accumulation interrupt. Then,
write the number of half line cycles for the energy accumulation
to the LINECYC register to set the accumulation time. Reset the
interrupt status register and wait for the line cycle accumulation
interrupt. The first line cycle accumulation results might not
use the accumulation time set by the LINECYC register and,
therefore, should be discarded. After resetting the interrupt
status register, the following line cycle readings will be valid.
When LINECYC half line cycles have elapsed, the IRQ pin goes
active low and the nominal LAENERGY with the test current
applied can be read. This LAENERGY value is compared to the
expected LAENERGY value to determine the WGAIN value. If
apparent energy gain calibration is performed at the same time,
LVAENERGY can be read directly after LAENERGY. Both
registers should be read before the next interrupt is issued on
the IRQ pin. Figure 72 details steps to calibrate the watt gain
using an accurate source.
Rev. A | Page 36 of 56
ADE7763
CALCULATE CFDEN VALUE FOR DESIGN
LAENERGYIB(expected) =
⎛
⎞
⎜
⎟
CF
×
Accumulati
on
Time
(s)
⎜ IB(expected )
⎟
INT ⎜
⎟
CFNUM + 1
⎜
⎟
× WDIV
⎜
⎟
CFDEN + 1
⎝
⎠
WRITE CFDEN VALUE TO CFDEN REGISTER
ADDR. 0x15 = CFDEN
SET ITEST = Ib, VTEST = VNOM, PF = 1
where CFIB(expected) (Hz) is calculated from Equation 30,
accumulation time is calculated from Equation 33, and the line
period is determined from the period register according to
Equation 34.
SET HALF LINE CYCLES FOR ACCUMULATION
IN LINECYC REGISTER ADDR. 0x1C
SET MODE FOR LINE CYCLE
ACCUMULATION ADDR. 0x09 = 0x0080
For this example:
ENABLE LINE CYCLE ACCUMULATION
INTERRUPT ADDR. 0x0A = 0x04
Meter Constant:
MeterConstant(imp/Wh) = 3.2
Test Current:
Ib = 10 A
Line Voltage:
Vnominal = 220 V
Line Frequency:
fl = 50 Hz
Half Line Cycles:
LINECYCIB = 2000
CF Numerator:
CFNUM = 0
CF Denominator:
CFDEN = 489
Energy Reading at Base Current:
LAENERGYIB (nominal) = 17174
Period Register Reading:
PERIOD = 8959
Clock Frequency:
CLKIN = 3.579545 MHz
RESET THE INTERRUPT STATUS
READ REGISTER ADDR. 0x0C
INTERRUPT?
NO
YES
RESET THE INTERRUPT STATUS
READ REGISTER ADDR. 0x0C
INTERRUPT?
CFexpected is calculated to be 1.9556 Hz according to Equation 30.
LAENERGYexpected is calculated to be 19186 using Equation 44.
NO
CFIB(expected)(Hz) =
3.200 imp/Wh × 220 V × 10 A
YES
READ LINE ACCUMULATION ENERGY
ADDR. 0x04
3600 s/h
× cos(ϕ) = 1.9556 Hz
LAENERGYIB(expected) =
INT
04481-A-086
CALCULATE WGAIN. SEE EQUATION 43.
WRITE WGAIN VALUE TO THE WGAIN
REGISTER: ADDR. 0x12
(44)
Figure 72. Calibrating Watt Gain Using an Accurate Source
Equation 43 describes the relationship between the expected
LAENERGY value and the LAENERGY measured in the test
condition:
⎛ ⎛ LAENERGYIB (expected )
⎞
⎞
WGAIN = INT ⎜ ⎜
− 1⎟ × 212 ⎟ (43)
⎜ ⎜ LAENERGYIB ( nominal )
⎟
⎟
⎠
⎝⎝
⎠
The nominal LAENERGY reading, LAENERGYIB(nominal), is the
LAENERGY reading with the test current applied. The expected
LAENERGY reading is calculated from the following equation:
Rev. A | Page 37 of 56
⎛
⎞
⎜
⎟
CF
×
LINECYC
×
PERIOD
×
CLKIN
/
2
8
/
⎜ IB(expected )
⎟
IB
⎜
⎟
CFNUM + 1
⎜
⎟
× WDIV
⎜
⎟
CFDEN
+
1
⎝
⎠
LAENERGYIB(expected) =
⎞
⎛
⎜
6 ⎟
1
.
9556
2000
/
2
8959
8
/(
3
.
579545
10
)
×
×
×
×
⎟1 =
INT ⎜⎜
⎟
1
⎟
⎜
489 + 1
⎠
⎝
INT(19186.4) = 19186
ADE7763
WGAIN is calculated to be 480 using Equation 43.
SET ITEST = IMIN, VTEST = VNOM, PF = 1
⎛ 19186
⎞
− 1⎞⎟ × 2 12 ⎟ = 480
WGAIN = INT ⎜ ⎛⎜
17174
⎝
⎠
⎝
⎠
MEASURE THE % ERROR BETWEEN THE
CF OUTPUT AND THE REFERENCE METER
OUTPUT, AND THE LOAD IN WATTS
Note that WGAIN is a signed, twos complement register.
With WDIV and CFNUM set to 0, LAENERGY can be
expressed as
WRITE APOS VALUE TO THE APOS
REGISTER: ADDR. 0x11
LAENERGYIB(expected) =
INT (CFIB(expected ) × LINECYC IB / 2 × PERIOD × 8 / CLKIN × (CFDEN + 1))
Wh
Figure 73. Calibrating Watt Offset Using a Reference Meter
For this example:
1
(489 + 1)
−4
LSB = 3.200 imp/Wh = 6.378 × 10
Watt Offset
Using Equation 45, APOS is −522 for this example.
Offset calibration allows outstanding performance over a wide
dynamic range, for example, 1000:1. To do this calibration two
measurements are needed at unity power factor, one at Ib and
the other at the lowest current to be corrected. Either calibration frequency or line cycle accumulation measurements can be
used to determine the energy offset. Gain calibration should be
performed prior to offset calibration.
CF Absolute Error = CFIMIN(nominal) − CFIMIN(expected)
AENERGY Error Rate × 2 35
CLKIN
(45)
The AENERGY registers update at a rate of CLKIN/4. The twos
complement APOS register provides a fine adjustment to the
active power calculation. It represents a fixed amount of power
offset to be adjusted every CLKIN/4. The 8 LSBs of the APOS
register are fractional such that one LSB of APOS represents
1/256 of the least significant bit of the internal active energy
register. Therefore, one LSB of the APOS register represents 2−33
of the AENERGY[23:0] active energy register.
(46)
CF Absolute Error =
(%ERRORCF(IMIN)) × WIMIN ×
MeterConstant (imp/Wh)
3600
(47)
CF Absolute Error =
⎛ 1.3% ⎞ × 9.6 × 3.200 = 0.000110933 Hz
⎟
⎜
3600
⎝ 100 ⎠
Offset calibration is performed by determining the active energy
error rate. After determining the active energy error rate, calculate the value to write to the APOS register to correct the offset.
APOS = −
MeterConstant(imp/Wh) = 3.2
IMIN = 40 mA
WIMIN = 9.6 W
%ERRORCF(IMIN) = 1.3%
CFNUM = 0
CDEN = 489
CKIN = 3.579545 MHz
Meter Constant:
Minimum Current:
Load at Minimum Current:
CF Error at Minimum Current:
CF Numerator:
CF Denominator:
Clock Frequency:
The calculated Wh/LSB ratio for the active energy register,
using Equation 35 is 6.378 × 10−4 is
04481-A-087
CALCULATE APOS. SEE EQUATION 45.
Then,
AENERGY Error Rate (LSB/s) =
CFDEN + 1
CF Absolute Error ×
CFNUM + 1
(48)
AENERGY Error Rate (LSB/s) =
490
= 0.05436
0.000110933 ×
1
Using Equation 45, APOS is −522.
See the following sections for steps to determine the active
energy error rate for both line accumulation and reference
meter calibration options.
APOS = −
0.05436 × 2 35
3.579545 × 10 6
= − 522
Calibrating Watt Offset Using a Reference Meter Example
Figure 73 shows the steps involved in calibrating watt offset
with a reference meter.
APOS can be represented as follows with CFNUM and WDIV
set at 0:
APOS =
−
Rev. A | Page 38 of 56
(%ERRORCF ( IMIN ) ) × WIMIN ×
MeterConstant(imp/Wh)
× (CFDEN + 1) × 235
3600
CLKIN
ADE7763
Calibrating Watt Offset with an Accurate Source Example
Figure 74 is the flowchart for watt offset calibration with an
accurate source.
Number of Half Line Cycles used at Minimum Current:
LINECYC(IMIN) = 35700
Active Energy Reading at Minimum Current:
LAENERGYIMIN(nominal) = 1395
SET ITEST = IMIN, VTEST = VNOM, PF = 1
The LAENERGYexpected at IMIN is 1255 using Equation 49.
SET HALF LINE CYCLES FOR ACCUMULATION
IN LINECYC REGISTER ADDR. 0x1C
LAENERGYIMIN(expected) =
⎛I
LINECYCI MIN
INT ⎜⎜ MIN × LAENERGYIB(expected ) ×
LINECYC IB
⎝ IB
SET MODE FOR LINE CYCLE
ACCUMULATION ADDR. 0x09 = 0x0080
LAENERGYIMIN(expected) =
35700 ⎞
0.04
× 19186 ×
INT ⎛⎜
⎟ = INT (1369.80) = 1370
2000 ⎠
⎝ 10
ENABLE LINE CYCLE ACCUMULATION
INTERRUPT ADDR. 0x0A = 0x04
RESET THE INTERRUPT STATUS
READ REGISTER ADDR. 0x0C
INTERRUPT?
where:
LAENERGYIB(expected) is the expected LAENERGY reading at Ib
from the watt gain calibration.
LINECYCIMIN is the number of half line cycles that energy is
accumulated over when measuring at IMIN.
NO
YES
More line cycles could be required at the minimum current to
minimize the effect of quantization error on the offset calibration.
For example, if a test current of 40 mA results in an active energy
accumulation of 113 after 2000 half line cycles, one LSB variation
in this reading represents a 0.8% error. This measurement does
not provide enough resolution to calibrate a <1% offset error.
However, if the active energy is accumulated over 37,500 half
line cycles, one LSB variation results in 0.05% error, reducing the
quantization error.
RESET THE INTERRUPT STATUS
READ REGISTER ADDR. 0x0C
INTERRUPT?
⎞
⎟ (49)
⎟
⎠
NO
YES
READ LINE ACCUMULATION ENERGY
ADDR. 0x04
APOS is −672 using Equations 55 and 49.
CALCULATE APOS. SEE EQUATION 45.
04481-A-088
WRITE APOS VALUE TO THE APOS
REGISTER: ADDR. 0x11
LAENERGY Absolute Error =
LAENERGYIMIN(nominal) − LAENERGYIMIN(expected)
LAENERGY Absolute Error = 1395 − 1370 = 25
(50)
Figure 74. Calibrating Watt Offset with an Accurate Source
AENERGY Error Rate (LSB/s) =
LAENERGY Absolute Error
CLKIN
×
LINECYC / 2
8 × PERIOD
For this example:
Meter Constant:
MeterConstant(imp/Wh) = 3.2
Line Voltage:
Vnominal = 220 V
Line Frequency:
fl = 50 Hz
CF Numerator:
CFNUM = 0
CF Denominator:
CFDEN = 489
Base Current:
Ib = 10 A
Half Line Cycles Used at Base Current:
LINECYC(IB) = 2000
Period Register Reading:
PERIOD = 8959
Clock Frequency:
CLKIN = 3.579545 MHz
Expected LAENERGY Register Value at Base Current
(from the Watt Gain section):
LAENERGYIB(expected) = 19186
Minimum Current:
IMIN = 40 mA
AENERGY Error Rate (LSB/s) =
3.579545 × 10 6
25
×
= 0.069948771
35700 / 2
8 × 8959
APOS = −
APOS = −
Rev. A | Page 39 of 56
AENERGY Error Rate × 2 35
CLKIN
0.069948771 × 2 35
3.579545 × 10 6
= − 672
(51)
ADE7763
Phase Calibration
Calibrating Phase Using a Reference Meter Example
The PHCAL register is provided to remove small phase errors.
The ADE7763 compensates for phase error by inserting a small
time delay or advance on the voltage channel input. Phase leads
up to 1.84° and phase lags up to 0.72° at 50 Hz can be corrected.
The error is determined by measuring the active energy at IB and
two power factors, PF = 1 and PF = 0.5 inductive.
A power factor of 0.5 inductive can be assumed if the pulse
output rate of the reference meter is half of its PF = 1 rate.
Then, the percent error between CF and the pulse output of
the reference meter can be used to perform the preceding
calculations.
SET ITEST = Ib, VTEST = VNOM, PF = 0.5
Some CTs may introduce large phase errors that are beyond the
range of the phase calibration register. In this case, coarse phase
compensation has to be done externally with an analog filter.
MEASURE THE % ERROR BETWEEN
THE CF OUTPUT AND THE
REFERENCE METER OUTPUT
The phase error can be obtained from either CF or LAENERGY
measurements:
LAENERGY IB , PF = 0.5 − LAENERGY IB(expected ) 2
LAENERGY IB (expected ) 2
WRITE PHCAL VALUE TO THE PHCAL
REGISTER: ADDR. 0x10
(52)
04481-A-089
Error =
CALCULATE PHCAL. SEE EQUATION 55.
Figure 75. Calibrating Phase Using a Reference Meter
If watt gain and offset calibration have been performed, there
should be 0% error in CF at unity power factor, and then
Error = %ERRORCF(IB,PF = 0.5)/100
(53)
The phase error is
For this example:
CF %ERROR at PF = 0.5 Inductive: %ERRORCF(IB,PF = 0.5) = 0.215%
PERIOD Register Reading:
PERIOD = 8959
Then PHCAL is 11 using Equations 57 through 59:
⎛ Error ⎞
⎟
⎟
⎝ 3 ⎠
Phase Error (°) = −Arcsin ⎜⎜
Error = 0.215%/100 = 0.00215
(54)
⎛ 0.00215 ⎞
Phase Error (°) = −Arcsin ⎜⎜
⎟ = − 0.07°
3 ⎟⎠
⎝
The relationship between phase error and the PHCAL phase
correction register is
PERIOD ⎞
PHCAL = INT ⎛⎜ Phase Error(°) ×
⎟ + 0x0D
360° ⎠
⎝
8959 ⎞
PHCAL = INT ⎛⎜ − 0.07° ×
⎟ +0x0D = −2 + 13 = 11
360° ⎠
⎝
(55)
PHCAL can be expressed as follows:
The expression for PHCAL can be simplified using the
assumption that at small x
PHCAL =
⎛
⎛ % ERROR × 100 ⎞ PERIOD ⎞
⎟ + 0x0D (58)
INT ⎜⎜ − Arcsin⎜⎜
⎟⎟ ×
2 π ⎟⎠
3
⎠
⎝
⎝
Arcsin(x) ≈ x
The delay introduced in the voltage channel by PHCAL is
Delay = (PHCAL − 0x0D) × 8/CLKIN
(56)
The delay associated with the PHCAL register is a time delay if
PHCAL − 0x0D is positive, but represents a time advance if this
quantity is negative. There is no time delay if PHCAL = 0x0D.
Note that PHCAL is a signed, twos complement register.
Setting the PHCAL register to 11 provides a phase correction
of 0.08° to correct the phase lead:
The phase correction is in the opposite direction of the
phase error.
Phase Correction (°) = − (PHCAL − 0x0D) ×
Phase Correction (°) = − (PHCAL − 0x0D) ×
Phase Correction (°) = − (11 − 0x0D) ×
360°
(57)
PERIOD
Rev. A | Page 40 of 56
360°
PERIOD
360°
= 0.08°
8960
ADE7763
Calibrating Phase with an Accurate Source Example
The error using Equation 52 is
With an accurate source, line cycle accumulation is a good
method of calibrating phase error. The value of LAENERGY
must be obtained at two power factors, PF = 1 and PF = 0.5
inductive.
9613 − 19186
Error =
19186
2 = 0.0021
2
⎛ 0.0021 ⎞
Phase Error (°) = −Arcsin ⎜⎜
⎟ = − 0.07°
3 ⎟⎠
⎝
SET ITEST = Ib, VTEST = VNOM, PF = 0.5
Using Equation 55, PHCAL is 11.
SET HALF LINE CYCLES FOR ACCUMULATION
IN LINECYC REGISTER ADDR. 0x1C
8959 ⎞
PHCAL = INT ⎛⎜ − 0.07° ×
⎟ + 0x0D = − 2 + 13 = 11
360° ⎠
⎝
SET MODE FOR LINE CYCLE
ACCUMULATION ADDR. 0x09 = 0x0080
Note that PHCAL is a signed, twos complement register.
ENABLE LINE CYCLE ACCUMULATION
INTERRUPT ADDR. 0x0A = 0x04
The phase lead is corrected by 0.08 degrees when the PHCAL
register is set to 11:
RESET THE INTERRUPT STATUS
READ REGISTER ADDR. 0x0C
Phase Correction (°) = − (PHCAL − 0x0D) ×
INTERRUPT?
NO
Phase Correction (°) = − (11 − 0x0D) ×
360°
PERIOD
360°
= 0.08°
8960
VRMS and IRMS Calibration
YES
VRMS and IRMS are calculated by squaring the input in a
digital multiplier.
RESET THE INTERRUPT STATUS
READ REGISTER ADDR. 0x0C
v 2 (t ) = 2 V sin(ωt ) × 2 V sin(ωt ) = V 2 − V 2 × cos(2ωt )
INTERRUPT?
NO
(59)
The square of the rms value is extracted from v2(t) by a low-pass
filter. The square root of the output of this low-pass filter gives
the rms value. An offset correction is provided to cancel noise
and offset contributions from the input.
YES
READ LINE ACCUMULATION ENERGY
ADDR. 0x04
There is ripple noise from the 2ω term because the low-pass
filter does not completely attenuate the signal. This noise can be
minimized by synchronizing the rms register readings with the
zero crossing of the voltage signal. The IRQ output can be
configured to indicate the zero crossing of the voltage signal.
WRITE PHCAL VALUE TO THE PHCAL
REGISTER: ADDR. 0x10
04481-A-090
CALCULATE PHCAL. SEE EQUATION 55.
Figure 76. Calibrating Phase with an Accurate Source
For this example:
Meter Constant:
MeterConstant(imp/Wh) = 3.2
Line Voltage:
Vnominal = 220 V
Line Frequency:
fL = 50 Hz
CF Numerator:
CFNUM = 0
CF Denominator:
CFDEN = 489
Base Current:
Ib = 10 A
Half Line Cycles Used at Base Current:
LINECYCIB = 2000
PERIOD Register:
PERIOD = 8959
Expected Line Accumulation at Unity Power Factor (from Watt
Gain section):
LAENERGYIB(expected) = 19186
Active Energy Reading at PF = 0.5 inductive:
LAENERGYIB, PF = 0.5 = 9613
This flowchart demonstrates how VRMS and IRMS readings
are synchronized to the zero crossings of the voltage input.
Rev. A | Page 41 of 56
ADE7763
SET INTERRUPT ENABLE FOR ZERO
CROSSING ADDR. 0x0A = 0x0010
IRMSOS =
RESET THE INTERRUPT STATUS
READ REGISTER ADDR. 0x0C
I 1 2 × IRMS 2 2 − I 2 2 × IRMS 1 2
1
×
32768
I 2 2 − I12
(63)
where IRMS1 and IRMS2 are rms register values without offset
correction for input I1 and I2, respectively.
Apparent Energy
INTERRUPT?
Apparent energy gain calibration is provided for both meter-tometer gain adjustment and for setting the VAh/LSB constant.
NO
VAENERGY =
YES
READ VRMS OR IRMS
ADDR. 0x17; 0x16
04481-A-091
RESET THE INTERRUPT STATUS
READ REGISTER ADDR. 0x0C
VAENERGYinitial ×
Figure 77. Synchronizing VRMS and IRMS Readings with Zero Crossings
Voltage rms compensation is done after the square root.
VRMS = VRMS0 + VRMSOS
(60)
where:
VRMS0 is the rms measurement without offset correction.
VRMS is linear from full-scale to full-scale/20.
To calibrate the offset, two VRMS measurements are required,
for example, at Vnominal and Vnominal/10. Vnominal is set at half of the
full-scale analog input range so that the smallest linear VRMS
reading is at Vnominal/10.
VRMSOS =
V1 × VRMS 2 − V 2 × VRMS1
V 2 − V1
Apparent energy gain calibration should be performed before
rms offset correction to make the most efficient use of the current
test points. Apparent energy gain and watt gain compensation
require testing at Ib, while rms and watt offset correction require
a lower test current. Apparent energy gain calibration can be
done simultaneously with the watt-hour gain calibration
using line cycle accumulation. In this case, LAENERGY and
LVAENERGY, the line cycle accumulation apparent energy
registers, are both read following the line cycle accumulation
interrupt. Figure 78 shows a flowchart for calibrating active and
apparent energy simultaneously.
⎛ ⎛ LVAENERGYIB(expected)
⎞
⎞
− 1⎟ × 212 ⎟
VAGAIN = INT ⎜ ⎜
⎟
⎜ ⎜ LVAENERGYIB(nominal)
⎟
⎠
⎝⎝
⎠
(61)
⎛
⎞
⎜
⎟
Vnominal × I B
INT ⎜
× Accumulation time(s) ⎟
⎜ VAh constant × 3600 s/h
⎟
⎜
⎟
⎝ LSB
⎠
(66)
Current rms compensation is performed before the square root:
where IRMS0 is the rms measurement without offset correction.
The current rms calculation is linear from full scale to full
scale/100.
To calibrate this offset, two IRMS measurements are required,
for example, at Ib and IMAX/50. IMAX is set at half of the full-scale
analog input range so that the smallest linear IRMS reading is at
IMAX/50.
(65)
LVAENERGYIB(expected) =
If the range of the 12-bit, twos complement VRMSOS register is
not enough, use the voltage channel offset register, CH2OS, to
correct the VRMS offset.
(62)
(64)
VADIV is similar to the CFDEN for the watt-hour calibration. It
should be the same across all meters and determines the VAh/LSB
constant. VAGAIN is used to calibrate individual meters.
where VRMS1 and VRMS2 are rms register values without offset
correction for input V1 and V2, respectively.
IRMS2 = IRMS02 + 32768 × IRMSOS
1
VAGAIN ⎞
× ⎛⎜1 +
⎟
212
VADIV ⎝
⎠
The accumulation time is determined from Equation 33, and
the line period can be determined from the period register
according to Equation 34. The VAh represented by the
VAENERGY register is
VAh = VAENERGY × VAh/LSB constant
(67)
The VAh/LSB constant can be verified using this equation:
Rev. A | Page 42 of 56
VAh
LSB constant =
VA ×
Accumulation time(s)
LVAENERGY
3600 (68)
ADE7763
CALCULATE CFDEN VALUE FOR DESIGN
WRITE CFDEN VALUE TO CFDEN REGISTER
ADDR. 0x15 = CFDEN
SET ITEST = Ib, VTEST = VNOM, PF = 1
SET HALF LINE CYCLES FOR ACCUMULATION
IN LINECYC REGISTER ADDR. 0x1C
SET MODE FOR LINE CYCLE
ACCUMULATION ADDR. 0x09 = 0x0080
ENABLE LINE CYCLE ACCUMULATION
INTERRUPT ADDR. 0x0A = 0x04
RESET THE INTERRUPT STATUS
READ REGISTER ADDR. = 0x0C
INTERRUPT?
NO
YES
RESET THE INTERRUPT STATUS
READ REGISTER ADDR. = 0x0C
INTERRUPT?
NO
YES
CALCULATE WGAIN. SEE EQUATION 43.
WRITE WGAIN VALUE TO ADDR. 0x12
CALCULATE VAGAIN. SEE EQUATION 65.
WRITE VGAIN VALUE TO ADDR. 0x1A
04481-A-092
READ LINE ACCUMULATION ENERGY
ACTIVE ENERGY: ADDR. 0x04
APPARENT ENERGY: ADDR. 0x07
Figure 78. Active/Apparent Gain Calibration
CLKIN FREQUENCY
In this data sheet, the characteristics of the ADE7763 are shown
when CLKIN frequency equals 3.579545 MHz. However, the
ADE7763 is designed to have the same accuracy at any CLKIN
frequency within the specified range. If the CLKIN frequency is
not 3.579545 MHz, various timing and filter characteristics will
need to be redefined with the new CLKIN frequency. For
example, the cutoff frequencies of all digital filters, such as
LPF1, LPF2, or HPF1, shift in proportion to the change in
CLKIN frequency according to the following equation:
New Frequency = Original Frequency ×
CLKIN Frequency
3.579545 MHz
(69)
The change in CLKIN frequency does not affect the timing
characteristics of the serial interface because the data transfer is
synchronized with the serial clock signal (SCLK). However, it is
important to observe the read/write timing of the serial data
transfer—see the timing characteristics in Table 2. Table 8 lists
various timing changes that are affected by CLKIN frequency.
Table 8. Frequency Dependencies of the ADE7763 Parameters
Parameter
Nyquist Frequency for CH 1, CH 2 ADCs
PHCAL Resolution (seconds per LSB)
Active Energy Register Update Rate (Hz)
Waveform Sampling Rate (per second)
WAVSEL 1,0 = 0 0
01
10
11
Maximum ZXTOUT Period
Rev. A | Page 43 of 56
CLKIN Dependency
CLKIN/8
4/CLKIN
CLKIN/4
CLKIN/128
CLKIN/256
CLKIN/512
CLKIN/1024
524,288/CLKIN
ADE7763
COMMUNICATION
REGISTER
DIN
The analog and the digital circuit can be suspended separately.
The analog portion can be suspended by setting the ASUSPEND
bit (Bit 4) of the mode register to logic high—see the Mode
Register (0x09) section. In suspend mode, all waveform samples
from the ADCs are set to 0s. The digital circuitry can be halted
by stopping the CLKIN input and maintaining a logic high or
low on the CLKIN pin. The ADE7763 can be reactivated by
restoring the CLKIN input and setting the ASUSPEND bit to
logic low.
DOUT
REGISTER 1
IN
OUT
REGISTER 2
IN
OUT
REGISTER 3
IN
OUT
REGISTER n–1
IN
OUT
REGISTER n
IN
OUT
CHECKSUM REGISTER
The ADE7763 has a checksum register (CHECKSUM[5:0]) to
ensure that the data bits received in the last serial read operation
are not corrupted. The 6-bit checksum register is reset before
the first bit (MSB of the register to be read) is put on the DOUT
pin. During a serial read operation, when each data bit becomes
available upon the rising edge of SCLK, the bit is added to the
checksum register. At the end of the serial read operation, the
content of the checksum register is equal to the sum of all ones
previously read in the register. Using the checksum register, the
user can determine if an error has occurred during the last read
operation. Note that a read to the checksum register also
generates a checksum of the checksum register itself.
The communication register is an 8-bit-wide register. The MSB
determines whether the next data transfer operation is a read or
a write. The 6 LSBs contain the address of the register to be
accessed—see the Communication Register section for a more
detailed description.
Figure 81 and Figure 82 show the data transfer sequences for a
read and write operation, respectively. Upon completion of a
data transfer (read or write), the ADE7763 again enters the
communication mode. A data transfer is complete when the
LSB of the ADE7763 register being addressed (for a write or a
read) is transferred to or from the ADE7763.
CS
SCLK
Figure 79. Checksum Register for Serial Interface Read
COMMUNICATION REGISTER WRITE
DIN
SERIAL INTERFACE
All ADE7763 functionality is accessible via several on-chip
registers—see Figure 80. The contents of these registers can be
updated or read using the on-chip serial interface. After poweron or toggling the RESET pin low and a falling edge on CS, the
ADE7763 is placed in communication mode. In communication mode, the ADE7763 expects a write to its communication
register. The data written to the communication register
determines whether the next data transfer operation is a read or
a write and which register is accessed. Therefore, all data
transfer operations with the ADE7763, whether a read or a
write, must begin with a write to the communication register.
0 0
ADDRESS
DOUT
MULTIBYTE
READ DATA
04481-A-072
CHECKSUM REGISTER ADDR: 0x3E
+
Figure 80. Addressing ADE7763 Registers via the Communication Register
Figure 81. Reading Data from the ADE7763 via the Serial Interface
CS
SCLK
COMMUNICATION REGISTER WRITE
DIN
Rev. A | Page 44 of 56
1 0
ADDRESS
MULTIBYTE
READ DATA
Figure 82. Writing Data to the ADE7763 via the Serial Interface
04481-A-073
+
04481-A-070
CONTENT OF REGISTER (n-bytes)
DOUT
REGISTER
ADDRESS
DECODE
04481-A-071
SUSPENDING FUNCTIONALITY
ADE7763
the register to be written to. The ADE7763 starts shifting in the
register data upon the next falling edge of SCLK. All remaining
bits of register data are shifted in upon the falling edge of
subsequent SCLK pulses—see Figure 83. As explained earlier,
the data write is initiated by a write to the communication
register followed by the data. During a data write operation,
data is transferred to all on-chip registers one byte at a time.
After a byte is transferred into the serial port, there is a finite
time before it is transferred to one of the ADE7763 on-chip
registers. Although another byte transfer to the serial port can
start while the previous byte is being transferred to an on-chip
register, this second byte transfer should not finish until at least
4 µs after the end of the previous byte transfer. This functionality
is expressed in the timing specification t6—see Figure 83. If a
write operation is aborted during a byte transfer (CS is brought
high), then that byte cannot be written to the destination register.
The serial interface of the ADE7763 is made up of four signals:
SCLK, DIN, DOUT, and CS. The serial clock for a data transfer
is applied at the SCLK logic input. This logic input has a Schmitttrigger input structure that allows slow rising and falling clock
edges to be used. All data transfer operations are synchronized
to the serial clock. Data is shifted into the ADE7763 at the DIN
logic input upon the falling edge of SCLK. Data is shifted out of
the ADE7763 at the DOUT logic output upon a rising edge of
SCLK. The CS logic input is the chip-select input. This input is
used when multiple devices share the serial bus. A falling edge
upon CS also resets the serial interface and places the ADE7763
into communication mode. The CS input should be driven low
for the entire data transfer operation. Bringing CS high during a
data transfer operation aborts the transfer and places the serial
bus in a high impedance state. The CS logic input can be tied
low if the ADE7763 is the only device on the serial bus. However,
with CS tied low, all initiated data transfer operations must be
fully completed, i.e., the LSB of each register must be transferred
because there is no other way to bring the ADE7763 into communication mode without resetting the entire device using RESET.
Destination registers can be up to 3 bytes wide—see Table 9,
Table 10, Table 11, Table 12, and Table 13. Therefore the first
byte shifted into the serial port at DIN is transferred to the MSB
(most significant byte) of the destination register. If, for example,
the addressed register is 12 bits wide, a 2-byte data transfer
must take place. Because the data is always assumed to be right
justified, in this case the 4 MSBs of the first byte would be
ignored and the 4 LSBs of the first byte written to the ADE7763
would be the 4 MSBs of the 12-bit word. Figure 84 illustrates
this example.
ADE7763 Serial Write Operation
The serial write sequence takes place as follows. With the
ADE7763 in communication mode (i.e., the CS input logic low),
first a write to the communication register occurs. The MSB of
this byte transfer is a 1, indicating that the data transfer
operation is a write. The LSBs of this byte contain the address of
t8
CS
t6
t3
t7
t7
SCLK
t4
t2
1
DIN
A5
0
A4
t5
A2
A3
A1
DB7
A0
MOST SIGNIFICANT BYTE
COMMAND BYTE
DB0
DB7
DB0
LEAST SIGNIFICANT BYTE
Figure 83. Serial Interface Write Timing
DIN
X
X
X
X
DB11
DB10
DB9
DB8
DB7
MOST SIGNIFICANT BYTE
DB6
DB5
DB4
DB3
DB2
LEAST SIGNIFICANT BYTE
Figure 84. 12-Bit Serial Write Operation
Rev. A | Page 45 of 56
DB1
DB0
04481-A-075
SCLK
04481-A-074
t1
ADE7763
Serial Read Operation
logic output enters a high impedance state upon the falling edge
of the last SCLK pulse. The read operation can be aborted by
bringing the CS logic input high before the data transfer is
complete. The DOUT output enters a high impedance state
upon the rising edge of CS.
During a data read operation from the ADE7763, data is shifted
out at the DOUT logic output upon the rising edge of SCLK. As
is the case with the data write operation, a write to the communication register must precede a data read.
When an ADE7763 register is addressed for a read operation,
the entire contents of that register are transferred to the serial
port. This allows the ADE7763 to modify its on-chip registers
without the risk of corrupting data during a multibyte transfer.
With the ADE7763 in communication mode (CS logic low),
first an 8-bit write to the communication register occurs. The
MSB of this byte transfer is a 0, indicating that the next data
transfer operation is a read. The LSBs of this byte contain the
address of the register that is to be read. The ADE7763 starts
shifting data out of the register upon the next rising edge of
SCLK—see Figure 85. At this point, the DOUT logic output
leaves its high impedance state and starts driving the data bus.
All remaining bits of register data are shifted out upon subsequent SCLK rising edges. The serial interface also enters communication mode as soon as the read is complete. Then, the DOUT
Note that when a read operation follows a write operation, the
read command (i.e., write to communication register) should
not happen for at least 4 µs after the end of the write operation.
If the read command is sent within 4 µs of the write operation,
the last byte of the write operation could be lost. This timing
constraint is given as timing specification t9.
CS
t1
t13
t9
SCLK
0
0
A5
A4
A3
A2
A1
A0
DOUT
DB7
COMMAND BYTE
t12
t11
t11
DB0
MOST SIGNIFICANT BYTE
Figure 85. Serial Interface Read Timing
Rev. A | Page 46 of 56
DB7
DB0
LEAST SIGNIFICANT BYTE
04481-A-076
DIN
t10
ADE7763
REGISTERS
Table 9. Summary of Registers by Address
Address
0x01
Name
WAVEFORM
R/W
R
No. Bits
24
Default
0x0
Type1
S
0x02
AENERGY
R
24
0x0
S
0x03
RAENERGY
R
24
0x0
S
0x04
LAENERGY
R
24
0x0
S
0x05
VAENERGY
R
24
0x0
U
0x06
RVAENERGY
R
24
0x0
U
0x07
LVAENERGY
R
24
0x0
U
0x08
0x09
RESERVED
MODE
R/W
16
0x000C
U
0x0A
IRQEN
R/W
16
0x40
U
0x0B
STATUS
R
16
0x0
U
0x0C
RSTSTATUS
R
16
0x0
U
0x0D
CH1OS
R/W
8
0x00
S*
0x0E
CH2OS
R/W
8
0x0
S*
0x0F
GAIN
R/W
8
0x0
U
0x10
PHCAL
R/W
6
0x0D
S
0x11
APOS
R/W
16
0x0
S
Description
Waveform Register. This read-only register contains the sampled
waveform data from either Channel 1, Channel 2, or the active power
signal. The data source and the length of the waveform registers are
selected by Bits 14 and 13 in the mode register—see the Channel 1
Sampling and Channel 2 Sampling sections.
Active Energy Register. Active power is accumulated (integrated) over
time in this 24-bit, read-only register—see the Energy Calculation
section.
Same as the active energy register, except that the register is reset to 0
following a read operation.
Line Accumulation Active Energy Register. The instantaneous active
power is accumulated in this read-only register over the LINECYC
number of half line cycles.
Apparent Energy Register. Apparent power is accumulated over time in
this read-only register.
Same as the VAENERGY register, except that the register is reset to 0
following a read operation.
Line Accumulation Apparent Energy Register. The instantaneous real
power is accumulated in this read-only register over the LINECYC
number of half line cycles.
Mode Register. This is a 16-bit register through which most of the
ADE7763’s functionality is accessed. Signal sample rates, filter enabling,
and calibration modes are selected by writing to this register. The
contents can be read at any time—see the Mode Register (0X09) section.
Interrupt Enable Register. ADE7763 interrupts can be deactivated at any
time by setting the corresponding bit in this 16-bit enable register to
Logic 0. The status register continues to detect an interrupt event even if
disabled; however, the IRQ output is not activated—see the Interrupts
section.
Interrupt Status Register. This is a 16-bit read-only register that contains
information regarding the source of ADE7763 interrupts—see the
Interrupts section.
Same as the interrupt status register, except that the register contents
are reset to 0 (all flags cleared) after a read operation.
Channel 1 Offset Adjust. Bit 6 is not used. Writing to Bits 0 to 5 allows
offsets on Channel 1 to be removed—see the Analog Inputs and CH1OS
Register sections. Writing Logic 1 to the MSB of this register enables the
digital integrator on Channel 1; writing Logic 0 disables the integrator.
The default value of this bit is 0.
Channel 2 Offset Adjust. Bits 6 and 7 are not used. Writing to Bits 0 to 5 of
this register allows offsets on Channel 2 to be removed—see the Analog
Inputs section. Note that the CH2OS register is inverted. To apply a
positive offset, a negative number is written to this register.
PGA Gain Adjust. This 8-bit register is used to adjust the gain selection for
the PGA in Channels 1 and 2—see the Analog Inputs section.
Phase Calibration Register. The phase relationship between Channel 1
and 2 can be adjusted by writing to this 6-bit register. The valid content
of this twos complement register is between 0x1D to 0x21. At the line
frequency of 60 Hz, this ranges from –2.06° to +0.7°—see the Phase
Compensation section.
Active Power Offset Correction. This 16-bit register allows small offsets in
the active power calculation to be removed—see the Active Power
Calculation section.
Rev. A | Page 47 of 56
ADE7763
Address
0x12
Name
WGAIN
R/W
R/W
No. Bits
12
Default
0x0
Type1
S
0x13
WDIV
R/W
8
0x0
U
0x14
CFNUM
R/W
12
0x3F
U
0x15
CFDEN
R/W
12
0x3F
U
0x16
0x17
0x18
0x19
0x1A
IRMS
VRMS
IRMSOS
VRMSOS
VAGAIN
R
R
R/W
R/W
R/W
24
24
12
12
12
0x0
0x0
0x0
0x0
0x0
U
U
S
S
S
0x1B
VADIV
R/W
8
0x0
U
0x1C
LINECYC
R/W
16
0xFFFF
U
0x1D
ZXTOUT
R/W
12
0xFFF
U
0x1E
SAGCYC
R/W
8
0xFF
U
0x1F
SAGLVL
R/W
8
0x0
U
0x20
IPKLVL
R/W
8
0xFF
U
0x21
VPKLVL
R/W
8
0xFF
U
0x22
IPEAK
R
24
0x0
U
0x23
RSTIPEAK
R
24
0x0
U
0x24
VPEAK
R
24
0x0
U
0x25
RSTVPEAK
R
24
0x0
U
0x26
TEMP
R
8
0x0
S
Description
Power Gain Adjust. This is a 12-bit register. Calibrate the active power
calculation by writing to this register. The calibration range is ±50% of
the nominal full-scale active power. The resolution of the gain adjust is
0.0244%/LSB —see the Calibrating an Energy Meter section.
Active Energy Divider Register. The internal active energy register is
divided by the value of this register before being stored in the AENERGY
register.
CF Frequency Divider Numerator Register. Adjust the output frequency
on the CF pin by writing to this 12-bit read/write register—see the
Energy-to-Frequency Conversion section.
CF Frequency Divider Denominator Register. Adjust the output
frequency on the CF pin by writing to this 12-bit read/write register—see
the Energy-to-Frequency Conversion section.
Channel 1 RMS Value (Current Channel).
Channel 2 RMS Value (Voltage Channel).
Channel 1 RMS Offset Correction Register.
Channel 2 RMS Offset Correction Register.
Apparent Gain Register. Calibrate the apparent power calculation by
writing to this register. The calibration range is 50% of the nominal fullscale real power. The resolution of the gain adjust is 0.02444%/LSB.
Apparent Energy Divider Register. The internal apparent energy register
is divided by the value of this register before being stored in the
VAENERGY register.
Line Cycle Energy Accumulation Mode Line-Cycle Register. This 16-bit
register is used during line cycle energy accumulation mode to set the
number of half line cycles for energy accumulation—see the Line Cycle
Energy Accumulation Mode section.
Zero-Crossing Timeout. If no zero crossings are detected on Channel 2
within the time specified in this 12-bit register, the interrupt request line
(IRQ) will be activated—see the Zero-Crossing Detection section.
Sag Line Cycle Register. This 8-bit register specifies the number of
consecutive line cycles below SAGLVL that is required on Channel 2
before the SAG output is activated—see the Line Voltage Sag Detection
section.
Sag Voltage Level. An 8-bit write to this register determines at what peak
signal level on Channel 2 the SAG pin becomes active. The signal must
remain low for the number of cycles specified in the SAGCYC register
before the SAG pin is activated—see the Line Voltage Sag Detection
section.
Channel 1 Peak Level Threshold (Current Channel). This register sets the
level of current peak detection. If the Channel 1 input exceeds this level,
the PKI flag in the status register is set.
Channel 2 Peak Level Threshold (Voltage Channel). This register sets the
level of voltage peak detection. If the Channel 2 input exceeds this level,
the PKV flag in the status register is set.
Channel 1 Peak Register. The maximum input value of the current
channel, since the last read of the register is stored in this register.
Same as Channel 1 peak register, except that the register contents are
reset to 0 after a read.
Channel 2 Peak Register. The maximum input value of the voltage
channel, since the last read of the register is stored in this register.
Same as Channel 2 peak register, except that the register contents are
reset to 0 after a read.
Temperature Register. This is an 8-bit register that contains the result of
the latest temperature conversion—see the Temperature Measurement
section.
Rev. A | Page 48 of 56
ADE7763
Address
0x27
Name
PERIOD
R/W
R
No. Bits
16
Default
0x0
Type1
U
0x28–
0x3C
0x3D
0x3E
Description
Period of the Channel 2 (Voltage Channel) Input Estimated by ZeroCrossing Processing. The MSB of this register is always zero.
Reserved.
TMODE
CHKSUM
R/W
R
8
6
–
0x0
U
U
0x3F
DIEREV
R
8
–
U
Test Mode Register.
Checksum Register. This 6-bit, read-only register is equal to the sum of all
the ones in the previous reads—see the Serial Read Operation section.
Die Revision Register. This 8-bit, read-only register contains the revision
number of the silicon.
1
Type decoder: U = unsigned, S = signed by twos complement method, and S* = signed by sign magnitude method.
Rev. A | Page 49 of 56
ADE7763
REGISTER DESCRIPTIONS
All ADE7763 functionality is accessed via on-chip registers. Each register is accessed by first writing to the communication register and
then transferring the register data. A full description of the serial interface protocol is given in the Serial Interface section.
COMMUNICATION REGISTER
The communication register is an 8-bit, write-only register that controls the serial data transfer between the ADE7763 and the host
processor. All data transfer operations must begin with a write to the communication register. The data written to the communication
register determines whether the next operation is a read or a write and which register is being accessed. Table 10 outlines the bit
designations for the communication register.
DB7
W/R
DB6
0
DB5
A5
DB4
A4
DB3
A3
DB2
A2
DB1
A1
DB0
A0
Table 10. Communication Register
Bit
Location
0 to 5
Bit
Mnemonic
A0 to A5
6
7
RESERVED
W/R
Description
The 6 LSBs of the communication register specify the register for the data transfer operation. Table 9 lists the
address of each on-chip register.
This bit is unused and should be set to 0.
When this bit is a Logic 1, the data transfer operation immediately following the write to the communication
register is interpreted as a write to the ADE7763. When this bit is a Logic 0, the data transfer operation
immediately following the write to the communication register is interpreted as a read operation.
MODE REGISTER (0x09)
The ADE7763 functionality is configured by writing to the mode register. Table 11 describes the functionality of each bit
in the register.
Table 11.
Bit
Location
0
1
2
3
4
Bit
Mnemonic
DISHPF
DISLPF2
DISCF
DISSAG
ASUSPEND
Default
Value
0
0
1
1
0
5
TEMPSEL
0
6
SWRST
0
7
8
9
10
CYCMODE
DISCH1
DISCH2
SWAP
0
0
0
0
12, 11
DTRT1, 0
00
Description
HPF (high-pass filter) in Channel 1 is disabled when this bit is set.
LPF (low-pass filter) after the multiplier (LPF2) is disabled when this bit is set.
Frequency output CF is disabled when this bit is set.
Line voltage sag detection is disabled when this bit is set.
By setting this bit to Logic 1, both A/D converters can be turned off. During normal operation, this
bit should be left at Logic 0. All digital functionality can be stopped by suspending the clock
signal at CLKIN pin.
Temperature conversion starts when this bit is set to 1. This bit is automatically reset to 0 after the
temperature conversion.
Software Chip Reset. A data transfer should not take place to the ADE7763 for at least 18 µs after
a software reset.
Setting this bit to Logic 1 places the chip in line cycle energy accumulation mode.
ADC 1 (Channel 1) inputs are internally shorted together.
ADC 2 (Channel 2) inputs are internally shorted together.
By setting this bit to Logic 1, the analog inputs V2P and V2N are connected to ADC 1 and the
analog inputs V1P and V1N are connected to ADC 2.
Use these bits to select the waveform register update rate.
DTRT1
DTRT0
Update Rate
0
0
27.9 kSPS (CLKIN/128)
0
1
14 kSPS (CLKIN/256)
1
0
7 kSPS (CLKIN/512)
1
1
3.5 kSPS (CLKIN/1024)
Rev. A | Page 50 of 56
ADE7763
15
Bit
Mnemonic
WAVSEL1, 0
POAM
Default
Value
00
Description
Use these bits to select the source of the sampled data for the waveform register.
0
WAVSEL1, 0
Length
Source
0
0
24 bits, active power signal (output of LPF2)
0
1
Reserved
1
0
24 bits, Channel 1
1
1
24 bits, Channel 2
Writing Logic 1 to this bit allows only positive power to accumulate. The default value of this bit is 0.
15 14 13 12 11 10
0
0
0
0
0
0
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
1
1
0
0
ADDR: 0x09
DISHPF
(DISABLE HPF1 IN CHANNEL 1)
POAM
(POSITIVE ONLY ACCUMULATION)
WAVSEL
(WAVEFORM SELECTION FOR SAMPLE MODE)
00 = LPF2
01 = RESERVED
10 = CH1
11 = CH2
DISLPF2
(DISABLE LPF2 AFTER MULTIPLIER)
DISCF
(DISABLE FREQUENCY OUTPUT CF)
DISSAG
(DISABLE SAG OUTPUT)
DTRT
(WAVEFORM SAMPLES OUTPUT DATA RATE)
00 = 27.9kSPS (CLKIN/128)
01 = 14.4kSPS (CLKIN/256)
10 = 7.2kSPS (CLKIN/512)
11 = 3.6kSPS (CLKIN/1024)
ASUSPEND
(SUSPEND CH1 AND CH2 ADCs)
TEMPSEL
(START TEMPERATURE SENSING)
SWAP
(SWAP CH1 AND CH2 ADCs)
SWRST
(SOFTWARE CHIP RESET)
DISCH2
(SHORT THE ANALOG INPUTS ON CHANNEL 2)
CYCMODE
(LINE CYCLE ENERGY ACCUMULATION MODE)
DISCH1
(SHORT THE ANALOG INPUTS ON CHANNEL 1)
NOTE: REGISTER CONTENTS SHOW POWER-ON DEFAULTS
Figure 86. Mode Register
Rev. A | Page 51 of 56
04481-A-077
Bit
Location
14, 13
ADE7763
INTERRUPT STATUS REGISTER (0x0B),
RESET INTERRUPT STATUS REGISTER (0x0C),
INTERRUPT ENABLE REGISTER (0x0A)
The status register is used by the MCU to determine the source of an interrupt request (IRQ). When an interrupt event occurs, the
corresponding flag in the interrupt status register is set to logic high. If the enable bit for this flag is Logic 1 in the interrupt enable register,
the IRQ logic output will go active low. When the MCU services the interrupt, it must first carry out a read from the interrupt status
register to determine the source of the interrupt.
Table 12.
Interrupt
Flag
AEHF
SAG
CYCEND
3
4
5
6
WSMP
ZX
TEMP
RESET
7
8
9
10
11
12
AEOF
PKV
PKI
VAEHF
VAEOF
ZXTO
13
14
15
PPOS
PNEG
RESERVED
Description
Indicates that an interrupt occurred because the active energy register, AENERGY, is more than half full.
Indicates that an interrupt was caused by a sag on the line voltage.
Indicates the end of energy accumulation over an integral number of half line cycles, as defined by the content
of the LINECYC register—see the Line Cycle Energy Accumulation Mode section.
Indicates that new data is present in the waveform register.
This status bit reflects the status of the ZX logic ouput—see the Zero-Crossing Detection section.
Indicates that a temperature conversion result is available in the temperature register.
Indicates the end of a reset for software and hardware resets. The corresponding enable bit has no function in
the interrupt enable register, i.e., this status bit is set at the end of a reset, but cannot be enabled to cause an
interrupt.
Indicates that the active energy register has overflowed.
Indicates that the waveform sample from Channel 2 has exceeded the VPKLVL value.
Indicates that the waveform sample from Channel 1 has exceeded the IPKLVL value.
Indicates that an interrupt occurred because the apparent energy register, VAENERGY, is more than half full.
Indicates that the apparent energy register has overflowed.
Indicates that an interrupt was caused by a missing zero crossing on the line voltage for a specified number of
line cycles—see the Zero-Crossing Timeout section.
Indicates that the power has gone from negative to positive.
Indicates that the power has gone from positive to negative.
Reserved.
15 14 13 12 11 10
0
0
0
0
0
0
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
ADDR: 0x0A, 0x0B, 0x0C
AEHF
(ACTIVE ENERGY HALF FULL)
RESERVED
PNEG
(POWER POSITIVE TO NEGATIVE)
SAG
(SAG ONLINE VOLTAGE)
PPOS
(POWER NEGATIVE TO POSITIVE)
CYCEND
(END OF LINECYC HALF LINE CYCLES)
WSMP
(WAVEFORM SAMPLES DATA READY)
ZXTO
(ZERO-CROSSING TIMEOUT)
VAEOF
(VAENERGY OVERFLOW)
ZX
(ZERO CROSSING)
TEMP
(TEMPERATURE DATA READY)
VAEHF
(VAENERGY IS HALF FULL)
PKI
(CHANNEL 1 SAMPLE ABOVE IPKLVL)
RESET
(END OF SOFTWARE/HARDWARE RESET)
PKV
(CHANNEL 2 SAMPLE ABOVE VPKLVL)
AEOF
(ACTIVE ENERGY REGISTER OVERFLOW)
Figure 87. Interrupt Status/Interrupt Enable Register
Rev. A | Page 52 of 56
04481-A-079
Bit
Location
0
1
2
ADE7763
CH1OS REGISTER (0x0D)
The CH1OS register is an 8-bit, read/write enabled register. The MSB of this register is used to switch the digital integrator on and off in
Channel 1, and Bits 0 to 5 indicate the amount of offset correction in Channel 1. Table 13 summarizes the function of this register.
Table 13. CH1OS Register
Bit
Mnemonic
OFFSET
6
7
Not Used
INTEGRATOR
Description
The 6 LSBs of the CH1OS register control the amount of dc offset correction in the Channel 1 ADC. The 6-bit
offset correction is sign and magnitude coded. Bits 0 to 4 indicate the magnitude of the offset correction.
Bit 5 shows the sign of the offset correction. A 0 in Bit 5 means the offset correction is positive, and a 1
indicates the offset correction is negative.
This bit is not used.
This bit is used to activate the digital integrator on Channel 1. The digital integrator is switched on by setting
this bit. This bit is set to 0 by default.
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
DIGITAL INTEGRATOR SELECTION
1 = ENABLE
0 = DISABLE
ADDR: 0x0D
SIGN AND MAGNITUDE CODED
OFFSET CORRECTION BITS
NOT USED
Figure 88. Channel 1 Offset Register
Rev. A | Page 53 of 56
04481-A-078
Bit
Location
0 to 5
ADE7763
OUTLINE DIMENSIONS
7.50
7.20
6.90
20
11
1
10
5.60
5.30
8.20
5.00
7.80
7.40
PIN 1
2.00 MAX
0.05 MIN
0.65
BSC
COPLANARITY
0.10
1.85
1.75
1.65
0.38
0.22
0.25
0.09
SEATING
PLANE
8°
4°
0°
0.95
0.75
0.55
COMPLIANT TO JEDEC STANDARDS MO-150AE
Figure 89. 20-Lead Shrink Small Outline Package [SSOP]
(RS-20)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADE7763ARS
ADE7763ARSRL
EVAL-ADE7763EB
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
20-Lead SSOP
20-Lead SSOP
Evaluation Board
Rev. A | Page 54 of 56
Package Option
RS-20
RS-20
ADE7763
NOTES
Rev. A | Page 55 of 56
ADE7763
NOTES
© 2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04481–0–10/04(A)
Rev. A | Page 56 of 56