ETC TS339IN

TS339C,I,M
MICROPOWER QUAD CMOS VOLTAGE COMPARATORS
■ EXTREMELY LOW SUPPLY CURRENT : 9µA
typ / comparator
■ WIDE SINGLE SUPPLY RANGE 3V TO 16V
OR DUAL SUPPLIES (±1.5V TO ±8V)
■ EXTREMELY LOW INPUT BIAS CURRENT :
1pA typ
N
DIP14
(Plastic Package)
■ EXTREMELY LOW INPUT OFFSET CURRENT : 1pA typ
■ INPUT COMMON-MODE VOLTAGE RANGE
INCLUDES GND
■ HIGH INPUT IMPEDANCE : 1012Ω typ
■ FAST RESPONSE TIME : 1.5µs typ for 5mV
overdrive
D
SO14
(Plastic Micropackage)
■ PIN-TO-PIN AND FUNCTIONALLY COMPATIBLE WITH BIPOLAR LM339
DESCRIPTION
The TS339 is a micropower CMOS quad voltage
comparator with extremely low consumption of
9µA typ / comparator (20 times less than bipolar
LM339). Similar performances are offered by the
quad micropower comparator TS3704 with a
push-pull CMOS output.
Thus response times remain similar to the LM339.
P
TSSOP14
(Thin Shrink Small Outline Package)
PIN CONNECTIONS (top view)
ORDER CODE
Output 2
Part
Number
TS339C
TS339I
TS339M
Temperature
Range
0°C, +70°C
-40°C, +125°C
-55°C, +125°C
Package
N
D
P
•
•
•
•
•
•
•
•
•
N = Dual in Line Package (DIP)
D = Small Outline Package (SO) - also available in Tape & Reel (DT)
P = Thin Shrink Small Outline Package (TSSOP) - only available
in Tape & Reel (PT)
January 2002
1
14
Output 3
Output1 2
13
Output 4
12
V CC -
VCC
+
3
Inverting Input 1 4
-
+
11
Non-invertingInput 4
Non-inverting Input 1 5
+
-
10
Inverting Input 4
Non-invertingInput 3
Inverting Input 3
Inverting Input 2
6
-
+
9
Non-invertingInput 2
7
+
-
8
1/6
TS339C,I,M
SCHEMATIC DIAGRAM (for 1/4 TS339)
VCC +
T10
T1
T2
T9
T 17
R1
T 11
T12
Input T3
T18
Input +
T4
Output
T 20
T 13
T8
T19
T5
T7
T 14
T 15
T 16
T6
VCC -
ABSOLUTE MAXIMUM RATINGS
Symbol
+
VCC
Vid
Parameter
Supply Voltage
1)
Differential Input Voltage
2)
3)
Unit
18
V
±18
V
18
V
Vi
Input Voltage
Vo
Output Voltage
18
V
Io
Output Current
20
mA
IF
Forward Current in ESD Protection Diodes on Input 4)
50
mA
Power Dissipation
5)
Tstg
1500
830
710
DIP14
SO14
TSSOP14
pd
1.
2.
3.
Value
Storage Temperature Range
-65 to +150
°C
All voltage values, except differential voltage, are with respect to network ground terminal.
Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
The magnitude of the input and the output voltages must never exceed the magnitude of the possitive supply voltage.
4. Guaranteed by design.
5.
Pd is calculated with T amb = +25°C, Tj = +150°C and R thja = 80°C/W for DIP14 package
= 150°C/W for SO14 package
= 175°C/W for TSSOP14 package
OPERATING CONDITIONS
Symbol
Parameter
VCC+
Supply Voltage
Vicm
Common Mode Input Voltage Range
Operating Free-Air Temperature range
Toper
2/6
TS339C,I
TS339M
TS339C
TS339I
TS339M
Value
Unit
3 to 16
4 to 16
V
0 to VCC+ -1.5
V
0 to +70
-40 to +125
-55 to +125
°C
TS339C,I,M
ELECTRICAL CHARACTERISTICS
VCC+ = 5V, VCC- = 0V, Tamb = 25°C (unless otherwise specified)
Symbol
Min.
Typ.
Max.
Unit
1.4
5
6.5
mV
Vio
Input Offset Voltage
Vic = Vicm min., Vcc+ = 5V to 10V - note 1)
Tmin. ≤ Tamb ≤ Tmax.
Iio
Input Offset Voltage - note 2)
Vic = 2.5V
Tmin. ≤ Tamb ≤ Tmax.
1
Input Bias Current (see note 2)
Vic = 2.5V
Tmin. ≤ Tamb ≤ Tmax.
1
Iib
pA
300
pA
600
V CC+-1.2
V icm
Input Common Mode Voltage Range
Tmin. ≤ Tamb ≤ Tmax
CMR
Common-mode Rejection Ratio
Vic = Vicm min.
75
SVR
Supply Voltage Rejection Ratio
VCC+ = +5V to +10V
85
IOH
High Level Output Voltage
Vid = 1V,VIOH = +5V
Tmin. ≤ Tamb ≤ Tmax.
2
40
1000
nA
VOL
Low Level Output Voltage
Vid = -1V, IOL = 6mA
Tmin. ≤ Tamb ≤ Tmax.
260
400
650
mV
ICC
Supply Current (each comparator)
No load - Outputs low
Tmin. ≤ Tamb ≤ Tmax.
10
20
25
µA
tPLH
tPHL
tf
1.
2.
Parameter
0
0
Response Time Low to High
Vic = 0V, f = 10kHz, RL = 5.1kΩ, CL = 15pF, Overdrive = 5mV
Overdrive = 10mV
Overdrive = 20mV
Overdrive = 40mV
TTL Input
Response Time High to Low
Vic = 0V, f = 10kHz, RL = 5.1kΩ, CL = 15pF, Overdrive = 5mV
Overdrive = 10mV
Overdrive = 20mV
Overdrive = 40mV
TTL Input
Fall time
f = 10kHz, CL = 15pF, R L = 5.1kΩ, Overdrive 50mV
V CC+ -1.5
1.5
1.2
1.1
0.9
0.8
2.5
1.9
1.2
0.8
0.08
25
V
dB
dB
µs
µs
ns
The specified offset voltage is the maximun value required to drive the output up to 4.5V or down to 0.3V.
Maximum values including unavoidable inaccuracies of the industrial test.
3/6
TS339C,I,M
PACKAGE MECHANICAL DATA
14 PINS - PLASTIC DIP
Millimeters
Inches
Dimensions
Min.
a1
B
b
b1
D
E
e
e3
F
i
L
Z
4/6
Typ.
0.51
1.39
Max.
Min.
1.65
0.020
0.055
0.5
0.25
Typ.
0.065
0.020
0.010
20
0.787
8.5
2.54
15.24
0.335
0.100
0.600
7.1
5.1
0.280
0.201
3.3
1.27
Max.
0.130
2.54
0.050
0.100
TS339C,I,M
PACKAGE MECHANICAL DATA
14 PINS - PLASTIC MICROPACKAGE (SO)
G
c1
b1
e
a1
b
A
a2
C
L
s
e3
E
D
M
8
1
7
F
14
Millimeters
Inches
Dimensions
Min.
A
a1
a2
b
b1
C
c1
D (1)
E
e
e3
F (1)
G
L
M
S
Typ.
Max.
Min.
1.75
0.2
1.6
0.46
0.25
0.1
0.35
0.19
Typ.
0.069
0.008
0.063
0.018
0.010
0.004
0.014
0.007
0.5
Max.
0.020
45° (typ.)
8.55
5.8
8.75
6.2
0.336
0.228
1.27
7.62
3.8
4.6
0.5
0.344
0.244
0.050
0.300
4.0
5.3
1.27
0.150
0.181
0.020
0.68
0.157
0.208
0.050
0.027
8° (max.)
Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK.
5/6
TS339C,I,M
PACKAGE MECHANICAL DATA
14 PINS - THIN SHRINK SMALL OUTLINE PACKAGE (TSSOP)
k
c
A
C
SEATING
PLANE
E1
L1
L
0,25 mm
.010 inch
GAGE PLANE
E
A2
7
aaa
C
D
8
e
b
A1
14
1
PIN 1 IDENTIFICATION
Millimeters
Inches
Dimensions
Min.
A
A1
A2
b
c
D
E
E1
e
k
L
L1
aaa
0.05
0.80
0.19
0.09
4.90
4.30
0°
0.450
Typ.
1.00
5.00
6.40
4.40
0.65
0.600
1.00
Max.
Min.
1.20
0.15
1.05
0.30
0.20
5.10
0.01
0.031
0.007
0.003
0.192
4.50
0.169
8°
0.750
0°
0.018
0.100
Typ.
0.039
0.196
0.252
0.173
0.025
0.024
0.039
Max.
0.05
0.006
0.041
0.15
0.012
0.20
0.177
8°
0.030
0.004
Information furni shed is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibili ty for the
consequences of use of such information nor for any infring ement of patents or other right s of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics.
Specifications mention ed in this publ ication are subject to change without notice. This public ation supersedes and replaces all
information previously suppl ied. STMicroelectronics products are not authorized for use as critical components in life suppo rt
devices or systems without express written approval of STMicroelectronics.
 The ST logo is a registered trademark of STMicroelectronics
 2002 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia
Malta - Morocco - Singapore - Spain - Sweden - Swit zerland - United Kingdom - United States
 http://w ww.st.com
6/6