TS3V393C,I,M 3V MICROPOWER DUAL CMOS VOLTAGE COMPARATORS ■ DEDICATED TO 3.3V OR BATTERY SUPPLY (specified at 3V and 5V) ■ EXTREMELY LOW SUPPLY CURRENT : 9µA typ / comparator ■ WIDE SINGLE SUPPLY RANGE 2.7V TO 16V N DIP8 (Plastic Package) ■ EXTREMELY LOW INPUT CURRENT: 1pA typ ■ INPUT COMMON-MODE VOLTAGE RANGE INCLUDES GND ■ FAST RESPONSE TIME : 2.5µs typ for 5mV overdrive D SO8 (Plastic Micropackage) ■ PIN-TO-PIN AND FUNCTIONALLY COMPATIBLE WITH BIPOLAR LM393 DESCRIPTION The TS3V393 is a micropower dual CMOS dual voltage comparator with extremely low consumption of 9µA typ / comparator (20 times less than bipolar LM393). Similar performances are offered by the dual micropower comparator TS3V3702 with a push-pull CMOS output. P TSSOP8 (Thin Shrink Small Outline Package) PIN CONNECTIONS (top view) Thus response times remain similar to the LM393. ORDER CODE Part Number TS3V393I Temperature Range -40°C, +125°C Package N • D • P • Output 1 1 InvertingInput 1 2 - Non-invertingInput 1 3 + VCC - 4 8 V CC + 7 Output2 - 6 InvertingInput 2 + 5 Non-invertingInput 2 N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) P = Thin Shrink Small Outline Package (TSSOP) - only available in Tape & Reel (PT) January 2002 1/7 TS3V393C,I,M SCHEMATIC DIAGRAM (for 1/2 TS3V393) VCC + T 10 T1 T2 T9 T 17 R1 T 11 T12 Input T3 T 18 Input + T4 Output T 20 T 13 T8 T 19 T5 T7 T14 T 15 T 16 T6 VCC - ABSOLUTE MAXIMUM RATINGS Symbol + VCC Supply Voltage 1) Value Unit 18 V ±18 V Vi Input Voltage 3) 18 V Vo Output Voltage 18 V Io Output Current 20 mA IF Forward Current in ESD Protection Diodes on Input 4) 50 mA 1250 710 625 mW -65 to +150 °C Vid pd Tstg 1. 2. 3. 4. Parameter Differential Input Voltage 2) Power Dissipation 5) DIP8 SO8 TSSOP8 Storage Temperature Range All voltage values, except differential voltage, are with respect to network ground terminal. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. The magnitude of the input and the output voltages must never exceed the magnitude of the positive supply voltage. Guaranteed by design. 5. Pd is calculated with T amb = +25°C, Tj = +150°C and R thja = 100°C/W for DIP8 package = 175°C/W for SO8 package = 200°C/W for TSSOP8 package OPERATING CONDITIONS Symbol Parameter VCC+ Supply Voltage Vicm Common Mode Input Voltage Range Toper Operating Free-Air Temperature range 2/7 Value 2.7 to 16 + -1.5 0 to VCC TS3V393I -40 to +125 Unit V V °C TS3V393C,I,M ELECTRICAL CHARACTERISTICS VCC+ = 3V, Vcc- = 0V, Tamb = 25°C (unless otherwise specified) Symbol Parameter Min. Typ. Vio Input Offset Voltage 1) Vic = 1.5V Tmin . ≤ Tamb ≤ Tmax. Iio Input Offset Voltage 2) Vic = 1.5V Tmin . ≤ Tamb ≤ Tmax. 1 Input Bias Current (see note 2) Vic = 1.5V Tmin . ≤ Tamb ≤ Tmax. 1 Iib Max. Unit 5 6.5 mV pA 300 pA 600 VCC+-1.2 Vicm Input Common Mode Voltage Range Tmin . ≤ Tamb ≤ Tmax CMR Common-mode Rejection Ratio Vic = Vicm min. 70 SVR Supply Voltage Rejection Ratio VCC+ = 3V to 5V 70 0 0 VCC+ -1.5 V dB dB IOH High Level Output Current Vid = +1V, V OH = 3V Tmin . ≤ Tamb ≤ Tmax. 2 40 1000 V VOL Low Level Output Voltage Vid = -1V, IOL = +6mA Tmin . ≤ Tamb ≤ Tmax. 400 550 800 mV ICC Supply Current (each comparator) No load - Outputs low Tmin . ≤ Tamb ≤ Tmax. 9 20 25 µA tPLH tPHL Response Time Low to High Vic = 0V, f = 10kHz, RL = 5.1kΩ, CL = 50pF, Overdrive = 5mV TTL Input Response Time High to Low Vic = 0V, f = 10kHz, RL = 5.1kΩ, CL = 50pF, Overdrive = 5mV TTL Input 1.5 0.7 µs 2.5 0.08 µs 1. The specified offset voltage is the maximun value required to drive the output up to 4.5V or down to 0.3V. 2. Maximum values including unavoidable inaccuracies of the industrial test. 3/7 TS3V393C,I,M ELECTRICAL CHARACTERISTICS VCC+ = 5V, Vcc- = 0V, Tamb = 25°C (unless otherwise specified) Symbol Parameter Min. Typ. Max. Unit 5 6.5 mV Vio Input Offset Voltage 1) Vic = 2.5V Tmin . ≤ Tamb ≤ Tmax. 1.4 Iio Input Offset Voltage 2) Vic = 2.5V Tmin . ≤ Tamb ≤ Tmax. 1 Input Bias Current (see note 2) Vic = 2.5V Tmin . ≤ Tamb ≤ Tmax. 1 Iib pA 600 V CC+-1.2 Vicm Input Common Mode Voltage Range Tmin . ≤ Tamb ≤ Tmax CMR Common-mode Rejection Ratio Vic = Vicm min. 71 SVR Supply Voltage Rejection Ratio VCC+ = +5V to +10V 80 0 0 VCC+ -1.5 V dB dB IOH High Level Output Current Vid = 1V, V OH = +5V Tmin . ≤ Tamb ≤ Tmax. 2 40 1000 V VOL Low Level Output Voltage Vid = -1V, IOL = 6mA Tmin . ≤ Tamb ≤ Tmax. 260 400 650 mV ICC Supply Current (each comparator) No load - Outputs low Tmin . ≤ Tamb ≤ Tmax. 10 20 25 µA tPLH tPHL tf Response Time Low to High Vic = 0V, f = 10kHz, RL = 5.1kΩ, CL = 50pF, Overdrive = 5mV Overdrive = 10mV Overdrive = 20mV Overdrive = 40mV TTL Input Response Time High to Low Vic = 0V, f = 10kHz, RL = 5.1kΩ, CL = 50pF, Overdrive = 5mV Overdrive = 10mV Overdrive = 20mV Overdrive = 40mV TTL Input Fall time f = 10kHz, CL = 50pF, R L = 5.1kΩ, Overdrive 50mV 1.5 1.2 1.0 0.8 0.7 2.5 1.9 1.2 0.8 0.08 25 1. The specified offset voltage is the maximun value required to drive the output up to 4.5V or down to 0.3V. 2. Maximum values including unavoidable inaccuracies of the industrial test. 4/7 pA 300 µs µs ns TS3V393C,I,M PACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP Millimeters Inches Dimensions Min. A a1 B b b1 D E e e3 e4 F i L Z Typ. Max. Min. 3.32 0.51 1.15 0.356 0.204 0.020 0.045 0.014 0.008 0.065 0.022 0.012 0.430 0.384 0.313 2.54 7.62 7.62 3.18 Max. 0.131 1.65 0.55 0.304 10.92 9.75 7.95 Typ. 0.100 0.300 0.300 6.6 5.08 3.81 1.52 0.125 0260 0.200 0.150 0.060 5/7 TS3V393C,I,M PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO) s b1 b a1 A a2 C c1 a3 L E e3 D M 5 1 4 F 8 Millimeters Inches Dimensions Min. A a1 a2 a3 b b1 C c1 D E e e3 F L M S 6/7 Typ. Max. 0.65 0.35 0.19 0.25 1.75 0.25 1.65 0.85 0.48 0.25 0.5 4.8 5.8 5.0 6.2 0.1 Min. Typ. Max. 0.026 0.014 0.007 0.010 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.189 0.228 0.197 0.244 0.004 45° (typ.) 1.27 3.81 3.8 0.4 0.050 0.150 4.0 1.27 0.150 0.016 0.6 0.157 0.050 0.024 8° (max.) TS3V393C,I,M PACKAGE MECHANICAL DATA 8 PINS - THIN SHRINK SMALL OUTLINE PACKAGE (TSSOP) k c 0.25mm .010 inch GAGE PLANE L1 L L L1 C SEATING PLANE E1 A E A2 A1 5 4 4 5 D b e 8 1 8 1 PIN 1 IDENTIFICATION Millimeters Inches Dimensions Min. A A1 A2 b c D E E1 e k l L L1 0.05 0.80 0.19 0.09 2.90 4.30 0° 0.50 0.45 Typ. 1.00 3.00 6.40 4.40 0.65 0.60 0.600 1.000 Max. Min. 1.20 0.15 1.05 0.30 0.20 3.10 0.01 0.031 0.007 0.003 0.114 4.50 0.169 8° 0.75 0.75 0° 0.09 0.018 Typ. 0.039 0.118 0.252 0.173 0.025 0.0236 0.024 0.039 Max. 0.05 0.006 0.041 0.15 0.012 0.122 0.177 8° 0.030 0.030 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such infor mation nor for any infring ement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publ ication are subject to change witho ut notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not author ized for use as critical components in life suppo rt devices or systems withou t express written approval of STMicroelectronics. The ST log o is a registered trademark of STMicroelectronics 2002 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States http://ww w.st.com 7/7