AD ADM1170-1AUJZ-RL7

1.6 V to 16.5 V Hot Swap Controller
with Soft Start
ADM1170
FEATURES
GENERAL DESCRIPTION
Controls supply rails from 1.6 V to 16.5 V
Supply voltage range from 2.7 V to 16.5 V
Allows protected board removal and insertion to a live
backplane
External sense resistor provides adjustable analog current
limit with circuit breaker
Soft start controls inrush current profile
Peak fault current limited with fast response
Charge pumped gate drive for external N-FET switch
Automatic retry or latch-off during current fault
Undervoltage lockout
8-lead, TSOT package
The ADM1170 is a hot swap controller that safely enables a
printed circuit board to be removed and inserted to a live
backplane. This is achieved using an external N-channel power
MOSFET with a current control loop that monitors the load
current through a sense resistor. An internal charge pump is
used to enhance the gate of the N-channel FET. When an
overcurrent condition is detected, the gate voltage of the FET is
reduced to limit the current flowing through the sense resistor.
The ADM1170 operates with a supply voltage ranging from
2.7 V to 16.5 V. By using independent SENSE pins from VCC,
the ADM1170 allows for the hot swap of supplies ranging down
to 1.6 V. During an overcurrent condition, the TIMER pin
capacitor determines the amount of time the FET remains at
a current limiting mode of operation until it is shut down. The
ON (ON-CLR) pin is the enable input for the device and can be
used to monitor the input supply voltage. The ADM1170 also
features soft start to provide the user with a capacitor programmable ramping reference to the internal current sense comparator.
This provides a linearly increasing current limit at startup at a
rate set by CSS. This helps to reduce and limit large inrush
currents.
APPLICATIONS
Hot swap board insertion: line cards, raid systems
Industrial high-side switches/circuit breakers
Electronic circuit breakers
This device is available in two options: the ADM1170-1 with
automatic retry for overcurrent fault and the ADM1170-2 with
latch-off for an overcurrent fault. Toggling the ON (ON-CLR)
pin resets a latched fault. The ADM1170 is packaged in an
8-lead TSOT.
FUNCTIONAL BLOCK DIAGRAM
VIN = 1.8V
RSENSE
LONG
Q1
VOUT = 1.8V
CLOAD
SENSE+ SENSE–
LONG
SHORT
VCC
GATE
ADM1170-1
RON1
ON
RON2
SS
CSS
TIMER
GND
CTIMER
GND
GND
LONG
05124-001
VIN = 3.3VAUX
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
ADM1170
TABLE OF CONTENTS
Features .............................................................................................. 1
UVLO........................................................................................... 11
Applications....................................................................................... 1
ON (ON-CLR) Pin..................................................................... 11
General Description ......................................................................... 1
GATE ........................................................................................... 11
Functional Block Diagram .............................................................. 1
Current Limit Function............................................................. 11
Revision History ............................................................................... 2
Calculating the Current Limit .................................................. 11
Specifications..................................................................................... 3
Circuit Breaker Function........................................................... 11
Absolute Maximum Ratings............................................................ 4
Timer Function........................................................................... 12
Thermal Characteristics .............................................................. 4
Power-Up Timing Cycle ............................................................ 12
ESD Caution.................................................................................. 4
Circuit Breaker Timing Cycle................................................... 12
Pin Configurations and Function Descriptions ........................... 5
Automatic Retry or Latched Off............................................... 13
Typical Performance Characteristics ............................................. 6
Soft Start ...................................................................................... 13
Theory of Operation ...................................................................... 11
Outline Dimensions ....................................................................... 14
Overview...................................................................................... 11
Ordering Guide .......................................................................... 14
REVISION HISTORY
7/06—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
ADM1170
SPECIFICATIONS
VCC = 2.7 V to 16.5 V, TA = −40°C to +85°C, typical values at TA = 25°C, unless otherwise noted.
Table 1.
Parameter
VCC PIN
Operating Voltage Range
Supply Current
Undervoltage Lockout
Undervoltage Lockout Hysteresis
ON (ON-CLR) PIN
Input Current
Threshold
Threshold Hysteresis
SENSE PINS (SENSE+/SENSE−)
Hot Swap Operating Range
Input Current
Input Current
Circuit Breaker Limit Voltage
Circuit Breaker Limit Voltage
GATE PIN
Drive Voltage
Symbol
Min
VCC
ICC
VUVLO
VUVLOHYS
2.7
IINON
VON
VONHYST
IINSENSE
IINSENSE
VCB
VCB
2.4
−1
1.22
1.6
−160
5
26
44
Typ
0.65
2.525
40
0
1.3
50
−65
10
50
50
Max
Unit
Conditions
16.5
0.8
2.65
V
mA
V
mV
+1
1.38
μA
V
mV
16.5
+13
15
77
56
V
μA
μA
mV
mV
VSENSE+ = 1.6 V
VSENSE+ ≥ 2.2 V
VCB = (VSENSE+ – VSENSE−), VSENSE+ = 1.6 V
VCB = (VSENSE+ – VSENSE−), VSENSE+ ≥ 2.2 V
VCC rising
ON rising
VGATE
Pull-Up Current
Pull-Down Current
Pull-Down Current
TIMER PIN
Pull-Up Current
4.6
6.0
8.75
7.5
5.56
−6.5
7.5
8
10
9
8
−12
4
25
10
12
12
12
12
−14.5
V
V
V
V
V
μA
mA
mA
VGATE − VCC, VCC = 3.0 V
VGATE − VCC, VCC = 3.3 V
VGATE − VCC, VCC = 5 V
VGATE − VCC, VCC = 12 V
VGATE − VCC, VCC = 15 V
VGATE = 0 V
VGATE = 3 V, VCC = 5 V, ON (ON-CLR) = low
VGATE = 3 V, VCC < UVLO
ITIMERUP
−2
−25
Pull-Down Current
ITIMERDN
−5
−60
2
100
1.3
0.2
−8.5
−100
3.5
μA
μA
μA
μA
V
V
Initial cycle, VTIMER = 1 V
During current fault, VTIMER = 1 V
After Cct breaker tip, VTIMER = 1 V
Normal operation, VTIMER = 1 V
TIMER rising
TIMER falling
Threshold High
Threshold Low
SS PIN
Soft Start Pull-Up Current
Current Setting Gain
Soft Start Completion Voltage
Pull-Down Current
tOFF
Turn-Off Time (TIMER Rise to GATE Fall)
Turn-Off Time (ON Fall to GATE Fall)
Turn-Off Time (VCC Fall to IC Reset)
VTIMERH
VTIMERL
1.22
0.15
10
20
1
50
2
40
40
Rev. 0 | Page 3 of 16
1.38
0.25
μA
V/V
V
μA
μs
μs
μs
VSS/VSENSE
During fault
VTIMER = 0 V to 2 V step, VCC = VON = 5 V
VON = 5 V to 0 V step, VCC = 5 V
VCC = 5 V to 2 V step, VON = 5 V
ADM1170
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
VCC Pin
SENSE+ Pin/SENSE− Pin
SENSE+ Pin − SENSE− Pin
TIMER Pin
ON (ON-CLR) Pin
SS Pin
GATE Pin
Storage Temperature Range
Operating Temperature Range
Lead Temperature (10 sec)
Junction Temperature
Rating
−0.3 V to +20 V
−0.3 V to +20 V
±5 V
−0.3 V to (VCC + 0.3 V)
−0.3 V to +20 V
–0.3 V to (VCC + 0.3 V)
−0.3 V to (VCC + 11 V)
−65°C to +125°C
−40°C to +85°C
300°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL CHARACTERISTICS
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 3. Thermal Resistance
Package Type
8-Lead TSOT
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 4 of 16
θJA
152.9
Unit
°C/W
ADM1170
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
ADM1170-1AUJ
8
VCC
ON 4
5
GATE
8
VCC
GND 2
7 SENSE+
TOP VIEW
SS 3 (Not to Scale) 6 SENSE–
05124-006
7 SENSE+
TOP VIEW
SS 3 (Not to Scale) 6 SENSE–
TIMER 1
GND 2
ON-CLR 4
Figure 2. Pin Configuration, 1AUJ Model
5
GATE
05124-007
TIMER 1
ADM1170-2AUJ
Figure 3. Pin Configuration, 2AUJ Model
Table 4. Pin Function Descriptions
Pin No.
1
Mnemonic
TIMER
2
3
GND
SS
4
ON (ON-CLR)
5
GATE
6, 7
SENSE−, SENSE+
8
VCC
Description
Timer Input Pin. The initial and circuit breaker timing cycles are set by this external capacitor. The initial timing
delay is 272.9 ms/μF, and 21.7 ms/μF for a circuit breaker delay. When the TIMER pin is pulled beyond the
upper threshold, the GATE turns off.
Chip Ground Pin.
Soft Start Pin. An external capacitor between the SS pin and GND sets the ramp rate of the current limit
reference.
Input Pin. The ON (ON-CLR) pin is an input to a comparator that has a low-to-high threshold of 1.3 V with
80 mV hysteresis and a glitch filter. The ADM1170 is reset when the ON (ON-CLR) pin is low. When the ON
(ON-CLR) pin is high, the ADM1170 is enabled. A rising edge on this pin has the added function of clearing a
fault and restarting the device on the latched off model, the ADM1170-2.
Gate Output Pin. An internal charge pump provides a 12 μA pull-up current to drive the gate of an N-channel
MOSFET. In an overcurrent condition, the ADM1170 controls the external FET to maintain a constant load
current.
Current Limit Sense Input Pins. The current limit is set via a sense resistor between the SENSE+ and SENSE−
pins. In an overcurrent condition, the gate of the FET is controlled to maintain the SENSE voltage at 50 mV.
When this limit is reached, the TIMER circuit breaker mode is activated. The circuit breaker limit can be
disabled by connecting the SENSE+ and SENSE− pins together.
Positive Supply Input Pin. The ADM1170 operates between 2.7 V to 16.5 V. An undervoltage lockout (UVLO)
circuit with a glitch filter resets the ADM1170 when the supply voltage drops below the specified UVLO limit.
Rev. 0 | Page 5 of 16
ADM1170
2.65
0.45
2.63
0.40
2.61
0.35
0.30
0.25
0.20
0.15
2.57
2.53
2.51
0.05
2.47
2
4
6
8
10
12
14
16
18
SUPPLY VOLTAGE (V)
VCC FALLING
2.55
2.49
0
VCC RISING
2.59
0.10
0
VCC = 5V
2.45
–50
–25
0
25
50
75
100
125
150
16
18
125
150
TEMPERATURE (°C)
05124-046
UVLO THRESHOLD (V)
0.50
05124-023
SUPPLY CURRENT (mA)
TYPICAL PERFORMANCE CHARACTERISTICS
Figure 7. UVLO Threshold vs. Temperature
Figure 4. Supply Current vs. Supply Voltage (GATE off)
0.8
25
0.7
GATE VOLTAGE (V)
SUPPLY CURRENT (mA)
20
0.6
0.5
0.4
0.3
15
10
0.2
5
0
2
4
6
8
10
12
14
16
18
SUPPLY VOLTAGE (V)
0
05124-024
0
0
2
4
6
8
10
12
14
SUPPLY VOLTAGE (V)
Figure 5. Supply Current vs. Supply Voltage (GATE on)
05124-013
0.1
Figure 8. GATE Voltage vs. Supply Voltage
1.0
25
VCC = 15V
0.9
20
VCC = 12V
GATE VOLTAGE (V)
VCC = 12V
VCC = 15V
0.6
0.5
0.4
VCC = 3V
VCC = 5V
0.3
0.2
15
VCC = 5V
10
VCC = 3V
5
0
–50
–25
0
25
50
75
100
TEMPERATURE (°C)
125
150
0
–50
–25
0
25
50
75
100
TEMPERATURE (°C)
Figure 6. Supply Current vs. Temperature
Figure 9. GATE Voltage vs. Temperature
Rev. 0 | Page 6 of 16
05124-015
0.1
05124-033
SUPPLY CURRENT (mA)
0.8
0.7
10
0
9
–1
8
–2
7
–3
ITIMERUP (µA)
6
5
4
–4
–5
–6
3
–7
2
–8
1
VCC = 5V
–9
0
2
4
6
8
10
12
14
16
18
SUPPLY VOLTAGE (V)
–10
–50
05124-014
0
0
25
50
75
100
125
150
TEMPERATURE (°C)
Figure 10. Delta GATE Voltage vs. Supply Voltage
Figure 13. ITIMERUP (in Initial Cycle) vs. Temperature
10
–20
TA = 25°C
9
VCC = 5V
VCC = 12V
–30
8
–40
7
VCC = 15V
ITIMERUP (µA)
DELTA GATE VOLTAGE (V)
–25
05124-038
DELTA GATE VOLTAGE (V)
ADM1170
6
5
VCC = 3V
4
–50
–60
–70
3
–80
2
–25
0
25
50
75
100
125
150
TEMPERATURE (°C)
–100
05124-016
0
–50
0
2
4
6
8
10
12
14
16
18
SUPPLY VOLTAGE (V)
Figure 11. Delta GATE Voltage vs. Temperature
05124-036
–90
1
Figure 14. ITIMERUP (During Cct Breaker Delay) vs. Supply Voltage
0
–20
TA = 25°C
–1
VCC = 5V
–30
–2
–40
ITIMERUP (µA)
–4
–5
–6
–50
–60
–70
–7
–80
–8
–10
0
2
4
6
8
10
12
14
16
SUPPLY VOLTAGE (V)
18
–100
–50
–25
0
25
50
75
100
125
150
TEMPERATURE (°C)
Figure 12. ITIMERUP (in Initial Cycle) vs. Supply Voltage
Figure 15. ITIMERUP (During Cct Breaker Delay) vs. Temperature
Rev. 0 | Page 7 of 16
05124-039
–90
–9
05124-035
ITIMERUP (µA)
–3
ADM1170
3.0
1.38
TA = 25°C
2.8
VCC = 5V
1.36
TIMER HIGH THRESHOLD (V)
2.6
2.2
2.0
1.8
1.6
1.4
1.34
1.32
1.30
1.28
1.26
0
2
4
6
8
10
12
14
16
18
SUPPLY VOLTAGE (V)
1.22
–50
05124-034
1.0
25
50
75
100
125
150
Figure 19. TIMER High Threshold vs. Temperature
3.0
0.24
VCC = 5V
2.8
TA = 25°C
0.23
TIMER LOW THRESHOLD (V)
2.6
2.4
2.2
2.0
1.8
1.6
1.4
0.22
0.21
0.20
0.19
0.18
0.17
1.2
–25
0
25
50
75
100
125
150
TEMPERATURE (°C)
0.16
05124-037
1.0
–50
0
2
4
6
8
10
12
14
16
18
SUPPLY VOLTAGE (V)
Figure 17. ITIMERDN (in Cool-Off Cycle) vs. Temperature
05124-043
ITIMERDN (µA)
0
TEMPERATURE (°C)
Figure 16. ITIMERDN (in Cool-Off Cycle) vs. Supply Voltage
Figure 20. TIMER Low Threshold vs. Supply Voltage
1.38
0.24
TA = 25°C
VCC = 5V
0.23
TIMER LOW THRESHOLD (V)
1.36
1.34
1.32
1.30
1.28
1.26
1.24
0.22
0.21
0.20
0.19
0.18
0.17
1.22
0
2
4
6
8
10
12
14
16
SUPPLY VOLTAGE (V)
18
0.16
–50
05124-042
TIMER HIGH THRESHOLD (V)
–25
05124-044
1.24
1.2
–25
0
25
50
75
100
125
TEMPERATURE (°C)
Figure 18. TIMER High Threshold vs. Supply Voltage
Figure 21. TIMER Low Threshold vs. Temperature
Rev. 0 | Page 8 of 16
150
05124-045
ITIMERDN (µA)
2.4
ADM1170
1.45
80
TA = 25°C
70
1.35
60
tOFF(ONLOW) (µs)
HIGH THRESHOLD
1.30
LOW THRESHOLD
1.25
1.20
VCC = 15V
50
40
30
1.10
10
0
2
4
6
8
10
12
14
16
18
SUPPLY VOLTAGE (V)
0
–50
–25
0
25
50
75
100
125
150
16
18
TEMPERATURE (°C)
05124-048
VCC = 3V
20
1.05
Figure 25. tOFF(ONLOW) vs. Temperature
Figure 22. ON (ON-CLR) Pin Threshold vs. Supply Voltage
1.45
50
VCC = 5V
49
1.40
48
HIGH THRESHOLD
1.35
47
1.30
VCB (mV)
LOW THRESHOLD
1.25
1.20
46
45
44
43
1.15
42
1.10
41
–25
0
25
50
75
100
125
150
TEMPERATURE (°C)
40
05124-041
1.05
–50
0
2
4
6
8
10
12
14
SUPPLY VOLTAGE (V)
05124-049
ON (ON-CLR) PIN THRESHOLD (V)
VCC = 12V
VCC = 5V
1.15
05124-040
ON (ON-CLR) PIN THRESHOLD (V)
1.40
Figure 26. Cct Breaker Voltage vs. Supply Voltage
Figure 23. ON (ON-CLR) Pin Threshold vs. Temperature
80
50
TA = 25°C
45
70
40
60
VCB (mV)
40
30
30
25
20
15
20
10
10
0
2
4
6
8
10
12
14
SUPPLY VOLTAGE (V)
16
18
0
–50
–25
0
25
50
75
100
125
TEMPERATURE (°C)
Figure 24. tOFF(ONLOW) vs. Supply Voltage
Figure 27. Cct Breaker Voltage vs. Temperature
Rev. 0 | Page 9 of 16
150
05124-021
5
0
05124-047
tOFF(ONLOW) (µs)
35
50
12
–10.4
10
–10.5
SOFT START CURRENT (µA)
GATE CURRENT (mA)
ADM1170
8
6
4
VCC = 3V
–10.6
–10.7
–10.8
VCC = 5V
VCC = 12V
2
–10.9
0
–11.0
–50
2
4
6
8
10
12
14
16
18
SUPPLY VOLTAGE (V)
–25
0
25
50
75
100
125
150
TEMPERATURE (°C)
Figure 28. GATE Current (Down) vs. Supply Voltage
05124-018
0
05124-008
VCC = 15V
Figure 31. Soft Start Current vs. Temperature
–8
50
45
CCT BREAKER VOLTAGE (mV)
GATE CURRENT (µA)
–9
–10
–11
–12
–13
40
35
30
25
20
15
10
2
4
6
8
10
12
14
16
18
SUPPLY VOLTAGE (V)
Figure 29. GATE Current (up) vs. Supply Voltage
–11.2
–11.6
–11.8
VCC = 3V
VCC = 5V
–12.2
VCC = 12V
–12.4
VCC = 15V
–12.8
–13.0
–50
–25
0
25
50
75
100
125
TEMPERATURE (°C)
150
05124-017
GATE CURRENT (µA)
–11.4
–12.6
0
0.2
0.4
0.6
0.8
1.0
SOFT START VOLTAGE (V)
Figure 32. Circuit Breaker Voltage vs. Soft Start Voltage
–11.0
–12.0
0
Figure 30. GATE Current (up) vs. Temperature
Rev. 0 | Page 10 of 16
1.2
05124-020
0
05124-009
5
–14
ADM1170
THEORY OF OPERATION
Many systems require the insertion or removal of circuit boards
to live backplanes. During this event, the supply bypass and holdup capacitors can require substantial transient currents from the
backplane power supply as they charge. These currents can
cause permanent damage to connector pins or undesirable glitches
and resets to the system.
The ADM1170 is intended to control the powering of a system
(on and off) in a controlled manner, allowing the board to be
removed from, or inserted into, a live backplane by protecting it
from excess currents. The ADM1170 can reside either on the
backplane or on the removable board.
OVERVIEW
The ADM1170 operates over a supply range of 2.7 V to 16.5 V.
As the supply voltage is coming up, an undervoltage lockout
circuit checks if sufficient supply voltage is present for proper
operation. During this period, the FET is held off by the GATE
pin being held to GND. When the supply voltage reaches a level
above UVLO and the ON (ON-CLR) pin is high, an initial timing
cycle ensures that the board is fully inserted in the backplane
before turning on the FET. The TIMER pin capacitor sets the
periods for all of the TIMER pin functions. After the initial
timing cycle, the ADM1170 monitors the inrush current
through an external sense resistor. Overcurrent conditions are
actively limited to 50 mV/RSENSE for the circuit breaker timer
limit. The ADM1170-1 automatically retries after a current
limit fault and the ADM1170-2 latches off. The retry duty cycle
on the ADM1170-1 timer function is limited to 3.8% for FET
cooling.
delay time at card insertion. If using a short pin system to
enable the device, a pull-down resistor should be used to hold
the device prior to insertion.
GATE
Gate drive for the external N-channel MOSFET is achieved
using an internal charge pump. The gate driver consists of a
12 μA pull-up from the internal charge pump. There are various
pull-down devices on this pin. At a hotswap condition the board
is hot inserted to the supply bus. During this event, it is possible
for the external FET GATE capacitance to be charged up by the
sudden presence of the supply voltage. This can cause
uncontrolled inrush currents. An internal strong pull-down
circuit holds GATE low while in UVLO. This reduces current
surges at insertion. After the initial timing cycle, the GATE is
then pulled high. During an overcurrent condition, the
ADM1170 servos the GATE pin in an attempt to maintain a
constant current to the load until the circuit breaker timeout
completes. In the event of a timeout, the GATE pin abruptly
shuts down using the 4 mA pull-down device. Care must be
taken not to load the GATE pin resistively because this reduces
the gate drive capability.
CURRENT LIMIT FUNCTION
The ADM1170 features a fast response current control loop that
actively limits the current by reducing the gate voltage of the
external FET. This current is measured by monitoring the
voltage drop across an external sense resistor. The ADM1170
tries to regulate the gate of the FET to achieve a 50 mV voltage
drop across the sense resistor.
UVLO
CALCULATING THE CURRENT LIMIT
If the VCC supply is too low for normal operation, an undervoltage lockout circuit holds the ADM1170 in reset. The GATE
pin is held to GND during this period. When the supply reaches
this UVLO voltage, the ADM1170 starts when the ON (ON-CLR)
pin condition is satisfied.
The sense resistor connected between SENSE+ and the SENSE−
pin is used to determine the nominal fault current limit. This is
given by the following equation:
ON (ON-CLR) PIN
The ON (ON-CLR) pin is the enable pin. It is connected to a
comparator that has a low-to-high threshold of 1.3 V with 80 mV
hysteresis and a glitch filter. The ADM1170 is reset when the
ON (ON-CLR) pin is low. When the ON (ON-CLR) pin is high,
the ADM1170 is enabled. A rising edge on this pin has the
added function of clearing a fault and restarting the device on
the latched off model, the ADM1170-2. A low input on the ON
(ON-CLR) pin turns off the external FET by pulling the GATE
pin to ground and resets the timer. An external resistor divider at
the ON (ON-CLR) pin can be used to program an undervoltage
lockout value higher than the internal UVLO circuit. There is a
glitch filter delay of approximately 3 μs on rising allowing the
addition of an RC filter at the ON (ON-CLR) pin to increase the
ILIMITNOM = VCBNOM/RSENSENOM
(1)
The minimum load current is given by Equation 2
ILIMITMIN = VCBMIN/RSENSEMAX
(2)
The maximum load current is given by Equation 3.
ILIMITMAX = VCBMAX/RSENSEMIN
(3)
For proper operation, the minimum current limit must exceed
the circuit maximum operating load current with margin. The
sense resistor power rating must exceed
(VCBMAX)2/RSENSEMIN
CIRCUIT BREAKER FUNCTION
When the supply experiences a sudden current surge, such as a
low impedance fault on load, the bus supply voltage can drop
significantly to a point where the power to an adjacent card is
affected, potentially causing system malfunctions. The
ADM1170 limits the current drawn by the fault by reducing the
Rev. 0 | Page 11 of 16
ADM1170
gate voltage of the external FET. This minimizes the bus supply
voltage drop caused by the fault and protects neighboring cards.
When the initial cycle ends, a start-up cycle activates and the
GATE pin is pulled high; the TIMER pin continues to pull down.
As the voltage across the sense resistor approaches the current
limit, a timer activates. This timer resets again if the sense
voltage returns below this level. If the sense voltage is any
voltage below 44 mV, the timer is guaranteed to be off. Should
the current continue to increase, the ADM1170 tries to regulate
the gate of the FET to achieve a limit of 50 mV across the sense
resistor. However, if the device is unable to regulate the fault
current and the sense voltage further increases, a larger pulldown, in the order of milliamperes, is enabled to compensate
for fast current surges. If the sense voltage is any voltage greater
than 56 mV, this pull-down is guaranteed to be on. When the
timer expires, the GATE pin shuts down.
VIN
1
VON
2
3
VTIMER
4
VGATE
VOUT
TIMER FUNCTION
INITIAL
CYCLE
NORMAL
CYCLE
05124-002
RESET
MODE
The TIMER pin is responsible for several key functions on the
ADM1170. A capacitor controls the initial power on reset time
and the amount of time an overcurrent condition lasts before
the FET shuts down. On the ADM1170-1, the timer pin also
controls the time between auto retry pulses. There are pull-up
and pull-down currents internally available to control the timer
functions. The voltage on the TIMER pin is compared with two
threshold voltages: COMP1 (0.2 V) and COMP2 (1.3 V). The
four timing currents are listed in Table 5.
START-UP
CYCLE
Figure 33. Power-Up Timing
VIN
60µA
VON
5µA
2µA
Table 5.
Timing Current
Pull-up
Pull-up
Pull-down
Pull-down
VTIMER
Level (μA)
5
60
2
100
100µA
VGATE
VOUT
POWER-UP TIMING CYCLE
This is the end of the first section of the initial cycle. The 100 μA
current source then pulls down the TIMER pin until it reaches
0.2 V at Time Point 4. The initial cycle delay (Time Point 2 to
Time Point 4) relates to CTIMER by equation
tINITIAL = 1.3 × CTIMER/5 μA
(4)
IRSENSE
RESET
MODE
INITIAL START-UP
CYCLE
CYCLE
NORMAL
CYCLE
05124-003
The ADM1170 is in reset when the ON (ON-CLR) pin is held
low. The GATE pin is pulled low and the TIMER pin is pulled
low with a 100 μA pull-down. At Time Point 2 in Figure 33, the
ON (ON-CLR) pin is pulled high. For the device to startup
correctly, the supply voltage must be above UVLO, the ON
(ON-CLR) pin must be above 1.3 V, and the TIMER pin voltage
must be less than 0.2 V. The initial timing cycle begins when these
three conditions are met, and the TIMER pin is pulled high with
5 μA. At Time Point 3, the TIMER reaches the COMP2 threshold.
Figure 34. Power-Up into Capacitor
CIRCUIT BREAKER TIMING CYCLE
When the voltage across the sense resistor exceeds the circuit
breaker trip voltage, the 60 μA timer pull-up current is activated.
If the sense voltage falls below this level before the TIMER pin
reaches 1.3 V, the 60 μA pull-up is disabled and the 2 μA pulldown is enabled. This is likely to happen if the overcurrent fault
is only transient, such as an inrush current. This is shown in
Figure 34. However, if the overcurrent condition is continuous
and the sense voltage remains above the circuit breaker trip
voltage, the 60 μA pull-up remains active. This allows the TIMER
pin to reach the high trip point of 1.3 V and initiate the GATE
shutdown. On the ADM1170-2, the TIMER pin continues pulling
up but switches to the 5 μA pull-up when it reaches the 1.3 V
Rev. 0 | Page 12 of 16
ADM1170
threshold. The device can be reset by toggling the ON-CLR pin
or by manually pulling the TIMER pin low. On the ADM1170-1,
the TIMER pin activates the 2 μA pull-down once the 1.3 V
threshold is reached, and continues to pull down until it reaches
the 0.2 V threshold. At this point, the 100 μA pull-down is
activated and the GATE pin is enabled. The device keeps
retrying in the manner as shown in Figure 35.
The ADM1170-2 model has a latch off system whereby when a
current fault is detected, the GATE is switched off after a time
determined by the timer capacitor (see Figure 36 for details).
Toggling the ON-CLR pin, or pulling the TIMER pin to GND
for a brief period, resets this condition.
IRSENSE
The duty cycle of this automatic retry cycle is set to the ratio of
2 μA/60 μA, which approximates 3.8% on. The value of the
timer capacitor determines the on time of this cycle. This time
is calculated as follows:
5µA
VTIMER
60µA
tON = 1.3 × CTIMER/60 μA
tOFF = 1.1 × CTIMER/2 μA
VGSFET
VOUT
2µA
SHORTCIRCUIT
EVENT
COMP2
VTIMER
COMP1
05124-005
IRSENSE
Figure 36. ADM1170-2 Latch Off After Overcurrent Fault
60µA
100µA
SOFT START
VGSFET
COMP2
FAULT
CYCLE
COMP1
FAULT
CYCLE
05124-004
VOUT
SHORTCIRCUIT
EVENT
Figure 35. ADM1170-1 Automatic Retry During Overcurrent Fault
AUTOMATIC RETRY OR LATCHED OFF
The ADM1170 is available in two models. The ADM1170-1
has an automatic retry system whereby when a current fault is
detected, the FET is shut down after a time determined by the
timer capacitor, and it is switched on again in a controlled continuous cycle to determine if the fault remains (see Figure 35
for details). The period of this cycle is determined by the timer
capacitor at a duty cycle of 3.8% on and 96.2% off.
The inrush current profile is controlled using an external
capacitor on the soft start (SS) pin. During power on reset, the
SS pin is held at GND. When the pass FET begins to conduct
current, a pull-up current source is initiated on the SS pin and
charges the voltage on the soft start capacitor in a linear fashion.
The current limit of the device is porportional to the voltage on
the SS pin until it reaches 1 V. When the voltage on the SS pin
reaches 1 V the current limit reaches the normal operating
condition of VSENSE = 50 mV. The voltage on the SS pin
continues to rise past the 1 V level with no effect on the current
limit. The reference voltage for the GATE linear control
amplifier is derived from the soft start voltage, such that the
inrush linear current limit is defined as
ILIMIT = VSS/(20 × RSENSE)
This provides a limit of 50 mV across RSENSE when VSS is at 1 V.
Therefore, the value for the SS capacitor is chosen as follows:
CSS = ISS × t
where ISS = 10 μA and t is the time required for the current limit
to ramp up.
Rev. 0 | Page 13 of 16
ADM1170
OUTLINE DIMENSIONS
2.90 BSC
8
7
6
5
1
2
3
4
1.60 BSC
2.80 BSC
PIN 1
INDICATOR
0.65 BSC
1.95
BSC
*0.90
0.87
0.84
*1.00 MAX
0.10 MAX
0.38
0.22
0.20
0.08
SEATING
PLANE
8°
4°
0°
0.60
0.45
0.30
*COMPLIANT TO JEDEC STANDARDS MO-193-BA WITH
THE EXCEPTION OF PACKAGE HEIGHT AND THICKNESS.
Figure 37. 8-Lead Thin Small Outline Transistor Package [TSOT]
(UJ-8)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADM1170-1AUJZ-RL7 1
ADM1170-2AUJZ-RL71
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
8-Lead TSOT
8-Lead TSOT
Z = Pb-free part.
Rev. 0 | Page 14 of 16
Package Option
UJ-8
UJ-8
Branding
M1H
M1J
ADM1170
NOTES
Rev. 0 | Page 15 of 16
ADM1170
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05124-0-7/06(0)
Rev. 0 | Page 16 of 16